Basic Operation Guide 2013/06
Table Of Contents
- Switch Software
- Contents
- 1 Commands found in the Basic Operation Guide
- 2 Getting started
- 3 Using the Menu Interface
- 4 Using the Command Line Interface (CLI)
- Overview
- Accessing the CLI
- Using the CLI
- Return message types with CLI commands
- CLI interactive commands
- CLI control and editing
- 5 Using the HP WebAgent
- 6 Switch memory and configuration
- Overview
- Configuration file management
- Using the CLI to implement configuration changes
- Creating a custom default configuration
- Using the menu and WebAgent to implement configuration changes configuration file
- Zeroization
- Using Primary and Secondary flash image options
- Multiple configuration files
- Display configuration of selected interface
- Automatic configuration update with DHCP Option 66
- 7 Interface access and system information
- 8 Configuring IP addressing
- Overview
- IP configuration
- Loopback interfaces
- IP Preserve: retaining VLAN-1 IP addressing across configuration file downloads
- Configuring a single source IP address
- 9 Software management
- Downloading switch documentation and software from the web
- Viewing or downloading the software manual set
- Downloading software updates for your switch
- Software signing and verification
- Saving configurations while using the CLI
- Important: Best Practices for software updates
- Updating the switch: overview
- Updating the switch: detailed steps
- Rolling back switch software
- Viewing or transferring alternate configuration files
- Downloading switch documentation and software from the web
- Index
F
factory default configuration
restoring, 54
fastboot command, 71
fault detection policy, 47
flash memory, 22, 50
flow control
terminal, 95
G
gateway
configuring, 107
default gateway, 105
IP address, 106, 107
manual config priority, 112
on primary VLAN, 106
precedence of manual gateway over DHCP/Bootp, 112
global config level, 110
H
Help
for CLI, 33
for menu interface, 20, 22
hop, router, 111
hostname parameter, 103
I
idle-timeout, 95, 99
in-band
managing the switch, 9
inactivity-timer, 99
interactive mode
Banner motd cmd, 39
menu commands, 38
interactive mode, CLI, 37
IP
CLI access, 107
configuration, 105
DHCP/Bootp, 105
effect when address not used, 111
features available with and without, 111
gateway, 105
gateway (IP) address, 106
menu access, 107
multinetting, 105
multiple addresses in VLAN, 105, 109
single source addressing, 121
source IP address, 121
source-interface command, 122
subnet, 105, 108
subnet mask, 105, 107
Time-To-Live, 107
TTL, 107
IP address
Configured IP address, 122
Configured IP interface, 122
configuring, 10
displaying source IP information, 123
displaying source-interface status, 122
loopback interface configuration, 115
manually configure, 107
multiple in a VLAN, 109
outgoing interface, 122
quick start, 106
removing or replacing, 110
setup screen, 106
show management command, 108
single source, 121
source IP address, 121
source IP with debug, 126
source IP with radius, 125
source IP with tacacs, 126
source-interface option, 121
IP perserve
summary of effect, 120
IP preserve
DHCP server, 118
overview, 117
rules, operating, 118
K
kill command, 100
L
link, serial, 95
loopback interface
benefits, 114
default, 114
multiple interfaces supported, 114
lost password, 48
M
MAC address, 113
manager access, 29
manager password, 47
manager privileges, 29
memory
flash, 22, 50
startup configuration, 22
menu interface
configuration changes, saving, 22
moving to or from the CLI, 30
see also console
message
types, 36
module
not present with stacking, 24
module not present, 24
multinetting, 109
see also ACLs
multiple configuration file see configuration file, multiple
O
oobm
telnet, 96
telnet-server, 96
tftp traffic, 83
transferring files, 83
141