Administrator's Guide HP Session Allocation Manager (SAM) v.2.1

Default value is 0 (all bits off). For example, to turn off the Cancel and Minimize buttons and leave
the Close button on, set the value to 3.
●
DisplayShutdown—integer value, 0 or 1. When set to 1, an Action button is added to the client
user interface. This is the same button created by the DisplayShutdown, DisplayRestart, and
DisplayLogoff options. If the button already displays from another option setting, the Shutdown
option is added to the button drop-down. Not valid for Blade Workstation Client series. The default
value is 0 (do not show).
●
DisplayRestart—integer value, 0 or 1. When set to 1, an Action button is added to the client user
interface. This is the same action button created by the DisplayShutdown, DisplayRestart, and
DisplayLogoff options. If the button already displays from another option setting, the Restart
option is added to the button drop-down. Not valid for Blade Workstation Client series. The default
value is 0 (do not show).
●
DisplayLogoff—integer value, 0 or 1. When set to 1, an Action button is added to the client user
interface. This is the same action button created by the DisplayShutdown, DisplayRestart, and
DisplayLogoff options. If the button already displays from another option setting, the Logoff option
is added to the button drop-down. Not valid for Blade Workstation Client series. The default value
is 0 (do not show).
●
DefaultSessionAction—integer value, 0, 1, or 2. When set to 0, the default session action
(pressing the button without dropping down the list) for the button is Shutdown. If set to 1, the
default action is Restart. If set to 2, the default action is Logoff. If only one action is enabled, that
option is the default action, and this setting is ignored. If this value corresponds to an action that
is not enabled, no default action is available. Not valid for Blade Workstation Client series. The
default value is 0.
●
ConnectionBar.FollowMouse—integer value, 0 or 1. When set to 1, the connection bar is open
on the monitor where the cursor is. The default value is 1.
●
ConnectionBar.Location—integer value. Sets the location of connection bar (if 0, top; if 1, bottom;
if 2, left; if 3, right). The default value is 0 (top).
●
ConnectionBar.EnableAddNew—integer value, 0 or 1. When set to 1, enables the “Add New”
button on the connection bar. The default value is 1.
●
ConnectionBar.EnableCloseAll—integer value, 0 or 1. When set to 1, enables the “Disconnect
All” button on the connection bar. The default value is 1.
●
ConnectionBar.EnableDisconnectInstance—integer value, 0 or 1. When set to 1, enables the
“Disconnect” button on the connection bar for each session. The default value is 1.
●
ConnectionBar.EnableReconnectInstance—integer value, 0 or 1. When set to 1, enables the
“Reconnect” button on each connection bar for each session. The default value is 1.
●
ConnectionBar.ShowDelay
—integer value. Specifies delay in milliseconds for connection bar to
appear after cursor has been moved to screen edge. The default value is 500 milliseconds.
●
ConnectionBar.ShowOnDisconnect—integer value, 0 or 1. When set to 1, enables connection
bar to appear automatically when a session closes. The default value is 1.
●
ConnectionBar.AutoHideTimeout—integer value. Sets time in seconds for connection bar to
stay open when cursor is moved off connection bar. 0 = always stays open. The default value is
3.
●
Resolutions—string value. Specifies another section in the .SAM file that contains a list of
resolutions to show on the client UI. Open the default .SAM file to see the required format.
Install and Validate the HP SAM Client Software 21