Hardware Guide hp compaq notebook series Document Part Number: 309971-001 April 2003 This guide explains how to identify and use notebook hardware features, including connectors for external devices. It also includes power and environmental specifications, which may be helpful when traveling with the notebook.
© 2003 Hewlett-Packard Company Microsoft and Windows are trademarks of Microsoft Corporation in the U.S. and/or other countries. Intel and SpeedStep are trademarks of Intel Corporation in the U.S. and/or other countries. SD Logo is a trademark. HP shall not be liable for technical or editorial errors or omissions contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents 1 Notebook Features Pointing Device Components ........................................... 1–1 Top Components .............................................................. 1–3 Left Side Components ...................................................... 1–5 Right Side Components.................................................... 1–6 Front View Components................................................... 1–7 Rear Panel Components ...................................................
Contents Using Quick Launch Buttons................................................ Keypads .......................................................................... Using the Internal Keypad ....................................... Using an External Keypad ....................................... 2–10 2–11 2–11 2–12 3 Battery Packs Inserting or Removing the Primary Battery Pack............. 3–2 Using the Optional Travel Battery ...................................
Contents 5 Audio and Video Using Audio Features ....................................................... Adjusting the Volume ................................................ Using the Microphone Input Jack .............................. Using the Audio Line-Out Jack ................................. Using Video Features ....................................................... Connecting a Device to the S-Video Out Jack........... Changing the Video Mode .........................................
Contents 8 Hardware Upgrades Using PC Cards ................................................................ 8–1 Inserting a PC Card.................................................... 8–2 Removing a PC Card ................................................. 8–2 Using SD Cards ................................................................ 8–4 Inserting an SD Card.................................................. 8–4 Removing an SD Card ...............................................
1 Notebook Features Pointing Device Components Pointing Device Components Item Component Description 1 Pointing stick Moves the pointer and selects or activates items on the screen. 2 Left and right pointing stick buttons Function like the left and right buttons on an external mouse.
Notebook Features Pointing Device Components (Continued) Item Component Description 3 TouchPad Moves the pointer and selects or activates items on the screen. Can be set to perform other mouse functions, such as scrolling and double-clicking. 4 Left and right TouchPad buttons Function like the left and right buttons on an external mouse.
Notebook Features Top Components Top Components Item Component Description 1 Quick Launch buttons (3) Enable you to access common functions with a single keystroke. 2 Power button When the notebook is* Off, press and release to turn on the notebook. In Standby, press and release to exit Standby. In Hibernation, press and release to exit Hibernation. If the system has stopped responding and Windows shut down procedures cannot be used, press and hold for 5 seconds to turn off the notebook.
Notebook Features Top Components (Continued) Item Component Description 3 Volume control buttons Increase, decrease, and mute the system volume. 4 Function keys Execute frequently used system functions when pressed in combination with the Fn key. 5 Applications key Displays shortcut menu for items beneath the pointer. 6 Display release latch recess Secures the display when it is closed. 7 Microsoft logo key Displays the Windows Start menu.
Notebook Features Left Side Components Left Side Components Item Component Description 1 Infrared port Links another IrDA-compliant device for wireless communication. 2 PC Card eject button Ejects an optional PC Card from the PC Card slot. 3 PC Card slot Supports optional Type I or Type II 32bit (CardBus) or 16-bit PC Cards. 4 Secure Digital (SD) slot Accepts SD memory cards used as removable storage devices.
Notebook Features Right Side Components Right Side Components Item Component Description 1 Security cable slot Attaches an optional security cable to the notebook. 2 Hard drive bay Holds the primary hard drive. 3 Exhaust vent Enables airflow to cool internal components. To prevent overheating, do not obstruct vents. Using the notebook on a soft surface, such as a pillow, blanket, rug, or thick clothing may block airflow.
Notebook Features Front View Components Front View Components Item 1 Component Description Antenna (2) Send and receive wireless Local Area Network (LAN) signals. The antenna covers are not removeable. Removing the covers can cause damage to the antenna. 2 Display release latch Opens the notebook. 3 Microphone Inputs single-channel sound.
Notebook Features Rear Panel Components Rear Panel Components Item 1-8 Component Description 1 S-Video out jack Connects an optional S-Video device, such as a television, VCR, camcorder, overhead projector, or video capture card. 2 External monitor connector Connects an optional external monitor or overhead projector. 3 USB connector Connects USB 1.1- and 2.0-compliant devices to the notebook using a standard USB cable. 4 Self-powered USB connector Connects USB 1.1- and 2.
Notebook Features Rear Panel Components (Continued) Item Component Description 5 DC power connector Connects an AC Adapter or an optional Automobile Power Adapter/Charger, Aircraft Power Adapter, or DC cable. 6 RJ-45 jack Connects a network cable. 7 RJ-11 jack Connects a modem cable. 8 Rear panel connector cover Closes to cover the connectors. This cover can be removed by removing the screws that secure it to the notebook.
Notebook Features Bottom Components Bottom Components Item Component Description 1 Travel battery connector Connects the optional travel battery bay. The travel battery connector has a plastic cover that must be opened before connecting the travel battery bay. 2 Docking connector Connects the notebook to an optional Port Replicator. 3 Mini PCI compartment Contains the mini PCI wireless card. 4 Intake vents Enable airflow to cool internal components.
Notebook Features Bottom Components (Continued) Item Component Description 5 Battery release latch Releases the primary battery pack from the battery bay. 6 Quick Check button Displays the percentage of a full charge remaining on a battery pack using the Quick Check lights. 7 Battery power gauge Indicates the charge remaining on a battery pack. 8 9 Battery bay Holds the primary battery pack. Memory expansion compartment Contains 1 memory expansion slotfor optional memory expansion boards.
Notebook Features Lights Lights Item Component Description 1 Hard drive activity On: The hard drive is being accessed. 2 Num lock On: Num lock is on or the embedded numeric keypad is enabled. 3 Caps lock On: Caps lock is on. 4 Scroll lock On: Scroll lock is on. 5 Wireless on/off On: The wireless mini PCI card and/or Bluetooth are on. Off: The wireless mini PCI card and Bluetooth are off.
Notebook Features Lights (Continued) Item Component Description 6 Power/Standby On: Power is turned on. Blinking: Notebook is in Standby. 7 Battery On: A battery pack is charging. Blinking: A battery pack that is the only available power source has reached a low-battery condition. When the battery reaches a critical low-battery condition, the battery light begins blinking more quickly.
2 Pointing Devices and Keyboard Using a Pointing Device By default, the pointing stick and TouchPad components can be used interchangeably.
Pointing Devices and Keyboard Pointing Device Components 2-2 Item Component Description 1 Pointing stick Moves the pointer and selects or activates items on the screen. 2 Left and right pointing stick button Functions like the left and right buttons on an external mouse. 3 TouchPad Moves the pointer and selects or activates items on the screen. Can be set to perform other mouse functions, such as scrolling, selecting, and double-clicking.
Pointing Devices and Keyboard Using the Pointing Stick To move the pointer, press the pointing stick in the direction you want to move the pointer. Use the left and right pointing stick buttons as you would the left and right buttons on an external mouse. To change the pointing stick cap: 1. Turn off the notebook. 2. Gently pull off the used pointing stick cap. 3. Push a replacement cap, included with the notebook, into place.
Pointing Devices and Keyboard Using an External Mouse An external USB mouse can be connected to the notebook using one of the USB connectors on the back panel. An external PS/2 or USB mouse can be connected to the system using the connectors on an optional Port Replicator Setting Pointing Device Preferences Mouse Properties in Windows enables you to change custom settings for pointing devices, including: Enabling or disabling a pointing device.
Pointing Devices and Keyboard Using Hotkeys and Shortcut Keys Hotkeys and shortcut keys, which are preset combinations of the Fn key and another key, execute frequently used system functions. Fn and Function Keys Fn and function keys Item 1 2 Component Fn key Function keys A hotkey is a combination of the Fn key and one of the function keys. The icons on the function keys represent the hotkey functions available on your notebook.
Pointing Devices and Keyboard Hotkey and Shortcut Key Quick Reference Function Key Combination to Activate Function Key Combination to DeactivateFunction Initiate Standby Fn+F3 Power button Switch display and image Fn+F4 Fn+F4 View battery information Fn+F8 Fn+F8 Adjust the screen brightness to a lower level Fn+F9 N/A Adjust the screen brightness to a higherlevel Fn+F10 N/A Display system information Fn+esc Fn+esc 2-6 User Guide
Pointing Devices and Keyboard Initiating Standby (Fn+F3) The Fn+F3 hotkeys are set at the factory to initiate Standby. When the notebook is on, press the Fn+F3 hotkeys to initiate Standby. When Standby is limited, your work is saved in random access memory (RAM), the screen is cleared, and power is conserved. While the notebook is in Standby, the power/Standby light blinks. To exit Standby, briefly press the power button.
Pointing Devices and Keyboard Viewing Battery Charge Information (Fn+F8) Press Fn+F8 to display charge information for all installed battery packs. The display indicates which battery packs are charging and reports the amount of charge remaining in each battery pack. Battery pack locations are indicated by number: Location 1 is the primary battery pack. Location 2 is the travel battery pack.
Pointing Devices and Keyboard Using Hotkeys and Shortcut Keys with External Keyboards The following hotkeys and shortcut keys can be used as described with external keyboards: Fn+esc Fn+F8 To use hotkeys or shortcut keys on an external keyboard, press the scroll lock key twice, then the other key of the hotkey combination. For example, to use the Fn+F8 hotkeys, press scroll lock+scroll lock+F8.
Pointing Devices and Keyboard Using Quick Launch Buttons The 6 Quick Launch buttons enable you to access common functions with a single keystroke. Quick Launch buttons Item Component Description 1 QuickLock button Disables the keyboard and pointing device and clears the display. Before you can use QuickLock, you must set a password and select preferences. For more information, refer on this CD to the Software Guide, “Security” chapter.
Pointing Devices and Keyboard Keypads The notebook has an internal numeric keypad and supports an optional external numeric keypad or an optional external keyboard that includes a numeric keypad. Using the Internal Keypad The 15 keys of the embedded numeric keypad can be used like the keys on an external keypad. When the internal keypad is turned on, each key on the internal keypad performs the functions indicated by the icon in the upper right corner of the key.
Pointing Devices and Keyboard Enabling and Disabling the Internal Keypad Press Fn+num lk to enable the embedded numeric keypad. The num lock light turns on. Press Fn+num lk again to return the keys to their standard keyboard functions. The numeric keypad cannot be enabled while an optional external keyboard or keypad is connected to the notebook or to an optional Port Replicator.
Pointing Devices and Keyboard When num lock mode on an external keypad is turned on, the num lock light on the notebook turns on. When the num lock mode on an external keypad is turned off, the num lock light on the notebook turns off. If the external keypad is connected, the internal keypad cannot be turned on. Enabling or Disabling Num Lock Mode as You Work To turn num lock on or off on an external keypad as you work, press the num lk key on the external keypad, not on the notebook.
Pointing Devices and Keyboard 5. Press F10. 6. To save your preference and exit Computer Setup, select File > Save Changes and Exit, then follow the instructions on the screen. Your preference is set as you exit Computer Setup and is in effect when the notebook restarts.
3 Battery Packs This notebook supports up to 2 lithium ion battery packs, the primary battery and an optional travel battery. The same type of battery pack can be used in the notebook battery bay and the optional travel battery.
Battery Packs Inserting or Removing the Primary Battery Pack The notebook battery bay holds the primary battery pack. CAUTION: To prevent the loss of information when removing a battery pack, when it is the only power source available to the system, initiate Hibernation or shut down the notebook before removing the battery pack. To insert the primary battery pack: 1. Align the battery pack with the notebook battery bay. 2. Insert the battery pack tabs into the battery bay recesses.
Battery Packs 3. Snap the battery pack into place. Inserting the primary battery pack 4. Turn the notebook over and open the display. If the notebook is in Hibernation, press the power button to resume operation.
Battery Packs To remove the primary battery pack: 1. Close the display and turn the notebook bottom-side up. 2. Slide the battery release latch 1. 3. After the battery pack tilts upward, remove it from the battery bay 2.
Battery Packs Using the Optional Travel Battery The optional travel battery attaches to the bottom of the notebook. The optional travel battery kit includes the following items: Travel battery caddy Battery pack Documentation Inserting or Removing the Battery Pack To insert the battery pack into the travel battery caddy: 1. Align the battery pack with the travel battery caddy. 2. Insert the battery pack tabs into the travel battery caddy recesses.
Battery Packs 3. Snap the battery pack into place. Inserting the battery pack into the travel battery caddy To remove the battery pack from the travel battery caddy: 1. Eject the battery pack from the travel battery caddy by sliding the battery release latch 1. 2. When the battery pack tilts upward, remove it from the travel battery caddy 2.
Battery Packs Attaching or Detaching the Travel Battery To attach the optional travel battery to the notebook: 1. Open the travel battery connector on the bottom of the notebook by sliding the cover toward the rear panel of the notebook.
Battery Packs 2. Insert the tabs on the travel battery caddy into the recesses on the bottom of the notebook. Inserting the travel battery caddy tabs into the notebook recesses 3. Press the travel battery caddy onto the notebook until it snaps into place.
Battery Packs 4. Lock the travel battery onto the notebook by sliding the locking switch.
Battery Packs To detach an optional travel battery from the notebook: 1. Unlock the travel battery from the notebook by sliding the locking switch 1. 2. Press the release latch 2. 3. Lift the travel battery up and away from the notebook 3. Detaching the travel battery from the notebook Charging a Battery Pack Multiple battery packs in the system charge and discharge in a preset sequence: Charge sequence 1. Notebook battery bay 2. Travel battery Discharge sequence 1. Travel battery 2.
Battery Packs The primary battery pack charges when it is inserted into the notebook and the notebook is connected to external power. External power can be supplied through an AC Adapter, the optional Port Replicator, or an optional Automobile Power Adapter/Charger. The battery pack in the travel battery charges when it is attached to the notebook and the notebook is connected to external power. External power can be supplied through an AC Adapter or an optional Automobile Power Adapter/Charger.
Battery Packs To charge the primary battery pack: 1. Insert the battery pack into the notebook. 2. Connect the notebook to AC power. (The battery light turns on.) 3. Leave the notebook connected to AC power until the battery light turns off, signaling that the battery pack is fully charged. To charge the battery pack in the travel battery: 1. Insert the battery pack into the travel battery caddy. 2. Attach the travel battery to the notebook. 3. Connect the notebook to AC power. (The battery light turns on.
Battery Packs Displaying Charge Information on the Screen To display battery charge information on the screen, use the Power meter feature of the operating system: Select Start > Control Panel > Performance and Maintenance icon > Power Options icon > Power Meter tab. or Select the Power meter icon in the system tray. To display the Power meter icon in the system tray: 1. Select Start > Control Panel > Performance and Maintenance icon > Power Options icon > Advanced tab. 2.
Battery Packs Displaying Charge Information on a Battery Pack The battery Quick Check feature enables you to check the battery pack charge information without having to turn on the notebook. You do not have to remove a battery pack from the notebook battery bay or the travel battery to check the charge information; however, you must detach the travel battery from the notebook to check the charge of the travel bay battery pack.
Battery Packs Battery Pack Quick Check Indications Indication Percent of a Full Charge Remaining 4 lights on 76 to 100% 3 lights on 51 to 75% 2 lights on 26 to 50% 1 light on 11 to 25% 1 light blinking 1 to 10% Managing Low-Battery Conditions Some low-battery condition alerts and system responses can be changed in the Power Options Properties window of the operating system. The information in this chapter describes the alerts and system responses set at the factory.
Battery Packs Critical Low-Battery Condition If a low-battery condition is not resolved, the notebook enters a critical low-battery condition (one percent of a full charge). In a critical low-battery condition: If Hibernation is enabled and the notebook is on or in Standby, the notebook initiates Hibernation. If Hibernation is disabled and the notebook is on or in Standby, the notebook remains in Standby until there is no power, then shuts down and loses your unsaved work.
Battery Packs Plug an optional Aircraft Power Adapter into the notebook and into the in-seat power supply available on some commercial aircraft. (The optional Aircraft Power Adapter can run the notebook but cannot charge a battery power.) Dock the notebook in an optional Port Replicator. When No Power Source Is Available To resolve a low-battery condition when no power source is available, select one of the following options: Initiate Hibernation.
Battery Packs When to Calibrate Calibrate an in-use battery pack whenever battery status displays seem inaccurate or whenever the battery pack has not been used for one month or more. It should not be necessary to calibrate any battery pack, even if it is heavily used, more than once a month, unless usage patterns change significantly. It is not necessary to calibrate a new battery pack before first use. How to Calibrate To manually calibrate a battery pack: 1. Fully charge the battery pack. 2.
Battery Packs Stop or remove a PC Card or SD card that you are not using. Use the Fn+F9 and the FN+F10 hotkeys to quickly lower and raise screen brightness as you need it. Use optional powered speakers instead of the internal speakers, or use the volume buttons to quickly raise and lower system volume as needed. Turn off a device connected to the S-Video connector by using the Fn+F9 hotkeys or by turning off support for the device in Windows. Run the notebook on external power while formatting a diskette.
Battery Packs Storing a Battery Pack If a notebook will be unused and not connected to external power for more than 2 weeks, remove and store the battery pack. CAUTION: To prevent damage to a battery pack, do not expose it to high temperatures for an extended time. High temperatures accelerate the self-discharge rate of a stored battery pack. To prolong the charge of a stored battery pack, store it in a cool, dry place within the following temperature ranges.
Battery Packs Finding More Power Information For more information about using Standby and Hibernation, conserving power, setting power preferences, and using other power management features, refer on this CD to the Software Guide, “Power” chapter.
4 Hard Drive Caring for Drives Hard drives are fragile notebook components that must be handled with care. Read carefully the following general caution notices. Caution notices specific to individual procedures are provided throughout this chapter with the procedures to which they apply. CAUTION: To prevent loss of work or damage to the notebook or a drive: Handle the drive carefully. Do not drop the drive. Keep in mind that excessive force can damage drive connectors.
Hard Drive Airport security devices that check carry-on luggage placed on a conveyor belt use X-rays instead of magnetics and do not damage hard drives. Hard Drive Activity Light The hard drive activity light turns on when the hard drive is being accessed.
Hard Drive Replacing the Primary Hard Drive The hard drive in the hard drive bay is the primary hard drive. CAUTION: To prevent system lockup and loss of information: Shut down the notebook before removing the hard drive from the hard drive bay. Do not remove the hard drive while the notebook is on, in Standby, or in Hibernation. If you are not sure whether the notbook is in Hibernation, turn on the notebbok and then shutit down. To replace the primary hard drive: 1. Save your work. 2.
Hard Drive 5. Slide the bottom half of the front bezel upward to create a handle. Extending the front bezel to create a handle 6. Pull the drive out of the bay.
Hard Drive 7. Insert a hard drive by sliding the hard drive into the bay until the drive is seated. Inserting the hard drive into the hard drive bay 8. Close the front bezel of the hard drive.
Hard Drive 9. Reinsert the hard drive retaining screw. (If you removed but did not replace a hard drive, put the retaining screw in a safe place.
5 Audio and Video Using Audio Features The notebook includes the following audio components: Audio components Audio Components Item Component 1 2 3 Mute button Mutes system volume. Volume buttons (2) Adjust the system volume. Connects optional, powered stereo speakers, headphones, headset, or television audio.
Audio and Video Audio Components (Continued) Item Component Description 4 Microphone input jack Connects an optional monaural microphone. 5 6 Speaker Produces system sound. Microphone Inputs single-channel sound. Adjusting the Volume To adjust the volume, use any of the following controls: Notebook volume buttons Tomute or restore volume, press Quick Launch mute button. You can also mute or restore volume by pressing the volume – and volume + buttons simultaneously.
Audio and Video Using the Microphone Input Jack When an external microphone is connected to the notebook, the notebook microphone is disabled. When connecting a microphone to the microphone input jack, use a monaural microphone with a 3.5-mm plug. Using the Audio Line-Out Jack WARNING: To reduce the risk of personal injury, adjust the volume before putting on headphones or a headset.
Audio and Video To transmit video signals through the S-Video out jack, you need an S-Video cable available from most electronic retailers. If you are combining audio and video functions, such as playing a movie from a DVD in an optional MultiBay drive to a television, you also need a standard audio cable available from most electronics retailers. Connecting a Device to the S-Video Out Jack To connect a video device to the S-Video out jack: 1.
Audio and Video Changing the Video Mode The default color television standard mode of the notebook is NTSC. Color television standard modes vary even within regions. However, NTSC is common in North America; PAL is common in Europe, China, Africa, and the Middle East; NTSC-J is common in Japan; and PAL-M is common in Brazil. Other South and Central American regions may use NTSC, PAL, or PAL-M. To change the color television standard mode from NTSC: 1.
6 Communication Devices Connecting a Modem Cable A modem cable, which has a 6-pin RJ-11 connector at each end, must be connected to an analog telephone line. Jacks for digital PBX systems may resemble analog telephone jacks, but are not compatible with the modem. WARNING: Connecting the notebook to a digital line can permanently damage the modem. Immediately disconnect your modem cable if accidentally connected to a digital line.
Communication Devices Using the RJ-11 Cable To connect an RJ-11 modem cable: 1. Plug the modem cable into the RJ-11 jack on the notebook 1. WARNING: To reduce the risk of electrical shock, fire, or damage to the equipment, do not plug a telephone cable into the RJ-45 network jack. 2. Plug the modem cable into the RJ-11 telephone jack 2.
Communication Devices Using a Country-Specific Adapter Cable Telephone jacks vary by country. To use the modem and the RJ11 cable outside the country in which you purchased the notebook, you must obtain a country-specific modem adapter. Refer on this CD to the Modem and Networking guide for more details about using your notebook internationally. To connect the modem to an analog telephone line that does not have an RJ-11 telephone jack: 1. Plug the modem cable into the RJ-11 jack on the notebook 1.
Communication Devices Connecting a Network Cable A network cable has an 8-pin RJ-45 connector at each end. If the network cable contains noise suppression circuitry, which prevents interference from TV and radio reception, orient the circuitry end of the cable toward the notebook.
Communication Devices To connect the network cable: 1. Plug the network cable into the RJ-45 jack on the notebook 1. 2. Plug the other end of the cable into a network jack 2. Connecting a network cable 3. Start or restart the notebook. 4. Connect to the network. Linking to an Infrared Device The notebook is IrDA-compliant—4 megabits per second (Mbps) standard—and can communicate with another infraredequipped device that is also IrDA-compliant.
Communication Devices Infrared signals are sent through an invisible beam of infrared light and require an unobstructed line of sight path. Linking to an infrared device The infrared port supports both low-speed connections of up to 115 kilobits per second (Kbps) and high-speed connections of up to 4 Mbps. Infrared performance may vary depending on the performance of infrared peripherals, distance between infrared devices, and applications used.
Communication Devices Sheild ports from direct sunlight, flashing incandescent light, and energy-saving fluorescent light. Be sure that no signals from remote control or other wireless devices, such as headphones or audio devices, aim at a port. During the transmission, do not move either device and do not allow objects or movement to disrupt the beam. Using Standby with Infrared Standby is not compatible with infrared transmission.
7 External Devices The jacks and connectors described in this guide support standard external devices. For information about which jack or connector to use, refer to the documentation included with the device. For information about installing or loading any software, such as drivers, required by the device, refer to the documentation included with the device. To connect a standard external device to the notebook: 1. Turn off the notebook. 2. If you are connecting a powered device, turn off the device. 3.
External Devices Connecting a Monitor or Projector To connect an external monitor or projector to the notebook, insert the monitor cable into the external monitor connector on the back of the notebook. If a properly connected external monitor or projector does not display an image, try pressing the Fn+F4 hotkeys to switch the image to the monitor.
External Devices USB hubs can be connected to a USB connector on the notebook or on an optional Port Replicator, or to other USB devices. Hubs support varying numbers of USB devices and are used to increase the number of USB devices in the system. Powered hubs must be connected to external power. Unpowered hubs must be connected either to a USB connector on the notebook or to a port on a powered hub.
External Devices 4. Select Enable USB legacy support. 5. To save your preference and exit Computer Setup, select File > Save Changes and Exit, then follow the instructions on the screen. Using an Optional External MultiBay An external MultiBay connects to the notebook by way of the self-powered USB connector and enables you to use MultiBay drives. For more information about the external MultiBay, refer to the documentation that is included with the device.
External Devices Connecting an Optional Cable Lock To install a security cable: 1. Loop the security cable around a secured object. 2. Pull the security cable lock through the cable loop and insert the cable 1 into the security cable slot on the notebook. 3. If the cable has a key 2, use it to lock and unlock the cable.
8 Hardware Upgrades To order hardware or learn more about upgrades and accessories, visit the HP Web site at http://www.hp.com or contact an authorized dealer, reseller, or service provider. For information about obtaining and installing software updates and upgrades, refer on this CD to the Software Guide, “Software Updates and Restorations” chapter.
Hardware Upgrades Inserting a PC Card CAUTION: To prevent damage to the connectors: Use minimal pressure when inserting a PC Card into a PC Card slot. Do not move or transport the notebook while a PC Card is inserted. To insert a PC Card: 1. Hold the PC Card label-side up with the connector facing the notebook. 2. Gently push the card into the slot until the card is seated.
Hardware Upgrades To remove a PC Card: 1. Stop the PC Card: In Windows 2000, select the Safety Remove Hardware icon in the taskbar, then stop the card you plan to remove. (When the card can be safely removed, a message is displayed.) In Windows XP, select the Safety Remove Hardware icon in the taskbar, then select the PC Card. (To display the Safely Remove Hardware icon, select Show Hidden Icons in the taskbar.) 2. Press the PC Card eject button 1. 3. Gently pull out the card 2.
Hardware Upgrades Using SD Cards Secure Digital (SD) cards are removeable postage stamp-sized compact flash storage devices that provide a convenient method of storing data and sharing it with other devices such as PDAs, cameras, and other SD equipped PCs. Inserting an SD Card CAUTION: To prevent damage to the connectors: Use minimal pressure when inserting an SD card into an SD card slot. Do not move or transport the notebook while an SD card is inserted, To insert an SD card: 1.
Hardware Upgrades Removing an SD Card CAUTION: To prevent loss of work or system lockup, stop the SD card before removing it. To remove an SD card:{xe "SD (Secure Digital) card:removing"} 1. Close all files and applications using the SD card. 2. Stop the SD card. In Windows 2000, select the Unplug or Eject icon in the task bar, then stop the card you plan to remove. (When the card can be safely removed, a message is displayed.
Hardware Upgrades Adding and Upgrading Memory Modules WARNING: The memory compartments are the only useraccessible internal compartments on the notebook. All other areas that require a tool to access should be opened only by an authorized service provider. WARNING: Failure to unplug the power cord and remove all battery packs before installing a memory expansion board can damage the equipment and expose you to the risk of electrical shock.
Hardware Upgrades 4. Turn the notebook bottom-side up. 5. Remove any battery packs from the notebook. 6. Remove the screw from the memory expansion slot cover 1. 7. Tilt the expansion slot cover away from the notebook 2. Removing the expansion slot cover 8. Remove the memory expansion slot cover.
Hardware Upgrades 9. Insert the memory expansion module: a. Align the keyed (notched) edge of the module with the keyed area in the expansion slot 1. b. Press the module into the slot from a 45-degree angle until it is seated, then push the board downward until the retention clips snap into place 2.
Hardware Upgrades 10. Insert the tabs on the expansion slot cover into the recesses in the expansion slot 1. 11. Replace the expansion slot cover over the expansion module compartment. 12. Replace the expansion slot cover screw 2. 13. Replace the battery packs. 14. Reconnect AC power and external devices. 15. Restart the notebook. Upgrading the Memory Module in the Primary Memory Slot To upgrade the memory module in the primary memory slot: 1. Shut down the notebook.
Hardware Upgrades 3. Disconnect the power cord. 4. Remove any battery packs from the notebook. 5. Remove the 3 keyboard screws from the bottom of the notebook. A keyboard icon is located next to the keyboard screws.
Hardware Upgrades 6. Using a fingernail or small flat tool, remove the Quick Launch button bezel located above the keyboard. Removing the Quick Launch button bezel 7. Remove the keyboard.
Hardware Upgrades 8. Remove the existing memory module: a. Pull away the retention clips on each side of the module 1. (The module tilts upward.) b. Lift the edge of the memory expansion module, then gently pull it out of the slot 2.{xe "slots:memory"} Removing the existing memory module To protect a memory module after it has been removed, place it in an static-safe container.
Hardware Upgrades 9. Insert the new memory module: a. Align the keyed (notched) edge of the module with the keyed area in the expansion slot 1. b. Press the module into the slot from a 45-degree angle until it is seated, then push the module downward until the retention clips snap into place 2. Inserting the new memory module 10. Replace the keyboard. 11. Replace the Quick Launch button bezel. 12. Replace the keyboard screws located on the bottom of the notebook. 13. Replace the battery packs. 14.
Hardware Upgrades Increasing RAM You can increase the random access memory (RAM) of the notebook with optional memory expansion modules. When RAM increases, the operating system increases the hard drive space reserved for the hibernation file. If you experience problems with Hibernation after increasing RAM, verify that your hard drive has enough free space for the larger hibernation file.
9 Specifications Notebook Dimensions Dimension Metric U.S. Height 2.79 cm 1.1 inches Width 27.94 cm 11 inches Depth 23.37 cm 9.2 inches Operating Environment Factor Metric U.S.
Specifications Rated Input Power Input Power Rating Operating voltage 100120/220240 VAC RMS Operating current 1.6/0.8 A RMS Operating frequency range 5060 Hz AC When powered by a DC source 18.5V MAX This product is designed for IT power systems in Norway with phase-to-phase voltage not exceeding 240 Vrms.
Index A adapter, modem 6–3 Aircraft Power Adapter (optional) 1–9, 3–11, 3–17 analog vs.
Index buttons mute 2–10, 5–1 PC Card eject 1–5, 8–3 pointing stick 1–1, 2–1 power 1–3 Presentation Mode 2–10 Quick Launch 1–3, 2–10 Quick Lock 2–10 TouchPad 1–2, 2–1 volume control 5–1 wireless on/off 2–10 C cable lock connecting 7–5 slot 1–6 cables modem 6–1, 6–2 network 6–4 security 1–6, 7–5 calibration, battery pack 3–17 cap, replacing pointing stick 2–3 caps lock light 1–12 charge sequence 3–10 compartments expansion memory 1–11 mini PCI (peripheral component interconnect) 1–10 primary memory 1–4 Ind
Index E embedded numeric keypad 2–12 enabling internal keypad 2–12 num lock mode 2–13 environmental specifications 9–1 exhaust vent 1–6 external devices (optional) 7–1 external keypad (optional) 2–12 external monitor connector 1–8 external mouse (optional) 2–4 External MultiBay connector 1–8 F Fn key 1–4, 2–5, 2–9, 2–11 function keys 1–4, 2–5 H hard drive activity light 1–12, 4–2 bay 1–6 caring for 4–1 inserting 4–5 removing 4–3 replacing 4–3 retaining screw 4–3, 4–6 Hardware Guide headphones 5–3 Hiber
Index J jack(s) audio line-out 1–5, 5–1, 5–3 microphone input 1–5, 5–2, 5–3 RJ-11 1–9, 6–1 RJ-45 1–9 S-Video out 5–3 K key(s) application 1–4 Fn 1–4, 2–5, 2–9, 2–12 function 1–4, 2–9 hotkeys 2–5, 2–9 internal keyboard 2–12 Microsoft logo 1–4 num lk 2–12 shortcut 2–5, 2–9 keyboard external (optional) 2–9 USB 7–3 keypads enabling/disabling 2–12 external (optional) 2–12 internal 2–11 L LAN, wireless 6–7 latches battery release 1–11 display release 1–7 Index-4 light battery 1–13, 3–11 caps lock 1–12 hard d
Index modem cable 6–1, 6–2 country-specific adapter 6–3 jack 1–9 Modem and Networking guide 6–2 Modem Command Guidelines (Advanced Users Only) 6–2 monitor, external (optional) connecting 7–1 connector 1–8 mouse, external 2–4 MultiBay, external (optional) 7–4 mute button 5–1 N network cable 6–4, 6–5 jack 1–9 noise suppression circuitry 6–1, 6–4 NTSC color television format 5–5 num lock key 2–12 light 1–12, 2–12 numeric keypad 2–12 O operating current 9–2 Hardware Guide operating environment specificatio
Index Port Replicator (optional) charging a battery pack with 3–11 docking connecter 1–10 external device connections 2–4 using the travel battery with 3–11 port, infrared 1–5, 6–6 power button 1–3 power connector 1–9 power, rated input 9–2 power/Standby light 1–13 powered USB 1–8 presentation mode button 2–10 primary battery pack 3–2 projector (optional), connecting 7–1 Q Quick Check, battery 3–14 Quick Launch buttons 1–3, 2–10 R RAM (Random Access Memory) 8–14 rated input power 9–2 relative humidity 9–
Index S-Video connecting cable 5–4 jack 1–8, 5–4 switching display and image 2– 6, 2–7, 7–2 system information 2–6, 2–8 T telephone (RJ-11) jack identifying 1–9 modem cable 6–1, 6–2 television (optional) changing color mode 5–5 connecting audio 5–4 connecting video 5–4 S-Video out jack 1–8, 5–4 switching image to or from 2–6, 2–7 temperature battery storage 3–20 operating 9–1 TouchPad buttons 1–2, 2–1 location 1–2, 2–1 using 2–3 travel battery attaching 3–7 charge sequence 3–10 connector 1–10, 3–7 detachi
Index W Windows applications key 1–4 wireless (802.
