Battery warning The battery for this car camcorder is sealed internally. DO NOT attempt to disassemble the camcorder and remove the battery. Always charge using the provided system. Improper charging of the battery may result in explosion. The battery is designed for this camcorder and is not customer replaceable. Batteries may explode if exposed to naked fire. Never expose the car camcorder in a fire. Recycle the camcorder observing local regulations. Notes on Installation 1.
1 Introduction 1.1 Package Contents The package contains the following items. In case there is any missing or damaged item, contact your dealer immediately.
1.2 Product Overview Front View Top and Bottom Views 6 7 1 8 9 10 5 Side (Left and Right) Views Rear View 2 12 4 11 3 13 No. Item No.
2 Getting Started 2.1 Inserting the Memory Card Insert the memory card with the gold contacts facing the back of the camcorder. Push the memory card until it clicks into place. To remove the memory card Push to eject the memory card out of the slot. Note: 1. Do not remove or insert the memory card when the camcorder is turned on. This may damage the memory card. 2. Please use a 32GB, Class 10 or above Micro SD card. 3. Please format the micro SD cards before the initial use. 4.
2.2 Installing in Vehicles 2.2.1 Mount to Windshield 1. Attach the bracket to the camcorder. Slide it into the bracket holder until you hear a click. 2. With the suction-cup laying flat, position the suction-cup on the windshield. 3. Hold the base firmly on the windshield and press down the clamp to mount the car holder to the windshield. Make sure the base is securely locked in place.
2.2.2 Adjust the camcorder position 1. Loose the knob to swivel the camcorder vertically. Knob 2. Loose the knob to swivel the camcorder horizontally up to 360°. Knob 3. Then tighten the knob to make sure the camcorder is securely locked in place.
2.3 Connecting to Power Use only the supplied car adapter to power up the camcorder and charge the built-in battery. 1. 2. Connect one end of the car adapter to the USB connector of the camcorder. Plug the other end of the car charger to the cigarette lighter socket of your vehicle. Once the vehicle engine is started, the camcorder automatically turns on. Note: 1.
2.4 Powering the Camcorder On / Off 2.4.1 Auto Power On/Off Once the vehicle engine is started, the camcorder automatically turns on. If the Automatic Record function is enabled, the recording will automatically start right after the camcorder turns on. 2.5 Initial Settings Before using the camcorder, we recommend you to enable the Automatic Record function and set up the correct date and time. 2.5.
3 Using the Car Recorder 3.1.1 LDWS (Lane Departure Warning Systems) When LDWS (Lane Departure Warning Systems) is activated, the camcorder gives an audible and visual alert on the display when the speed reaches a set limit and/or the vehicle deviates from the lane. To set the LDWS (Lane Departure Warning Systems), do the following: button to enter the OSD menu. 1. Press the 2. Press the / button to select LDWS and press the button. 3.
3.1.2 Motion Detection If Motion Detection is activated, when power off the camcorder, the system alert message, “Press OK Key to Power off, or enter motion detection after 10sec.”, will pop on the screen. This means the system will enter Motion Detection automatically in 10 seconds; when the camcorder detects any motion in front of lens, Video Record will be activated for a duration the same as the length setting. To set the motion detection, do the following: 1. Press the button to enter the OSD menu. 2.
3.2 Playback Videos and Photos To playback videos and photos, do the following: 1. If recording is in progress, press the The standby screen is displayed. 2. Press the 3. Press the / button to select the file category that you want to browse and press the button. 4. Press the / button to view the next or the previous file and press the button to view the file in full screen. button to stop recording. button to enter the OSD menu.
3.2.1 Deleting Files To delete file(s), do the following: 1. If recording is in progress, press the 2. Press the 3. Press the button. 4. Press the / button to select the file category and press the button. 5. Press the / button to select the file that you want to delete and press button to enter the Delete the menu. 6. Press the option. button to enter the OSD menu. / / button to select File Deletion and press the button to select an Item 7.
電池注意事項 僅可使用本系統充電,未正確處理電池可能會引發爆炸。 請勿自行拆裝、穿刺電池,或使電池短路。 電池接觸明火可能會引起爆炸,請勿將電池丟棄到火中。 請根據當地法規妥善處理使用過的電池。 此電池為內置嚴禁自行更換電池 此電池為內置嚴禁自行更換電池, 嚴禁自行更換電池,欲更換電池請洽經銷商。 欲更換電池請洽經銷商。 安裝須知 本產品之安裝應靠近後視鏡,以獲得最佳的視野。 確定鏡頭是在檔風玻璃雨刷的範圍內,確保視野良好,即使雨天亦然。 不要用手指碰觸鏡頭。手指上的油垢可能會留在鏡頭上,導致錄像或 攝影不清楚。定期清潔鏡頭。 不要將產品安裝在有色車窗上。因為這樣會損壞淺色薄膜。 確定安裝位置不會受有色車窗的阻礙。 1
1 導論 1.
1.
2 開始 2.1 插入記憶卡 以黃金接觸點面向設備的背面,插入記憶卡。推記憶卡直到咔嗒一聲, 插入定位時止。 取出記憶卡 取出記憶卡 推記憶卡,彈出插槽。 註: 1. 設備在開機狀態時,不要取出或插入記憶卡,以免損壞記憶卡。 2. 請使用 Micro SD 卡 10 級, 最高支援 32GB。 3. 使用前請先格式化 Micro SD 卡。 4. 若錄影中螢幕顯示"卡速過慢",表示設備中的記憶卡寫入速度過慢,請更換卡 速較高的記憶卡。 5.
2.2 安裝於車內 2.2.1 置於擋風玻璃上 1. 將托架基座推入設備上方的托架插孔 中,直到聽到咔嗒聲固定。 2. 將托架的吸盤輕壓於擋風玻璃上,再 按下托架的夾子固定托架。 3.
2.2.2 調整設備位置 1. 鬆開旋鈕,將設備垂直方向調整。 旋鈕 2. 鬆開旋鈕,將設備水平方向調整 (360度)。 旋鈕 3.
2.3 連接電源 只使用所供應之電源連接器,啟動設備以及為內建之電池充電。 1. 2. 將電源連接器的一端連接設備的USB接頭。 將電源連接器的另一端插接汽車內的香煙點火器的插孔。汽車引 擎一旦發動,設備即自動開機。 註: 1. 本設備僅適用產品所附之電源連接器,請勿使用其他廠牌以免設備燒毀或導 致電池爆炸。 2. 首次使用設備請將電池的電量充滿。 3.
2.4 設備開/ 設備開/關 2.4.1 自動開/關 自動開 關 汽車引擎一旦發動,則設備即自動開機。若啟動自動記錄功能,則在 設備開機後,即開始自動錄影 。 2.5 首次設定 在使用設備之前,我們建議先啟動自動錄影功能,設定正確的日期與 時間。 2.5.
3 使用行車記錄器 3.1.1 車道偏移偵測 若啟用車道偏移偵測 車道偏移偵測,當行車達設定時速且 偏離車道時,設備會發出提示音與警示畫面 提醒。 設定車道偏移偵測,其方式如下: 1. 按 2. 按 3. 按 / 按鈕選擇所需的時速設定 (關 / 80km/h / 90km/h / 100km/h),並且調整設備使錄影畫面中的車道與車道偏移校正圖 示 按鈕,進入 OSD 目錄。 / 按鈕選擇車道偏移偵測 車道偏移偵測 ,再按 相重疊,再按 按鈕。 按鈕完成設定。 時速設定 車道偏移 車道偏移 校正圖示 圖示 校正 4.
3.1.2 移動偵測 若啟用移動偵測 移動偵測,當行車記錄器關閉電源時,螢幕上會出現 ”按OK鍵 移動偵測 將關機, 將關機 ,或10秒後進入移動偵測“ 。指經過 10 秒後系統會自動進 入移動偵測模式,當設備偵測到鏡頭前任何物體移動時會自動啟動錄 影,持續錄影的時間同影片長度的設定。 設定移動偵側,其方式如下: 1. 按 按鈕,進入 OSD 目錄。 2. 按 / 按鈕選擇移動 移動偵測 移動偵測 ,再按 3. 按 / 按鈕選擇 開,再按 4. 按 按鈕。 按鈕。 按鈕,退出目錄。 註: 1. 在電池充滿與狀態良好的情況下,移動偵測可連續錄影時間約 30 分鐘。 2. 電池的蓄電能力會隨著設備使用逐漸減少,此為電池的正常現象。 3. 當設備進入移動偵測模式,螢幕將於 30 秒後關閉。 3.1.3 緊急錄影 在錄影期間再按一次 按鈕將會進入 緊急錄影模式,並於螢幕左上角會顯示 " 緊急錄影" 字樣,在緊急錄影模式中錄下 的檔案會被保護起來。 按下 ▼ 即會停止錄影。 註: 1. 若啟動碰撞偵測 功能,並偵測到碰撞,則設備會自動啟用緊急錄影。 2.
3.2 播放影片 播放影片與照片 影片與照片 播放影片與照片,其方式如下: 1. 若正在錄影,須先按 按鈕停止錄影,顯示待機螢幕。 2. 按 3. 按 / 按鈕,選取您要瀏覽的檔案 類別,再按 按鈕。 4.
3.2.1 檔案刪除 檔案刪除 檔案刪除,其方式如下: 1. 若正在錄影,須先按 按鈕,停止錄影。 2. 按 3. 按 / 按鈕選取檔案刪除 檔案刪除,再按 檔案刪除 按鈕。 4. 按 / 按鈕選取檔案類別,再按 按鈕。 5. 按 / 按鈕,選取您想要刪除的檔 案,再按 按鈕,進入刪除目錄。 6. 按 按鈕,進入 OSD 目錄。 按鈕,選取一個選項。 / 項目 7.
电池警告 请务必使用随附的系统进行充电。电池处置不当可能导致爆 炸。 切勿拆卸电池或在电池上钻孔,切勿使电池短路。 电池暴露在明火下可能爆炸。处理电池时切勿放入火中。 请按照当地法规处理废电池。 此 电池为 电池 为内 置切勿自行更换电池, 切勿自行更换电池,请交由经销商进行更换。 安装需知 1. 本产品应安装在靠近后视镜之处,并尽量接近前挡风玻璃中央位 置,以获得最好的视野。 2. 确定镜头是在档风玻璃雨刷的范围内,确保视野良好,即使雨天 也同样好。 3. 不要用手指触摸镜头。手指上的油脂可能会留在镜头上,导致摄 像或摄影不清楚。定期清洁镜头。 4. 不要将产品安装在有色车窗上。因为这样会损坏浅色薄膜。 5. 确定安装位置不会受有色车窗的阻碍。 6.
1 介绍 1.
1.
2 入门 2.1 插入存储卡 插入 存储卡 以黄金接触点面向设备的背面,插入记忆卡。推记忆卡直到咔嗒的一 声,插入到位时止。 取出存储卡 取出存储卡 推存储卡,弹出插槽。 註: 1. 设备在开机状态时,不要取出或插入存储卡,以免损坏存储卡。 2. 请使用 Micro SD 卡 10 级,最高支持 32GB。 3. 使用前请先格式化 Micro SD 存储卡。 4. 若摄像中屏幕显示"卡速过慢",表示设备中的存储卡卡速过慢不敷使用,请立 即停止摄像并更换卡速较高的存储卡,以避免造成无效的摄像或文件损坏。 5.
2.2 安装在 安装 在 车内 2.2.1 固定在 固定 在挡风玻璃上 1. 将托架基座推入设备上方的托架插孔 中,直到听到咔嗒声固定。 2. 将托架的吸盘轻压于挡风玻璃上,再按 下托架的夹子固定托架。 3.
2.2.2 调整设备位置 1. 松开旋钮,将设备垂直方向调整。 旋钮 2. 松开旋钮,将设备水平方向调整 (360度)。 旋钮 3.
2.3 连接电源 只使用所提供的汽车适配器,启动设备以及为内置的电池充电。 1. 2. 将汽车适配器的一端连接到设备的 USB 端口。 将汽车充电器的另一端插接汽车内的香烟点火器的插孔。汽车引 擎一旦发动,设备即自动开机。 注: 1. 本设备仅适用产品所附之电源适配器,请勿使用其他厂牌以免设备烧毁或导致 电池爆炸。 2. 首次使用设备请将电池的电量充满。 3.
2.4 设备开/ 设备开 /关 2.4.1 自动开/ 自动开/关 汽车引擎一旦发动,设备就自动开机。如果启动自动记录 自动记录功能,则在 自动记录 设备开机后,即开始自动摄像。 2.5 初始设 初始 设 置 在使用设备之前,我们建议先打开自动 自动摄像 摄像 功能,设置正确的日期与 时间。 2.5.
3 使用行车记录仪 使用行车记录仪 3.1.1 车道偏移侦测 若开启车道偏移侦测 车道偏移侦测, 车道偏移侦测 当行车达设置时速 且偏离车道时,设备会发出警示音与警示 画面提醒。 播放摄像,其方式如下: 1. 按 按钮进入 OSD 菜单。 2. 按 / 按钮选取车道偏移侦测 车道偏移侦测,再按 车道偏移侦测 3. 按 / 按钮选择所需的时速设置 (关 / 80km/h / 90km/h / 按钮。 100km/h),并且调整设备使拍摄画面中的车道与车道偏移校正图 示 相重迭,再按 按钮完成设置。 时速设置 车道偏移 校正图示 4.
3.1.2 运动探测 若开启运动探测功能,当行车记录仪关机時,屏幕会出现 ”按 OK 键 将关机,或 10 秒后进入运动探测” 。指经过 10 秒后系统会自动进 入运动探测模式,当设备侦测到镜头前任何物体移动时会自动启动摄 像。 开机后打开自动摄像,其设置方式如下: 1. 按 2. 按 / 按钮进入 OSD 菜单。 按钮选择运动探测 运动探测,再按 运动探测 3. 按 / 按钮选择 开 ,再按 4. 按 按钮。 按钮。 按钮,弹出菜单。 注: 1. 在电池充满与状态良好的情况下,运动探测可连续摄像时间约 30 分钟。 2. 电池的蓄电能力会随着设备使用逐渐减少,此为电池的正常现象。 3. 当设备进入运动探测模式,屏幕将于 30 秒后关闭。 3.1.3 紧急摄像 紧急 摄像 在摄像期间再按一次 按钮将会进入 紧急摄像模式,并于屏幕左上角会显示 " 紧急摄像 " 字样,在紧急摄像模式中录下 的文件会被保护起来。 按下 按钮即会停止摄像。 注: 1. 若启动碰撞侦测 功能并侦测到碰撞,则设备会自动启用紧急摄像。 2.
3.2 播放视频 播放 视频与照片 视频 与照片 播放视频与照片,其方式如下: 1. 如果正在摄像,需先按 2. 按 3. 按 按钮进入 OSD 菜单。 / 按钮选取您要浏览的文件 类型,再按 4.
3.2.1 删除文件 删除 文件 删除文件,其方式如下: 1. 如果正在摄像,需先按 2. 按 3. 按 按钮停止摄像。 按钮,进入 OSD 菜单。 / 按钮,选取文件删除 文件删除,再按 文件删除 按钮。 4. 按 / 按钮,选取文件类型,再按 按钮。 5. 按 / 按钮,选取您想要删除的文 件,再按 6. 按 / 按钮,进入删除菜单。 按钮,选取一个选项。 项目 7.