Modem and Local Area Network User Guide
© Copyright 2007 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Product notice This user guide describes features that are common to most models. Some features may not be available on your computer.
iv Product notice ENWW
Table of contents 1 Using the modem (select models only) Connecting a modem cable .................................................................................................................. 2 Connecting a country-specific modem cable adapter .......................................................................... 3 Selecting a location setting ...................................................................................................................
vi ENWW
1 Using the modem (select models only) The modem must be connected to an analog telephone line using a 6-pin, RJ-11 modem cable. In some countries, a country-specific modem cable adapter is also required. Jacks for digital PBX systems may resemble analog telephone jacks, but they are not compatible with the modem. WARNING! Connecting the internal analog modem to a digital line can permanently damage the modem. Immediately disconnect the modem cable if you accidentally connect it to a digital line.
Connecting a modem cable WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a modem or telephone cable into the RJ-45 (network) jack. To connect a modem cable: 2 1. Plug the modem cable into the modem jack (1) on the computer. 2. Plug the modem cable into the RJ-11 telephone wall jack (2).
Connecting a country-specific modem cable adapter Telephone jacks vary by country. To use the modem and the modem cable outside the country in which you purchased the computer, you must obtain a country-specific modem cable adapter. To connect the modem to an analog telephone line that does not have an RJ-11 telephone jack, follow these steps: ENWW 1. Plug the modem cable into the modem jack (1) on the computer. 2. Plug the modem cable into the country-specific modem cable adapter (2). 3.
Selecting a location setting Viewing the current location selection To view the current location setting for the modem, follow these steps: 4 1. Select Start > Control Panel. 2. Click Date, Time, Language, and Regional Options. 3. Click Regional and Language Options. 4. Your location is displayed under Location.
Adding new locations when traveling By default, the only location setting available to the modem is a location setting for the country in which you purchased the computer. As you travel to different countries, set the internal modem to a location setting that meets the operating standards of the country in which you are using the modem. As you add new location settings, they are saved by the computer so that you can switch among settings at any time. You can add multiple location settings for any country.
Solving travel connection problems If you experience modem connection problems when using the computer outside of the country in which you purchased it, try the following suggestions. ● Check the telephone line type. The modem requires an analog, not a digital, telephone line. A line described as a PBX line is usually a digital line. A telephone line described as a data line, fax machine line, modem line, or standard telephone line is usually an analog line. ● Check for pulse or tone dialing.
7. Clear the check box for Wait for dial tone before dialing. 8. Click OK twice. Using preinstalled communication software To use preinstalled modem software for terminal emulation and data transfer: ENWW 1. Select Start > All Programs > Accessories > Communications. 2. Click a fax or terminal emulation program or Internet connection wizard.
2 Connecting to a local area network Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (not included). If the network cable contains noise suppression circuitry (1), which prevents interference from TV and radio reception, orient the circuitry end of the cable (2) toward the computer. To connect the network cable: 1. Plug the network cable into the network jack (1) on the computer. 2. Plug the other end of the cable into a network wall jack (2).
Index C cable LAN 8 modem 2 country-specific modem cable adapter 3 L local area network (LAN) cable required 8 connecting cable 8 M modem cable connecting 2 country-specific cable adapter 3 noise suppression circuitry 1 modem software setting/adding location 4 travel connection problems 6 N network cable connecting 8 noise suppression circuitry 8 noise suppression circuitry modem cable 1 network cable 8 T troubleshooting modem 6 W wireless network (WLAN) 8 ENWW Index 9
