Getting Started Compaq Notebook
© Copyright 2011 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ..................................................................................................................... 4 Top ....................
Turning the TouchPad off and on ...................................................................... 21 Navigating ......................................................................................................... 21 Selecting ........................................................................................................... 22 Using TouchPad gestures ................................................................................. 22 Scrolling ..............................................
1 Welcome ● Finding information After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, refer to Networking on page 14. ● Set up HP QuickWeb—Immediately access the Internet, widgets, and communications programs without launching your main operating system. For more information, refer to HP QuickWeb (select models only) on page 12.
Finding information The computer comes with several resources to help you perform various tasks. Resource Contents Instructions for setting up the computer ● How to set up the computer ● Identification of computer components Getting Started ● Computer features To access this guide: ● Instructions for the following: Select Start > All Programs > HP Help and Support > HP Documentation.
Resource Contents Worldwide Telephone Numbers booklet HP customer support telephone numbers This booklet is provided with your computer. HP Web site ● Customer support information To access this Web site, go to http://www.hp.com/ support. ● Information for ordering parts ● Software, driver, and BIOS updates ● Information about accessories for the computer Limited Warranty* Warranty information To access the warranty: Select Start > All Programs > HP Help and Support > HP Documentation.
2 Getting to know your computer ● Top ● Right side ● Left side ● Display ● Bottom Top TouchPad Component (1) 4 Description TouchPad light ● Amber: The TouchPad is off. ● Off: The TouchPad is on. (2) TouchPad on/off button Turns the TouchPad on and off. Quickly double-tap the TouchPad on/off button to turn the TouchPad on and off. (3) TouchPad zone Moves the pointer and selects or activates items on the screen.
Component Description (4) Left TouchPad button Functions like the left button on an external mouse. (5) Right TouchPad button Functions like the right button on an external mouse. Lights Component (1) (2) (3) (4) Description TouchPad light Caps lock light Power light Wireless light ● Amber: The TouchPad is off. ● Off: The TouchPad is on. ● White: Caps lock is on. ● Off: Caps lock is off. ● White: The computer is on. ● Blinking white: The computer is in the Sleep state.
Buttons Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) Action keys Execute frequently used system functions. (3) fn key Displays system information when pressed in combination with the esc key. (4) Windows logo key Displays the Windows Start menu. (5) QuickWeb key ● When the computer is off or in Hibernation, press the button to open HP QuickWeb.
Right side Component Description (1) Optical drive (select models only) Reads and writes to an optical disc. (2) Optical drive light ● On: The optical drive is in use. ● Off: The optical drive is idle. (3) USB ports (2) Connect optional USB devices. (4) Power connector Connects an AC adapter. (5) AC adapter light ● White: The computer is connected to external power and the battery is fully charged. ● Amber: A battery is charging.
Left side Component Description (1) External monitor port Connects an external VGA monitor or projector. (2) Vents (2) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (3) RJ-45 (network) jack Connects a network cable.
Display Component Description (1) Send and receive wireless signals to communicate with wireless local area networks (WLAN). WLAN antennas (2)* NOTE: Select computer models only have one WLAN antenna. (2) Webcam light On: The webcam is in use. (3) Webcam Records video and captures still photographs. To use the webcam, select Start > All Programs > Communication and Chat > CyberLink YouCam. (4) Internal microphone Records sound.
Bottom Component Description (1) Battery bay Holds the battery. (2) Battery release latch Releases the battery from the battery bay. (3) Vents (5) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (4) Hard drive bay Holds the hard drive. (5) Memory module compartment Contains the memory module slots.
3 HP QuickWeb (select models only) ● Starting HP QuickWeb The HP QuickWeb environment provides a fun and engaging way to perform many of your favorite activities. Your computer is ready to go within seconds of starting QuickWeb, allowing you to rapidly access the Internet, widgets, and communication programs. Simply press the QuickWeb key (or QuickWeb button on select models), and then start browsing the Internet, communicating with Skype, and exploring other HP QuickWeb programs.
Starting HP QuickWeb ▲ To start HP QuickWeb, press the QuickWeb key (or QuickWeb button on select models) when the computer is off or in Hibernation. The following table explains the different behaviors of the QuickWeb key (or QuickWeb button on select models). Key Behavior QuickWeb key (or QuickWeb button on select models) ● When the computer is off or in Hibernation, opens HP QuickWeb. ● When the computer is in Microsoft Windows, opens the default Web browser.
4 Networking ● Using an Internet service provider (ISP) ● Connecting to a wireless network NOTE: Internet hardware and software features vary depending on computer model and your location. Your computer may support one or both of the following types of Internet access: 14 ● Wireless—For mobile Internet access, you can use a wireless connection. Refer to Connecting to an existing WLAN on page 16 or Setting up a new WLAN network on page 16.
Using an Internet service provider (ISP) Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP to purchase Internet service and a modem. The ISP will help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service. NOTE: Your ISP will give you a user ID and password to access the Internet. Record this information and store it in a safe place.
Connecting to an existing WLAN 1. Turn on the computer. 2. Be sure that the WLAN device is on. 3. Click the network icon in the notification area, at the far right of the taskbar. 4. Select a network to connect to. 5. Click Connect. 6. If required, enter the security key.
Configuring a wireless router For help in setting up a WLAN, refer to the information provided by your router manufacturer or your ISP. The Windows 7 operating system also provides tools to help you set up a new wireless network. To use the Windows tools to set up your network: ● Select Start > Control Panel > Network and Internet > Network and Sharing Center > Set up a new connection or network > Set up a network. Then follow the on-screen instructions.
5 Keyboard and pointing devices ● Using the keyboard ● Using pointing devices Using the keyboard Using the action keys Action keys are used for performing customized actions that are assigned to specific keys at the top of the keyboard. The icons on the f1 through f12 keys represent the action key functions. To use an action key, press and hold this key to activate the assigned function. NOTE: The action key feature is enabled at the factory. You can disable this feature in Setup Utility.
Icon Action Description Switch screen image Switches the screen image among display devices connected to the system. For example, if a monitor is connected to the computer, this key alternates the screen image from computer display to monitor display to simultaneous display on both the computer and the monitor. Most external monitors receive video information from the computer using the external VGA video standard.
Using pointing devices NOTE: In addition to the pointing devices included with your computer, you can use an external USB mouse (purchased separately) by connecting it to one of the USB ports on the computer. Setting pointing device preferences Use Mouse Properties in Windows® to customize settings for pointing devices, such as button configuration, click speed, and pointer options. To access Mouse Properties, select Start > Devices and Printers.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad on/off button. NOTE: The TouchPad light is off when the TouchPad is on. Navigating To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go.
Selecting Use the left and right TouchPad buttons like the corresponding buttons on an external mouse. Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. To view the demonstration of a gesture: 1. Select Start > Control Panel > Hardware and Sound > Synaptics > Settings. 2. Click a gesture to activate the demonstration.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad, and then drag them across the TouchPad in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. NOTE: Two-finger scrolling is enabled at the factory. Pinching/Zooming Pinching allows you to zoom in or out on images or text. ● Zoom in by placing two fingers together on the TouchPad, and then moving them apart.
Rotating (select models only) Rotating allows you to rotate items such as photos. To rotate, anchor your left forefinger in the TouchPad zone. Move the right forefinger around the anchored finger in a sweeping motion, moving from 12 o’clock to 3 o’clock. To reverse the rotation, move your right forefinger from 3 o’clock to 12 o’clock. NOTE: Rotating is disabled at the factory. NOTE: Rotating must be done within the TouchPad zone.
6 Maintenance ● Inserting or removing the battery ● Replacing or upgrading the hard drive ● Adding or replacing memory modules Inserting or removing the battery NOTE: For additional information on using the battery, refer to the HP Notebook Reference Guide. To insert the battery: ▲ Insert the battery (1) into the battery bay, and then pivot the battery (2) downward until it is seated.
CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and initiate Hibernation or shut down the computer through Windows before removing the battery. 26 1. Slide the battery release latch (1) to release the battery. 2. Tilt the battery (2) to remove it, and then lift it out of the battery bay (3).
Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. Removing the hard drive 1.
7. Remove the hard drive cover (2). 8. Disconnect the hard drive cable (1) from the computer. 9. Remove the 4 hard drive screws (2). 10. Lift the hard drive (3) out of the hard drive bay. Installing a hard drive 28 1. Insert the hard drive (1) into the hard drive bay. 2. Replace the 4 hard drive screws (2).
3. Connect the hard drive cable (3) to the computer. Slide the cable under the plastic notches. 4. Align the tabs on the hard drive cover (1) with the notches on the computer. 5. Close the cover (2). 6. Tighten the hard drive cover screw (3). 7. Align the tabs on the memory module compartment cover (1) with the notches on the computer. 8. Close the cover (2).
9. Tighten the memory module compartment cover screw (3). 10. Replace the battery. 11. Reconnect external power and external devices. 12. Turn on the computer. Adding or replacing memory modules The computer has two memory module slots. The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot.
CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before adding or replacing memory modules. Do not remove a memory module while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. 1. Save your work and shut down the computer. 2. Disconnect all external devices connected to the computer.
b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 7. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 8. Align the tabs on the memory module compartment cover (1) with the notches on the computer. 9. Close the cover (2). 10. Tighten the memory module compartment cover screw (3). 11. Replace the battery.
12. Reconnect external power and external devices. 13. Turn on the computer.
7 Backup and recovery Your computer includes tools provided by the operating system and HP to help you safeguard your information and restore it if ever needed.
Restore In the event of hard drive failure, to restore your system to its factory image you will need a set of recovery discs or a recovery flash drive that you can create using HP Recovery Manager. HP recommends that you use this software to create either a set of recovery discs or a recovery flash drive immediately after software setup.
To create a set of recovery discs or a recovery flash drive: 1. Select Start > All Programs > Security and Protection > HP Recovery Manager > HP Recovery Media Creation. 2. Follow the on-screen instructions. Performing a system restore HP Recovery Manager software allows you to repair or restore the computer to its original factory state. HP Recovery Manager works from recovery discs, a recovery flash drive, or from a dedicated recovery partition (select models only) on the hard drive.
Restoring using the restore media 1. If possible, back up all personal files. 2. Insert the first recovery disc into the optical drive on your computer or an optional external optical drive, and then restart the computer. – or – Insert the recovery flash drive into a USB port on your computer, and then restart the computer. NOTE: If the computer does not automatically restart in the HP Recovery Manager, the computer boot order needs to be changed. 38 3. Press f9 at system bootup. 4.
Changing the computer boot order To change the boot order for recovery discs: 1. Restart the computer. 2. Press esc while the computer is restarting, and then press f9 for boot options. 3. Select Internal CD/DVD ROM Drive from the boot options window. To change the boot order for recovery flash drive: 1. Insert the flash drive into a USB port. 2. Restart the computer. 3. Press esc while the computer is restarting, and then press f9 for boot options. 4.
To create a screen shot: 1. Display the screen you want to save. 2. Copy the screen image: To copy only the active window, press alt+prt sc. To copy the entire screen, press prt sc. 3. Open a word-processing document, and then select Edit > Paste. The screen image is added to the document. 4. Save and print the document. Using Windows Backup and Restore Guidelines: ● Be sure that the computer is connected to AC power before you start the backup process.
Using Windows system restore points A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes. NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails created since the last restore point. You also can create additional restore points to provide increased protection for your files and settings.
8 Customer support ● Contacting customer support ● Labels Contacting customer support If the information provided in this user guide, in the HP Notebook Reference Guide, or in Help and Support does not address your questions, you can contact HP Customer Support at: http://www.hp.com/go/contactHP NOTE: For worldwide support, click Contact HP worldwide on the left side of the page, or go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact technical support. The serial number label is affixed to the bottom of the computer.
9 Specifications ● Input power ● Operating environment Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz.
Operating environment Factor Metric U.S.
Index A AC adapter light, identifying 8 action keys adjusting volume 19 audio CD, DVD, or BD controls 19 decrease screen brightness 18 Help and Support 18 identifying 7 increase screen brightness 18 muting speaker sound 19 switching screen image 19 wireless 19 adapter, AC 8 audio-in (microphone) jack, identifying 9 audio-out (headphone) jack, identifying 9 B backing up customized window, toolbar, and menu bar settings 39 personal files 39 battery bay 11, 43 battery release latch 11 battery, replacing 25 Bl
removing 31 replacing 30 memory module compartment cover removing 27, 31 replacing 29, 33 memory module compartment, identifying 11 Microsoft Certificate of Authenticity label 43 mouse, external setting preferences 20 mute key, identifying 19 N network jack, identifying 9 O operating environment 45 operating system Microsoft Certificate of Authenticity label 43 Product Key 43 optical drive, identifying 8 P pinching TouchPad gesture 23 pointing devices, setting preferences 20 ports external monitor 9 HDMI
