Quick Reference Guide

2
4
6
8
9
9
10
11
11
12
12
1
3
5
7
Memory Board Components
Item Description
1
2
3
4
5
6
7
8
9
10
11
12
Memory error has occurred on this bank and system has failed over to
the online spare bank.
4
3
1
2
5
5
6
On-Line Spare
M
E
M
O
R
Y
S
T
A
T
U
S
2
8
7
6
5
4
3
1
A
B
Online Spare Status
Mirroring Status
Ready to Hot-Plug
431
2
5 6
Memory Board Status LEDs
2
7
8
8
9
6
6
5
4
3
4
3
1
Exterior View of Server
Simplex
Duplex
SCSI IDs
0123
0101
432 85 6 7
10
1
24
23
22 20 19 1718 13 121521
15
16
11
9
2
4
5
6
7
Multibay 2 (DVD-ROM)
1
Eject button for
multibay 1
Eject button for
multibay 2
External health LED
Front Unit Identification
LED and Switch
Internal health LED
3
Multibay 1 (Diskette)
8
Power On/Standby
button and LED
9
11
12
14
Hot-plug disk
drive bays 1-4
Redundant hot-plug
power supply
Dual Port PCI-X 1000T
Gigabit NIC
AC inlet (redundant)
Primary hot-plug power
supply
18
22
21
19
20
USB connector 1
Serial connector
USB connector 2
Video connector
17
Integrated
Lights-Out
Network port
connector
23
Mouse connector
Keyboard
connector
13
AC inlet (primary)
2
4
5
6
7
1
3
8
9
11
12
14
1010
19
23
22
20
21
18
Rear Unit
Identification
LED and switch
17
24
13
Torx T-15 wrench (access
panel removal tool)
15
PCI-X Hot Plug
slots 1, 3-6
16
14
Power Supply LEDs
Remove power
supply
Install Power Supply
Replacing a Redundant Hot-Plug
Power Supply
3
2
4
5
7
6
1
2
1
No AC power
Power LED
(Green)
1 2
Fault LED
(Amber)
Status
On
Off
Blinking
Off
Off
On
Off
Off
No AC power to this
specific power supply
Or
Power supply
failure
AC power present
System in standby mode
Power supply on and
working properly
On Blinking
Power supply current limit
exceeded
5i Plus Memory Module Cabling
Remote Insight Management Cabling
Opening and Removing the Rear Access Panel
Line up guide marks on access
panel and chassis to install and
remove the panels.
1
2
4
3
3
5
5
System Configuration
1
2
3 4 5
34
Slots 1 through 6 are
PCI-X 64-bit, 100 MHz
33
32
FRONT
1
3
4
7
5
6
Non-hot-plug slot 1
Hot-plug slot 3
Hot-plug slot 6
Hot-plug slot 4
Hot-plug slot 5
Memory board slot 2
Memory board slot 1
2
Non-hot-plug slot 2
9
8
Fan 4
10
12
13
14
Fan 7
Processor Power Module (PPM) 1
PPM 2
Processor 1
Processor 2
11
15
17
26
19
PPM 3
Processor 4
PPM 4
Fan 3
16
Processor 3
28
Fan 1
29
Fan 2
31
24
SCSI port A
On SCSI backplane
SCSI Simplex/Duplex switch
33
Configuration Maintenance
Switch (SW4)
34
System ID Switch (SW7)
Integrated Lights-Out override
switch (SW8)
6
10
12
29
28
30
9
26 24
30
Pass-through board connector
25
25
SCSI port B
15
16
17
35
Simplex
Duplex
8
Integrated Lights-Out diagnostic LEDs
35
19
18
31
20
Battery backed write cache
enabler *
27
22
23
Bus
10
Bus
6
Bus
2
11
Non-Maskable Interrupt (NMI)
switch
32
21
20
22
27
Fan 6
Battery
Fan 5
23
21
5i Plus Memory Module connector
Switch
S1
S2
S3
S4
Function (bold is default)
Reserved
S5
S6
Reserved
Off = System configuration can
be changed
On = Power-On password is
disabled
Off = Power-On password
works normally
Off = Configuration valid
S7
Off = Disable
On = Enable
S8
Off = Disable
On = Enable
33
Configuration Maintenance Switch (SW4)
Off = Booting from floppy disk
is controlled by config
On = Booting from floppy disk
is enabled and config is
overridden
On = System configuration is
locked and cannot be
modified
Switch
Function (bold is default)
On = ROM treats system
configuration as invalid
7
18
30-pin Remote Insight
Lights-Out Edition II Board
connector
PCI-X Hot Plug board
connector
36
37
36
37
* Optional on some models.
Position
2
1
Indication
Reserved
35
Integrated Lights-Out Override Switch (SW8)
Off = Normal (default)
On = Override
iLO securtiy
override
Description
14
13
Removing the Front Access Panel
1
2
3
3
Installing a SCSI Drive
1
2
3
4
Removing and Installing a
Multibay Drive
2
1
1
3
2
4
6
2
5
4
3
1
4
3
5
8
7
6
9
10
1
2
11
12
1
2
Replacing a Hot-Plug Fan