EtherExpressTM Pro/10+ ISA PCLA8205B Installation Guide
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
1 Connecting to a Netware 3.12 Server Windows for Workgroups Version 3.11 1 Connecting to a Netware 3.12 Server Windows for Workgroups Version 3.11 Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • Intel EtherExpress Pro 10+ ISA 10MBS Ethernet adapter card and drivers disk. • Vectra VL8 and VL7 Driver Name: EPRO.386 Size: 16K Date: 10/22/96. • Vectra VE7/VE8 Driver Name: EPROODI.INS Size: 784B Date: 10/26/95. • Novell Netware 3.
1 Connecting to a Netware 3.12 Server Windows for Workgroups Version 3.11 listed above under the heading “Device Configuration.” 6 If changes are required, save those changes and exit. 7 Remove the Intel drivers diskette, insert Netware client for DOS and MS-Windows disk 1. 8 Execute INST_DOS.EXE. If you are using a Vectra VL8, enter yes to accept the agreement and then continue from step 9. If you are using a Vectra VL7 or VE8, follow the steps below and then continue from step 16.
1 Connecting to a Netware 3.12 Server Windows for Workgroups Version 3.11 ❒ C:\NOVELL\CLIENT32 ❒ C:\WINDOWS ❒ 16-bit LAN drivers ❒ Intel EtherExpress ™ PRO/10 15 Press “F10” to save and continue. 16 When prompted, insert the corresponding disks to complete file transfer and driver installation. 17 When the install utility is finished, press to restart the machine. 18 After Windows loads, open the “NETWORK” folder, and double-click the “NETWORK SETUP” icon.
1 Connecting to a Netware 3.12 Server Windows for Workgroups Version 3.
1 Connecting to a Netware 3.12 Server Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • Intel EtherExpress Pro 10+ ISA Ethernet card and drivers disk. • Driver Name for Vectra VL8 and VE7/VE8: NETPRO.INF Size: 12KB Date: 4/25/97. • Driver Name for Vectra VL7: EPRO.SYS Size: 11KB Date: 6/3/97. • Novell Netware 3.12 server that supports Net BEUI,TCP/IP, NWLink IPX/ SPX, and NWLink NetBIOS transfer protocols.
1 Connecting to a Netware 3.12 Server Windows 95 SR2 8 Power on the machine and allow it to boot to Windows 95 SR2. If you are using a Vectra VL8 or VL7, go directly to step 9. If you are using a Vectra VE7/VE8, follow the instructions below and then go to step 16. a Click on "Start" then "Settings" and open the "Control Panel." b Double-click on the "Network" icon and click on "Add." c Select "Adapter" and click on "Add.
1 Connecting to a Netware 3.12 Server Windows 95 SR2 15 Click on “Close” button, and files will copy. 16 When prompted for the file “NETAPI.DLL”, set the path to your Windows 95 files and click “OK.” (For HP preloaded HDD’s, set the path to C:\WIN95.SR2\) 17 Click on the “Yes” button to finish the installation and restart your computer.
1 Connecting to a Netware 3.
2 Connecting to a Netware 4.11 Server Windows for Workgroups Version 3.11 2 Connecting to a Netware 4.11 Server Windows for Workgroups Version 3.11 Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • Intel EtherExpress Pro 10+ ISA 10MBS Ethernet adapter card and drivers disk. • Vectra VL8 and VL7 Driver Name: EPRO.386 Size: 16K Date: 10/22/96 • Vectra VE7/VE8 Driver Name: EEPRODI.INS Size: 784B Date: 10/26/95 • Novell Netware 4.
2 Connecting to a Netware 4.11 Server Windows for Workgroups Version 3.11 listed above under the heading “Device Configuration.” 6 If changes are required, save those changes and exit. 7 Remove the Intel drivers diskette, insert Netware client for DOS and MSWindows disk 1. 8 Execute INST_DOS.EXE and enter yes to accept the agreement if using a Vectra VL8, then continue to step 9. If using a Vectra VL7 or VE7/VE8, follow the instructions below, then go to step 18.
2 Connecting to a Netware 4.11 Server Windows for Workgroups Version 3.11 ❒ C:\NOVELL\CLIENT32 ❒ C:\WINDOWS ❒ 16-bit LAN drivers ❒ Intel EtherExpress ™ PRO/10 15 Press “F10” to save and continue. 16 When prompted, insert the corresponding disks to complete file transfer and driver installation. 17 When the install utility is finished, press to restart the machine. 18 After Windows loads, open the “NETWORK” folder, and double-click the “NETWORK SETUP” icon.
2 Connecting to a Netware 4.11 Server Windows for Workgroups Version 3.
2 Connecting to a Netware 4.11 Server Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • Intel EtherExpress Pro 10+ ISA Ethernet card and drivers disk Ver. 3.5. • Vectra VL8 and VE7/VE8 Driver Name: NETPRO.INF Size: 12KB Date: 4/25/97 • Vectra VL7 Driver Name: EPRO.SYS Size:11KB Date: 6/3/97 • Novell Netware 3.12 server that supports Net BEUI,TCP/IP, NWLink IPX/ SPX, and NWLink NetBIOS transfer protocols.
2 Connecting to a Netware 4.11 Server Windows 95 SR2 8 Power on the machine and allow it to boot to Windows 95 SR2. If you are using a Vectra VE7/VE8, follow the instructions below to complete the procedure. If you are using a VL8 or VL7, go directly to step 9. a Click on "Start" then "Settings" and open the "Control Panel." b Double-click on the "Network" icon and click on "Add." c Select "Adapter" and click on "Add.
2 Connecting to a Netware 4.11 Server Windows 95 SR2 13 Click “OK” to the “Network” dialog box to provide computer / work group names. 14 Specify your Computer Name, Workgroup, and Computer Description. (If you do not have the required information, contact your network administrator.) 15 Click on “Close” button, and files will copy. 16 When prompted for the file “NETAPI.DLL”, set the path to your Windows 95 files and click “OK.” (For HP preloaded HDD’s, set the path to C:\WIN95.
2 Connecting to a Netware 4.
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Version 3.11 3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Version 3.11 Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • Intel EtherExpress Pro 10+ ISA Ethernet adapter card and drivers disk Ver. 3.5. • Driver Name: EPRO.386 Size: 16K Date: 10/22/96 • Microsoft Windows NT server 3.51 machine that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
Windows for Workgroups Version 3.11 7 Remove the Intel drivers diskette and reboot the machine. 8 After Windows loads, open the “NETWORK” program group, and doubleclick the “Network Setup.” 9 Select the “Networks” button in the “Network Setup” dialog box. 10 Click on the “Install Microsoft Windows Network:” option, and click “OK.” 11 Click the “Drivers” button from the “Network Setup” dialog box, and click on “Add Adapter.” 12 Click “OK” to accept the default choice of “Unlisted or Updated Network Adapter.
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Version 3.11 20 When prompted for the file “EPRO.DOS”, insert the Intel EtherExpress drivers disk Ver. 3.5”, and set the path to “A:\NDIS\.” (If you have an HP-preloaded HDD, set path to “C:\Masters\LanDrv\Pro10\NDIS\”For Vectra VE7/VE8 users, the path is "C:\Masters\LanDrv\Pro10P\WFW") 21 Finish the network card installation by clicking on “OK” in the “Network Setup” message.
Windows for Workgroups Version 3.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 • Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk. • Driver Name: PROW95.VXD Size: 6K Date: 8/7/96 • Microsoft Windows NT Server 3.51 machine that supports Net BEUI,TCP/ IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 If you are using a Vectra VE7/VE8, follow the instructions below to complete the procedure. If you are using a VL8 or VL7, go directly to step 9. a Click on "Start" then "Settings" and open the "Control Panel." b Double-click on the "Network" icon and click on "Add." c Select "Adapter" and click on "Add." d Click on "Have Disk", insert the Intel Etherexpress Pro10+ drivers disk and set the path to "A:\.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 names. 14 Specify your Computer Name, Workgroup, and Computer Description. (If you do not have the required information, contact your network administrator.) 15 Click on “Close” button, and files will copy. 16 When prompted for the file “NETAPI.DLL”, set the path to your Windows 95 files and click “OK.” (For HP preloaded HDD’s, set the path to C:\WIN95.SR2\) 17 Click on the “Yes” button to finish the installation and restart your computer.
3 Connecting to a Windows NT Server 3.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 Windows NT Workstation Version 3.51 Requirements • HP Vectra with Microsoft Windows NT Workstation 3.51 installed. • Intel EtherExpress Pro 10+ ISA Ethernet card and drivers disk. • Driver Name: EPRO.SYS Size: 10KB Date: 4/14/97 • Microsoft Windows NT Workstation 3.51 and Service Pack Media. • Microsoft Windows NT Server 3.51 machine that supports Net BEUI, TCP/ IP,NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 on “Control Panel.” 9 Select the “Network” icon, and click “YES” to install NT networking. 10 Insert the Windows NT Workstation CD. 11 In the “Windows NT Setup”, set the path to your NT files, and click on the “Continue” button.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 Setup” dialog box.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 4.0 Windows NT Workstation Version 4.0 Requirements • HP Vectra with Windows NT Workstation 4.0 Service Pack 3. • Intel EtherExpress PRO/10+ ISA Ethernet card and drivers disk. • Driver Name: EPRO.SYS Size: 11KB Date: 4/14/97 • Microsoft Windows NT Workstation 4.0 and Service Pack Media. (If you have a Hewlett-Packard preloaded HDD, the media is located at “C:\I386”) • Microsoft Windows NT Server 3.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 4.0 7 Remove the Intel drivers diskette and reboot the machine. 8 Power on the machine and allow it to boot to Windows NT Workstation 4.0. 9 Log onto the machine with administrator privileges. (If you do not have the required information, contact your network administrator.) 10 Click on “Start” and move to “Settings”, open the “Control Panel” group and double-click the “Network” Icon.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 4.0 25 When “Windows NT is now ready to start the network…” click on “Next.” 26 Specify your Computer Name, Workgroup or Domain and click on “Next.” (If you do not have the required information, contact your network administrator.) 27 After “Network has been installed on this computer” click on “Finish.” 28 To complete the installation, select “Yes” to reboot your computer.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 4.
4 Connecting to a Windows NT Server 4.0 Windows for Workgroups Version. 3.11 4 Connecting to a Windows NT Server 4.0 Windows for Workgroups Version. 3.11 Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • Intel EtherExpress Pro 10+ ISA Ethernet adapter card and drivers disk Ver. 3.5. • Driver Name: EPRO.386 Size: 16K Date: 10/22/96 • Microsoft Windows NT server 4.0 machine that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
4 Connecting to a Windows NT Server 4.0 Windows for Workgroups Version. 3.11 7 Remove the Intel drivers diskette and reboot the machine. 8 After Windows loads, open the “NETWORK” program group, and doubleclick the “Network Setup.” 9 Select the “Networks” button in the “Network Setup” dialog box. 10 Click on the “Install Microsoft Windows Network:” option, and click “OK.” 11 Click the “Drivers” button from the “Network Setup” dialog box, and click on “Add Adapter.
4 Connecting to a Windows NT Server 4.0 Windows for Workgroups Version. 3.11 20 When prompted for the file “EPRO.DOS”, insert the Intel EtherExpress drivers disk Ver. 3.5”, and set the path to “A:\NDIS\.” (If you have an HP-preloaded HDD, set path to “C:\Masters\LanDrv\Pro10\NDIS\”. For Vectra VE7/VE8 users, the path is "C:\Masters\LanDrv\Pro100P\WFW".) 21 Finish the network card installation by clicking on “OK” in the “Network Setup” message.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2. • Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk. • Driver Name: PROW95.VXD Size: 6K Date: 8/7/96 • Microsoft Windows NT Server 4.0 machine that supports Net BEUI,TCP/ IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2 If you are using a Vectra VE7/VE8, follow the instructions below to complete the installation. If not, go directly to step 9. a Click on "Start" then "Settings" and open the "Control Panel." b Double-click on the "Network" icon and click on "Add." c Select "Adapter" and click on "Add." d Click on "Have Disk", insert the Intel Etherexpress Pro10+ drivers disk and set the path to "A:\.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2 14 Specify your Computer Name, Workgroup, and Computer Description. (If you do not have the required information, contact your network administrator.) 15 Click on “Close” button, and files will copy. 16 When prompted for the file “NETAPI.DLL”, set the path to your Windows 95 files and click “OK.” (For HP preloaded HDD’s, set the path to C:\WIN95.SR2\) 17 Click on the “Yes” button to finish the installation and restart your computer.
4 Connecting to a Windows NT Server 4.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51 Windows NT Workstation Version 3.51 Requirements • HP Vectra with Microsoft Windows NT Workstation 3.51 installed. • Intel EtherExpress Pro 10+ ISA Ethernet card and drivers disk Ver. 3.5. • Driver Name: EPRO.SYS Size: 10KB Date: 4/14/97 • Microsoft Windows NT Workstation 3.51 and Service Pack Media. • Microsoft Windows NT Server 4.0 machine that supports Net BEUI, TCP/ IP,NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51 on “Control Panel.” 9 Select the “Network” icon, and click “YES” to install NT networking. 10 Insert the Windows NT Workstation CD. 11 In the “Windows NT Setup”, set the path to your NT files, and click on the “Continue” button.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51 23 To complete the installation, remove the floppy disk, and click on “Restart Computer” button in the “Windows NT Workstation Networking Setup” dialog box.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 Windows NT Workstation 4.0 Requirements • HP Vectra with Windows NT Workstation 4.0 Service Pack 3. • Intel EtherExpress PRO/10+ ISA Ethernet card and drivers disk ver. 3.5. • Driver Name: EPRO.SYS Size: 11KB Date: 4/14/97 • Microsoft Windows NT Workstation 4.0 and Service Pack Media. (If you have a Hewlett-Packard preloaded HDD, the media is located at “C:\I386”) • Microsoft Windows NT Server 4.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 7 Remove the Intel drivers diskette and reboot the machine. 8 Power on the machine and allow it to boot to Windows NT Workstation 4.0. 9 Log onto the machine with administrator privileges. (If you do not have the required information, contact your network administrator.) 10 Click on “Start” and move to “Settings”, open the “Control Panel” group and double-click the “Network” Icon.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 24 At the “Show Bindings for:” prompt, accept default settings and click on “Next.” 25 When “Windows NT is now ready to start the network…” click on “Next.” 26 Specify your Computer Name, Workgroup or Domain and click on “Next.” (If you do not have the required information, contact your network administrator.) 27 After “Network has been installed on this computer” click on “Finish.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.
Version Number Intel Pro10+ Rev.
