HP 9000 rp8420 Server - User Service Guide, Fifth Edition

Table 1-6 PCI-X Slot Types

Device

SlotI/O Partition

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot8

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot70

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot60

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot50

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot40

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot30

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot20

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot10

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot8

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot71

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot61

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot51

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot41

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot31

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot21

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3 V connector, Hot-Plug Slot11

1 If the slot is used as a PCI slot, then either the 33MHz or 66MHz PCI frequency is supported. If the slot is used as a

PCI-X slot, then either the 66MHz or 133MHz PCI-X frequency is supported.

2 This is a single rope between the SBA and LBA and not a dual rope like that seen for ropes 1–7.

Core I/O Card

Up to two core I/O cards can be plugged into the HP 9000 rp8420 server. Two core I/O cards

allows for two I/O partitions to exist in the HP 9000 rp8420 server. The server can have up to

two partitions but the total number of partitions possible in a server with the Server Expansion

Unit attached is four.

The core I/O card is can be replaced with standby power applied. The system power to the core

I/O is handled in the hardware the same way a hot-plug PCI/PCI-X card is handled. Standby

power to core I/O is handled by power manager devices to limit inrush current during insertion.

Mass Storage (Disk) Backplane

Internal mass storage connections to disks are routed on the mass storage backplane, having

connectors and termination logic. All hard disks are hot-plug while removable media disks are

not hot-plug. The HP 9000 rp8420 server accommodates two internal, removable media devices.

Therefore, power connectors for a removable media device are required on the mass storage

backplane. For more information, See Figure 1-12.

Detailed HP 9000 rp8420 server Description 33