abner.bk : 0_fcvr.
abner.bk : 0_fcvr.
abner.bk : 0_front.
abner.bk : 0_front.fm5 Page viii Monday, June 23, 1997 2:40 PM © Copyright 1997, Hewlett-Packard Company All Rights Reserved. Reproduction, adaptation, or translation without prior permission is prohibited, except as allowed under the copyright laws. Publication Number J3257-90004 Edition 1 June 1997 Disclaimer The information contained in this document is subject to change without notice.
Contents Installing the HP AdvanceStack Remote 2C Verifying Included Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Mounting the Remote 2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Remote 2C in a Rack or Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Mounting the Remote 2C on a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing a Module into the Remote 2C . . . . . . . . . . . . . . . . . . . . .
iv
abner.bk : 0_perf.fm5 Page 3 Monday, June 23, 1997 2:40 PM HP Customer Support Services The warranty booklet shipped with the HP Remote 2C describes the support for this product. For module updates, see HP’s Web Site. For white papers and module updates, see HP’s web site or HP’s fax retrieval service as described below. World Wide Web http://www.hp.com/go/network_city From this web site, you can access information on the HP networking products.
abner.bk : 0_perf.fm5 Page 4 Monday, June 23, 1997 2:40 PM Additional HP Support Services In addition to the above services, you can purchase various HP telephone support services which provide you expert HP technical assistance: ■ Network Phone-In Support provides you support at an hourly rate. In the U.S., call 1-800-790-5544. In other countries, please contact your local HP Response Center to see if this service is available in your country.
abner.bk : 1_instal.fm5 Page 1 Monday, June 23, 1997 2:40 PM Installing the HP AdvanceStack Remote 2C The features of the HP J3257A AdvanceStack Remote 2C are: ■ Two Slots for Modules. These slots will accept the HP J3138A AdvanceStack Internet Router Modules. (Other modules may be available. Contact your HP-reseller or authorized dealer for details.) In the Remote 2C, you can install one of each module above or two modules of the same type.
abner.bk : 1_instal.
abner.bk : 1_instal.fm5 Page 3 Monday, June 23, 1997 2:40 PM Mounting the Remote 2C The Remote 2C can be mounted in three ways: ■ on a table ■ in a rack or cabinet ■ on a wall Sturdy table in an isolated area Remote 2C in a Rack or Cabinet The Remote 2C is designed to be mounted in any EIA-standard 19-inch telco equipment rack. For your safety, read the mounting precautions in “Safety and Regulatory” at the end of this guide before mounting the Remote 2C. 1.
abner.bk : 1_instal.fm5 Page 4 Monday, June 23, 1997 2:40 PM 2. Partially install a screw (5/8-inch number 12-24) into the top hole of a pair of holes 0.5 inches apart in each rack/cabinet upright. Tighten each screw two turns. Ensure that the screws in each upright are at the same level. 3. Place the HP Remote 2C in the rack and lower it so the notches in the bottom of the bracket slide onto the screws. Tighten these screws-be careful not to overtighten.
abner.bk : 1_instal.fm5 Page 5 Monday, June 23, 1997 2:40 PM Mounting the Remote 2C on a Wall You can put one Remote 2C on a wall or stack two Remote 2Cs together on a wall. Note that a Remote 2C should be mounted only to a wall or wood surface that is at least 1/2-inch plywood or its equivalent.
abner.bk : 1_instal.fm5 Page 6 Monday, June 23, 1997 2:40 PM Installing a Module into the Remote 2C To install a module into the Remote 2C, follow these steps: 1. The modules are “hot swappable”. You can leave the power on while inserting modules. (Note that each module and Remote 2C will be reset when you insert a module). Remove the cover plate on either slot: Loosen these screws 2.
abner.bk : 1_instal.fm5 Page 7 Monday, June 23, 1997 2:40 PM 5. Each module is shipped with a module label. Insert the module’s label into the front of the Remote 2C for the module in the back of the Remote 2C: Slide the Module label in until each word is legible: Connecting Cables From the Remote 2C To the Office LAN The Remote 2C has two RJ-45 ports on the front of the box for connecting each module to your LAN.
abner.bk : 1_instal.fm5 Page 8 Monday, June 23, 1997 2:40 PM Example 2: Remote 2C connected to an Ethernet Switching Hub-12R and a 100VG Hub-14 Remote 2C Ethernet Hub-12R 100VG Hub-14 LED should light if power is connected to the Remote 2C and hubs. 8 Category 3, 4, or 5 unshielded twisted pair.
abner.bk : 1_instal.fm5 Page 9 Monday, June 23, 1997 2:40 PM Connecting an HP Remote 2C and HP Internet Router Module To a 100VG Network If you have the following topology: To A 100VG Network Back of Remote 2C HP Internet Router Module (in either slot of the Remote 2C) In the above topology, HP does not recommend configuring the HP Internet Router Module for bridging. Instead configure the router to route IP, IPX, and Appletalk protocols.
abner.bk : 1_instal.fm5 Page 10 Monday, June 23, 1997 2:40 PM 2. If you are not using an RPS, plug the included power cord into the Remote 2C’s power cord receptacle and into an AC power source as shown below. Power receptacle on the back of the Remote 2C 3. After power has been applied to the Remote 2C, it executes a self test. Check the LEDs during self test. Self test lasts up to 3 seconds for the Remote 2C and then each module executes its own self test simultaneously.
abner.bk : 1_instal.fm5 Page 11 Monday, June 23, 1997 2:40 PM Description of LEDs on the Remote 2C The Remote 2C has the following LEDs: LED State Meaning Power (green) ON The Remote 2C is receiving power. OFF The Remote 2C is not receiving power. Global Fault (orange) ON One or both slot modules experienced a hardware problem. RPS (green) OFF The Remote 2C is not receiving power from the HP J2962A Redundant Power Supply (RPS). ON The Remote 2C is receiving power from the connected RPS.
abner.bk : 1_instal.fm5 Page 12 Monday, June 23, 1997 2:40 PM Where to Go From Here You are now finished installing the Remote 2C. Software configuration for the AdvanceStack Internet Router is needed. See that manual now. Removing A Module from the Remote 2C The module is removed from the Remote 2C by reversing the installation steps described earlier in this guide. To remove the module, follow these steps: 1. Disconnect any cables connected to the module(s). 2.
abner.bk : 1_instal.fm5 Page 13 Monday, June 23, 1997 2:40 PM Troubleshooting the Remote 2C Use the following table to determine the problem with your Remote 2C. Also consult the LED table on page 11. If you are still having problems with the Remote 2C, see the Customer Support page at the beginning of this manual for information on how to contact HP. Problem Solution All LEDs are lit on the Remote 2C Verify that each module is fully inserted, extractor handles down, screws tightened. and remain lit.
abner.bk : 1_instal.fm5 Page 14 Monday, June 23, 1997 2:40 PM Specifications Physical Width 44.2 cm (17.4 in) Depth 29.8 cm (11.7 in) Height 6.6 cm (2.6 in) Weight 4.4 kg (9.8 lb) (with no modules in the Remote 2C) Electrical The Remote 2C automatically adjusts to any voltage between 100-127 and 200-240 volts and either 50 or 60 Hz. Operating Non-Operating AC voltage: 100-127 volts 200-240 volts Maximum current: 1.3 A 0.
abner.bk : 1_instal.fm5 Page 15 Monday, June 23, 1997 2:40 PM Environmental Operating Temperature Non-Operating Temperature Temperature +0°C to +55°C (32°F to 131°F) -40°C to 70°C (-40°F to 158°F) Relative humidity (non-condensing) 15% to 95%at 40°C (104°F) 15% to 90% at 65°C (149°F) Maximum altitude 4.6 km (15,000 ft) 4.
abner.bk : 1_instal.
abner.bk : 2_safety.fm5 Page 17 Monday, June 23, 1997 2:40 PM Safety and Regulatory Statements This chapter covers the following topics: ■ mounting precautions ■ power precautions ■ safety and regulatory statements ■ Declaration of Conformity Mounting Precautions When you put the Remote 2C into a rack, follow these mounting precautions: ■ The rack or cabinet should be adequately secured to prevent it from becoming unstable and/or falling over. The first unit (e.
abner.bk : 2_safety.fm5 Page 18 Monday, June 23, 1997 2:40 PM Safety and Regulatory Statements Power Precautions Power Precautions Follow these precautions when unplugging and plugging in power to the Remote 2C as well as adding or removing modules. Caution If your installation requires a different power cord than the one supplied with the Remote 2C, be sure to use a power cord displaying the mark of the safety agency that defines the regulations for power cords in your country.
abner.bk : 2_safety.fm5 Page 19 Monday, June 23, 1997 2:40 PM Safety and Regulatory Statements Safety Information Safety Information ! Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death. CAUTION A CAUTION in the manual denotes a hazard that can damage equipment.
abner.bk : 2_safety.fm5 Page 20 Monday, June 23, 1997 2:40 PM Safety and Regulatory Statements Informations concernant la sécurité Informations concernant la sécurité ! Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la documentation du produit afin d'obtenir des informations plus détaillées. WARNING Dans la documentation, un WARNING indique un danger susceptible d'entraîner des dommages corporels ou la mort.
abner.bk : 2_safety.fm5 Page 21 Monday, June 23, 1997 2:40 PM Safety and Regulatory Statements Hinweise zur Sicherheit Hinweise zur Sicherheit ! Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten. WARNING Symbol für Dokumentationsverweis.
abner.bk : 2_safety.fm5 Page 22 Monday, June 23, 1997 2:40 PM Safety and Regulatory Statements Considerazioni sulla sicurezza Considerazioni sulla sicurezza ! Simbolo di riferimento alla documentazione. Se il prodotto è contrassegnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso. WARNING La dicitura WARNINGdenota un pericolo che può causare lesioni o morte. CAUTION La dicituraCAUTION denota un pericolo che può danneggiare le attrezzature.
abner.bk : 2_safety.fm5 Page 23 Monday, June 23, 1997 2:40 PM Safety and Regulatory Statements Consideraciones sobre seguridad Consideraciones sobre seguridad ! Símbolo de referencia a la documentación. Si el producto va marcado con este símbolo, consultar la documentación del producto a fin de obtener mayor información sobre el producto. WARNING Una WARNING en la documentación señala un riesgo que podría resultar en lesiones o la muerte.
abner.bk : 2_safety.
abner.bk : 2_safety.fm5 Page 25 Monday, June 23, 1997 2:40 PM Safety and Regulatory Statements Regulatory Statements Regulatory Statements FCC Class A Statement (for U.S.A. Only): This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
abner.bk : 2_safety.fm5 Page 26 Monday, June 23, 1997 2:40 PM Safety and Regulatory Statements Declaration of Conformity Declaration of Conformity The following Declaration of Conformity for the HP AdvanceStack Remote 2C complies with ISO/IEC Guide 22 and EN 45014. The declaration identifies the product, the manufacturer’s name and address, and the applicable specifications that are recognized in the European community.
abner.bk : cvrbak.
abner.bk : cvrbak.fm5 Page 32 Monday, June 23, 1997 2:40 PM Technical information in this document is subject to change without notice.
