Datasheet
Management page. Under Power Cords, click on the "HP Power Cord Matrix" link.
That link will list cable descriptions, requirements, and specifications for UPS and PDU
units. Please see the following link:
www.hp.com/products/powercords
.
HP Rack Series
HP Rack SeriesHP Rack Series
HP Rack Series
HP Rack 10000 G2 Series
HP Rack 10000 G2 SeriesHP Rack 10000 G2 Series
HP Rack 10000 G2 Series
(Carbon/Graphite Metallic)
HP 10642 G2 Pallet Universal Rack
AF001A
HP 10642 G2 Shock Universal Rack
AF002A
HP 10642 G2 1200mm deep Shock Rack
AF092A
HP 10647 G2 1200mm deep Shock Rack
AF094A
NOTE:
NOTE:NOTE:
NOTE:
It is mandatory to use a shock pallet when shipping racks with equipment
installed.
NOTE:
NOTE:NOTE:
NOTE:
Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12402_div/12402_div.html
(Worldwide)
NOTE:
NOTE:NOTE:
NOTE:
For additional information regarding Rack Cabinets, please see the following
URL:
http://www.hp.com/go/rackandpower
.
NOTE:
NOTE:NOTE:
NOTE:
The increasing power of new high-performance processor technology requires
increased cooling efficiency for rack-mounted servers. The 10000 G2 Series Racks
provide enhanced airflow for maximum cooling, allowing these racks to be fully
loaded with servers using the latest processors.
CAUTION:
CAUTION:CAUTION:
CAUTION:
If a third-party rack is used, observe the following additional requirements
to ensure adequate airflow and to prevent damage to the equipment: Front and rear
doors: If your 42U server rack includes closing front and rear doors, you must allow
830 square inches (5,350 sq cm) of hole evenly distributed from top to bottom to
permit adequate airflow (equivalent to the required 64 percent open area for
ventilation). Side: The clearance between the installed rack component and the side
panels of the rack must be a minimum of 2.75 inches (7 cm).
CAUTION:
CAUTION:CAUTION:
CAUTION:
Always use blanking panels to fill all remaining empty front panel U-
spaces in the rack. This arrangement ensures proper airflow. Using a rack without
blanking panels results in improper cooling that can lead to thermal damage.
NOTE:
NOTE: NOTE:
NOTE:
For additional information, refer to the Setup and Installation Guide or the
Documentation CD provided with the server, or to the server documentation located
in the Support section at the following URL: www.hp.com/servers/dl380.NOTE: Quick
deploy rail system provides tool-free support for racks with square or round mounting
holes (including Compaq/HP 7000, 9000, 10000 G2 and HP series), with an
adjustment range of 24" - 36". The ambidextrous cable management arm can be
mounted on either the left or right side for improved cable management.
NOTE:
NOTE: NOTE:
NOTE:
High Airflow Inserts (High Air Flow Rack Door Insert for the 7142 Rack (single)
- PN: 327281-B21; or High Air Flow Rack Door Insert for the 7142 Rack (6-pack) -
PN: 327281-B22) are required to support the HP ProLiant DL380 in 7000 series
racks. The DL380 Cable Management Arm is not supported on 7000 series racks.
NOTE:
NOTE: NOTE:
NOTE:
Cable management arm must be removed to access hot-plug power supplies
when the cable management arm is mounted on the right.
HP Rack Options
HP Rack OptionsHP Rack Options
HP Rack Options
Keyboards and Monitors
Keyboards and MonitorsKeyboards and Monitors
Keyboards and Monitors
HP TFT7600 G2 KVM Console Rackmount Keyboard US Monitor
AZ870A
HP TFT7600 G2 KVM Console Rackmount Keyboard UK Monitor
AZ871A
QuickSpecs
HP ProLiant DL380 Generation 6 (G6)
HP ProLiant DL380 Generation 6 (G6)HP ProLiant DL380 Generation 6 (G6)
HP ProLiant DL380 Generation 6 (G6)
Additional Options
DA - 13234 Worldwide — Version 44 — October 14, 2011
Page 38