HP Deskjet F2100 All-in-One series Basics Guide
Hewlett-Packard Company notices The information contained in this document is subject to change without notice. All rights reserved. Reproduction, adaptation, or translation of this material is prohibited without prior written permission of Hewlett-Packard, except as allowed under copyright laws. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
1 HP All-in-One overview The HP All-in-One at a glance....................................................................................................2 Control panel buttons.................................................................................................................3 Status light overview...................................................................................................................4 Load originals for scanning and copying..........................................
1 HP All-in-One overview The HP Deskjet F2100 All-in-One series is a versatile device that gives you easy-to-use copying, scanning, and printing. For information about the full range of features and functions, see the onscreen Help.
Label Icon Name and Description 1 On: Turns the HP All-in-One on or off. The On button is lit when the HP Allin-One is powered on. 2 Cancel: Stops a print, copy, or scan job. 3 Check Paper light: Indicates the need to load paper or remove a paper jam. The button next to this light is the Resume button. In certain situations (for example, after clearing a paper jam), this button resumes the job.
Chapter 1 Status light overview Several indicator lights inform you of the status of the HP All-in-One. HP All-in-One overview Label Description 1 On button 2 Check Paper light 3 Check Print Cartridge light 4 Plain Paper Type light 5 Photo Paper Type light The following table describes common situations and explains what the lights mean. Light status What it means All lights are off. The HP All-in-One is turned off. Press the On button to turn on the device.
(continued) Light status What it means NOTE: Your printer might be packaged with only a tri-color print cartridge. The On, Check Paper, and Check Print Cartridge lights are blinking. Scanner failure. All lights are blinking. The HP All-in-One has a fatal error. Turn off the HP All-in-One, then on again. If the problem persists, contact HP Support. 1. 2. 3. 4. Turn the HP All-in-One off. Unplug the power cord. Wait a minute, then plug the power cord back in. Turn the HP All-in-One back on.
Chapter 1 To make a copy from the control panel 1. Make sure you have paper loaded in the input tray. 2. Place your original print side down on the left front corner of the glass. 3. Press Start Copy Black or Start Copy Color. Scan an original For original documents or images placed on the glass, you can start a scan from your computer or from the HP All-in-One. To use the scan features, the HP All-in-One and computer must be connected and turned on.
2 Troubleshooting and support This chapter contains troubleshooting information for installation and configuration issues and some operational topics. For more troubleshooting information, see the onscreen Help. Many issues are caused when the HP All-in-One is connected to the computer using a USB cable before the HP All-in-One software is installed on the computer.
Chapter 2 3. 4. Double-click HP Uninstaller. Follow the onscreen instructions. After the software is uninstalled, disconnect the HP All-in-One, and then restart your computer. NOTE: It is important that you disconnect the HP All-in-One before restarting your computer. Do not connect the HP All-in-One to your computer until after you have reinstalled the software. 5. 6. 7. To reinstall the software, insert the HP All-in-One CD-ROM into your computer’s CD-ROM drive.
I connected the USB cable, but I am having problems using the HP All-in-One with my computer Solution: You must first install the software that came with the HP All-in-One before connecting the USB cable. During installation, do not plug in the USB cable until prompted by the onscreen instructions. Connecting the USB cable before prompted can cause errors. Once you have installed the software, connecting your computer to the HP All-in-One with a USB cable is straightforward.
Chapter 2 • If you are connecting the HP All-in-One through a USB hub, make sure the hub is turned on. If the hub is on, try connecting directly to your computer. • Check other printers or scanners. You might need to disconnect older products from your computer. • Try connecting the USB cable to another USB port on your computer. After you check the connections, try restarting your computer. Turn the HP All-in-One off and then on again.
Onscreen Help The onscreen Help provides detailed instructions on features of your HP All-in-One that are not described in this guide, including features that are only available using the software you installed with your HP All-in-One. To access the HP Photosmart Software Help on a Windows computer 1. In the HP Solution Center, click the tab for the HP All-in-One. 2. In the Device Support area, click Onscreen Guide or Troubleshooting.
3 Technical information The technical specifications and international regulatory information for the HP All-in-One are provided in this section. System requirements Software system requirements are located in the Readme file. Paper specifications • • Input tray capacity: Plain paper sheets: Up to 100 (20 lb. paper) Output tray capacity: Plain paper sheets: Up to 50 (20 lb. paper) NOTE: For a complete list of supported media sizes, see the printer software.
Technical information Warranty Warranty 13
Chapter 3 Technical information 14 Technical information
