User Guide
Table Of Contents
- Purpose
- Readership
- Part Numbers
- Conventions
- Safety Precautions
- Table of Contents
- Troubleshooting
- Introduction
- Troubleshooting System Error Codes
- Performing a Service Test on a Failed Assembly
- Performing the Necessary Service Calibrations or Adjustments
- Solving Print Quality Problems
- The Printer does not Power ON
- Cover Sensors are not Working
- The File Sent is Not Processed Immediately
- Paper Jams Occur Frequently
- Print Speed is Very Slow
- No Ink Message when there is Enough Ink
- Abnormal Sound Coming from the Printer
- Front Panel is Not Working
- Heater Panel is Not Working
- Solving Heater Problems
- Special Power On Procedure
- Both NVRAM and Main PCA are Replaced Together
- System Error Codes
- System Error Codes
- Printhead Adjustment
- Introduction
- Tools Required
- Calibrate the Printhead Adjustment Jig
- Install the Printhead Adjustment Jigs in the Carriage
- Set Printhead Voltage
- Print the Printhead Adjustment Pattern
- Perform Printhead Position Correction
- Print the Check Printhead Pattern
- Adjust the Printhead
- Tip to Speed-Up the Printhead Adjustment
- Maintenance Mode
- Introduction
- Diagnostics - Self Test
- Phone Support
- Maintenance Mode Menus
- Entering the Maintenance Mode
- Basic Menu Operation
- P. ADJ. (Printer Adjustment)
- PH. ADJ (Printhead Adjustment)
- PH. MAIN (Printhead Maintenance)
- MNFG-PRN (Manufacturing Patterns)
- SETUP
- FEED
- SENSORS
- ELECT (Electronics)
- VOLT (Voltage Check)
- MOTORS
- SYSTEM INF
- COUNTER
- Heater Panel Maintenance Mode
- Adjustments and Calibrations
- Adjustments
- Calibrations
- Belt Tension Adjustment
- Carriage Height Adjustment
- Scan-Axis Belt Tension Adjustment
- Paper-Axis Belt Tension Adjustment
- Wiping Station Height Adjustment
- Wiper Belt Tension Adjustment
- Wiper Blade Height Adjustment
- Capping Station Height Adjustment
- Carriage Shield Height Adjustment
- Wiping Position Calibration
- Capping Position Calibration
- Line Sensor Calibration (Side Margin)
- Line Sensor Calibration (Top Margin)
- Print Quality
- Print Quality Troubleshooting Actions
- Print Quality General Advice
- Using the IQ Print to Troubleshoot
- Horizontal Lines Across the Image (Banding)
- Images are Blurred
- Bleeding, Repelling or Mottling Problems
- Image is Completely Blank or Faded
- Output Only Contains a Partial Print
- The Printer Area is Stained
- Part of Image is Missing at the Start of the Print
- Print Quality is not Improved After Printhead Recovery
- Parts and Diagrams
- Removal and Installation
- Introduction
- Rear Cover
- Upper Side Cover (Left or Right)
- Top Side Cover (Left or Right)
- Top Cover
- Lower Side Cover (Left or Right)
- Left Subtank Cover
- Right Subtank Cover
- Lower Capping Cover
- Capping Door
- Lower Wiping Cover
- Wiping Door
- Ink Cartridge Door (Left or Right)
- Rear Ink Cartridge Cover (Left or Right)
- Electronics Module Cover
- Firmware Access Cover
- Front Panel
- Heater Panel
- Front Heater
- Rear Heater
- Center Platen
- Vacuum Fan
- Main PCA
- NVRAM
- Head Relay Board
- Power Supply Unit
- Heater Relay Assembly
- Waste Bottle Sensor
- End-of-Media Sensor
- Front Media Sensor
- Rear Media Sensor
- Media Lever Sensor
- Rear Cover Sensor
- Home Position Sensor
- Paper-Axis Motor and Belt
- Scan-Axis Motor and Belt
- Carriage Drive Assembly (Includes Carriage Belt)
- Encoder Strip
- Trailing Cable
- Printhead Cooling Fans
- Printhead
- Printhead Connector Assembly
- Carriage PCA
- Encoder Sensor
- Line Sensor
- Ink Pump Assembly
- Ink Supply Station (Left or Right)
- IC Door Sensor (Left or Right)
- Subtank Sensors
- Capping Station Assembly
- Capping Unit
- Prime Assembly
- Solenoid Assembly
- Wiping Station Assembly
- Wiper Cleaning Assembly
- Wiper Blade
- Wiper Belts
- Pinchwheel Assembly
- Preventive Maintenance
5-23
Adjustments and Calibrations
HP Designjet 9000s Series Printer Service Manual
Wiping Position Calibration
This calibration must be performed whenever:
Wiping Station is disassembled or replaced.
Wiper Blade is disassembled or replaced.
Wiper Belts are disassembled or replaced.
Perform the Wiping Position Calibration as follows:
1 Enter into the Maintenance Mode ⇒ Page 4-7.
2 Move the Carriage Assembly to the Wiping Station ⇒ Page 4-18.
3 Enter into the "Wipe Position" Menu ⇒ Page 4-13.
This adjustment must be performed when the Carriage is at
the Wiping Station. Do NOT move the Carriage when the
Wiper Blade is raised as this could damage the Printheads.
4 Manually rotate the Wiper Blade using the Wiping Station Gear until the
Wiper Blade touches the Printheads (image is shown without the Carriage
positioned in the Wiping Station). Remove the necessary covers in order to
get access to the Wiping Station Gear.
5 Check that the center of the Wiper Blades are aligned with the center of the
Printheads.
# WIPE POSITION
> +0.0 mm
Wiper Blade
Wiper Station Gear
Wiper Blade
Printhead