Hardware Reference Guide HP Compaq Business Desktops dc7100 Small Form Factor Model Document Part Number: 359656-001 May 2004 This guide provides basic information for upgrading this computer model.
© Copyright 2004 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft, MS-DOS, Windows, and Windows NT are trademarks of Microsoft Corporation in the U.S. and other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Contents 1 Product Features Standard Configuration Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Working with the MultiBay Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Hot-Plugging” or “Hot-Swapping” MultiBay Drives . . . . . . . . . . . . . . . . . . . . . Uninstalling the MultiBay Security Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inserting a Drive into the MultiBay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing a Drive from the MultiBay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Product Features Standard Configuration Features The HP Compaq Small Form Factor features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the Diagnostics for Windows utility. Instructions for using this utility are provided in the Troubleshooting Guide on the Documentation CD. Small Form Factor computer can also be used in a minitower ✎ The configuration.
Product Features Front Panel Components Drive configuration may vary by model. Front Panel Components 1 Diskette Drive Activity Light 7 Microphone Connector 2 Diskette Drive 8 Headphone Jack 3 Optical Drive Activity Light 9 USB (Universal Serial Bus) Ports (2) 4 Diskette Eject Button - Hard Drive Activity Light 5 Optical Drive (CD-ROM, CD-R/RW, DVD-ROM, DVD+R/RW, or CD-RW/DVD Combo Drive) q Power On Light 6 Optical Drive Eject Button w Power Button 1-2 www.hp.
Product Features Rear Panel Components Rear Panel Components 1 Power Cord Connector 7 l Parallel Connector PS/2 Mouse Connector 8 c Monitor Connector 2 b 3 a PS/2 Keyboard Connector 9 h Headphone/Line-Out Connector 4 o Universal Serial Bus (USB) - j Line-In Audio Connector 5 m Serial Connector q g Microphone Connector 6 n RJ-45 Network Connector ✎ Arrangement and number of connectors may vary by model.
Product Features Keyboard Keyboard Components 1 Function Keys Perform special functions depending on the software application being used. 2 Editing Keys Includes the following: Insert, Home, Page Up, Delete, End, and Page Down. 3 Status Lights Indicate the status of the computer and keyboard settings (Num Lock, Caps Lock, and Scroll Lock). 4 Numeric Keys Work like a calculator keypad. 5 Arrow Keys Used to navigate through a document or Web site.
Product Features Windows Logo Key Use the Windows Logo key in combination with other keys to perform certain functions available in the Windows operating system. Refer to the “Keyboard” section to identify the Windows Logo key. Windows Logo Key Functions Windows Logo Key Displays or hides the Start menu. Windows Logo Key + d Displays the Desktop. Windows Logo Key + m Minimizes all open applications. Shift + Windows Logo Key + m Undoes Minimize All. Windows Logo Key + e Launches My Computer.
Product Features Serial Number Location Each computer has a unique serial number 1 located on the left side of the computer and a product ID number 2 located on the top cover of the computer. Keep these numbers available for use when contacting customer service for assistance. Serial Number and Product ID Locations 1-6 www.hp.
2 Hardware Upgrades Serviceability Features This computer includes features that make it easy to upgrade and service. No tools are needed for most of the installation procedures described in this chapter. Warnings and Cautions Before performing upgrades be sure to carefully read all of the applicable instructions, cautions, and warnings in this guide.
Hardware Upgrades Using the Small Form Factor Computer in a Minitower Configuration The Small Form Factor computer can be used in either a minitower or desktop configuration. To use it in the minitower configuration, stand the computer up on its right side as shown in the illustration below. at least 4 inches (10.2 cm) of space on all sides of the ✎ Ensure computer remains clear and free of obstructions.
Hardware Upgrades Unlocking the Smart Cover Lock Smart Cover Lock is an optional feature and is available on select ✎ The models only. The Smart Cover Lock is a software-controllable cover lock, controlled by the setup password. This lock prevents unauthorized access to the internal components. The computer ships with the Smart Cover Lock in the unlocked position. For more information about locking the Smart Cover Lock, refer to the Desktop Management Guide on the Documentation CD.
Hardware Upgrades To open the computer cover with the Smart Cover Lock engaged: 1. Turn off the computer properly through the operating system, then turn off any external devices. 2. Disconnect the power cord from the power outlet, and disconnect any external devices. 3. Use the FailSafe Key to remove the tamper-proof screw that secures the Smart Cover Lock. Removing the Smart Cover Lock Screw 4. Remove the computer cover. Refer to “Removing the Computer Cover.
Hardware Upgrades Removing the Computer Cover To remove the computer cover: 1. If you have locked the Smart Cover Lock, restart the computer and enter Computer Setup to unlock the lock. 2. Turn off the computer properly through the operating system, then turn off any external devices. 3. Disconnect the power cord from the power outlet and the computer, and disconnect any external devices.
Hardware Upgrades Replacing the Computer Cover To replace the computer cover, align the tabs on the panel with the slots on the chassis, then slide the cover all the way onto the chassis until it locks into place. Replacing the Computer Cover 2-6 www.hp.
Hardware Upgrades Installing Additional Memory The computer comes with double data rate synchronous dynamic random access memory (DDR-SDRAM) dual inline memory modules (DIMMs). DIMMs The memory sockets on the system board can be populated with up to four industry-standard DIMMs. These memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum memory support, you can populate the system board with up to 4GB of memory configured in a high-performing dual channel mode.
Hardware Upgrades The following processor bus frequencies are required for the system to run at the supported memory frequencies. Memory Frequency Required Processor Bus Frequency 333 MHz 533 MHz or 800 MHz 400 MHz 800 MHz If a memory frequency is paired with an unsupported processor bus frequency, the system will run at the highest supported memory speed. For example, if a 400 MHz DIMM is paired with a 533 MHz processor bus, the system will run at 400 MHz, the highest supported memory speed.
Hardware Upgrades ■ In any mode, the maximum operational speed is determined by the slowest DIMM in the system. For example, if the system is populated with a DIMM that is 333 MHz and a second DIMM that is 400 MHz, the system will run at the slower of the two speeds. There are four DIMM sockets on the system board, with two sockets per channel. The sockets are labeled XMM1, XMM2, XMM3, and XMM4. Sockets XMM1 and XMM2 operate in memory channel A. Sockets XMM3 and XMM4 operate in memory channel B.
Hardware Upgrades Installing DDR-SDRAM DIMMs Ä CAUTION: The memory module sockets have gold metal contacts. When upgrading the memory, it is important to use memory modules with gold metal contacts to prevent corrosion and/or oxidation resulting from having incompatible metals in contact with each other. Ä CAUTION: Static electricity can damage the electronic components of the computer or optional cards.
Hardware Upgrades 6. Open both latches of the memory module socket 1, then insert the memory module into the socket 2. Installing a DIMM module can be installed in only one way. Match the notch ✎ Aonmemory the module with the tab on the memory socket. maximum performance, populate the sockets so that the memory ✎ For capacity of Channel A is equal to the memory capacity of Channel B.
Hardware Upgrades 8. Repeat steps 6 and 7 for any additional modules that you want to install. 9. Replace the computer cover. 10. If you normally lock the Smart Cover Lock, use Computer Setup to relock the lock and enable the Smart Cover Sensor. The computer automatically recognizes the additional memory the next time you power on the computer. 2-12 www.hp.
Hardware Upgrades Installing an Expansion Card The computer has two standard PCI expansion slots that can accommodate an expansion card up to 17.46 cm (6.875 inches) in length. The computer also has one PCI Express x1 expansion slot and one PCI Express x16 expansion slot. PCI and PCI Express slots support only low profile cards unless ✎ The an optional riser is installed. The optional riser supports two full height standard PCI slots.
Hardware Upgrades To install an expansion card: 1. If you have locked the Smart Cover Lock, restart the computer and enter Computer Setup to unlock the lock. 2. Turn off the computer properly through the operating system, then turn off any external devices. 3. Disconnect the power cord from the power outlet and disconnect any external devices. 4. Remove the computer cover. Refer to “Removing the Computer Cover.” 5. Identify the slot into which you want to insert the expansion card. 6.
Hardware Upgrades 8. Install the expansion card by sliding the card under the slot cover retention latch then pressing the card down into the slot on the system board. sure not to scrape other components in the chassis when installing ✎ Be an expansion card. Installing an Expansion Card 9. Rotate the slot cover retention latch back in place to secure the expansion card.
Hardware Upgrades Removing a PCI Express Expansion Card To remove a PCI Express expansion card: 1. If you have locked the Smart Cover Lock, restart the computer and enter Computer Setup to unlock the lock. 2. Turn off the computer properly through the operating system, then turn off any external devices. 3. Disconnect the power cord from the power outlet and disconnect any external devices. 4. Remove the computer cover. Refer to “Removing the Computer Cover.” 5.
Hardware Upgrades 7. Store the card in anti-static packaging. 8. If you are not installing a new expansion card, install an expansion slot cover to close the open slot. 9. Rotate the slot cover retention latch back in place to secure the expansion cards and expansion slot covers. Ä Hardware Reference Guide CAUTION: All expansion card slots on the rear of the computer must contain either an expansion card or slot cover for proper cooling of internal components during operation. www.hp.
Hardware Upgrades Installing Additional Drives The computer has two external drive bays. When installing additional drives, follow these guidelines: ■ The primary Serial ATA (SATA) hard drive should be connected to the primary SATA controller on the system board (labeled P60 SATA 0). Connect a second SATA hard drive to the secondary SATA controller on the system board (labeled P61 SATA 1).
Hardware Upgrades Locating Drive Positions Drive Positions 1 3.5-inch, internal, standard hard drive bay 2 5.25-inch drive bay for optional drives 3 3.5-inch drive bay (1.44-MB diskette drive shown)* *If the computer has a 1.44-MB diskette drive installed, it will be configured with a diskette drive bezel (PN 360189-001) as shown in the illustration. If the computer contains an empty 3.5-inch drive bay, then a bezel blank (PN 358797-001) will be installed on the computer instead.
Hardware Upgrades Removing an Optical Drive Ä CAUTION: All removable media should be taken out of the drives before removing the drive from the computer. optical drive is a CD-ROM, CD-R/RW, DVD-ROM, ✎ An DVD+R/RW, or CD-RW/DVD Combo drive. To remove an optical drive: 1. If you have locked the Smart Cover Lock, restart the computer and enter Computer Setup to unlock the lock. 2. Turn off the computer properly through the operating system, then turn off any external devices. 3.
Hardware Upgrades 5. Press down on the green latch located on the front of the chassis next to the drives 1. This disengages the drive cage. 6. Slide the drive cage forward until it stops 2. This unlocks the drive. Disengaging the Drive Cage Hardware Reference Guide www.hp.
Hardware Upgrades 7. Disconnect the power and data cables from the rear of the optical drive. Disconnecting the Power and Data Cables 8. Slide the optical drive forward and lift it up and out of the drive cage. Removing the Optical Drive 2-22 www.hp.
Hardware Upgrades replace the optical drive, reverse the removal procedure. When ✎ Toreplacing a drive, transfer the four guide screws from the old drive to the new one. The screws take the place of drive rails. Removing a Diskette Drive Ä CAUTION: All removable media should be taken out of the drives before removing the drive from the computer. The diskette drive is located underneath the optical drive. To remove the diskette drive: 1.
Hardware Upgrades Installing an Optional Optical Drive To install an optional optical drive: 1. If you have locked the Smart Cover Lock, restart the computer and enter Computer Setup to unlock the lock. 2. Turn off the computer properly through the operating system, then turn off any external devices. 3. Disconnect the power cord from the power outlet and disconnect any external devices. 4. Remove the computer cover. Refer to “Removing the Computer Cover.” 5.
Hardware Upgrades 6. Press down on the green latch located on the front of the chassis next to the drives 1. This disengages the drive cage. 7. Slide the drive cage forward until it stops 2. This unlocks the drive. Disengaging the Drive Cage Hardware Reference Guide www.hp.
Hardware Upgrades 8. Position the guide screws on the drive into the J-slots in the drive bay 1. Then, slide the drive toward the rear of the computer 2 to secure the drive in the J slots. Installing the Optical Drive 2-26 www.hp.
Hardware Upgrades 9. Connect the data cable to the system board. 10. Connect the power and data cables to the rear of the optical drive. Connecting the Power and Data Cables 11. Slide the drive and drive cage all the way back into the chassis until the drive cage locks into position. drive automatically locks in the drive cage when the drive cage is ✎ The slid back. 12. Replace the computer cover. The system automatically recognizes the drive and reconfigures the computer.
Hardware Upgrades Upgrading the SATA Hard Drive Removing and Replacing the Hard Drive sure to back up the data on the old hard drive before removing ✎ Make it so that you can install the data onto the new hard drive. The preinstalled 3.5-inch hard drive is located under the power supply. To remove and replace the hard drive: 1. If you have locked the Smart Cover Lock, restart the computer and enter Computer Setup to unlock the lock. 2.
Hardware Upgrades 5. Press down on the green latch located on the front of the chassis next to the optical drive 1 and slide the optical drive cage forward 2. Sliding the Optical Drive Forward Hardware Reference Guide www.hp.
Hardware Upgrades 6. Rotate the power supply cage to the upright position. Raising the Power Supply Cage 7. Disconnect the power cable 1 and data cable 2 from the back of the hard drive. Disconnecting the Hard Drive Power Cable and Data Cable 2-30 www.hp.
Hardware Upgrades 8. Pull the tab that locks the drive in place away from the drive 1, slide the hard drive toward the front of the computer, then lift the drive up and out of the bay 2. Removing the Hard Drive 9. To install a hard drive, reverse the above procedure. replacement hard drive kit includes several data cables. Make ✎ The sure to use the cable that is exactly the same as the factory-installed cable.
Hardware Upgrades replacing the hard drive, transfer the four screws from the old ✎ When drive to the new one. The screws take the place of drive rails. You will need a Torx T-15 screwdriver to remove and re-install the guide screws. HP has provided four extra 6-32 standard guide screws on the front of the chassis, under the computer cover. The 6-32 standard guide screws are silver.
Hardware Upgrades The 3.5-inch bay is located underneath the optical drive. To install a drive into the 3.5-inch bay: guide screws to ensure the drive will line up correctly in the ✎ Install drive cage and lock in place. HP has provided extra guide screws (four 6-32 standard screws and four M3 metric screws), installed in the front of the chassis, under the computer cover. The hard drive uses 6-32 standard screws. All other drives use M3 metric screws.
Hardware Upgrades 4. Connect the power and data cables to the rear of the drive. If installing a second hard drive, connect the other end of the data cable to the system board connector labeled P61 SATA 1. 5. Remove the drive bezel by pushing the two tabs on one side of the larger front bezel inward 1 and rotating the drive bezel away from the larger front bezel 2. ✎ The type of bezel will vary depending on the computer configuration. Removing a Drive Bezel (Diskette Drive Bezel shown) 2-34 www.hp.
Hardware Upgrades 6. Replace the removed drive bezel with the appropriate bezel by pushing the bezel into place. type of bezel you need will depend on the type of device you are ✎ The installing. If you are installing a diskette drive, you must install a diskette drive bezel (PN 360189-001). If you are installing a hard drive, you must install a bezel blank (PN 358797-001) as shown in the illustration below. If you are installing a 3.
Hardware Upgrades Working with the MultiBay Option The MultiBay option is a special drive bay that supports a variety of optional 12.7-mm removable drives, including: ■ MultiBay CD-ROM Drive* ■ MultiBay CD-RW Drive ■ MultiBay DVD-ROM Drive ■ MultiBay CD-RW/DVD-ROM Combo Drive ■ MultiBay SMART Hard Drive * Can be hot-plugged or hot-swapped installation procedure for installing the MultiBay option is the ✎ The same as described for installing an optical drive.
Hardware Upgrades “Hot-Plugging” or “Hot-Swapping” MultiBay Drives Ä CAUTION: To prevent damage to the computer, the drive, and any data stored on the drive: Before inserting or removing a hard drive, shut down the computer. Never remove a hard drive while the computer is on or on standby. To ensure that the computer is not on standby, turn the computer on, then shut it down.
Hardware Upgrades Uninstalling the MultiBay Security Screw When installed, the MultiBay security screw disables the MultiBay eject lever, so that a drive installed in the MultiBay cannot be removed. To remove a drive installed in the MultiBay, you must first remove the security screw, if installed, using the FailSafe Key. a FailSafe Key was not provided with the computer, contact an ✎ Ifauthorized HP reseller or service provider.
Hardware Upgrades Inserting a Drive into the MultiBay 1. Remove any removable media, such as a compact disc, from the drive. 2. If you are not hot-swapping a CD-ROM drive, exit all software applications, shut down the operating system software, and turn off the computer. 3. With the top of the drive facing up and the drive connector facing the computer, slide the drive into the MultiBay and push firmly to ensure that the electrical connector is properly seated. Inserting a Drive into the MultiBay 4.
Hardware Upgrades Removing a Drive from the MultiBay 1. Remove any removable media, such as a compact disc, from the drive. 2. Before removing an optical drive, stop the drive using the Safely Remove Hardware icon on the Windows task bar. 3. If you are not hot-swapping a CD-ROM drive, exit all software applications, shut down the operating system software, and turn off the computer. 4. Remove the MultiBay security screw, if it has been installed.
Hardware Upgrades Partitioning and Formatting a MultiBay Hard Drive must be logged on as an Administrator or a member of the ✎ You Administrators group in order to complete this procedure. 1. Exit all software applications, shut down the operating system software, and turn off the computer. 2. Insert the MultiBay hard drive into the MultiBay. Refer to “Inserting a Drive into the MultiBay” for more information. 3. Turn on the computer. 4. Click Start. 5. Right-click My Computer, then click Manage. 6.
A Specifications Ensure at least 4 inches (10.2 cm) of space on all sides remains clear and free of obstructions. HP Compaq Small Form Factor Desktop Dimensions Height 3.95 inches 10.3 cm Width 13.3 inches 33.78 cm Depth (depth will increase if the computer is equipped with a port security bracket) 14.9 inches 37.85 cm 21 lb 9.53 kg Operating 50° to 95° F 10° to 35° C Nonoperating -22° to 140° F -30° to 60° C Operating 10–90% 10–90% Nonoperating (38.
Specifications HP Compaq Small Form Factor (Continued) Power Supply Operating Voltage Range* 90–264 VAC 90–264 VAC Rated Voltage Range 100–240 VAC 100–240 VAC Rated Line Frequency 50–60 Hz 50–60 Hz Power Output 240 W 240 W Rated Input Current (maximum)* 5A @ 100 VAC 2.5A @ 200 VAC Maximum 1260 BTU/hr 318 kg-cal/hr Typical (idle) 340 BTU/hr 86 kg-cal/hr Heat Dissipation *This system utilizes an active power factor corrected power supply.
B Battery Replacement The battery that comes with the computer provides power to the real-time clock. When replacing the battery, use a battery equivalent to the battery originally installed in the computer. The computer comes with a 3-volt lithium coin cell battery. lifetime of the lithium battery can be extended by plugging the ✎ The computer into a live AC wall socket. The lithium battery is only used when the computer is NOT connected to AC power.
Battery Replacement Ä CAUTION: Static electricity can damage the electronic components of the computer or optional equipment. Before beginning these procedures, ensure that you are discharged of static electricity by briefly touching a grounded metal object. 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock and disable the Smart Cover Sensor. 2. Turn off the computer properly through the operating system, then turn off any external devices.
Battery Replacement Type 2 a. To release the battery from its holder, squeeze the metal clamp that extends above one edge of the battery. When the battery pops up, lift it out 1. b. To insert the new battery, slide one edge of the replacement battery under the holder’s lip with the positive side up. Push the other edge down until the clamp snaps over the other edge of the battery 2. Removing and Replacing a Coin Cell Battery (Type 2) Hardware Reference Guide www.hp.
Battery Replacement Type 3 a. Pull back on the clip 1 that is holding the battery in place, and remove the battery 2. b. Insert the new battery and position the clip back into place. Removing a Coin Cell Battery (Type 3) the battery has been replaced, use the following steps to ✎ After complete this procedure. 5. Replace the computer cover. 6. Plug in the computer and turn on power to the computer. 7. Reset the date and time, your passwords, and any special system setups, using Computer Setup.
C Security Lock Provisions Installing a Security Lock The security locks displayed below and on the following pages can be used to secure the computer. port security bracket (not shown) is also available. Go to ✎ Awww.hp.com for more information. Cable Lock If present, insert the cable lock in the location shown below. I Installing a Cable Lock Hardware Reference Guide www.hp.
Security Lock Provisions Padlock Installing a Padlock C-2 www.hp.
Security Lock Provisions Universal Chassis Clamp Lock Without Security Cable 1. Thread the keyboard and mouse cables through the lock. Hardware Reference Guide www.hp.
Security Lock Provisions 2. Screw the lock to the chassis using the screw provided. 3. Insert the plug into the lock 1 and push the button in 2 to engage the lock. Use the key provided to disengage the lock. C-4 www.hp.
Security Lock Provisions With Security Cable 1. Fasten the security cable by looping it around a stationary object. 2. Thread the keyboard and mouse cables through the lock. Hardware Reference Guide www.hp.
Security Lock Provisions 3. Screw the lock to the chassis using the screw provided. 4. Insert the plug end of the security cable into the lock 1 and push the button in 2 to engage the lock. Use the key provided to disengage the lock. C-6 www.hp.
D Electrostatic Discharge A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. Preventing Electrostatic Damage To prevent electrostatic damage, observe the following precautions: ■ Avoid hand contact by transporting and storing products in static-safe containers. ■ Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
Electrostatic Discharge ■ Use heelstraps, toestraps, or bootstraps at standing workstations. Wear the straps on both feet when standing on conductive floors or dissipating floor mats. ■ Use conductive field service tools. ■ Use a portable field service kit with a folding static-dissipating work mat. If you do not have any of the suggested equipment for proper grounding, contact an HP authorized dealer, reseller, or service provider.
E Routine Computer Care and Shipping Preparation Routine Computer Care Follow these suggestions to take care of the computer and monitor: Hardware Reference Guide ■ Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance at the back of the system unit and above the monitor to permit the required airflow. ■ Never operate the computer with the cover or side panel removed. ■ Never restrict the airflow into the computer by blocking the front vents or air intake.
Routine Computer Care and Shipping Preparation Optical Drive Precautions Be sure to observe the following guidelines while operating or cleaning the optical drive. Operation ■ Do not move the drive during operation. This may cause it to malfunction during reading. ■ Avoid exposing the drive to sudden changes in temperature, as condensation may form inside the unit. If the temperature suddenly changes while the drive is on, wait at least one hour before you turn off the power.
Routine Computer Care and Shipping Preparation Shipping Preparation Follow these suggestions when preparing to ship the computer: 1. Back up the hard drive files on PD discs, tape cartridges, CDs, or diskettes. Be sure that the backup media is not exposed to electrical or magnetic impulses while stored or in transit. hard drive locks automatically when the system power is ✎ The turned off. 2. Remove and store any program diskettes from the diskette drives. 3.
Index A application key 1–4 audio connectors 1–2, 1–3 B battery replacement B–1 bezel installing 2–35 part numbers 2–19, 2–32, 2–35 removing 2–34 C cable lock, installing C–1 chassis clamp lock, installing C–3 components front panel 1–2 rear panel 1–3 computer care guidelines E–1 computer cover removing 2–5 replacing 2–6 Smart Cover Lock 2–3 computer specifications A–1 D desktop dimensions A–1 DIMMs See memory diskette drive activity light 1–2 eject button 1–2 removing 2–20 Hardware Reference Guide dri
Index H M hard drive activity light 1–2 installing in 3.
Index installing 2–24 location 1–2 precautions E–2 removing 2–20 P padlock, installing C–2 Parallel ATA devices 2–18 parallel connector 1–3 partitioning hard drive, MultiBay 2–41 PCI card See expansion card power button 1–2 cord connector 1–3 indicator light 1–2 power supply 2–30, A–2 R rear panel components 1–3 removing bezel 2–34 computer cover 2–5 diskette drive 2–20 expansion slot cover 2–14 hard drive 2–31 MultiBay drive 2–40 optical drive 2–20 PCI Express expansion card 2–16 Smart Cover Lock 2–4 RJ
