HP Notebook PC Reference Guide
Notice This manual and any examples contained herein are provided “as is” and are subject to change without notice. Hewlett-Packard Company makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard Co. shall not be liable for any errors or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual or the examples herein.
Important Safety Information CAUTION To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord to connect a modem to the telephone wall jack. In Australia, the computer must be connected to the Telecommunication Network through a line cord that meets the requirements of ACA Technical Standard TS008.
For a PC supplied with a Microsoft operating system: When you start the PC and accept the Microsoft End-user License Agreement (“EULA”), your license rights are valid only if a Certificate of Authenticity (“COA”) label corresponding to your Microsoft operating system is provided with your PC. The COA label can usually be found on the bottom of the computer. If the COA label does not correspond to your Microsoft operating system or is missing, contact your HP reseller for details.
EXPORT CLAUSE. Customer agrees not to export or re-export the software or any copy or adaptation in violation of the U.S. Export Administration regulations or other applicable regulation. U.S. GOVERNMENT RESTRICTED RIGHTS. Use, duplication, or disclosure is subject to HP standard commercial license terms and for non-DOD Departments and Agencies of the U.S. Government, the restrictions set forth in FAR 52.227-19(c)(1-2) (June 1987) Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304 U.S.A.
Contents Getting Started with Your HP Notebook ..................................................................... 11 Taking Inventory......................................................................................................... 12 What’s in the box? ................................................................................................ 12 To buy accessories ................................................................................................ 12 To find more information....
To protect against viruses ..................................................................................... 41 To lock the hard disk drive.................................................................................... 41 Working in Comfort with a Notebook PC .................................................................. 42 Taking Care of Your Computer .................................................................................. 44 To protect your hard disk drive...........................
Connecting External Devices...................................................................................... 78 To identify connectors for external devices .......................................................... 78 To connect a printer or other parallel device......................................................... 80 To connect an external keyboard or mouse........................................................... 80 To connect a USB device.........................................................
To update the BIOS............................................................................................. 123 To update Windows drivers ................................................................................ 124 HP Support and Service............................................................................................... 125 Getting Assistance for Your Computer..................................................................... 126 To get help from the Web ...........................
Getting Started with Your HP Notebook Reference Guide 11
Getting Started with Your HP Notebook Taking Inventory Taking Inventory Congratulations! Your notebook computer sets a new standard in personal computing. Although compact and easy to carry, your computer is made with the quality and attention to detail that are the hallmark of Hewlett-Packard. This manual shows how to set up and operate your computer, as well as what to do if you run into trouble. What’s in the box? • HP notebook PC. • Battery (installed). • AC adapter and power cord.
Getting Started with Your HP Notebook Taking Inventory • RAM modules for expanding memory. • Battery. • Port replicator. To find more information The following table lists other sources of information about your computer and related products. Source Description and Location Startup Guide This printed manual introduces your computer. It also contains setup instructions, basic operation guidelines, troubleshooting information, and warranty information.
Getting Started with Your HP Notebook Identifying Parts of the Computer Identifying Parts of the Computer Front View 1. Computer open/close latch. 7. Built-in microphone*. 2. One-Touch buttons. 8. Infrared port*. 3. Keyboard status lights. 9. Wireless on-off button and indicator light*. 4. Power button. Turns the computer on and off. 10. Battery. 5. Touch pad, scroll pad, click buttons, plus on-off button. 11. CD-ROM, DVD, or other drive. 6.
Getting Started with Your HP Notebook Identifying Parts of the Computer Back View 13. AC adapter jack. 21. Modem port*. 14. Two universal serial bus ports (USB). 15. LAN port*. 22. PC Card and CardBus slot and button (certain models have two slots and two buttons). 16. S-video port*. 23. IEEE 1394 port*. 17. Parallel port (LPT1). Use this port for a parallel printer or other parallel device. 24. Audio jacks (left to right): external microphone, audio out (headphones). 18. Serial port (COM1).
Getting Started with Your HP Notebook Identifying Parts of the Computer Bottom View 28. Hard disk drive. 31. Reset button. 29. Battery latch. 32. Docking port*. 30. RAM cover. 33. Mini-PCI cover (no user parts inside).
Getting Started with Your HP Notebook Identifying Parts of the Computer Status Lights The computer includes a number of status lights that report power and battery status, drive activity, and keyboard functions such as Caps Lock and Num Lock. The following diagram shows the main status lights on the front of the computer. 1. Power mode. • On: the computer is on (even if the display is off). • Blinking: the computer is in Standby mode. • Off: the computer is off or in Hibernate mode. 2.
Getting Started with Your HP Notebook Identifying Parts of the Computer The keyboard status lights, located above the keyboard, indicate the states of the keyboard locks. 1. Caps Lock. Caps Lock is active. 2. Num Lock. Num Lock is active. (The Keypad Lock must also be on to use the embedded keypad.) 3. Keypad Lock. The embedded keypad is active (Fn+F8). Num Lock must also be on for the numeric keys—otherwise, cursor control is active (as marked on an external keyboard).
Getting Started with Your HP Notebook Setting Up Your Computer Setting Up Your Computer WARNING Improper use of keyboards and other input devices has been associated with ergonomic injury. For information about reducing your risk, see Working in Comfort in the online HP Library, or visit our ergonomics Web site, www.hp.com/ergo. For a summary about working with a notebook computer, see “Working in Comfort with a Notebook PC” on page 42.
Getting Started with Your HP Notebook Setting Up Your Computer To remove the battery 1. Before removing the battery, do one of the following: • Shut down the computer or put it into Hibernate mode, or • Plug in the AC adapter. 2. Slide the battery’s release latch, and then slide the battery out of its compartment.
Getting Started with Your HP Notebook Setting Up Your Computer Step 2: Connect AC power CAUTION Use only the HP AC adapter included with your computer (or other approved adapter that meets the power requirements of the computer). If “75W” is printed below the AC adapter socket on the computer, do not use a 60watt, 3.16-amp adapter, such as HP F1454A or F1781A, and do not use DC adapter accessories F1455A and F2297A.
Getting Started with Your HP Notebook Setting Up Your Computer Step 3: Connect a phone line If your computer does not include a built-in modem, you can skip this step. Also, if you prefer, you can instead connect to a PC Card modem or an external modem. 1. Make sure the telephone line is an analog line, sometimes called a data line. (You must not use a digital line.) 2. Connect the telephone cord into a telephone jack. If the plug on the phone cord doesn’t fit the jack, you may need to use an adapter. 3.
Getting Started with Your HP Notebook Setting Up Your Computer Step 4: Turn on the computer • Press the power button above the left side of the keyboard. The computer then boots up, and Windows starts automatically. Hint If your computer does not turn on when operating on battery power, the battery may be out of power. Plug in the AC adapter and press the power button again. Leave the AC adapter plugged in for at least an hour—or 2–3 hours to charge it fully.
Getting Started with Your HP Notebook Setting Up Your Computer Step 6: Register your notebook Be sure to register your computer. Registering is free and fast, and ensures you will receive quicker, more personalized support. The information you provide during registration allows us to provide you with better products and services. Registering your computer does the following: • Records your ownership of the computer with Hewlett-Packard and provides access to service, support, and information.
Basic Operation Reference Guide 25
Basic Operation Operating Your Computer Operating Your Computer You can start and stop your computer using its power button. However, at certain times you may want to use other methods to start or stop the computer—depending on power considerations, types of active connections, and start-up time. To turn the computer on and off Power mode To enter this mode On mode Power mode status light is on. Press the power button. Standby mode Saves significant power. Turns off the display and other components.
Basic Operation Operating Your Computer To reset the computer Occasionally, you may find that Windows or the computer has stopped responding, and will not let you turn the computer off. If this happens, try the following in the order listed. • If possible, shut down Windows: press CTRL+ALT+DEL, and then click Shut Down, Restart. –or, if this fails– • Press the power button for 4 seconds until the display shuts down, and then press the power button again to restart.
Basic Operation Operating Your Computer 3. Use the arrow keys to select the boot device, and press ENTER. If you want to boot from a specific device whenever it is present, change the boot order using the BIOS Setup utility—see “To run the BIOS Setup utility” on page 118. To use the touch pad The touch pad includes an on-off button so you can turn off the touch pad to avoid moving the pointer accidentally, such as by touching the pad while typing.
Basic Operation Operating Your Computer Moving and selecting 1. Place your hands in a normal typing position. 2. Move a thumb or finger across the touch pad in the direction you want the pointer to move. 3. Use the left and right click buttons, which function like the left and right buttons on a mouse, to make your selection: • To open an application, move the pointer over the icon and double-click the left button. • To make menu selections, move the pointer to the menu item and click the left button.
Basic Operation Operating Your Computer To use the Fn hot keys The combination of the Fn key plus another key creates a hot key—a shortcut key sequence—for various system controls. To use a hot key, press and hold Fn, press the appropriate second key, and then release both keys. This hot key Fn+F1 Does this Decreases the display brightness. Fn+F2 Increases the display brightness. Fn+F5 Toggles among the built-in display, an external display, and simultaneous display on both.
Basic Operation Operating Your Computer To use the One-Touch buttons Your computer includes five One-Touch buttons that can start any application or open a document or Web site with a single press. • Press the One-Touch button to open the corresponding application, document, or Web site. Your computer is preconfigured to access the following services: 1. Microsoft Outlook Express e-mail software. 2. HP TV Now—see “To use a TV set as a monitor” on page 83. 3. Microsoft Internet Explorer. 4.
Basic Operation Operating Your Computer 3. Type a label for the button, and then select the application, document, folder, or Web site you want the button to open. 4. If you want a label to appear onscreen when you press a One-Touch button, select that option on the Onscreen Display tab. To use the Windows and Applications keys The Windows key brings up the Windows Start menu. This is the same as clicking the Start button on the taskbar.
Basic Operation Operating Your Computer To use the embedded keypad Your computer’s built-in keyboard includes an embedded keypad you can use to type numbers and arithmetic operators. The keys in this keypad are marked using light blue characters. • Press Fn+F8 to turn on the embedded keypad. • Hold Fn while typing a key to turn the embedded keypad on temporarily.
Basic Operation Operating Your Computer To adjust the display Changing the brightness • Press Fn+F1 or Fn+F2 to decrease or increase (respectively) the display’s brightness. –or– • Click Start, All Programs, Hewlett-Packard, Notebook, HP Display Settings. You have the option of adding a display settings icon in the taskbar for quick access. Hint To maximize your battery operating time, set the brightness to the lowest level you can view comfortably.
Basic Operation Operating Your Computer To adjust the volume To increase or decrease the volume • Press Fn+PageUp or Fn+PageDown. • Press the back or front half of the volume control on the left side of the computer (certain models). • Click the speaker icon in the taskbar (if not present, see Windows Help), and drag the volume control bar up or down. To mute the audio You can mute the audio output without changing the volume setting.
Basic Operation Operating Your Computer 2. Select the presentation you want to show. If you don’t select one, you can choose one when you start the show. 3. If you want to change the video or power settings for the show, click Settings. To show the presentation • Click Start, All Programs, Hewlett-Packard, HP Presentation Ready, Start Presentation. –or– Click the HP Presentation Ready icon in the taskbar (if present), and then click Start Presentation.
Basic Operation Using CDs or DVDs Using CDs or DVDs To insert or remove a CD or DVD CAUTION Do not remove a CD or DVD while the computer is reading it. Otherwise, the computer could stop responding and you could lose data. Be sure to press the CD or DVD onto the spindle. You can damage the disk or drive if you just lay it on the tray. 1. Press the button on the face of the CD-ROM or DVD drive. If you are using this drive for the first time, be sure to remove the cardboard packing insert. 2.
Basic Operation Using CDs or DVDs To play DVD movies If your computer came with a DVD drive, it also includes DVD player software that lets you play DVD movies. • Click Start, All Programs, Multimedia, DVD Player, InterVideo WinDVD. You can also use Windows Media Player to play DVD movies. To play DVD movies on a TV, see “To use a TV set as a monitor” on page 83. Hint For best performance while playing movies on battery power, set the Control Panel power scheme to Portable/Laptop.
Basic Operation Securing Your Computer Securing Your Computer To set up password protection You can protect your computer from access by another user when you set up password protection, which is available through Windows and through the BIOS Setup utility. For complete protection, set passwords in Windows as well as through BIOS Setup. To cancel password protection, set an empty password. BIOS Setup Utility 1. Click Start, Turn Off Computer, Restart. 2.
Basic Operation Securing Your Computer • Press the HP Quick Lock button—the five One-Touch buttons are located above the keyboard. –or– • Press CTRL+ALT+DEL and click Lock Computer. This option may not be available in all configurations. To unlock the computer, follow your normal logon steps. To attach a security cable Your computer includes a built-in connector you can use to secure the computer with a cable and a lock (such as the Kensington MicroSaver lock system, available at many computer stores). 1.
Basic Operation Securing Your Computer To protect against viruses Virus-protection software can help protect the integrity of your data. This is especially important if you use the Web. Your computer comes equipped with Norton AntiVirus software. You can get detailed instructions from the software’s online Help. To lock the hard disk drive The computer enables you to lock its internal hard disk drive to help keep your information secure.
Basic Operation Working in Comfort with a Notebook PC Working in Comfort with a Notebook PC WARNING Improper use of keyboards and other input devices has been associated with ergonomic injury. For more information about reducing your risk, visit our ergonomics Web site at www.hp.com/ergo—or see Working in Comfort in the online HP Library. You can use your HP notebook computer virtually anywhere, anytime. The following recommendations should help you work more comfortably.
Basic Operation Working in Comfort with a Notebook PC Using Your Mobile Computer • Position the computer so your wrists and hands are in a neutral position. Your wrists should be as straight as possible and should not have to bend sideways or more than 10 degrees up or down. If your notebook computer does not have a built-in palm rest, you can use a rolled-up towel. • Try to type as lightly as possible. The notebook keyboard requires little force to activate.
Basic Operation Taking Care of Your Computer Taking Care of Your Computer Use the following recommendations to maintain your computer during everyday use and prevent potential physical damage or data loss. To protect your hard disk drive Hard disk drives, as well as other internal components, are not indestructible and can be damaged by inappropriate handling and operation. • Avoid bumps or jolts. • Do not operate the computer while traveling over bumpy terrain.
Basic Operation Taking Care of Your Computer To safeguard your data • Do not use a pointing device or activate any other device that interrupts operation while the system is starting or stopping. • Back up your work regularly. Copy files to floppy, CD-RW, or network drives. • Use a virus-scanning program (such as the Norton AntiVirus program included with your computer) to check the integrity of your files and operating system.
Basic Operation Taking Care of Your Computer To clean your computer • You can clean the computer with a soft cloth dampened with clean water or with water containing a mild detergent. Do not use an excessively wet cloth, and take care to keep water out of the case. • Do not use abrasive cleaners, especially on the display. Do not apply any cleaner directly to the display. Instead, apply the cleaner to a soft cloth and then gently wipe the display.
Batteries and Power Management Reference Guide 47
Batteries and Power Management Managing Power Consumption Managing Power Consumption When you’re running your computer on battery power, you will want to maximize operating time without compromising performance. Your computer is designed to help you reduce power consumption and extend battery life without needing to turn it off. • During idle periods, the computer automatically enters power-saving modes after specified timeout periods. You can adjust these timeouts to suit your working habits.
Batteries and Power Management Managing Power Consumption The computer can also enter Hibernate mode if battery power reaches a critically low level. (See “To respond to a low-battery warning” on page 52.) If this happens, you will find on resuming that all your data has been saved, but some functions may be disabled. To resume normal operation, restore power by connecting an AC adapter or installing a charged battery, and then shut the computer off and restart it.
Batteries and Power Management Managing Power Consumption To manage power manually In addition to allowing the computer to enter its power-saving modes automatically, you can also put it into any of the following three modes whenever you need to. Power mode Does this… Use when… To enter this mode… Standby Maintains your current session in RAM, and turns off the display and other components. You will be away from your computer for up to several hours.
Batteries and Power Management Using Battery Power Using Battery Power To check battery status From the battery status light You computer has a battery status light—see “Status Lights” on page 17. From the Windows taskbar The Windows taskbar can display a power icon that provides detailed battery status information (see Windows Help for details). The icon looks like a battery when AC is not connected. • Place the pointer over the power icon to display the remaining battery charge.
Batteries and Power Management Using Battery Power To respond to a low-battery warning The computer automatically alerts you when the battery power drops to a critically low level. The computer first emits a high-pitched beep or displays a warning message. Then, if you do not restore power within a short time, the computer goes into Hibernate mode.
Batteries and Power Management Using Battery Power • Put the computer in Standby mode whenever you are not using it for a short while: press the power button, or click Start, Turn Off Computer, Standby. • Put the computer in Hibernate mode whenever you want to save your current session, but will not be using the computer for a day or more: press Fn+F12. • Set the automatic timeout settings to emphasize saving power.
Modem and Network Connections Reference Guide 55
Modem and Network Connections Using the Modem Using the Modem If your computer has a modem port, you can connect your modem to a telephone line and communicate with other computers throughout the world. You can explore the Internet, send and receive e-mail messages, and use your PC to send and receive faxes.
Modem and Network Connections Using the Modem To connect the modem CAUTION To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord to connect the modem to the telephone wall jack. 1. Check that the telephone line is an analog line, sometimes called a data line. (You must not use a digital line.) 2. Connect a telephone cord with an RJ-11 plug into a telephone jack. If the plug on the phone cord doesn’t fit the jack, you may need to use an adapter. 3.
Modem and Network Connections Using the Modem failed connection, you must wait one hour before trying the number again. If you dial before the hour is up, you will get a message that says “black list.” • When using a modem in the Republic of South Africa, an external surge protector may be necessary in order to prevent computer damage by lightning or other electrical surges. Connect any approved surge protector to the modem cable whenever you are using the modem.
Modem and Network Connections Using the Modem To disconnect from the Internet You remain connected to the Internet until you shut down the computer, disconnect the phone line from the computer, or give a command to hang up the connection. • Click Start, Control Panel, Network and Internet Connections, Network Connections, and then right-click the connection and select Disconnect. –or– Double-click the connect icon in the taskbar, and click Disconnect.
Modem and Network Connections Using the Modem To change your modem settings The modem is already set up to be compatible with telephone systems and modems in most areas. However, in some situations, you may have to change modem settings to match local conditions. If you have questions about local requirements, contact your telephone company. • Control Panel. Open Phone and Modem Options in Control Panel to change many modem settings.
Modem and Network Connections Using the Modem To send and receive e-mail Sending and receiving e-mail requires an e-mail account with an Internet Service Provider or with your company’s communications system. If you are using AOL, e-mail services are part of your AOL service. For another ISP, you can use Outlook Express (included with your computer) or an e-mail system of your choice. This topic includes instructions for using Outlook Express. To start Outlook Express 1.
Modem and Network Connections Using the Modem To send and receive faxes Sending and receiving faxes requires just a telephone connection—you don’t need an Internet connection. You can use the modem and fax software to send and receive faxes on your computer. Fax Console fax software is included with Windows XP. To set up Fax Console Before you can use Fax Console, you need to install it. 1. Click Start, Control Panel, Add or Remove Programs. 2.
Modem and Network Connections Connecting to a LAN Connecting to a LAN If your model has a LAN port, you can connect to local area networks (LANs). LANs give you access to network resources, such as printers and file servers on your corporate network, and possibly to the Internet. To connect to a LAN 1. Check that the existing LAN supports Ethernet 10Base-T (10 Mbps) or 100Base-TX (100 Mbps) connections. 2. Plug the LAN cable (not supplied) into the built-in LAN port.
Modem and Network Connections Making Wireless Network Connections Making Wireless Network Connections If your computer includes a wireless on-off button—located on the right side of the front of the computer—you can connect by radio to an 802.11 wireless local area network (LAN) and access computers and other resources on the network. A wireless network provides all the functions of a typical “wired” network, but also provides for “roaming.
Modem and Network Connections Making Wireless Network Connections • Key format: ASCII for passphrase, hexadecimal for key string. • Key length: smaller number for 64-bit encryption, larger number for 128-bit. 6. Click OK to save the configuration. This network is added to your list of preferred networks. The computer automatically connects to the first preferred network that’s within range if wireless communication is turned on—see “To turn wireless communication on and off” on page 66.
Modem and Network Connections Making Wireless Network Connections To turn wireless communication on and off Important Wireless networks and cellular modems are examples of devices that use wireless communication. Such devices may be restricted in some situations or environments, such as when traveling in an airplane. If in doubt, be sure to ask for authorization before turning on your computer’s wireless networking.
Modem and Network Connections Making Wireless Network Connections If you’re within range of your wireless network, your computer automatically connects. To check the status of your wireless connection, open Network Connections in Control Panel and double-click the connection. Turning off communication and ending a connection 1. Important: close any files that reside on other network computers. 2. To turn off the wireless 802.
Modem and Network Connections Making Wireless Bluetooth Connections Making Wireless Bluetooth Connections If your computer includes Bluetooth wireless capabilities, you can use it to make shortrange radio connections to a wireless personal area network (PAN) and access other Bluetooth-compatible devices, such as other computers, cell phones, and printers.
Modem and Network Connections Making Wireless Bluetooth Connections Turning off Bluetooth communication Turning off communication ends any connection you have open. 1. Important: close any files that reside on other network computers. 2. To turn off Bluetooth communication without turning off your computer, press the wireless on-off button—this also turns off 802.11 communication if it was enabled.
Modem and Network Connections Making Wireless Bluetooth Connections To prepare for Bluetooth connections Before you use your computer to access other Bluetooth devices, you should configure some basic settings. 1. Make sure Bluetooth communication is turned on—see the previous topic. 2. Double-click the Bluetooth icon in the taskbar. 3. In the menu bar, click Bluetooth, Device Configuration. (This menu is available only while Bluetooth folders are selected.) 4.
Modem and Network Connections Making Wireless Bluetooth Connections To send or receive files using Bluetooth If your computer includes Bluetooth wireless capabilities, it supports the following common protocols for transferring data. To use either protocol, both computers must support that protocol—check the other computer’s Bluetooth documentation. • FTP, meaning files can be copied into and out of shared directories (folders) by both computers. This service is equivalent to common network file sharing.
Modem and Network Connections Making Wireless Bluetooth Connections To connect to a Bluetooth printer or serial device You can connect your computer to a Bluetooth serial device—for example, you could print from a word processor to a Bluetooth serial printer. 1. Make sure Bluetooth communication is turned on—see “To turn Bluetooth communication on and off” on page 68. 2. Install the printer software that comes with the Bluetooth printer. The following details are for the HP Deskjet 995C printer: a.
Modem and Network Connections Making Wireless Bluetooth Connections 12. Double-click the printer icon for the Bluetooth printer you want to use, then doubleclick the serial port icon that is shown. When you see a message confirming this printer will use the Bluetooth COM port, click OK. Whenever you print to this printer, it will use the Bluetooth connection you established.
Add-On Devices Reference Guide 75
Add-On Devices Connecting PC Cards Connecting PC Cards The computer’s PC Card slot is available for storing data and expanding the communication capabilities of the computer. The computer supports standard Type II and III PC Cards (PCMCIA and CardBus). If your model has two eject buttons, you can insert two Type II cards or one Type III card. If it has only one button, you can insert one card of any type. To insert or remove a PC Card Inserting a PC Card 1.
Add-On Devices Connecting PC Cards Removing a PC Card CAUTION Before removing a PC Card, you must use the Eject Hardware or Safely Remove Hardware icon in the taskbar, or shut down the computer. Otherwise, you could lose data. 1. Before removing the card, click the Eject Hardware or Safely Remove Hardware icon in the taskbar, and then click the card you want to remove. This protects your data and helps avoid unexpected problems. If needed, you can restart the card by removing and then reinserting it. 2.
Add-On Devices Connecting External Devices Connecting External Devices To identify connectors for external devices The diagrams below show your computer’s connectors for external devices and for the port replicator. Locating connectors on the computer 1. PS/2 keyboard or PS/2 mouse port (supports Y adapter). 2. AC adapter jack. 3. Two universal serial bus (USB) ports. 4. LAN port (on certain models). 5. S-video port (on certain models). 6. Parallel port (LPT1).
Add-On Devices Connecting External Devices 10. PC Card and CardBus slot. See “Connecting PC Cards” on page 76. 11. IEEE 1394 port (on certain models). 12. Audio ports. 13. Infrared port (on certain models). Locating connectors on the port replicator 14. AC adapter jack. 15. PS/2 keyboard and PS/2 mouse ports. 16. USB ports. 17. External monitor port. 18. Parallel port. 19. Serial port. 20. LAN port (works only if the computer has a built-in LAN port). 21. Digital audio port (SPDIF). 22. S-video port. 23.
Add-On Devices Connecting External Devices Note Before you connect any device, check its documentation to see if you need to make any settings or adjustments to the equipment before using it. This might include setting switches to configure the equipment so that it will operate properly with your computer and the software you plan to use.
Add-On Devices Connecting External Devices Note If you have problems making this connection, contact the device manufacturer and the HP Business Support Web site (www.hp.com/go/bizsupport) for the latest version of the driver for the device. To connect an audio device If your model has a built-in microphone—look for a microphone icon near the right click button on the touch pad—you can use it to record voice, sound, and music. You can also plug in an external microphone, external speakers, or headphones.
Add-On Devices Connecting External Devices Note If your model has a built-in microphone and you plug a device into the external microphone port, the built-in microphone automatically turns off. When you plug a device into the headphone port, the built-in speakers automatically turn off. When you plug a device into either audio port on the computer, any device connected to the corresponding port on the port replicator is ignored. To use an external monitor Connecting an external monitor 1.
Add-On Devices Connecting External Devices monitors vary greatly, and the display quality of your monitor may not be optimal at higher settings. If you need to increase the refresh rate on the external monitor, you can switch to only the external monitor. An alternative is to make one display a “secondary” display so you can select independent refresh rates: 1. Click Start, Control Panel, Appearance and Themes, Display. 2.
Add-On Devices Connecting External Devices composite phono (RCA-type) connection, a good-quality standard cable is recommended. However, some S-video/composite adapters will not work for this application. Contact HP Customer Care for more information. 2. Optional: connect an audio cable from the computer’s headphone output jack to the TV audio input. The S-video port doesn’t include audio output. To activate the TV display HP TV Now automatically adjusts your computer for using a TV.
Add-On Devices Connecting External Devices To connect an IEEE 1394 device If your computer has an IEEE 1394 port (located on the computer’s left side), you can use it to connect devices such as audio and video equipment, disk drives, printers, and other computers. • Attach the device’s cable to the IEEE 1394 port on the computer’s left side. Windows automatically recognizes the device. The IEEE 1394 port is a 4-wire port.
Add-On Devices Connecting External Devices Using the infrared port • Make sure the infrared ports of your computer and the other device lie in as straight a line as possible. The two ports should be no more than 1 meter apart, with no obstructions in between. Noise from nearby equipment can cause transmission errors. • To check the status of communications, open Wireless Link in Control Panel. Disabling the infrared port You should generally disable infrared communication when you aren’t using it. 1.
Add-On Devices Connecting External Devices To use a port replicator A port replicator provides your computer with external connections that you can leave in place whenever you remove the computer from your desk. Instead of disconnecting and reconnecting peripheral devices, you can simply undock and dock the computer. CAUTION Use only the HP AC adapter included with your computer (or other approved adapter that meets the power requirements of the computer).
Add-On Devices Connecting External Devices 4. Press the computer down until both sides click into place. 5. If the computer is off, open the computer and press the power button to turn it on. The lights on the port replicator turn on. When the computer is docked, you can use the computer’s security connector to secure the computer. To secure both the computer and port replicator, install the Kensington lock in the security connector next to the undock button—this locks the undock button.
Add-On Devices Installing Additional RAM Installing Additional RAM The computer has no memory (RAM) built in but has two slots that hold two RAM modules. At least one slot contains a RAM module installed at the factory. You can use both slots to expand your RAM. To install a RAM expansion module Use HP PC2100 DDR-266 or higher RAM only. You’ll need a small Phillips screwdriver for these steps.
Add-On Devices Installing Additional RAM To remove a RAM expansion module You may want to remove a RAM module so you can install a larger one. You’ll need a small Phillips screwdriver for these steps. CAUTION Your computer’s chips are extremely sensitive to static electricity, and can be permanently damaged by it. Handle the RAM module only by its edges.
Add-On Devices Replacing the Hard Disk Drive Replacing the Hard Disk Drive To replace the hard disk drive You’ll need a small Phillips screwdriver for this procedure. 1. Unplug the AC adapter if you’re using one, and remove the battery. 2. Turn the unit bottom side up. 3. Use a pointed tool to remove the plugs from the two screw holes, and then remove the two screws. 4. Gently pull the hard drive out of the computer. 5. Gently slide the new drive into the hard drive compartment.
Add-On Devices Replacing the Hard Disk Drive To replace the hard disk drive holder If you are installing a new hard drive that does not have a holder, you can remove the holder parts from the old hard drive. You’ll need a small Phillips screwdriver for this procedure. 1. Remove the four screws from the sides of the holder and drive case, and then slide the drive out of the holder. 2. Notice that the hard drive has a pin connector attachment at one end.
Add-On Devices Replacing the Hard Disk Drive To prepare a new hard disk drive When you install a new hard disk drive, you also need to prepare it to be able to work with your computer. • If you want to restore the Windows software and operating system that were originally installed on your computer, you can do so using the Recovery CD or DVD that also came with your computer. See “To recover the factory installation of your hard disk” on page 122.
Troubleshooting and Maintenance Reference Guide 95
Troubleshooting and Maintenance Troubleshooting Your Computer Troubleshooting Your Computer This section contains solutions to a many types of problems you might have with your computer. Try the solutions one at a time, in the order in which they are presented. Here are some other sources of information for troubleshooting: • Open the HP Web-based troubleshooting tool: click Start, All Programs, HP Instant Support. Search or browse the troubleshooting database for the information related to your problem.
Troubleshooting and Maintenance Troubleshooting Your Computer If sound does not record • Try plugging in an external microphone. Your model may not have a built-in microphone. • Check the software controls for recording sound: click Start, All Programs, Accessories, Multimedia (or Entertainment), Sound Recorder. • In Volume Control, click Options, Properties, and make sure the microphone is enabled in the recording controls. • Test the audio with the e-Diagtools diagnostics.
Troubleshooting and Maintenance Troubleshooting Your Computer If a DVD movie stops playing in the middle • The DVD may be double-sided. Open the DVD tray, and read the text near the center hole of the disc. If it says Side A, flip the disc over, close the tray, and press the Play button to continue playing the movie. • You may have accidentally paused the DVD movie. Press the Play button to resume.
Troubleshooting and Maintenance Troubleshooting Your Computer Display Problems If the computer is on, but the screen is blank • Move the mouse or tap the touch pad. This will wake the display if it is in Display-off mode. • Press Fn+F5 in case the internal display was disabled. (Do this three times to return to the state you started from.) • If the computer is cold, allow it to warm up.
Troubleshooting and Maintenance Troubleshooting Your Computer displays exhibit some level of cosmetic imperfection. These cosmetic imperfections may be visible under varying display conditions, and can appear as bright, dim, or dark spots. This issue is common across all vendors supplying TFT displays in their products and is not specific to the HP notebook display. HP notebook TFT displays meet or exceed all HP standards for cosmetic quality of TFT displays.
Troubleshooting and Maintenance Troubleshooting Your Computer • Run the virus-scanning program. See “To protect against viruses” on page 41. • Test the hard disk drive with the e-Diagtools diagnostics. See “Testing the Hardware” on page 115. • If necessary, you can format the hard disk and reinstall the original factory software. See “To recover the factory installation of your hard disk” on page 122. Heat Problems Your computer normally gets warm during routine operation.
Troubleshooting and Maintenance Troubleshooting Your Computer Keyboard and Pointing Device Problems Use these suggestions for built-in or external devices. If the pointer is difficult to control • Adjust the pointer controls: click Start, Control Panel, Printers and Other Hardware, Mouse. If the touch pad doesn’t work • Press the touch pad on-off button so the light turns on. • Don’t touch the touch pad while the computer is rebooting or resuming from Standby mode.
Troubleshooting and Maintenance Troubleshooting Your Computer • Make sure the embedded Keypad Lock (Fn+F8) is on—or that you press and hold the Fn key to temporarily access the embedded keypad. If you can’t type the euro symbol • Hold ALT GR when you press the marked key. • The euro symbol is not on the U.S. English keyboard. Make sure the embedded keypad is active (Fn+F8) and Num Lock is on, and then hold ALT while typing 0128 on the numeric keypad.
Troubleshooting and Maintenance Troubleshooting Your Computer If a network connection responds slowly • If your network connection uses a proxy server, try enabling the option for bypassing the proxy server for local addresses. You can do this in Control Panel under your network connection properties. Memory Problems If a message says you are out of memory • Make sure drive C is not running low on free space.
Troubleshooting and Maintenance Troubleshooting Your Computer • Eliminate extra connections in the line. If possible, connect directly to the wall jack. • Try another telephone line, preferably one normally used for a fax machine or modem. If the modem doesn’t dial or no dial tone is detected • Check all cables and connections. • Connect a standard telephone to the phone line and make sure the line is working. • Make sure someone else isn’t using the same phone line.
Troubleshooting and Maintenance Troubleshooting Your Computer If the modem isn’t detected • Check the modem setup. In Control Panel, open Phone and Modem Options. Check the COM port. • Open the hardware Device Manager: click Start, Control Panel, Performance and Maintenance, System. If the modem is disabled, try to enable it. If it has a conflict, try disabling another device. • If you’re running fax software using fax Class 2, try using Class 1.
Troubleshooting and Maintenance Troubleshooting Your Computer If the modem clicks repeatedly but doesn’t connect • Make sure you’re using an analog telephone line (2, 3, or 4 wires). You must not use a digital line. In a hotel, ask for a data line. • Check all cables and connections. PC Card (PCMCIA) Problems If the notebook doesn’t recognize a PC Card • Remove and reinsert the PC Card. • If your model has two PC Card slots and two eject buttons, insert the PC Card in a different slot.
Troubleshooting and Maintenance Troubleshooting Your Computer If an I/O card stops communicating properly • Exit and restart the application. The card may have been reset if the computer suspended or turned off. • Check settings in Control Panel. Performance Problems For best performance, your computer should have at least 128 MB of memory (RAM). If the computer pauses or runs sluggishly • This may be normal Windows behavior. Background processing can affect response time.
Troubleshooting and Maintenance Troubleshooting Your Computer Port Replicator Problems If a connection isn’t working • Check that AC power is connected to the port replicator, that the computer is fully docked, and that the port replicator lights are on. • Make sure the peripheral device has power connected and is turned on. • Make sure the device’s cable is connected properly. • The LAN port works only if the computer has a built-in LAN port.
Troubleshooting and Maintenance Troubleshooting Your Computer • If you’re using a power strip, remove the AC adapter from the power strip and plug it directly into a wall outlet. • Make sure the battery is fully installed and locked in place. • Make sure you’re using only the HP AC adapter included with your computer (or other approved adapter that meets the power requirements of the computer). If “75W” is printed below the AC adapter socket on the computer, do not use a 60-watt, 3.
Troubleshooting and Maintenance Troubleshooting Your Computer If the computer doesn’t suspend to Standby mode as expected • If you have a connection to another computer, the computer won’t suspend if the connection is active. • If the computer is performing an operation, it normally waits for the operation to finish before suspending. If the computer doesn’t automatically hibernate as expected • Make sure hibernate support is enabled.
Troubleshooting and Maintenance Troubleshooting Your Computer • Make sure Windows is running; otherwise infrared printing is not available. • See “Infrared Problems” on page 101. Serial, Parallel, and USB Problems If a serial mouse doesn’t work • Make sure you followed the manufacturer’s installation instructions completely and have installed the mouse properly. If not, repeat the procedure. • Make sure the port connection is secure. • Press the power button to suspend and resume.
Troubleshooting and Maintenance Troubleshooting Your Computer If the serial or parallel port is not working • Make sure the port connection is secure. • Check the port settings in Control Panel. Open the hardware Device Manager, and then double-click Ports (COM & LPT). • Test the ports with the e-Diagtools diagnostics. See “Testing the Hardware” on page 115. If the USB port is not working • Contact the vendor of the peripheral device— and the HP Business Support Web site (www.hp.
Troubleshooting and Maintenance Troubleshooting Your Computer If the computer won’t boot from the floppy disk drive • Make sure the floppy disk drive is selected as the boot device—see “To change the boot device” on page 27. • If you’re using a USB floppy drive, use the BIOS Setup utility to make sure Legacy USB Support is enabled—see “To run the BIOS Setup utility” on page 118 If the computer stops responding after booting • Check whether you are connected to a TCP/IP network with no DHCP server.
Troubleshooting and Maintenance Troubleshooting Your Computer If you cannot connect to a particular computer on the network • Make sure the computer is properly connected to the network. • Make sure your TCP/IP setup is correct for your network: in Control Panel, open Network Connections. If you can connect, but the network is slow • Check whether you might be in an area served by more than one wireless LAN. If so, the LANs could be interfering with each other.
Troubleshooting and Maintenance Testing the Hardware Testing the Hardware The e-Diagtools hardware diagnostic program included with your computer provides two levels of testing: • Automated testing using its basic hardware test. • Advanced testing using individual hardware tests. The tests are designed to run after the system reboots. This ensures that the computer will be in a predictable state, so the diagnostic program can properly test the hardware components.
Troubleshooting and Maintenance Testing the Hardware 12. Optional: open the Support Ticket. In Windows, click Start, All Programs, Hewlett-Packard, Notebook, HP e-Diagtools, e-Diagtools for Windows. 13. Click View to display the Support Ticket. 14. To add information about your problem, click Comments, type the information, and then click OK. To save or print the Support Ticket, click Save As or Print. To e-mail the Support Ticket to your support agent, click e-Mail.
Troubleshooting and Maintenance Configuring the Computer Configuring the Computer The BIOS Setup utility helps you configure your computer’s operation. To run the BIOS Setup utility The BIOS (Basic Input and Output System) Setup utility enables you to make changes to the computer’s system configuration, and to tailor the operation of your computer to your individual work needs. The settings made in BIOS Setup generally control the computer’s hardware, and so greatly affect how the computer operates. 1.
Troubleshooting and Maintenance Configuring the Computer Main Menu Setting Description Default BIOS Revision Shows the current BIOS version. Detected automatically. System Time Sets the time using 24-hour format. Values set take effect immediately. System Date Sets the date using dd/mm/yy format (except English, which uses mm/dd/yy format). Language Sets the language for BIOS Setup. Detected automatically. Internal Hard Disk Sets the hard disk drive type and various parameters.
Troubleshooting and Maintenance Configuring the Computer System Devices Menu Setting Description Default Video Display Device Sets whether the built-in display automatically switches to an external display, if one is detected. Auto External Pointing Device Disables the internal pointing devices when an external pointing device is connected. Auto Legacy USB Support Enables BIOS support for USB mouse, keyboard, and floppy disk drive during startup.
Troubleshooting and Maintenance Configuring the Computer Boot Menu Setting Description Default Hard Disk Removable Device CD-ROM/DVD Built-in LAN Shows the order of boot devices. Move the entries to change the order. Built-in LAN provides diskless boot from a network server. 1. Hard Disk 2. Removable Device 3. CD-ROM/DVD 4. Built-in LAN Setting Description Default Save Changes and Exit Saves Setup changes, and then exits and reboots.
Troubleshooting and Maintenance Reinstalling and Updating Software Reinstalling and Updating Software You can use the Recovery CD or DVD to recover the original software build for your computer. The Recovery CD or DVD also provides Windows drivers specific to your computer to configure a custom system. You can find drivers in these locations: • On your computer’s hard drive under C:\hp\Drivers. • On the Recovery CD or DVD under \hp\Drivers. • On the HP Business Support Web site (www.hp.com/go/bizsupport).
Troubleshooting and Maintenance Reinstalling and Updating Software 7. When the Recovery CD or DVD dialog box appears, follow the displayed instructions. To perform a standard recovery, press 2, 1, 1. If prompted, accept the recommended partition size. If you install the factory software, the recovery process can take 15 to 45 minutes. If you want to create the Utility partition without installing the factory software, click Advanced and select the option to not install the operating system.
Troubleshooting and Maintenance Reinstalling and Updating Software 5. Connect any cables or equipment needed to connect to the Internet. 6. Click Start, All Programs, Hewlett-Packard, Notebook, HP e-Diagtools, e-Diagtools for Windows. 7. Click Update, select Download Now and click OK. Follow the instructions that appear. Once the update process begins, do not interrupt it.
HP Support and Service Reference Guide 125
HP Support and Service Getting Assistance for Your Computer Getting Assistance for Your Computer To get help from the Web HP has several Web sites on the Internet dedicated to providing information to HP notebook computer users. The following sites are especially useful for helping you get support for your computer: • HP Business Support Web site. Get e-mail and telephone support information, technical information, and software updates. www.hp.com/go/bizsupport • HP Notebook Computer Web site.
HP Support and Service Getting Assistance for Your Computer To contact the HP Customer Care Center by e-mail, visit the HP Business Support Web site (www.hp.com/go/bizsupport) under “Contact HP”. To call the Customer Care Center, check the HP Business Support Web site (www.hp.com/go/bizsupport) under “Contact HP” for the most complete and current list of phone numbers.
HP Support and Service Getting Assistance for Your Computer To receive repair service If the HP notebook product is not normally sold by HP in the country of use, it must be returned for service to a country in which it is sold and supported. Note HP Pavilion notebooks have regional support and service in selected countries. Currently, HP Pavilion notebook PCs are supported only in the country in which they are purchased and marketed.
HP Support and Service Getting Assistance for Your Computer To prepare your computer for shipment See “To receive repair service” above to determine if your computer must be sent in for service. If so, prepare your computer for shipment as follows. Note If you have questions about packaging requirements when returning your notebook for repair, contact HP Service and Support—see “To contact HP for support or service” on page 126.
HP Support and Service Hewlett-Packard Limited Warranty Statement Hewlett-Packard Limited Warranty Statement 1. HP warrants to you, the end-user customer, that HP hardware, accessories and supplies will be free from defects in materials and workmanship after the date of purchase, for the period specified in the Warranty Duration table below. If HP receives notice of such defects during the warranty period, HP will, at its option, either repair or replace products which prove to be defective.
HP Support and Service Hewlett-Packard Limited Warranty Statement 7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE YOUR SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
Reference Information Reference Guide 133
Reference Information Hardware Specifications Hardware Specifications Technology Codes Each HP notebook computer has a two-letter technology code. The technology code is shown on the serial-number label on the bottom of the computer, and it is also included in the BIOS version number. Because we are constantly improving our products, the specifications shown below are subject to change. For the latest specifications, see the HP Notebook Web site (www.hp.com/notebooks).
Reference Information Hardware Specifications Power Rechargeable lithium-ion (14.8 Vdc) battery with LED charge-level gauge. Battery life: up to 3 hours typical (varies with model, usage, and power settings). Fast battery recharge: 2 hours when system is off, 3 hours when system is on. Low-battery warning. Suspend/resume capability. Universal AC adapter: 100–240 Vac (50/60 Hz) input, 19 Vdc output, 75 W. Mass Storage 20- to 60-GB removable hard drive with Ultra-DMA 100 interface. 1.
Reference Information Hardware Specifications Wireless LAN (certain models) Radio: IEEE 802.11b, WECA Wi-Fi compliant, direct-sequence spread-spectrum. Operating frequency: 2.4-GHz ISM band, exact frequencies and channels depend on country. Raw data rate: 1, 2, 5.5, or 11 Mbps. Transmitter output: 15 dBm typical (approx. 30 mW), 16 dBm max (approx. 40 mW). Receiver sensitivity: –84 dBm typical. Range: up to 100 m (300 ft) or more, depending on environment and conditions. On-off button and indicator.
Reference Information Hardware Specifications Major ICs Models with Technology Code KA: CPU: AMD Athlon or Duron processor. Core logic: ATI U1 / ALI 1535+ chipset. Display controller: ATI M6 integrated in core logic. Audio/Modem controller: Conexant Smart AMC CX20468-21. CardBus controller: O2Micro 6912. Keyboard/embedded controller: National PC87570. Super I/O: integrated in core logic. IEEE 1394: TI TSB43AB22. LAN: National NS83815. 802.11b wireless LAN: Ambit with Intersil Prism 2.5 chipset.
Reference Information Modem Reference Information Modem Reference Information If your computer has a modem port, you can customize the operation of the modem using AT commands and S-registers. You can do this from Phone and Modem Options in Control Panel, from most communications software, or by using terminal mode in your software. See “To change your modem settings” on page 60. Note You should have a good understanding of modems and how they operate before you change default settings.
Reference Information Modem Reference Information Command Function (Conexant) Mn Activate speaker: 0=off, 1=on during handshaking and off when receiving carrier (default), 2=always on, 3=off when dialing and receiving carrier, on when answering. Included for compatibility only; returns result code. 0=go on-line, 1=go on-line and initiate retrain sequence. Force pulse dialing. 0=enable result codes to DTE (default), 1=disable. Select S-register n as default. Set default S-register n to value v.
Reference Information Modem Reference Information Command Function (Conexant) +ESA=a,b,c,d,e,f,g,h Controls operation of synchronous access mode: a=0 specifies in transparent sub-mode, modem transmits 8-bit SYN sequence on idle. b=0 specified in framed sub-mode, modem transmits HDLC flags on idle (default and fixed).
Reference Information Modem Reference Information Command Function (Conexant) +VRID=n -QCPC -QCPS=n &Cn &Dn Report caller ID: 0=use formatted presentation, 1=use unformatted presentation. Use full startup procedures on next connection, then select startup procedure defined by +PQC. 0=do not allow modem to save generated quick-connect profile, 1=allow (default) Set RLSD: 0=always on, 1=follow carrier state (default).
Reference Information Modem Reference Information Command Function (Conexant) +MS=a,b,c,d,e,f Select modulation (b, c, d, e, and f are optional). a is the carrier (allowable rates in parentheses): B103 (300), B212 (1200 Rx/75 Tx or 75 Rx/1200 Tx), V21 (300), V22 (1200), V22B (1200/2400), V23C (1200), V32 (4800/9600), V32B (4800–14400), V34 (2400–33600), K56 (32000–56000), V90 (28000–56000), V92 (downstream: 28000–56000; upstream: 24000–48000). b is automode: 0=disabled, 1=enabled (default).
Reference Information Modem Reference Information Command Function (Conexant) +FMI +FMM +FMR +FPR=n +FRH=n +FRM=n +FRS=n +FTH=n +FTM=n +FTS=n Report modem manufacturer. Report modem model. Report modem version, revision, or date. Set DTE/modem interface rate in bits/sec: 0=automatic detection (default). Receive data with HDLC framing. Receive data. Receive silence, n×10 ms. Transmit data with HDLC framing. Transmit data. Stop transmission and wait, n×10 ms.
Reference Information Modem Reference Information S-Registers (Conexant) Register Function (Conexant) Range/units Default S0 S1 S2 S3 S4 S5 S6 S7 S8 S10 S11 S12 S18 S29 S30 S46 Number of rings to auto-answer. Ring counter. Escape character. Line termination character. Response formatting character. Command line editing character. Wait time for dial tone. Wait time for carrier. Pause time for dial delay modifier. Carrier loss disconnect time. DTMF tone duration. Escape prompt delay. Test timer.
Reference Information Safety Information Safety Information Power Cords The power cord supplied with the computer’s AC adapter should match the plug and voltage requirements for your local area. Regulatory approval for the AC adapter has been obtained using the power cord for the local area. However, if you travel to a different area or need to connect to a different outlet or voltage, you should use one of the power cords listed below.
Reference Information Safety Information Ergonomics WARNING Improper use of keyboards and other input devices has been associated with ergonomic injury. For information about reducing your risk, see Working in Comfort in the online HP Library or visit our ergonomics Web site, www.hp.com/ergo.
Reference Information Safety Information Laser Safety The CD-ROM and DVD drives used with the computer are certified as a Class 1 laser devices according to the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard and International Standards IEC 825 / IEC 825-1 (EN60825 / EN60825-1). These devices are not considered harmful, but the following precautions are recommended: • Ensure proper use by reading and following the instructions carefully.
Reference Information Safety Information Mercury Safety This product contains mercury in the fluorescent lamp of the liquid-crystal display, and may require special handling at end-of-life. Exposure to Radio Frequency Radiation The radiated output power of the IEEE 802.11 and Bluetooth internal wireless radio is far below the FCC radio frequency exposure limits. Nevertheless, the wireless radio shall be used in such a manner that the potential for human contact during normal operation is minimized.
Reference Information Regulatory Information Regulatory Information This section presents information that shows how your computer complies with regulations in certain regions. Any modifications to your computer not expressly approved by Hewlett-Packard could void the authority to operate the computer in these regions. U.S.A. This computer has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Reference Information Regulatory Information Declaration of Conformity (U.S.A.) Responsible Party: Hewlett-Packard Company Manager of Corporate Product Regulations 3000 Hanover Street Palo Alto, CA 94304 +1 (650) 857-1501 declares that the product(s) Trade name: Hewlett-Packard Company Product name: HP Pavilion ZE4... and XT... series Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
Reference Information Regulatory Information European Union The equipment has been approved in accordance with Council Decision 98/482/EC for pan-European single terminal connection to the public switched telephone network (PSTN) and to a radio-frequency wireless network. However, due to differences between the individual PST’s provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Reference Information Regulatory Information Die Geräte wurden gemäß Ratsentscheidung 98/482/EC für den Anschluss an eine einzelne Telefonbuchse im europäischen Raum (Public Switched Telephone Network) und drahtlose Funknetzwerke zertifiziert. In Anbetracht der Unterschiede zwischen den einzelnen Telefonnetzen bietet die Zertifizierung für sich genommen keine absolute Sicherheit, dass die Geräte bei Anschluss an jeder beliebigen Telefonbuchse funktionieren.
Reference Information Regulatory Information Japan Japan Telecommunications Approval Name of Equipment: AMC20493-001-KT1, AMC20493-001-KT3, AMC20493-001-KT5, AMC20493-001 TELEC approval number: D02-0005JP Name of Equipment: T60H424 Reference Guide 153
Reference Information Regulatory Information Russia International Products sold internationally by Hewlett-Packard and its authorized dealers meet the specifications listed on the following page. Note For regulatory identification purposes, your product is assigned a Regulatory Model Number. The Regulatory Model Number for your product is listed in the declaration below. This regulatory number is different from the marketing name and product number.
Reference Information Regulatory Information Declaration of Conformity (according to ISO/IEC Guide 22 and EN 45014) Manufacturer’s Name: Manufacturer’s Address: Hewlett-Packard Company, Mobile Computing Division 19310 Pruneridge Ave., Cupertino, CA 95014, U.S.A. declares that the following product Product Name: Regulatory Model Numbers: Product Options: Omnibook XE4... series, Pavilion ZE4... and ZE5... series, Pavilion XT...
Index A AC adapter compatibility, 21, 87 connecting, 21 AC adapter jack location, 15 accessories buying, 12 adding RAM, 89 AdHoc wireless network setting up, 65 adjusting brightness, 30, 34 display colors, 34 screen area, 34 volume, 30 airplanes wireless communication in, 66, 68 ALT GR key, 33 antistatic precautions, 89, 90 Applications key, 32 AT commands, 60, 138 audio adjusting volume, 35, 96 connecting devices, 81 muting, 35 troubleshooting, 96 volume, 30 audio jacks, 15 audio mute button, 15 B battery
BIOS settings, 120 brightness, 30, 34, 45, 52 dual display, 83 dual monitor, 83 extending life, 45 external, 82 port, 15 power, 53 quality, 100 secondary, 83 settings, 34 switching to external, 33 troubleshooting, 99 display colors adjusting, 34 docking port replicator, 87 docking port, 16 dragging items, 29 drive lock, 41 drivers downloading, 124 drives hard drive holder, 92 hard drive lock, 41 replacing hard disk, 91, 93 DVD drive location, 14 playing movies, 38 setting region code, 38 troubleshooting, 97
status, 14, 17, 18 locking computer, 39 LPT1 port, 15 M Main menu (BIOS), 119 memory adding, 89 extended, 119 PC2100 DDR-266, 89, 104 removing, 90 troubleshooting, 104 video, 119 microphone location, 14 mini-PCI location, 16 modem AT commands, 60, 138 black list, 58 blackout periods, 58 built-in, 22 connecting, 57 connecting to Internet, 58 dial-in connection, 59 faxing, 62 port location, 15 sending e-mail, 61 settings, 60 software, 56 troubleshooting, 104 monitor BIOS settings, 120 external, 82 port, 15 r
resolution external monitor, 82 S safety battery use, 146 infrared port, 147 laser, 147 power cords, 145 wireless communication, 66, 68 saving battery power, 52 screen area adjusting, 34 scroll pad location, 14 secondary display, 83 security hard drive lock, 41 Kensington lock, 15, 40, 88 Norton AntiVirus, 41 Security menu (BIOS), 120 selecting items, 29 sending faxes, 62 serial connections Bluetooth, 72 serial port connecting, 85 location, 15 troubleshooting, 112 setting up, 19 shut down, 50 software pre-
