HP DesignJet T2500 Multifunction Printer Series - Introductory Information

Introductory In
f
ormatio
n
5
English
Message or code Recommendation
61:08 Resend the job.
61:08.1 The job cannot be print
ed because it is password-protected.
61:08.2 The job cannot be printed because it contains errors. Resend the job from the
Embedded Web Server.
61:09 Resend the job.
63:10 r 7XUQRƫWKHSULQWHUXVLQJWKH3RZHUEXWWRQDWWKHIURQW
r 7XUQRƫWKHSRZHUVZLWFKDWWKHUHDU
r Disconnect the power cord.
r Reconnect the power cord and turn on the printer.
r Check that the network cable is correctly connected.
r (QVXUHWKDWWKHSULQWHUoVƭUPZDUHLVXSWRGDWH
63:20 A potential problem has been detected in the network interface.
r 7XUQRƫWKHSULQWHUXVLQJWKH3RZHUEXWWRQDWWKHIURQW
r 7XUQRƫWKHSRZHUVZLWFKDWWKHUHDU
r Disconnect the power cord.
r Reconnect the power cord and turn on the printer.
r Send the same job to the printer again.
r (QVXUHWKDWWKHSULQWHUoVƭUPZDUHLVXSWRGDWH
71.03, 71.08 Out of memory. To avoid this, in the HP-GL/2 driver select the Advanced tab
and then Send job as a bitmap.
74.01 $QHUURURFFXUU
HGZKHQORDGLQJWKHƭUPZDUHXSGDWHƭOH
r 7XUQRƫWKHSULQWHUXVLQJWKH3RZHUEXWWRQDWWKHIURQW
r 7XUQRƫWKHSRZHUVZLWFKDWWKHUHDU
r Disconnect the power cord.
r Reconnect the power cord and turn on the printer.
r 5HORDGWKHƭUPZDUHXSGDWHƭOHLQWRWKHSULQWHU
74.1:04 7U\WKHƭUPZDUHXSGDWHDJDLQ'RQRWWU\WRXVH\RXUFRPSXWHUZKLOHWKH
update is in progress.
74.8:04 7KHƭUPZDUHXSGDWHKDVIDLOHG<RXUƭUPZDUHƭOHPD\EHLQFRUUHFWWU\WR
download it again.
75.11:10 Preventive maintenance 1 is recommended.
75.21:10 Preventive maintenance 2 is recommended.
76:03 The printer’s hard disk is full. You may want to use Disk Wipe to free some
space.
78:08 Borderless printing not possible; setting ignored. Ensure that the loaded paper
supports borderless printing.
79:03, 79:04 8SGDWH\RXUSULQWHUoVƭUPZDUH
81:01 Lift the scanner and make sure that there are no obstacles restricting the
movement of the drive roller. If the paper has jammed, clear the obstruction by
following the instructions in the front panel.
86:01 Lift the scanner and make sure that there are no obstacles restricting the
movement of the printhead’s carriage. If the paper has jammed, clear the
obstruction by following the instructions in the front panel.
94, 94.1 Restart color calibration.