J3138.
J3138.
J3138.bk Page 1 Wednesday, March 18, 1998 6:07 PM Support is as close as the World Wide Web! http://www.hp.com/go/network_city Follow the links that lead you to Support, Drivers, and Technology.
J3138.bk Page 2 Wednesday, March 18, 1998 6:07 PM HP FIRST Fax Retrieval Service HP FIRST is an automated fax retrieval service that is available 24 hours a day, seven days a week. HP FIRST provides a variety of product and technical information. To access HP FIRST, dial one of the following telephone numbers: ■ In the U.S. and Canada, dial 800-333-1917 from your fax machine or touch-tone phone.
J3138.
J3138.bk Page iv Wednesday, March 18, 1998 6:07 PM © Copyright 1998 Hewlett-Packard Company All Rights Reserved. This document contains information which is protected by copyright. Reproduction, adaptation, or translation without prior permission is prohibited, except as allowed under the copyright laws. Publication Number J3138-90003 January 1998 Applicable Product Disclaimer The information contained in this document is subject to change without notice.
J3138.bk Page v Wednesday, March 18, 1998 6:07 PM Contents 1 HP AdvanceStack Internet Router Overview Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Software Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Based on Cisco IOS version 11.x. Cisco IOS Software Category — Desktop without IBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Ordering Information . . . . .
J3138.bk Page vi Wednesday, March 18, 1998 6:07 PM 3 Configuring the HP AdvanceStack Internet Router Booting the Router for the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Configuring the Router for the First Time . . . . . . . . . . . . . . . . . . . . . . 3-2 Using the System Configuration Dialog . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the ISDN BRI Interface . . . . . . . . . . . . . . . . . . . . . . . . Configuring Ethernet or VG Interfaces . . . . . . . . .
J3138.bk Page vii Wednesday, March 18, 1998 6:07 PM A Cable Specifications Console and Auxiliary Port Signals and Pinouts . . . . . . . . . . . . . . . . A-1 Identifying a Roll-Over Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Console Port Signals and Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3 Auxiliary Port Signals and Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4 Synchronous Serial Cable Assemblies and Pinouts . . . . .
J3138.
J3138.bk Page 1 Wednesday, March 18, 1998 6:07 PM 1 HP AdvanceStack Internet Router Overview This router provides an easy to install, cost efficient and scalable connectivity solution for small offices needing access to the Internet or for remote offices requiring access to a central site, especially central sites equipped with Cisco Systems™ routers. It is based on Cisco’s 2503 hardware platform and includes all its hardware features except the PCMCIA support for Flash memory. Figure 1-1.
J3138.bk Page 2 Wednesday, March 18, 1998 6:07 PM HP AdvanceStack Internet Router Overview Hardware Features Overview Hardware Features 1-2 ■ Internal Ethernet, IEEE (Institute of Electrical and Electronics Engineers) 802.3 and 802.12 connection to an HP AdvanceStack host device ■ Two high speed (T1/E1, i.e., 1.544 Mbps/2.048 Mbps) synchronous WAN ports with shielded DB-60 connectors.
J3138.bk Page 3 Wednesday, March 18, 1998 6:07 PM HP AdvanceStack Internet Router Overview Software Features Software Features Overview Based on Cisco IOS version 11.x. Cisco IOS Software Category — Desktop without IBM ■ LAN support — IP, transparent bridging and translational bridging, concurrent routing and bridging, LAN extension host, GRE, Novell, IPX, AppleTalk 1 and 2, DECnet IV. ■ WAN services — HDLC, PPP, X.25, Frame Relay, ISDN, SMDS, SW56, IPXWAN 2.
J3138.bk Page 4 Wednesday, March 18, 1998 6:07 PM HP AdvanceStack Internet Router Overview Software Features Overview NOTE ■ PPP includes support for LAN protocols supported by the feature set, address negotiation, PAP and CHAP authentication, and PPP compression. ■ X.25 includes switching. ■ ISDN support includes calling line identification (ANI), X.25 over the B channel, ISDN subaddressing, and applicable WAN optimization features.
J3138.bk Page 5 Wednesday, March 18, 1998 6:07 PM HP AdvanceStack Internet Router Overview Ordering Information Ordering Information The HP AdvanceStack Router is accompanied with the following cables and adapters. Refer to appendix A, “Cable Specifications” for more details on the cables.
J3138.bk Page 6 Wednesday, March 18, 1998 6:07 PM HP AdvanceStack Internet Router Overview Ordering Information Documentation and Software Overview The HP AdvanceStack Internet Router software documentation and latest release of IOS software is on HP’s web site. To obtain the documentation, follow these steps: 1. Open your web browser and point the browser to: http://www.hp.com/go/network_city 2. Click on Support. 3. Click on Internet Router. 4. Click on Product Manuals. 5.
J3138.bk Page 1 Wednesday, March 18, 1998 6:07 PM 2 Installing the HP AdvanceStack Internet Router This chapter covers the hardware installation process for the HP AdvanceStack Internet Router. For details on configuring the HP AdvanceStack Internet Router refer to chapter 3, “Configuring the HP AdvanceStack Internet Router”.
J3138.bk Page 2 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Required Tools and Parts Required Tools and Parts The router installation requires some tools and parts that are not provided as standard equipment with the router. Following are the tools and parts required to install the router: ■ Flat-blade screwdrivers: small, 3/16-inch (0.476 cm) and medium, 1/4-inch (0.
J3138.bk Page 3 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Preparing to Connect to a Network ISDN Connections Use a BRI cable to connect the router directly to an ISDN. (See table 2-1.) Network hazardous voltages are present in the BRI cable. If you detach the BRI cable, detach the end away from the router to avoid possible electric shock.
J3138.bk Page 4 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Preparing to Connect to a Network Synchronous Serial Connections Before you connect a device to the synchronous serial port, you will need to know the following: ■ The type of device, DTE or DCE, you are connecting to the synchronous serial interface ■ The type of connector, male or female, required to connect to the device. ■ The signaling standard required by the device.
J3138.bk Page 5 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Preparing to Connect to a Network Signaling Standards Supported The synchronous serial port supports the following signaling standards: EIA/ TIA-232, EIA/TIA-449, V.35, X.21, and EIA-530. You can order a DB-60 shielded serial transition cable from HP that has the appropriate connector for the standard you specify.
J3138.bk Page 6 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Preparing to Connect to a Network Balanced drivers allow EIA/TIA-449 signals to travel greater distances than the EIA/TIA-232 signals. Table 2-4 lists the maximum speeds and distances for EIA/TIA-449, which are also valid for V.35, X.21, and EIA-530 signals. Installation Table 2-4. CAUTION EIA/TIA-449, V.35, X.
J3138.bk Page 7 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Preparing to Connect to a Network Console Port Connections Auxiliary Port Connections The router includes an EIA/TIA-232 asynchronous serial auxiliary port (RJ-45) that supports flow control. Depending on the cable and the adapter used, this port will appear as a DTE or DCE device at the end of the cable. Your router includes a cable and an adapter to connect a modem to the auxiliary port.
J3138.bk Page 8 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Installing the Module Installing the Module The HP AdvanceStack Internet Router module can be installed in any HP AdvanceStack host device such as hubs or switches with an Expansion Slot. Expansion Slot is the official name for the slot in an HP AdvanceStack host device which can take an add-on module such as this router module.
J3138.bk Page 9 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Installing the Module Insert the HP Internet Router module into the HP AdvanceStack host device. 3. Lift the extractor handles up. 4. Tighten the two screws that hold it in place. Be careful not to overtighten the screws. 5. On the front of the host device, remove the blank label from the Expansion Slot LEDs. 6. Insert the router module label. Installation 2.
J3138.bk Page 10 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Connecting to the Network Connecting to the Network Installation This section explains how to connect the router to your network. The LAN connection is made automatically when the router is installed in the host device. The synchronous serial and ISDN ports are used to connect the router to a WAN. NOTE Not all the cables required to connect the router to a network are provided with the router.
J3138.bk Page 11 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Connecting to the Network 2. Use a straight-through RJ-45-to-RJ45 cable to connect the ISDN BRI port (RJ-45) to an NT1 device. Installation Figure 2-2. Connecting the ISDN BRI Port to an NT1 Device Connecting the Console Terminal and Modem Use a console terminal for local administrative access to the router. You can connect only a terminal to the console port.
J3138.bk Page 12 Wednesday, March 18, 1998 6:07 PM Installation Installing the HP AdvanceStack Internet Router Connecting to the Network Figure 2-3. Connecting the Console Terminal 2. 2-12 Configure your terminal or PC terminal emulation software for 9600 baud, 8 data bits, no parity, and 2 stop bits.
J3138.bk Page 13 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router Connecting to the Network Connecting a Modem to the Auxiliary Port Take the following steps to connect a modem to the auxiliary port on the router: 1. Use an RJ-45 roll-over cable with an RJ-45-to-DB-25 or RJ-45-to-DB-9 adapter to connect a modem to the auxiliary port. The adapters provided by HP are labeled “Modem”. Installation Figure 2-4. Connecting a Modem to the Auxiliary Port 2.
J3138.bk Page 14 Wednesday, March 18, 1998 6:07 PM Installing the HP AdvanceStack Internet Router What to Do After Installing the Router Hardware What to Do After Installing the Router Hardware After you have installed the router, proceed to chapter 3 “Configuring the HP AdvanceStack Internet Router for initial software configuration information. Installation If you had trouble installing the router, see chapter 4, “Troubleshooting”.
J3138.
J3138.bk Page 2 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring the Router for the First Time indicates that the router should attempt to load a Cisco IOS image from Flash memory. Use the “show version” command at the privileged EXEC prompt to show the setting. 3. If after five attempts a valid Cisco IOS image is not found in Flash memory, the router reverts to boot ROM mode (which is used to install or upgrade a Cisco IOS image). 4.
J3138.bk Page 3 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring the Router for the First Time review of the Cisco IOS software, refer to the section “Cisco IOS Software Basics” later in this chapter. Otherwise, proceed with the next section “Using the System Configuration Dialog”. Using the System Configuration Dialog If you do not plan to use AutoInstall, make sure all the WAN cables are disconnected from the router.
J3138.bk Page 4 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring the Router for the First Time NOTE The default parameters for the console port are 9600 baud, 8 data bits, no parity, and 2 stop bits. 2. NOTE After about 30 seconds, information similar to the following is displayed on the console screen. The messages displayed vary, depending on the interfaces on the rear panel of the router and the Cisco IOS release and feature set you selected.
J3138.bk Page 5 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring the Router for the First Time 1 ISDN Basic Rate interface. 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read ONLY) Notice: NVRAM invalid, possibly due to write erase. --- System Configuration Dialog --At any point you may enter a question mark '?' for help. Refer to the 'Getting Started' Guide for additional help.
J3138.bk Page 6 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring the Router for the First Time 6. Enter an enable secret password: The enable secret is a one-way cryptographic secret used instead of the enable password when it exists. Enter enable secret: pail The enable password is used when there is no enable secret and when using older software and some boot images. 7.
J3138.bk Page 7 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring the Router for the First Time Table 3-1.
J3138.bk Page 8 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring the Router for the First Time Configuring Ethernet or VG Interfaces It is necessary to decide and configure the network protocols you want to support on the LAN interface. 1. Press Return to configure the LAN interface: Configuring interface Ethernet0: (or VG0 depending on what device the router module has been attached to) Is this interface in use? [yes]: Configuration 2.
J3138.bk Page 9 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring the Router for the First Time 2. Determine which protocols you want on the synchronous serial interface and enter the appropriate responses. In the following example, the system is configured for IP, AppleTalk, and IPX: Configure IP on this interface? [yes]: Configure IP unnumbered on this interface? [no]: IP address for this interface: 172.16.73.
J3138.bk Page 10 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring the Router for the First Time Proceed to the section “Cisco IOS Software Basics” for more information about the Cisco IOS software. Using Configuration Mode You can configure the router manually if you do not want to use AutoInstall or the prompt-driven System Configuration Dialog. Take the following steps to configure the router manually: 1.
J3138.bk Page 11 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring the Router for the First Time Refer to the Cisco IOS configuration guide and command reference publications for more information about the commands you can use to configure the router. To verify the configuration entries, use the “write terminal” command at the privileged EXEC prompt. 5.
J3138.bk Page 12 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Cisco IOS Software Basics 4. If AutoInstall completes successfully, enter the copy running-config startup-config command in privileged EXEC mode to write the configuration data to the router’s NVRAM: Router# copy running-config startup-config Taking this step saves the configuration settings that the AutoInstall process created to the router’s NVRAM.
J3138.bk Page 13 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Cisco IOS Software Basics Table 3-2. Cisco IOS Operating Modes Usage How to Enter the Mode Prompt User EXEC User EXEC commands allow you to connect to remote devices, change terminal settings on a temporary basis, perform basic tests, and list system information. The EXEC commands available at the user level are a subset of those available at the privileged level. Log in.
J3138.bk Page 14 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Cisco IOS Software Basics Almost every configuration command also has a “no” form. In general, use the “no” form to disable a feature or function. Use the command without the keyword “no” to reenable a disabled feature or to enable a feature that is disabled by default. For example, IP routing is enabled by default. To disable IP routing, enter the no ip routing command and enter ip routing to reenable it.
J3138.bk Page 15 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring ISDN Saving Configuration Changes Any time you make changes to the router configuration, you must save the changes to memory because if you do not they will be lost if there is a system reload or power outage. There are two types of configuration files: the running (current operating) configuration and the startup configuration.
J3138.bk Page 16 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring ISDN Take the following steps to configure the router for a basic ISDN PPP connection on a single B channel or two B channels, substituting the correct addresses and host names as appropriate for your network: 1. Enter privileged EXEC mode: Router> enable password: enablepassword 2. Enter the configure terminal command to enter global configuration mode.
J3138.bk Page 17 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring ISDN Router (config-if)# isdn spid1 SPID_no [LDN] Router (config-if)# isdn spid2 SPID_no [LDN] 7. Configure the router for PPP encapsulation and CHAP authentication: Router (config-if)# encapsulation ppp Router (config-if)# ppp authentication chap 8. Enter the load-threshold or ppp multilink command to set up a second B channel.
J3138.bk Page 18 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring ISDN 12. Enter the dialer list command to specify the groups and protocols permitted to access the router: Router (config)# dialer-list groupnumber protocol protocol_type permit 13. Configure a static route to allow connection to the target router’s LAN.
J3138.bk Page 19 Wednesday, March 18, 1998 6:07 PM Configuring the HP AdvanceStack Internet Router Configuring ISDN Table 3-3. Example ISDN Configuration Configuration for the Current Router Router> enable password: pail2 Router# config term Router (config)# hostname main1 main1 (config)# username branch1 password secret1 main1 (config)# isdn switch-type basic-dms100 main1 (config)# interface Ethernet 0 main1 (config-if)# ip address 172.16.64.190 255.255.255.
J3138.
J3138.bk Page 1 Wednesday, March 18, 1998 6:07 PM 4 Troubleshooting A This chapter contains information about troubleshooting and maintenance procedures you might need to perform on your router as your internetworking needs change.
J3138.bk Page 2 Wednesday, March 18, 1998 6:07 PM Troubleshooting Reading the LEDs Table 4-1 describes the LEDs which are located on the front panel of the host device. Table 4-1. LEDs on the Host Device Front Panel LED State Description WAN 1 Activity Off Inactivity on the synchronous serial port 1. If you are sure some data activity is going on this port, check the serial 1 cable connection. On/Flashing Transmitting/Receiving data on the synchronous serial port 1.
J3138.bk Page 3 Wednesday, March 18, 1998 6:07 PM Troubleshooting Reading the LEDs Table 4-2 describes the LEDs, which are located on the front panel of the HP AdvanceStack Internet Router. Table 4-2. LEDs on the HP AdvanceStack Internet Router Front Panel LED State Description ISDN BRI Off Inactivity on the ISDN BRI port. If you are sure some data activity is going on this port, check the BRI cable connection. On/Flashing Transmitting/Receiving data on the ISDN BRI port. Off Power if off.
J3138.bk Page 4 Wednesday, March 18, 1998 6:07 PM Troubleshooting Upgrading the Boot ROMs For troubleshooting information, refer to the System Error Messages and Debug Command Reference publications of Cisco Systems, found on the CD-ROM accompanying the router. You can also access “Technical Assistance” at the World Wide Web URL http://www.cisco.com (Cisco Connection Online) for a list of frequently asked questions and other technical tips. Upgrading the Boot ROMs The Boot ROMs are not user upgradeable.
J3138.bk Page 5 Wednesday, March 18, 1998 6:07 PM Troubleshooting Recovering Lost Passwords NOTE 3. Enter the show version command to display the existing configuration register value. The configuration register value is on the last line of the display. Note whether the configuration register is set to enable or disable Break. 4. The factory-default configuration register value is 0x2102. Notice that the third digit from the right in 0x2102 is 1, which disables Break.
J3138.bk Page 6 Wednesday, March 18, 1998 6:07 PM Troubleshooting Recovering Lost Passwords 12. Enter privileged EXEC mode and then enter the show startup-config command to display the passwords in the configuration file: Router> enable Router# show startup-config 13. Scan the configuration file displayed for the passwords (the enable and enable secret passwords are usually near the beginning of the file and the console password is near the end of the file).
J3138.bk Page 7 Wednesday, March 18, 1998 6:07 PM Troubleshooting Recovering Lost Passwords You can remove individual passwords by using the no form of these commands. For example, enter the no enable secret command to remove the enable secret password. 17. Configure all interfaces to be administratively up.
J3138.bk Page 8 Wednesday, March 18, 1998 6:07 PM Troubleshooting Virtual Configuration Register Settings Virtual Configuration Register Settings The router has a 16-bit virtual configuration register, which is written into NVRAM.
J3138.bk Page 9 Wednesday, March 18, 1998 6:07 PM Troubleshooting Virtual Configuration Register Settings Changing Configuration Register Settings Take the following steps to change the configuration register while running the Cisco IOS software: 1. Enter the enable command and your password to enter privileged mode: Router> enable Password: Router# 2. Enter the configure terminal command at the privileged EXEC prompt (Router#): Router# configure terminal 3.
J3138.bk Page 10 Wednesday, March 18, 1998 6:07 PM Troubleshooting Virtual Configuration Register Settings 6. Reboot the router. The new value takes effect. Configuration register changes take effect only when the router restarts, which occurs when you switch the power OFF and ON or when you enter the reload command. Virtual Configuration Register Bit Meanings The lowest four bits of the virtual configuration register (bits 3, 2, 1, and 0) form the boot field. (See table 4-4.
J3138.bk Page 11 Wednesday, March 18, 1998 6:07 PM Troubleshooting Virtual Configuration Register Settings Table 4-5.
J3138.bk Page 12 Wednesday, March 18, 1998 6:07 PM Troubleshooting Virtual Configuration Register Settings Bit 8 controls the console Break key. Setting bit 8 (the factory default) causes the processor to ignore the console Break key. Clearing bit 8 causes the processor to interpret the Break key as a command to force the system into the bootstrap monitor, thereby halting normal operation. A break can be sent in the first 60 seconds while the system reboots, regardless of the configuration settings.
J3138.bk Page 13 Wednesday, March 18, 1998 6:07 PM Troubleshooting Copying a Cisco IOS Image to Flash Memory Enabling Booting from Flash Memory To disable Break (after 60 seconds) and enable the boot system flash command, enter the config-register command with the value shown in the following example: Router> enable Password: enablepassword Router# config term Enter configuration commands, one per line.
J3138.bk Page 14 Wednesday, March 18, 1998 6:07 PM Troubleshooting Copying a Cisco IOS Image to Flash Memory The following messages display: **** NOTICE **** Flash load helper vX.0 This process will accept the copy options and then terminate the current system image to use the ROM based image for the copy. Routing functionality will not be available during that time. If you are logged in via telnet, this connection will terminate. Users with console access can see the results of the copy operation.
J3138.bk Page 15 Wednesday, March 18, 1998 6:07 PM Troubleshooting Copying a Cisco IOS Image to Flash Memory 9. Enter yes to confirm that you want to erase the contents of Flash memory. Messages similar to the following display: %SYS-5-RELOAD: Reload requested %FLH: master/igs-j-l.110-4.2 from 172.16.72.1 to flash ... System flash directory: File Length Name/status 1 3459776 username/igs-i-l [3459840 bytes used, 4928768 available, 8388608 total]Configuration mapped ip address 172.16.72.
J3138.
J3138.bk Page 17 Wednesday, March 18, 1998 6:07 PM Troubleshooting Inserting the HP Internet Router Module into an HP Remote 2C Inserting the HP Internet Router Module into an HP Remote 2C In the topology below, HP does not recommend configuring the HP Internet Router Module for bridging. Instead configure the router to route IP, IPX, and Appletalk protocols. This is because bridging forwards multicast and broadcast packets from the 100 Mbps network to the much slower T1 or ISDN lines.
J3138.
J3138.bk Page 1 Wednesday, March 18, 1998 6:07 PM A Cable Specifications Cable Specifications B This appendix provides the following pinout information: NOTE ■ Console and Auxiliary Port Signals and Pinouts ■ Synchronous Serial Cable Assemblies and Pinouts ■ ISDN BRI Port and Cable Pinouts All pins not listed in the tables in this appendix are not connected.
J3138.bk Page 2 Wednesday, March 18, 1998 6:07 PM Cable Specifications Console and Auxiliary Port Signals and Pinouts Cable Specifications Identifying a Roll-Over Cable You can identify a roll-over cable by comparing the two modular ends of the cable. Holding the cables side-by-side, with the tab at the back, the wire connected to the pin on the outside of the left plug should be the same color as the wire connected to the pin on the outside of the right plug. (See figure A-1).
J3138.bk Page 3 Wednesday, March 18, 1998 6:07 PM Cable Specifications Console and Auxiliary Port Signals and Pinouts Console Port Signals and Pinouts Table A-1.
J3138.bk Page 4 Wednesday, March 18, 1998 6:07 PM Cable Specifications Console and Auxiliary Port Signals and Pinouts Table A-2.
J3138.bk Page 5 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Table A-3. Auxiliary Port Signaling and Cabling Using a DB-25 Adapter RJ-45-to-RJ-45 Roll-Over Cable RJ-45-to-DB-25 Modem Adapter Modem Signal RJ-45 Pin RJ-45 Pin DB-25 Pin Signal RTS 1a 8 4 RTS DTR 2 7 20 DTR TxD 3 6 3 TxD GND 4 5 7 GND GND 5 4 7 GND RxD 6 3 2 RxD DSR 7 2 8 DCD CTS 81 1 5 CTS Cable Specifications Auxiliary Port (DTE) a.
J3138.bk Page 6 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts 60-pin connector 25-pin connector H1972 Cable Specifications J2-13 J2-25 J2-14 J2-1 Connectors are not to scale Figure A-3.
J3138.bk Page 7 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Table A-4.
J3138.bk Page 8 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Cable Specifications EIA/TIA-232 Figure A-4 shows the EIA/TIA-232 cable assembly. Table A-5 lists the DTE pinouts. Table A-6 lists the DCE pinouts. Arrows indicate signal direction: —> indicates DTE to DCE, and <— indicates DCE to DTE. 60-pin connector 25-pin connector H1972 J2-13 J2-25 J2-14 J2-1 Connectors are not to scale Figure A-4.
J3138.bk Page 9 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Table A-5. EIA/TIA-232 DCE Cable Pinouts (DB-60 to DB-25) Signal Description Direction 25 Pin Signal J1-50 J1-51 J1-52 MODE_0 GND MODE_DCE Shorting group – – – J1-46 Shield GND Single – J2-1 Shield GND J1-41 Shield TxD/RxD – Twisted pair no. 5 —> – J2-2 Shield TxD – J1-36 Shield RxD/TxD – Twisted pair no.
J3138.bk Page 10 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Cable Specifications Table A-6. A-10 EIA/TIA-232 DCE Cable Pinouts (DB-60 to DB-25) 60 Pin Signal Description Direction 25 Pin Signal J1-50 J1-51 MODE_0 GND Shorting group – – – J1-46 Shield GND Single – J2-1 Shield GND J1-36 Shield RxD/TxD – Twisted pair no. 9 <— – J2-2 Shield TxD – J1-41 Shield TxD/RxD – Twisted pair no.
J3138.bk Page 11 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts EIA/TIA-449 37-pin connector (J2) J2-19 J2-37 H1973 60-pin connector (J1) Connectors are not to scale J2-20 J2-1 Figure A-5. EIA/TIA-449 Cable Assembly A-11 Cable Specifications Figure A-5 shows the EIA/TIA-449 cable assembly. Table A-7 lists the DTE pinouts. Table A-8 lists the DCE pinouts. Arrows indicate signal direction: —> indicates DTE to DCE, and <— indicates DCE to DTE.
J3138.bk Page 12 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Cable Specifications Table A-7. A-12 EIA/TIA-449 DTE Cable Pinouts (DB-60 to DB-37) 60 Pin Signal Description Direction 37 Pin Signal J1-49 J1-48 MODE_1 GND Shorting group – – – J1-51 J1-52 GND MODE_DCE Shorting group – – – J1-46 Shield_GND Single _ J2-1 Shield GND J1-11 J1-12 TxD/RxD+ TxD/RxD– Twisted pair no.
J3138.bk Page 13 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Table A-8. EIA/TIA-449 DCE Cable Pinouts (DB-60 to DB-37) Signal Description Direction 37 Pin Signal J1-49 J1-48 MODE_1 GND Shorting group – – – J1-46 Shield_GND Single – J2-1 Shield GND J1-28 J1-27 RxD/TxD+ RxD/TxD– Twisted pair no. 11 <— <— J2-4 J2-22 SD+ SD– J1-13 J1-14 TxCE/TxC+ TxCE/TxC– Twisted pair no.
J3138.bk Page 14 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Cable Specifications V.35 Figure A-6 shows the V.35 cable assembly. Table A-9 lists the DTE pinouts. Table A-10 lists the DCE pinouts. Arrows indicate signal direction: —> indicates DTE to DCE, and <— indicates DCE to DTE. Connectors are not to scale Figure A-6. V.
J3138.bk Page 15 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Table A-9. V.
J3138.bk Page 16 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Cable Specifications Table A-10. V.
J3138.bk Page 17 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts X.21 60-pin connector (J1) 15-pin connector (J2) J2-8 J2-15 H1974 J1-46 J1-45 J1-16 J1-15 J1-1 J1-30 J1-31 J1-60 Connectors are not to scale J2-9 J2-1 Figure A-7. X.21 Cable Assembly A-17 Cable Specifications Figure A-7 shows the X.21 cable assembly. Table A-11 lists the DTE pinouts. Table A-12 lists the DCE pinouts.
J3138.bk Page 18 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Cable Specifications Table A-11. X-21 DTE Cable Pinouts (DB-60 to DB-15) A-18 60 Pin Signal Description Direction 15 Pin Signal J1-48 J1-47 GND MODE_2 Shorting group – – – J1-51 J1-52 GND MODE_DCE Shorting group – – – J1-46 Shield_GND Single – J2-1 Shield GND J1-11 J1-12 TxD/RxD+ TxD/RxD– Twisted pair no.
J3138.bk Page 19 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Table A-12. X.21 DCE Cable Pinouts (DB-60 to DB-15) Signal Description Direction 15 Pin Signal J1-48 J1-47 GND MODE_2 Shorting group – – – J1-46 Shield_GND Single – J2-1 Shield GND J1-28 J1-27 RxD/TxD+ RxD/TxD– Twisted pair no. 6 <— <— J2-2 J2-9 Transmit+ Transmit– J1-1 J1-2 CTS/RTS+ CTS/RTS– Twisted pair no.
J3138.bk Page 20 Wednesday, March 18, 1998 6:07 PM Cable Specifications Synchronous Serial Cable Assemblies and Pinouts Cable Specifications ISDN BRI Port and Cable Pinouts Table A-13 lists the ISDN BRI port pinouts. The straight-through RJ-45-to-RJ-45 cable, used to connect to the ISDN BRI port, is not included. Table A-13. BRI Port (RJ-45) Pinout RJ-45 8 Pina TEb NTc Polarity 3 Transmit Receive + 4 Receive Transmit + 5 Receive Transmit – 6 Transmit Receive – a.
J3138.bk Page 1 Wednesday, March 18, 1998 6:07 PM B HP J3138A Specifications Physical 15.5 cm (6.1 in) Depth: 11.8 cm (4.6 in) Height: 4.4 cm (1.7 in) Weight (without Modules or RPS: 0.13 kg (0.28 lbs) HP J3138A Specifications Width: Power Consumption +5 V 4.5 A max. +12 V 500 mA max. -12 V 300 mA max. Total Power Consumption 25 W max.
J3138.bk Page 2 Wednesday, March 18, 1998 6:07 PM HP J3138A Specifications Connectors The RJ-45 twisted-pair ports are compatible with the IEEE 802.3 Type 10Base-T standard. HP J3138A Specifications Electromagnetic Emissions: FCC part 15 Class A CISPR-22 Class A / EN 55022 Class A VCCI Level I Immunity: See the Declaration of Conformity for details at the end of the Safety and Regulatory Statements in the Switching Hubs manual. Safety: Complies with: IEC 950: (1991) + A1, A2 / .
J3138.bk Page 1 Wednesday, March 18, 1998 6:07 PM C Safety and Regulatory Statements Safety Information Safety Symbols. Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death. CAUTION A CAUTION in the manual denotes a hazard that can damage equipment.
J3138.bk Page 2 Wednesday, March 18, 1998 6:07 PM Safety and Regulatory Statements Informations concernant la sécurité Informations concernant la sécurité Symboles de sécurité Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la documentation du produit afin d’obtenir des informations plus détaillées. WARNING Dans la documentation, un WARNING indique un danger susceptible d’entraîner des dommages corporels ou la mort.
J3138.bk Page 3 Wednesday, March 18, 1998 6:07 PM Safety and Regulatory Statements Hinweise zur Sicherheit Hinweise zur Sicherheit Sicherheitssymbole. Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten. WARNING Eine WARNING in der Dokumentation symbolisiert eine Gefahr, die Verletzungen oder sogar Todesfälle verursachen kann.
J3138.bk Page 4 Wednesday, March 18, 1998 6:07 PM Safety and Regulatory Statements Considerazioni sulla sicurezza Considerazioni sulla sicurezza Simboli di sicurezza. Simbolo di riferimento alla documentazione. Se il prodotto è contrassegnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso. WARNING La dicitura WARNING denota un pericolo che può causare lesioni o morte.
J3138.bk Page 5 Wednesday, March 18, 1998 6:07 PM Safety and Regulatory Statements Consideraciones sobre seguridad Consideraciones sobre seguridad Símbolos de seguridad. Símbolo de referencia a la documentación. Si el producto va marcado con este símbolo, consultar la documentación del producto a fin de obtener mayor información sobre el producto. WARNING Una WARNING en la documentación señala un riesgo que podría resultar en lesiones o la muerte.
J3138.
J3138.bk Page 7 Wednesday, March 18, 1998 6:07 PM Safety and Regulatory Statements Regulatory Statements Regulatory Statements FCC Class A Statement (for U.S.A. Only) when using unshielded cables. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
J3138.bk Page 8 Wednesday, March 18, 1998 6:07 PM Safety and Regulatory Statements Regulatory Statements FCC Part 68. General Requirements ■ This equipment complies with part 68 of the FCC rules. On the back of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.
J3138.bk Page 9 Wednesday, March 18, 1998 6:07 PM Safety and Regulatory Statements Regulatory Statements For service: Hewlett-Packard Company 3625 Cincinnati Avenue Rocklin, California 95765-1288 VCCI Class 1 (For Japan Only). Note This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Complies with Canadian EMC Class A requirements.
J3138.
J3138.bk Page 1 Wednesday, March 18, 1998 6:07 PM Index Numerics 100VG network bridging … 4-17 11.
J3138.bk Page 2 Wednesday, March 18, 1998 6:07 PM D DCE cable pinouts … A-5–A-17 documentation where to get it … 1-6 DTE cable pinouts … A-5–A-17 ISDN BRI configuring … 3-7, 3-15–3-19 example configuration … 3-19 LED … 4-2 switch types … 3-7 K key, Break (interrupt) … 4-12 E EIA/TIA-232 pinout and signals … A-8 EIA/TIA-449 pinout and signals … A-11 EIA-530 pinout and signals … A-5 electromagnetic specifications … B-2 enable command … 3-10 Ethernet configuring … 3-8 LED … 4-3 L F name for 11.
J3138.
J3138.
J3138.
J3138.bk Page 6 Wednesday, March 18, 1998 6:07 PM Technical information in this document is subject to change without notice.
