HP Data Protector software A.06.00 Installation and Integration Guidelines for Data Protector Cell Manager on HP UX 11.
Index Introduction......................................................................................................................................... 3 Installation of Veritas Cluster products .................................................................................................... 3 Configuring SSH or remsh before installing products ............................................................................ 3 Enabling SSH...................................................................
Introduction This document describes how to install and configure Data Protector 06.00 Cell Manager with Veritas Cluster on an HP-UX 11.23 platform. Veritas Cluster Server by Symantec software is a high-availability solution for cluster configuration. Veritas Cluster Server (VCS) monitors system and application services, and restart services when hardware or software fails, See Figure 1 for more details.
Enabling SSH The SSH program enables you to log into and execute commands on a remote system. SSH enables encrypted communications and an authentication process between two un-trusted hosts over an insecure network. SSH is the preferred method of remote communication because it provides a greater level of security than the remote shell suite of protocols. The following is an example of an SSH setup procedure: 1. Log in as root on the source system from which you want to install the Veritas product. 2.
Uploading /.ssh/id_dsa.pub to /id_dsa.pub 12. To quit the SFTP session, enter: sftp> quit 13. To begin the ssh session on the target system, enter: # ssh target_sys 14. Enter the root password at the prompt: password: 15. After logging in, enter the following command to append the authorization key to the id_dsa.pub file: # cat /.ssh/id_dsa.pub >> /.ssh/authorized_keys 16. To delete the id_dsa.
For more information about remote shell configuration, see the Operating System documentation and the remsh (1M) manual page. Installation methods for Veritas Cluster products There are two ways to install Veritas products: Using the product installer Invoking product installation scripts from the command line For more information about the other installation methods, see the product installation guide.
Symantec Product Version Installed Licensed Veritas Cluster Server 4.1 yes Veritas Volume Replicator no no Veritas Storage Foundation 4.
9) Symantec Product Authentication Service b) Back to previous menu Select a product to install: [1-9, b, and q] q Select “b” (“back”) to return to a previous section of an installation procedure. This feature is contextsensitive, so it returns to the beginning of a grouped section of questions. If an installation procedure does not respond, use Control–c to stop and exit the program. 6. Enter the number of the product to install and press Return.
See the concepts guide: http://bizsupport.austin.hp.com/bc/docs/support/SupportManual/c00751562/c00751562.pdf and to installation guide: http://bizsupport.austin.hp.com/bc/docs/support/SupportManual/c00751873/c00751873.pdf Veritas Cluster Integration As part of its high-availability support, Data Protector provides a full integration of the Data Protector Cell Manager with Veritas Cluster on HP-UX systems.
Decide which systems are going to be the Primary Cell Manager and the Secondary Cell Managers. All of them must have Veritas Cluster Software installed and must be configured as cluster members. Data Protector Cell Manager with recommended patches and all other Data Protector Software components required for the integrations in the cluster must be installed on the primary node and each of the Secondary nodes. .
For more information, see HP OpenView Storage Data Protector Product Announcements, Software Notes, and References. Install Data Protector to the linked directories to overcome the shortage of space in the server. Have sufficient disk space (about 2% of the planned data to be backed up) for the Internal Database. See HP OpenView Storage Data Protector Product Announcements, Software Notes, and References.
Optionally, you can install Data Protector from a depot on the disk: To copy the DP_DEPOT, AUTOPASS, and LOCAL_INSTALL directories, where the installation files are stored, to your local disk, run: # mkdir # cp -r /dvdrom//DP_DEPOT # cp -r /dvdrom//AUTOPASS # cp -r /dvdrom//LOCAL_INSTALL Where is: hpux_ia for HP-UX 11.
# /opt/omni/ -> //opt/omni/ # /var/opt/omni/ -> //var/opt/omni/ # /etc/opt/omni/ -> //etc/opt/omni/ You must create the links before the installation and ensure that the destination directories exist.
If Oracle8 is installed on cluster nodes, HP recommends stopping Oracle8 database services on the cluster nodes. Installation procedure The cluster client setup is the same as for the Windows local client setup, except that the cluster Administrator account is required to perform the installation. In addition to the Data Protector client components such as Disk Agents and Media Agents, install the Cluster Integration component, which is selected by default during the installation.
See the HP OpenView Storage Data Protector Installation and Licensing Guide for instructions. Configuring the Primary and Secondary Cell Managers The following sections describe how to configure the Primary and Secondary Cell Managers. The following sections provide step-by-step examples to configure the Primary and Secondary Cell Managers. Directory and file names, numbers, and other variables will differ from the following examples according to the environment.
For More Information HP Data Protector software www.hp.com/go/dataprotector HP Data Protector software support matrix http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?lang=en&cc=us&taskId=101&prod ClassId=1&contentType=SupportManual&docIndexId=179911&prodTypeId=18964&prodSeriesId=3241176 © Copyright 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice.
