Installation Guide HP 9000 rp7420 Server Fourth Edition Manufacturing Part Number : A7025-96014 October 2006 Printed in the U.S.A. © Copyright 1979-2006 Hewlett-Packard Development Company, L.P.
Legal Notices © Copyright 2006 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Revision History First Edition Initial release. December 2003.
Contents 1. Introduction Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cell Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tables Table 1-1. PCI-X Slot Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Table 2-1. Wheel Kit Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Table 2-2. Caster Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Table 3-1. HP 9000 rp7420 Server PCI-X I/O Cards . . . . . . . . . . . . . . .
Tables vi
Figures Figure 1-1. HP 9000 rp7420 Server with mounted bezel (Front View) . . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 1-2. Right-Front View of HP 9000 rp7420 Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Figure 1-3. Left-Rear View of HP 9000 rp7420 Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 1-4. Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures viii
1 Introduction The HP 9000 rp7420 Server is a member of the HP business-critical computing platform family: a mid-range, mid-volume server, positioned as a performance upgrade to the HP 9000 rp7410 product. The HP 9000 rp7420 Server shares the same hardware as the HP 9000 rp7410 with changes to the cell board, CPU modules, core I/O, and the PCI-X backplane.
Introduction Overview Overview The HP 9000 rp7420 Server is a 10U, 8-socket Symmetric Multi-Processing, rack-mount server that accommodates up to 64 GB of memory; PCI-X I/O, and internal peripherals, including disks and DVD/tape. Its high availability features include N+1 hot-pluggable fans and power, redundant power cords, and hot-pluggable PCI-X cards and internal disks. It currently uses dual core, PA-RISC processors.
Introduction Overview Figure 1-1 • HP 9000 rp7420 Server with mounted bezel (Front View) Depth: Defined by cable management constraints to fit into standard 36-inch deep racks: 25.5 inches from front rack column to PCI connector surface 26.7 inches from front rack column to MP Core I/O connector surface 30 inches overall package dimension, including 2.7 inches protruding in front of the front rack columns • Width: 44.45 cm (17.5 inches), constrained by EIA standard 19 inch racks • Height: 10U – 0.
Introduction Overview See Figure 1-2 on page 5 for component location. The mass storage section located in the front allows access to the hard disk drives without removal of the bezel (bezel removed in figure). Removing the bezel allows access to the removable media drive, the front fans and the bulk power supplies. The mass storage bay accomodates one 5.25-inch removable media drive and up to four 3.5-inch hard disk drives.
Introduction Overview Figure 1-2 Right-Front View of HP 9000 rp7420 Server PCI/PCI-X slots Hard Disk Drives Front panel display board Removable Media bay PCI-X fan modules Cell 0 Cell 1 PCI Power modules Front fans Bulk powers supplies Chapter 1 5
Introduction Overview Figure 1-3 Left-Rear View of HP 9000 rp7420 Server System Backplane Rear fans MP/SCSI Core I/O card Slot 0 MP/SCSI Core I/O card Slot 1 AC Power Receptacles See Figure 1-3 for component locations described below. When facing the front of the server, access the system backplane by removing the left side cover (cover removed in figure and shown here from the rear).
Introduction Overview Front Panel Front Panel Indicators and Controls The front panel, located on the front of the server, includes the power switch and status LEDs. See Figure 1-4.
Introduction Overview I/O Subsystem All of the I/O is integrated into the system by way of the PCI-X buses. The CC on each cell board communicates with one system bus adapter (SBA). The SBA converts the SBA link protocol into “ropes”. A rope is defined as a high-speed, point-to-point data bus. The SBA can support up to 16 of these high-speed bi-directional links for a total aggregate bandwidth of approximately 4GB/s. The server supports a maximum of two SBAs.
Introduction Overview Table 1-1 I/O Partition PCI-X Slot Types Devicea Slot 0 8 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot 0 7 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot 0 6 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot 0 5 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot 0 4 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.
Introduction Overview Internal Disk Devices for the HP 9000 rp7420 Server In an HP 9000 rp7420 Server, the top internal disk drives connect to cell 1 through the core I/O for cell 1. Both of the bottom disk drives connect to cell 0 through the core I/O for cell 0. The CD/DVD/DAT drive connects to cell 1 through the core I/O card for cell 1. If only one cell board is installed in the server, it must be installed into cell board slot 1 (bottom slot) of the server chassis. See Figure 1-2 on page 5.
2 Unpacking the Server Inspect shipping containers when the equipment arrives at the site. Check equipment after the packing has been removed. This chapter discusses how to inspect and receive the HP 9000 rp7420 server.
Unpacking the Server Inspecting the Server Cabinet Inspecting the Server Cabinet NOTE The server will ship in one of three different configurations. The configurations are: • on a pallet installed in a server cabinet • on a pallet for rack mount into an existing cabinet on the customer site • on a pallet with a wheel kit for installation as a stand-alone server HP shipping containers are designed to protect their contents under normal shipping conditions.
Unpacking the Server Receiving the Server Cabinet Receiving the Server Cabinet This section contains information about unpacking the cabinet. WARNING Wear protective glasses while cutting the plastic bands around the shipping container. These bands are under tension. When cut, they can spring back and cause serious eye injury. NOTE Position the pallet to allow for enough space to roll the cabinet off the pallet before unpacking. Remove the cabinet using the following procedure: Step 1.
Unpacking the Server Receiving the Server Cabinet Step 4. Remove the packing materials. CAUTION To reduce any ESD exposure, cut off the plastic wrapping around the cabinet. DO NOT pull it off the cabinet. Step 5. Remove the bolts that hold the ramps to the pallet, and remove the ramps. See Figure 2-2. NOTE Figure 2-2 shows one ramp attached to the pallet on either side of the cabinet with each ramp secured to the pallet using two bolts.
Unpacking the Server Receiving the Server Cabinet Step 6. Remove the six bolts from the base attaching the rack to the pallet. See Figure 2-3 Figure 2-3 Preparing to Roll Off the Pallet WARNING Use caution when rolling the cabinet off the ramp. A single 2-cell server in the cabinet weighs approximately 220 lb. To avoid a safety hazard, be sure the leveling feet on the cabinet are raised before you roll the cabinet down the ramp, and any time you roll the cabinet on the casters.
Unpacking the Server Receiving the Server Cabinet Securing the Cabinet When in position, secure and stabilize the cabinet, using the leveling feet at the corners of the base. Follow the instructions in rack documentation to install the anti-tip mechanisms on the bottom front and rear of the rack.
Unpacking the Server Stand Alone and To Be Racked Systems Stand Alone and To Be Racked Systems The following instructions explain how to configure stand-alone or to be racked systems. Rack Mount System Installation There are several documents written to help with rack mounting the server. This list is intended to guide the HP Installation Specialist to the documentation that has been written by the Rack Solutions team. The external website is http://h18004.www1.hp.
Unpacking the Server Manual Lifting Manual Lifting Use this procedure only if a HP approved lift is not available. This procedure should only be performed by two qualified HP Service Personnel utilizing proper lifting techniques and procedures. System damage can occur through improper removal and re-installation of devices. This task must be performed by trained personnel only.
Unpacking the Server Manual Lifting Step 6. Insert the pins of the panel into the rear of the front rack mount flange of the chassis. See Figure 2-5. (Cell boards are shown installed in figure.
Unpacking the Server Manual Lifting Step 7. Pull the spring plunger out and move the handles apart. Install the shoulder washer end of the panel into the keyways at the rear of the server chassis. See Figure 2-6. (Cell boards shown installed in figure.) Figure 2-6 Inserting the Shoulder Washer Pins Into the Server Chassis Step 8. Continue to pull the handles apart until the spring plunger snaps into the locked position. The spring plunger will drop down into the recess position.
Unpacking the Server Manual Lifting Step 9. Ensure that the handles are secure by pressing the handles together and moving back and forth. Figure 2-7 Lift Handles Mounted Step 10. Repeat steps 4 through 9 to install handle panel on the opposite side of server. Step 11. To lift the server, two individuals may rotate the handles 90 degrees to the horizontal position and grasp. NOTE To ensure proper installation, refer to the “Installation Guide” of the HP J1530B Rack Integration Kit. Step 12.
Unpacking the Server Using the RonI Model 17000 SP 400 Lifting Device Using the RonI Model 17000 SP 400 Lifting Device A lifter designed by the RonI company is available to rack-mount the server. The lifter can raise 400 lb. to a height of five feet. The lifter can be broken down into several components. When completely broken down, no single component weighs more than 25 lb. The ability to break the lifter down makes it easy to transport from the office to the car and then to the customer site.
Unpacking the Server Using the RonI Model 17000 SP 400 Lifting Device Step 1. Obtain the HP J1530B Rack Integration Kit Installation Guide before proceeding with the rack-mount procedure. This guide covers these important steps: • Installing the anti-tip stabilizer kit (A5540A) • Installing the ballast kit (J1479A) • Installing the barrel nuts on the front and rear columns • Installing the slides Step 2.
Unpacking the Server Using the RonI Model 17000 SP 400 Lifting Device Step 4. Remove the two foam cushions for lift access as shown in Figure 2-10. Figure 2-10 Remove Cushions for Lift Access Clearance for RonI lift is 28” x 5” Remove Cushions Step 5. Carefully position the lifter forks under the server until lift is against side of server. Step 6. Slowly raise the server off the pallet until it clears the pallet cushions.
Unpacking the Server Using the RonI Model 17000 SP 400 Lifting Device WARNING Do not raise server higher than necessary when moving. Figure 2-11 Raising a Server Off the Pallet Step 7. Roll the lifter and server away from the pallet. Step 8. Follow the HP J1530B Rack Integration Installation Guide to complete these steps: Chapter 2 • Mounting the server to the slides.
Unpacking the Server Wheel Kit Installation Wheel Kit Installation Compare the packing list with the contents of the wheel kit before beginning the installation.
Unpacking the Server Wheel Kit Installation Step 1. Cut and remove the polystrap bands securing the server to the pallet. Step 2. Lift the cardboard top from the cardboard tray resting on the pallet. Step 3. Remove the bezel kit carton and the top cushions from the pallet. Figure 2-12Component Locations Top Cushions Bezel Kit Cardboard Tray Step 4. Unfold bottom cardboard tray.
Unpacking the Server Wheel Kit Installation Step 5. Carefully tilt the server and place one of the foam blocks (A6093-44002) under the left side of the server. Do not remove any other cushions until instructed to do so. Figure 2-13Left Foam Block Position Foam Block Cardboard Tray Step 6. Carefully tilt the server and place the other foam block provided in the kit under the right side of the server.
Unpacking the Server Wheel Kit Installation Step 7. Remove the cushions from the lower front and rear of the server. Do not disturb the side cushions. Figure 2-15Foam Block Removal Step 8. Locate and identify the caster assemblies. Use the following table to identify the casters. NOTE Table 2-2 Caster The caster part number is stamped on the caster mounting plate.
Unpacking the Server Wheel Kit Installation Step 9. Locate and remove one of the four screws from the plastic pouch. Attach a front caster to the server. Figure 2-16Attaching a Caster to the Server Front Casters Step 10. Attach the remaining casters to the server using the screws supplied in the plastic pouch. Step 11. Remove the foam blocks from the left and right side of the server. Step 12. Locate the plywood ramp. Step 13.
Unpacking the Server Wheel Kit Installation Step 16. Insert the slot on the caster cover into the front caster. Secure the cover to the server by tightening the captive screw on the cover at the rear of the server. Figure 2-17 Securing Each Caster Cover to the Server Right Caster Cover Rear Casters Front Casters Left Caster Cover Step 17. Install the front bezel. Chapter 2 • Locate and mount the 4 plastic spring clips on front corners of chassis. • Orient the bezel onto the front of the server.
Unpacking the Server Wheel Kit Installation Step 18. Wheel kit installation is complete when both caster covers are attached to the server, all covers are installed and the front bezel is mounted.
3 Installing Accessories The following options may be installed in the HP 9000 rp7420 server: • additional hard disk drive storage • removable media device storage • PCI and PCI-X I/O cards Chapter 3 33
Installing Accessories Installing Add-On Products Installing Add-On Products This section provides information on installation of additional products that may have been ordered after server installation. Embedded Mass Storage When hard disks are installed, the top two hard disk drives are controlled by cell 1 through its assigned MP/SCSI Core I/O card. The bottom two hard disk drives are controlled by cell 0 through its assigned MP/SCSI Core I/O card.
Installing Accessories Installing Add-On Products Hard Disk Drive Installation The disk drives are located in the front of the chassis. The hard disk drives are hot-plug drives. CAUTION Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD safety precautions could result in damage to the HP 9000 rp7420 server. Step 1. Be sure the front locking latch is open, then position the disk drive in the chassis. Step 2.
Installing Accessories PCI/PCI-X Card Cage Assembly I/O Cards PCI/PCI-X Card Cage Assembly I/O Cards A number of PCI and PCI-X I/O cards are supported in the HP 9000 rp7420 Server. Known cards supported at the release of this manual are shown in Table 3-1.
Installing Accessories PCI/PCI-X Card Cage Assembly I/O Cards Table 3-1 HP 9000 rp7420 Server I/O Cards (Continued) Part Number Card Description Number of Cards Supported (B - Bootable) A7173A 2 port U320 SCSI 15B J3525A 2-port serial (X25/FR/SDLC) 15 J3526A 4-port serial (X25/FR) 15 Z7340A 8-port ACC 16 A4800A FWD SCSI 15B A4926A Gigabit Ethernet (1000B-SX) 15 A4929A Gigabit Ethernet (1000B-T) 15 A5158A Fibre Channel PCI Adapter 15B A6092A Hyperfabric (PCI 4X) 4 A9782A PCI
Installing Accessories PCI/PCI-X Card Cage Assembly I/O Cards If OLAR reports that a slot is present and powered off, but no OLAR operations to turn power on to that slot have succeeded even after the MRL is closed, the MRL may have been left open during boot. To clear this condition, close the MRL for the PCI slot then power off the PCI slot using the rad -o command. This will allow future OLAR operations to succeed on this PCI slot.
Installing Accessories PCI/PCI-X Card Cage Assembly I/O Cards Step 1. Remove the top cover. Step 2. Remove the PCI bulkhead filler panel. Step 3. Lever open the Manual Retention Latch for selected slot. Refer to Figure 3-2. Step 4. Install the I/O card in the slot. NOTE A slow, firm pressure is needed to properly seat the card into the backplane. Step 5. Flip the Manual Release Latch for the card slot to the closed position.
Installing Accessories PCI/PCI-X Card Cage Assembly I/O Cards The critical resource analysis (CRA) performed while doing an attention button initiated add action is very restrictive and the action will not complete–it will fail–to protect critical resources from being impacted. For finer control over CRA actions use pdweb or the olrad command. Refer to the Interface Card OL* Support Guide located on the Web at http://docs.hp.com for details. Step 9. Replace the top cover. Step 10.
4 Cabling and Power Up After the system has been unpacked and moved into position, it must be connected to an AC power source. The AC power must be checked for the proper voltage before the system is powered up. This chapter describes these activities.
Cabling and Power Up Voltage Check Voltage Check This section provides voltage check information for use on the customer site. The emphasis focuses on measuring the voltages at the power cord plug end specified as an IEC 320 C19 type plug. This end plugs directly into the back of the HP 9000 rp7420 Server chassis. NOTE These procedures must be performed for each power cord that will be plugged directly into the back of the HP 9000 rp7420 Server.
Cabling and Power Up Voltage Check Voltage Range Verification of Receptacle This measures the voltage between L1 and L2, L1 to ground, and L2 to ground. Three separate measurements are performed during this procedure. See Figure 4-1 for voltage reference points when performing the following measurements. Figure 4-1 Voltage Reference Points for IEC 320 C19 Plug IMPORTANT These measurements must be performed for every power cord that plugs into the HP 9000 rp7420 Server. Step 1.
Cabling and Power Up Voltage Check Safety Ground Verification (Single Power Source) This procedure measures the voltage level between A0 and A1. The voltage level between B0 and B1 will also be verified. All measurements will be taken between ground pins. See Figure 4-2 for ground reference points when performing these measurements. Figure 4-2 Safety Ground Reference Check—Single Power Source Step 1 V GND L1 GND L2 L1 L2 A1 A0 Step 2 V GND L1 GND L2 B0 L1 L2 B1 Step 1.
Cabling and Power Up Voltage Check Safety Ground Verification (Dual Power Source) This procedure measures the voltage level between A0 and A1, between B0 and B1, between A0 and B0, and between A1 and B1. All measurements will be taken between ground pins. See Figure 4-3 for ground reference points when performing these measurements. Figure 4-3 Safety Ground Reference Check—Dual Power Source Step 1 V GND GND L1 L2 L1 A0 L2 A1 Step 2 Step 3 V V Step 4 V GND L1 GND L2 B0 L1 L2 B1 Step 1.
Cabling and Power Up Voltage Check (Additional Procedure) Voltage Check (Additional Procedure) The voltage check ensures that all phases (and neutral, for international systems) are connected correctly to the cabinet and that the AC input voltage is within limits. This procedure must be performed if the previous voltage check procedure did not yield the expected results as previously outlined.
Cabling and Power Up Voltage Check (Additional Procedure) WARNING Do not set site AC circuit breakers serving the processor cabinets to ON before verifying that the cabinet has been wired into the site AC power supply correctly. Failure to do so might result in injury to personnel or damage to equipment when AC power is applied to the cabinet. Step 9. Set the site power circuit breaker to ON. WARNING SHOCK HAZARD Risk of shock hazard while testing primary power. Use properly insulated probes.
Cabling and Power Up Connecting AC Input Power Connecting AC Input Power The server can receive AC input power from two different AC power sources. If two separate power sources are available as depicted in Figure 4-6 on page 49, the server can be plugged into the separate power sources, increasing system reliability should one power source fail. The main power source is defined to be A0 and B0. The redundant power source is defined to be A1 and B1. See Figure 4-5 for the AC power input label scheme.
Cabling and Power Up Connecting AC Input Power Select Option: Figure 4-6 Power Source versus. Power Distribution BPS 0 A0* Power Source A BPS 1 A1* B0* B1* Power Source B *180-269 VAC WARNING Voltage is present at various locations within the server whenever a power source is connected. This voltage is present even when the main power switch is in the OFF position. To completely remove power, all power cords must be removed from the server.
Cabling and Power Up MP/SCSI Core I/O Connections MP/SCSI Core I/O Connections Each HP 9000 rp7420 Server can have up to two core I/O board sets installed, which allows two partitions to operate, or MP/SCSI Core I/O redundancy in a single partition configuration. Each core I/O board set consists of two boards: the MP/SCSI Core I/O board and the LAN/SCSI board. The MP/SCSI Core I/O board is oriented vertically and accessed from the back of the server.
Cabling and Power Up Setting Up the Customer Engineer Tool (PC) Setting Up the Customer Engineer Tool (PC) The Customer Engineer (CE) Tool is usually a laptop. It allows communication with the MP in the HP 9000 rp7420 Server. The MP monitors the activity of either a one partition or a multiple-partition configuration.
Cabling and Power Up Setting Up the Customer Engineer Tool (PC) If the CE Tool is a laptop using Reflection 1, ensure communications settings are in place, using the following procedure: 1. From the Reflection 1 Main screen, pull down the Connection menu and select Connection Setup. • Select Serial Port. • Select Com1 • Check the settings and change, if required. Go to More Settings to set Xon/Xoff. Click OK to close the More Settings window. • Click OK to close the Connection Setup window. 2.
Cabling and Power Up Turning on Housekeeping Power and Logging in to the MP Turning on Housekeeping Power and Logging in to the MP After connecting the serial device, log in to the Management Processor (MP). +3.3 V DC Housekeeping power (HKP) (also known as standby power) is active as soon as AC power is applied to the server. As the MP uses housekeeping power, it is possible to log in to the MP even with the power switch in the OFF position. The power switch is a DC power switch that controls +48 V DC.
Cabling and Power Up Turning on Housekeeping Power and Logging in to the MP The MP Main Menu is displayed: Figure 4-7 MP Main Menu 54 Chapter 4
Cabling and Power Up Configuring LAN Information for the MP Configuring LAN Information for the MP This section describes how to set and verify the server MP LAN port information. LAN information includes the MP network name, the MP IP address, the subnet mask, and gateway address. This information is provided by the customer. To set the MP LAN IP address: Step 1. At the MP Main Menu prompt (MP>), enter cm. to enter the MP Command Menu. Step 2.
Cabling and Power Up Configuring LAN Information for the MP Step 6. Confirm the new address. Step 7. Enter the MP Hostname. This is the host name for the MP LAN. The name can be as many as 64 characters in length, and include alphanumeric characters, - (dash), _ (under bar), . (period), or a space. HP recommends that the name be a derivative of the complex name. For example, Acme.com_MP. Step 8. Enter the LAN parameters for the Subnet mask and Gateway address fields.
Cabling and Power Up Accessing the Management Processor via a Web Browser Accessing the Management Processor via a Web Browser Web browser access is an embedded feature of the MP/SCSI Core I/O card. The Web browser allows access to the server through the LAN port on the core I/O card. Initial MP configuration must be done from the local console connected to the Local RS232 port. NOTE The MP/SCSI Core I/O card has a separate LAN port from the system LAN port.
Cabling and Power Up Accessing the Management Processor via a Web Browser Step 7. Launch a Web browser on the same subnet using the IP address for the MP LAN port. Figure 4-11 Browser Window Zoom In/Out Title Bar Step 8. Select the emulation type you want to use. Step 9. Click anywhere on the Zoom In/Out title bar to generate a full screen MP window. Step 10. Login to the MP when the login window appears. Access to the MP via a Web browser is now possible.
Cabling and Power Up Verifying Presence of the Cell Boards Verifying Presence of the Cell Boards To perform this activity, either connect to the MP using a console, or connect the CE Tool (laptop) to the RS-232 Local port on the MP/SCSI Core I/O. After logging in to the MP, verify that the MP detects the presence of all the cells installed in the cabinet. It is important for the MP to detect the cell boards. If it does not, the partitions will not boot. To determine if the MP detects the cell boards: 1.
Cabling and Power Up Booting the HP 9000 rp7420 Server Booting the HP 9000 rp7420 Server Powering on the server can be accomplished by either pressing the power switch on the front panel or by using the PE command to power up the cabinet or complex at the MP command menu (MP:CM>). If only a serial console is available to the system, monitor the system as it boots.
Cabling and Power Up Booting the HP 9000 rp7420 Server Selecting a Boot Partition using the Management Processor At this point in the installation process, the hardware is set up, the MP is connected to the LAN, the AC and DC power have been turned on, and the self test is completed. Now the configuration can be verified. After the DC powers on and the self test is complete, use the MP to select a boot partition. 1. From the MP Main Menu, enter cm. 2. From the MP Command Menu, enter bo. 3.
Cabling and Power Up Adding Processors with Instant Capacity On Demand Adding Processors with Instant Capacity On Demand The Instant Capacity On Demand (iCOD) program provides access to additional CPU resources beyond the amount that was purchased for the server. This provides the ability to activate additional CPU power for unexpected growth and unexpected spikes in workloads. Internally, iCOD systems physically have more CPUs, called iCOD CPUs, than the number of CPUs actually purchased.
Cabling and Power Up Using the Checklist Using the Checklist The following checklist is an installation aid and should be used only after you have installed several systems using the detailed procedures described in the body of this manual.
Cabling and Power Up Using the Checklist Table 4-2 Factory-Integrated Installation Checklist (Continued) (Continued) PROCEDURE IN-PROCESS Initials Comments COMPLETED Initials Comments Unpack other equipment Remove and dispose of packaging material Move cabinet(s) and equipment to computer room Install non-factory, integrated I/O cards (if required) Move cabinets into final position Position cabinets next to each other (approximately 1/2 inch) Adjust leveling feet Install anti-tip plates Inspect cabl
Cabling and Power Up Using the Checklist Table 4-2 Factory-Integrated Installation Checklist (Continued) (Continued) PROCEDURE IN-PROCESS Initials Comments COMPLETED Initials Comments Verify remote link (if required) Select PCI card slot Install PCI card Verify installation Route cables using the cable management arm Install other peripherals (if required) Perform visual inspection and complete installation Set up network services (if required) Enable iCOD (if available) Final inspection of circuit
Cabling and Power Up Using the Checklist 66 Chapter 4
Index A ac power voltage check, 46 AC power receptacles, 6 B backplane mass storage, 10 PCI, 7, 9 system, 9 booting HP-UX, 61 BPS (Bulk Power Supply), 53 bulk power supply, 4 C cell board, 4, 5, 51, 59 verifying presence, 59 checklist installation, 63 cm (Command Menu) command, 59 co (Console) command, 60 commands cm (Command Menu), 59 co (Console), 60 CTRL-B, 60 di (Display), 61 du (display MP bus topology), 59 vfp (Virtual Front Panel), 60 D di (Display) command, 61 disk internal, 10, 50 du (display MP bu
Index U unpacking inspecting for damage, 12 V verifying system configuration, 61 voltage check, 46 68
