HP ProBook 470 G1 Notebook PC Maintenance and Service Guide
© Copyright 2013 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel and Core are trademarks or registered trademarks of Intel Corporation in the United States and other countries. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. SD Logo is a trademark of its proprietor.
Important Notice about Customer Self-Repair Parts CAUTION: Your computer includes Customer Self-Repair parts and parts that should only be accessed by an authorized service provider. See Chapter 5, "Removal and replacement procedures for Customer Self-Repair parts," for details. Accessing parts described in Chapter 6, "Removal and replacement procedures for Authorized Service Provider only parts," can damage the computer or void your warranty.
iv Important Notice about Customer Self-Repair Parts
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
vi Safety warning notice
Table of contents 1 Product description ........................................................................................................................................... 1 2 External component identification ..................................................................................................................... 6 Display .................................................................................................................................................. 6 Top .............
Equipment guidelines ....................................................................... 32 5 Removal and replacement procedures for Customer Self-Repair parts ......................................................... 33 Component replacement procedures ................................................................................................. 33 Battery ............................................................................................................................... 34 Service door .
Enhanced snap feature ...................................................................................................... 83 Discovering and connecting to Miracast-compatible wireless displays (select models only) ................................................................................................................................... 83 Opening to the Windows desktop instead of the Start screen ........................................... 83 This PC ..............................................
Using System Diagnostics .................................................................................................................. 97 10 Computer Setup (BIOS) and Advanced System Diagnostics in SUSE Linux ............................................... 98 Starting Computer Setup .................................................................................................................... 98 Using Computer Setup ..................................................................................
Blu-ray ROM DVD±RW SuperMulti DL Drive ................................................................................... 118 DVD-ROM drive ............................................................................................................................... 118 Specification information in Device Manager ................................................................................... 119 15 Statement of Volatility ................................................................................
xii
1 Product description Category Description Product Name HP ProBook 470 G1 Notebook PC Processors Intel® Core™ i7 processor, Quad Core, 3rd generation (6-MB L3 cache, 35W) 4702MQ, 2.20-GHz processor Intel® Core i5 processors, Dual Core, 3rd generation (3-MB L3 cache, 37W) 4200M, 2.50-GHz processor Intel Core i3 processors, Dual Core, 3rd generation (3-MB L3 cache, 37W) 4100M, 2.50-GHz processor 4000M, 2.40-GHz processor Intel Pentium processor, Dual Core (2-MB L3 cache, 37W) 3550M, 2.
Category Description Customer-accessible Supports the following drives: Fixed optical drives ● 1-TB, 5400-rpm ● 750-GB, 5400-rpm ● 500-GB, 7200-rpm, ● 500-GB, 5400-rpm, hybrid (8-GB SSD) MLC ● 320-GB, 5400-rpm Supports the following 9.
Category Description Ports Audio-in (stereo microphone) Audio-out (stereo headphone) RJ-45 (Ethernet, includes link and activity lights) USB 3.0 (2) USB 2.0 (2) VGA (Dsub 15-pin) supporting 1920 × 1200 external resolution at 60-GHz (hot plug/ unplug with auto-detect) HDMI 1.
Category Description Win 8.1 Multi-language (ML) 64-bit Win 8.1 Professional 64-bit Novell™: SuSE Linux™ – SLED 11, 64-bit, SP2 FreeDOS 2.0 Restore Media (DRDVD/SRDVD): DRDVD Windows 8.
Category Description Hard drive Memory module Optical drive WLAN module Keyboard 5
2 External component identification Display NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) WLAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) Internal microphones (2) (select models only) Record sound. (3) Webcam light (select models only) On: The webcam is in use. (4) Webcam (select models only) Records video and captures still photographs.
Top TouchPad Component Description (1) TouchPad on/off button Turns the TouchPad on and off. (2) TouchPad zone Moves the pointer and selects or activates items on the screen. (3) Left TouchPad button Functions like the left button on an external mouse. (4) Right TouchPad button Functions like the right button on an external mouse.
Lights NOTE: Your computer may look slightly different from the illustration in this section. Component (1) Description Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state (Windows) or Suspend state (Linux). NOTE: The elapsed time between blinks is longer than on previous models. ● (2) Microphone mute light Amber: Microphone is off. (3) Num lock light On: Num lock is on.
Buttons and fingerprint reader (select models only) NOTE: Your computer may look slightly different from the illustration in this section. Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state/Suspend, press the button briefly to exit Sleep/Suspend.
Component Description (3) Wireless button Turns the wireless feature on or off but does not establish a wireless connection. (4) Volume mute button Mutes and restores speaker sound. (5) Fingerprint reader (select models only) Allows a fingerprint logon instead of a password logon. Keys NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description esc key Displays system information when pressed in combination with the fn key. NOTE: Not applicable to SLED.
Front Component (1) (2) Description Hard drive light Media Card Reader ● Blinking white: The hard drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive. Reads data from and writes data to memory sticks and digital memory cards such as Secure Digital (SD).
Left Component Description (1) Power connector Connects an AC adapter. (2) AC adapter/Battery light ● White: The computer is connected to external power and the battery is charged from 90 to 99 percent. ● Amber: The computer is connected to external power and the battery is charged from 0 to 89 percent. ● Blinking amber: A battery that is the only available power source has reached a low battery level. When the battery reaches a critical battery level, the battery light begins blinking rapidly.
Right Component (1) Description Audio-out (headphone) jack Produces sound when connected to optional powered stereo speakers, headphones, earbuds, a headset, or television audio. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety, and Environmental Notices.
Bottom Component (1) Description Battery and service door release latches ● Releases the battery from the battery bay by sliding the release latches one time. ● When the battery has been removed from the battery bay, releases the service door from the computer by sliding the release latches a second time. (2) Battery bay Holds the battery. (3) Service door Provides access to the hard drive bay, the wireless LAN (WLAN) module slot, the WWAN module slot, and the memory module slots.
Component Description NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. Service tag and PCID label Service tag When ordering parts or requesting information, provide the computer serial number and model description provided on the service tag. ● Product name (1). This is the product name affixed to the front of the computer. ● Serial number (s/n) (2).
PCID label The PCID label provides the information required to properly reset the notebook firmware (BIOS) back to factory shipped specifications when replacing the system board. The label may have a different number of characters depending on the operating system on the computer. NOTE: Computer details may vary from images.
3 Illustrated parts catalog Computer major components NOTE: Details about your computer, including model, serial number, product key, and length of warranty, are on the service tag at the bottom of your computer. See Service tag and PCID label on page 15 for details.
Item Description Spare part number (1) Display panel, 43.9-cm (17.3-inch), HD+, anti-glare, with webcam 723643-001 (2) Keyboard (includes cable) NOTE: For a detailed list of available keyboards, see Sequential part number listing on page 24.
Item Description Spare part number 4000M, 2.4-GHz processor with 3-MB L3 cache (includes thermal grease) 737327-001 Intel Pentium processor, Dual Core 3550M, 2.4-GHz, with 2-MB L3 cache 737329-001 Intel Celeron processor 2950M, 2.1-GHz, with 2-MB L3 cache 737326-001 (13) Hard drive extension board 725891-001 (14) Optical drive extension board 723675-001 (15) Fan/heat sink assembly (includes replacement thermal material) 721937-001 (16) Battery, Li-ion (17) 9-cell (93 WHr, 2.
Item Description (22) Service door Spare part number Service door 723648-001 RCTO 747994-001 Display components Item Description Spare part number (1) Display bezel 723640-001 (2) Display panel (raw) not spared (3) Display/webcam cable assembly 723646-001 (in Cable Kit) (4) 20 Webcam module for use in all models 721543-001 Display Hinge Kit 723642-001 Chapter 3 Illustrated parts catalog
Item Description Spare part number (5) Display hinges (left and right) (6) Display hinge covers (7) Antennas 723641-001 (8) Display rear covers 723639-001 Plastics Kit Item (1) Description Spare part number Plastics Kit 723647-001 Optical drive protective insert Cable Kit Item Description Spare part number Cable Kit 723646-001 (1) Display/webcam cable (2) USB/audio board connector cable (3) Battery connector cable (4) Card reader cable Plastics Kit 21
Item Description (5) Power connector cable (6) Function board connector cable (7) Power button board cable Spare part number Mass storage devices Description (1) (2) 22 Spare part number Hard drives 1-GB, 5400-rpm 676521-001 750-GB, 5400-rpm 634250-001 500-GB, 7200-rpm 703267-001 500-GB, 5400-rpm 683802-001 500-GB, 5400-rpm, hybrid (8-GB SSD) 732000-001 320-GB, 5400-rpm 634953-001 Hard Drive Hardware Kit (includes hard drive bracket and screws; not illustrated) 721519-001 Optical
Miscellaneous parts Description Spare part number AC adapters 90-W AC adapter 693712-001 90-W AC adapter for use in India and the People’s Republic of China 693713-001 Power cords: For use in Australia 490371-011 For use in Denmark 490371-081 For use in Europe, the Middle East, and Africa 490371-021 For use in India 490371-D61 For use in Israel 490371-BB1 For use in Italy 490371-061 For use in the People’s Republic of China 490371-AA1 For use in South Africa 490371-AR1 For use in South
Sequential part number listing CSR flag designations: A = Mandatory B = Optional C = Service technician recommended N = Non-user replaceable 24 Spare part number CSR flag Description 434594-001 A HP USB optical travel mouse 490371-001 A Power cord for use in North America 490371-011 A Power cord for use in Australia 490371-021 A Power cord for use in Europe, the Middle East, and Africa 490371-031 A Power cord for use in the United Kingdom 490371-061 A Power cord for use in Italy 49037
Spare part number CSR flag Description 693374-001 A 8-GB memory module (PC3L-12800, 1600-MHz, DDR3L) 693712-001 A 90-W AC adapter 693713-001 A 90-W AC adapter for use in India and the People’s Republic of China 703267-001 A 500-GB, 7200-rpm hard drive 703888-001 A Case, slim top load 708457-001 A 6-cell, 47 WHr, 2.2 Ah Li-ion battery 708458-001 A 9-cell, 93 WHr, 2.8 Ah Li-ion battery 709848-001 A Realtek RTL8188EE 802.11bgn Wi-Fi Adapter 710418-001 A Mediatek MT7630E 802.
26 Spare part number CSR flag Description 721953-291 A Keyboard for use in Japan 721953-A41 A Keyboard for use in Belgium 721953-AB1 A Keyboard for use in Taiwan 721953-AD1 A Keyboard for use in South Korea 721953-B31 A Keyboard for use in the Netherlands and Europe 721953-B71 A Keyboard for use in Sweden and Finland 721953-BA1 A Keyboard for use in Slovenia 721953-BB1 A Keyboard for use in Israel 721953-BG1 A Keyboard for use in Switzerland 721953-D61 A Keyboard for use in
Spare part number CSR flag Description 725889-001 A DVD-ROM drive (includes bezel, bracket, and screws) 725890-001 A DVD±RW SuperMulti DL Drive (includes bezel, bracket, and screws) 725891-001 B Hard drive connector 732000-001 A 500-GB, 5400-rpm, hybrid (8-GB SSD) hard drive 734083-001 N System board for use in models without Windows 8 with 1-GB discrete graphics (includes thermal material) 734083-501 N System board for use in Windows 8 Standard models with 1-GB discrete graphics (includ
4 Removal and replacement procedures preliminary requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Phillips P0 and P1 screwdrivers ● Torx T8 screwdriver Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.
Cables and connectors CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables.
Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.
Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations. ● Place items on a grounded surface before removing items from their containers.
Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
5 Removal and replacement procedures for Customer Self-Repair parts CAUTION: The Customer Self-Repair program is not available in all locations. Installing a part not supported by the Customer Self-Repair program may void your warranty. Check your warranty to determine if Customer Self-Repair is supported in your location. Component replacement procedures NOTE: Please read and follow the procedures described here to access and replace Customer SelfRepair parts successfully.
Battery Description Spare part number 9-cell, 93 WHr, 2.8 Ah Li-ion battery 708458-001 6-cell, 47 WHr, 2.2 Ah Li-ion battery 708457-001 Before removing the battery, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Service door Remove the service door to access the memory module slot, hard drive, and other components. Before removing the service door, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Using the optional security screw Use the optional security screw to lock the service door to the bottom of the computer. When not in use the security screw can be stored inside the battery bay. To use the security screw: 1. Remove the battery (see Battery on page 34). 2. Remove the security screw from inside the battery bay (1) and insert it (2) to lock the service door in place.
4. Remove the battery (see Battery on page 34). 5. Remove the service door (see Service door on page 35). To remove a hard drive: 1. Turn the computer upside down on a flat surface. 2. Remove the 4 Phillips PM2.5×3.0 screws from the hard drive. 3. Pull the hard drive tab (1) toward the side of the computer to disconnect the hard drive. 4. Lift the hard drive (2) out of the hard drive bay.
5. To remove the hard drive from the hard drive cover, remove the 4 Phillips PM3.0×4.0 screws (1) that secure the cover to the drive, and then lift the cover straight up and off the hard drive (2). Reverse this procedure to install a hard drive.
Optical drive NOTE: All optical drive spare part kits include an optical drive bezel, bracket, and screws. Description Spare part number Blu-ray ROM DVD±RW SuperMulti DL Drive 723671-001 DVD±RW SuperMulti DL Drive 725890-001 DVD-ROM drive 725889-001 Before removing the optical drive, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
4. Remove the optical drive (3) from the computer. 5. To remove the bracket from the optical drive, remove the Phillips PM2.0×3.0 screw (1) that secures the bracket to the drive, and then remove the bracket from the drive (2). Reverse this procedure to install an optical drive.
Memory modules NOTE: Primary and expansion memory is installed in a stacked configuration in the bottom of the computer. If only one memory module is installed, it must be installed in the bottom socket. Description Spare part number 2-GB (PC3L-12800, 1600-MHz, DDR3L) 691739-001 4-GB (PC3L-12800, 1600-MHz, DDR3L) 691740–001 8-GB (PC3L-12800, 1600-MHz, DDR3L) 693374-001 Update BIOS before adding memory modules Before adding new memory, make sure you update the computer to the latest BIOS.
3. Remove the memory module (2) by pulling the module away from the slot at an angle. NOTE: Memory modules are designed with a notch to prevent incorrect insertion into the memory module slot. NOTE: The computer uses two memory sockets. The top socket houses the expansion memory module and the bottom socket houses the primary memory module. The removal procedure is the same for both memory sockets. Reverse this procedure to install a memory module.
WLAN/Bluetooth combo card The computer uses a card that provides both WLAN and Bluetooth functionality. Description Spare part number Mediatek MT7630E 802.11bgn 1x1 Wi-Fi + BT4.0 Combo Adapter 710418-001 Atheros AR9485 802.11b/g/n 1x1 WiFi Adapter 675794-001 Atheros AR9565 802.11bgn 1x1 WiFi + BT4.0 combo Adapter 690019-001 Intel Dual Band Wireless-AC 3160 802.11 a/b/g/n/ac (1x1) WiFi with Bluetooth 4.0 combo 710662-001 Realtek RTL8188EE 802.
4. Remove the WLAN module (3) by pulling the module away from the slot at an angle. NOTE: WLAN modules are designed with a notch to prevent incorrect insertion. NOTE: If the WLAN antennas are not connected to the terminals on the WLAN module, the protective sleeves must be installed on the antenna connectors, as shown in the following illustration. Reverse this procedure to install the WLAN module.
Keyboard NOTE: For a detailed list of available keyboards, see Sequential part number listing on page 24. Description Spare part number Keyboard 721953-xxx Before removing the keyboard, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
5. Lift the top of the keyboard up at an angle (2). NOTE: Make sure not to prematurely pull the keyboard cable out of the system board connector. 6. Rotate the keyboard until it rests on the palm rest (1), and then disconnect the keyboard cable by lifting the keyboard connector latch (2), and then disconnecting the keyboard cable from the system board (3). 7. Remove the keyboard. Reverse this procedure to install the keyboard.
6 Removal and replacement procedures for Authorized Service Provider parts CAUTION: Components described in this chapter should only be accessed by an authorized service provider. Accessing these parts can damage the computer or void the warranty. Component replacement procedures NOTE: Details about your computer, including model, serial number, product key, and length of warranty, are on the service tag at the bottom of your computer. See Service tag and PCID label on page 15 for details.
Remove the top cover: 1. Position the computer upside-down with the front toward you. 2. Remove the following covers and screws that secure the top cover to the computer: NOTE: Rubber screw covers come in three different sizes and are available in the Rubber Kit, spare part number 723672-001. (1) 2 rubber screw covers from the rear corners (2) 2 rubber screw covers from each side (3) 2 rubber screw covers from the front corners (4) 6 Torx T8M2.5×6.0 screws from under each screw cover 3.
4. Remove the following screws: (1) 2 Phillips PM2.0×3.0 screws from the optical drive bay (2) 5 Phillips PM2.5×3.0 screws from the battery bay 5. Position the computer upright and open it as far as possible. 6. Remove the 4 Torx T8M2.5×6.0 screws from the top of the computer. 7.
8. ● (3): Function board cable ● (4): Card reader cable Pry the top cover off the computer to disengage it. NOTE: Begin by attempting to pry the top cover loose near the optical drive. 9. Lift the top of the top cover (1), and the lift the top cover up slightly (2) to gain access to the connected audio/USB cable and connector underneath. CAUTION: To avoid damage to the cable and connector, make sure not to disconnect the cable when you lift the top cover from the computer. 10.
(2): Power button board cable (3): USB/audio board cable (4): Card reader cable Reverse this procedure to install the top cover.
Fingerprint reader assembly Description Spare part number Fingerprint reader assembly (includes cable, bracket, holder, and screws) 723670-001 Before removing the fingerprint reader assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Power button board Description Spare part number Power button board assembly 721531-001 Before removing the power button board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
When installing the power button board, insert the bottom of the board into the slot, and then rotate board down into place. If the cable is connected to the board, it blocks the view of the tab on the board and the slot it inserts into. Function board Description Spare part number Function board 721943-001 Before removing the function board, follow these steps: 1. Shut down the computer.
4. Turn the board upside down (3), and then disconnect the cable from the board (4). 5. Remove the function board from the top cover. Reverse this procedure to install the function board. Card reader board Description Spare part number Card reader board 734088-001 Before removing the card reader board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
NOTE: Before you remove the card reader, make sure nothing (memory card or plastic insert) in installed. 1. Position the top cover upside-down. 2. Disconnect the cable that routes to the touchpad buttons (1). 3. Disconnect the cable that routes to the system board (2). 4. Remove the two Phillips PM2.0×2.0 broadhead screws (3) that secure the card reader board to the computer. 5. Remove the card reader board from the top cover (4). Reverse this procedure to install the card reader board.
Speaker assembly Description Spare part number Speaker assembly 723674-001 NOTE: You must remove the left speaker to remove to function board cable. Before removing the speaker assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
5. Remove the speakers from the computer (4). Reverse this procedure to install the speaker assembly.
USB/audio board Description Spare part number USB/audio board 721542-001 Before removing the USB/audio board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
System board NOTE: All system board spare part kits include replacement thermal material.
Remove the system board: 1. Position the computer upright with the front toward you. 2. Disconnect the display cable (1) from the system board. 3. Disconnect the battery connector cable from the system board (2). 4. Remove the 2 Phillips PM2.5×4.0 screws (3) that secure the system board to the computer. 5. Remove the Phillips PM2.5×4.0 screw (3) that secures the optical drive extension board to the computer and the Phillips PM2.5×4.
Power cable The power cable is included in the Cable Kit, spare part number 723646-001. Before removing the power cable, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Battery cable The battery cable is included in the Cable Kit, spare part number 723646-001. Before removing the battery cable, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
RTC battery Description Spare part number RTC battery 683601-001 Before removing the RTC battery, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer. 4.
Optical drive extension board Description Spare part number Optical drive extension board 723675-001 Before removing the optical drive extension board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Hard drive extension board Description Spare part number Hard drive extension board 725891-001 Before removing the hard drive extension board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Fan/heat sink assembly All fan/heat sink assembly spare part kits include replacement thermal material. Description Spare part number Fan/heat sink assembly 721937-001 Before removing the fan/heat sink assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
4. Lift the fan/heat sink from the system board (8). NOTE: Thoroughly clean thermal material from the surfaces of the system board components (1)(3) and the heat sink (2)(4) each time you remove the heat sink. All heat sink and processor spare part kits include thermal material. Reverse this procedure to install the fan/heat sink assembly.
Processor NOTE: All processor spare part kits include replacement thermal material. Description Spare part number Intel Core i7 processor, Quad Core 4702MQ, 2.2-GHz processor with 6-MB L3 cache 723522-001 Intel Core i5 processors, Dual Core 4200M, 2.5-GHz processor with 3-MB L3 cache (includes thermal grease) 737328-001 Intel Core i3 processors, Dual Core 4100M, 2.5-GHz processor with 3-MB L3 cache (includes thermal grease) 737474-001 4000M, 2.
3. Lift the processor (2) straight up and remove it. NOTE: The gold triangle (3) on the processor must be aligned with the triangle embossed on the processor slot (4) when you install the processor. Reverse this procedure to install the processor.
Latch assembly NOTE: The latch kit is not spared. Before removing the latch assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer. 4.
4. Rotate the left side of the lever upward to remove the pin on the top cover (2) from the groove in the lever, and then lift the lever from the computer (3). To install the latch assembly, reverse the removal procedure.
Display assembly All display assemblies include WLAN antenna transceivers and cables. For a list of individual display spare parts, see Display components on page 20. Description Spare part number Display assembly, 43.9-cm (17.3-inch), HD+, anti-glare, with webcam 723643-001 Before removing the display assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
4. Place the computer upright and open as far as possible. 5. Remove the WLAN antennas from the tabs and the routing path (1) on the top of the computer. 6. Note the location that the antennas route through the chassis (2). 7. Remove the five Torx T8M2.5×4.0 screws (1) from the display hinges (3 screws in the left hinge, 2 in the right hinge). 8. Lift the display assembly straight up and remove it (2).
9. If you need to remove the hinge covers from the display hinges, squeeze and pull the covers straight up and off the display to remove them. If you need to remove the hinge covers from the display hinges, pinch the top and bottom of the hinges and then pull the hinges straight up and off the display. Display hinge covers are available in the Display Hinge Kit using spare part number 723642-001. 10. If you need to remove the display bezel, remove the 2 mylar screw covers (1) and the 2 Phillips PM2.5×4.
12. Remove the display bezel (6). The display bezel is available using spare part number 723640-001. Display bezel mylar screw covers are available in the Rubber Kit, spare part number 723672-001. 13. If it is necessary to replace the webcam module, disconnect the cable from the module (1), and then gently pull the module away from the double-sided tape on the display enclosure (2). The webcam module is available using spare part number 721543-001. 14.
15. Remove the display hinges and panel from the display enclosure (2). 16. Position the display panel and hinge assembly upright. 17. Remove the 3 Phillips PM1.5×2.0 screws (1) that secure each display hinge to the display panel. 18. Remove the display hinges (2).
19. If it is necessary to remove the display/webcam cable assembly, disconnect the display panel cable from the rear of the display panel by lifting the tape (1) that covers the connector, and disconnecting the cable from the panel (2). The display/webcam cable assembly is available in the Cable Kit, spare part number 723646-001. 20. Lift the display/webcam cable assembly straight up and off the display panel.
21. If it is necessary to remove the antennas from the display enclosure, remove the antennas from clips on each side of the enclosure (1), gently lift the transceivers (2) to disengage them from the double-stick tape, and then lift the antennas from the display enclosure. Antennas are available using spare part number 723641-001. Reverse this procedure to reassemble and install the display assembly.
7 New Windows 8.1 features This guide describes new Windows® features, which may update some of the information provided with your computer.
Action Using a keyboard and mouse Using touch gestures (1) Open an app Click a Start screen app. Tap a Start screen app. (2) Display the charms (Search, Share, Start, Devices, and Settings) Point to the upper-right or lower-right corner of the Start screen. Swipe from the right edge of the TouchPad or touch screen. (3) Find a list of all apps on your computer Point to the lower-left area of the Start screen, and then click the arrow.
Action Using a keyboard and mouse Using touch gestures 1. Point to the upper-right or lower-right corner of the screen to display the charms, and then click Settings. 1. 2. Click the Power icon, and then click Shut down. Swipe from the right edge of the TouchPad or touch screen to display the charms, and then tap Settings. 2. Tap the Power icon, and then tap Shut down.
Enhanced snap feature You can snap applications to the left or right side of the screen in order to view a Start screen app and a desktop app at the same time. Depending on the computer's screen resolution, you can snap up to four apps at the same time. ▲ Drag an app to the left or the right side of the screen.
Using Windows backup and restore For information about the Windows backup and restore features, see the HP Support Assistant. NOTE: The path to access the HP Support Assistant has changed. 1. From the Start screen, select the HP Support Assistant app. 2. Type restore in the Search field, and then follow the information provided. For additional backup information, type backup in the Search field.
Resource Contents Regulatory, Safety and Environmental Notices ● Important regulatory notices, including proper battery disposal information ● Specific warranty information about this computer To access this information: 1. On the Start screen, type support, and then select the HP Support Assistant app. 2. Select My computer, and then select User guides. Limited Warranty To access this information: 1. On the Start screen, type support, and then select the HP Support Assistant app. 2.
8 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) in Windows 8 Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory.
To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes: Click the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the tab key and the arrow keys to select Main > Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
Updating the BIOS Updated versions of the BIOS may be available on the HP website. Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs. Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file.
BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the download is complete. If no instructions are displayed, follow these steps: 1. From the Start screen, type e, and then select File Explorer. 2. Click your hard drive designation. The hard drive designation is typically Local Disk (C:). 3. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains the update. 4. Double-click the file that has an .
Setting a new boot order in Computer Setup To start Computer Setup and set a boot device order that the computer uses each time it is turned on or restarted, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3.
Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Entering MultiBoot Express preferences When the Express Boot menu is displayed during startup, you have the following choices: ● To specify a boot device from the Express Boot menu, select your preference within the allotted time, and then press enter.
4. Select your computer model, and then select your operating system. 5. In the Diagnostic section, click HP UEFI Support Environment. – or – Click Download, and then select Run.
9 Setup Utility (BIOS) and System Diagnostics in Windows 7 Using Setup Utility Setup Utility, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Setup Utility includes settings for the types of peripherals installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Setup Utility.
Navigating and selecting in Setup Utility To navigate and select in Setup Utility, follow these steps: 1. 2. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. ● To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or use a pointing device to click the item.
Restoring factory settings in Setup Utility NOTE: Restoring defaults will not change the hard drive mode. To return all settings in Setup Utility to the values that were set at the factory, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Setup Utility. 3. Use the arrow keys to select Exit > Load Setup Defaults. 4. Follow the on-screen instructions. 5.
Determining the BIOS version To determine whether available BIOS updates contain later BIOS versions than those currently installed on the computer, you need to know the version of the system BIOS currently installed. BIOS version information (also known as ROM date and System BIOS) can be displayed by pressing fn+esc (if you are already in Windows) or by using Setup Utility. 1. Start Setup Utility (BIOS). 2. Use the arrow keys to select Main. 3.
4. Double-click the file that has an .exe extension (for example, filename.exe). The BIOS installation begins. 5. Complete the installation by following the on-screen instructions. NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file from your hard drive. Using System Diagnostics System Diagnostics allows you to run diagnostic tests to determine if the computer hardware is functioning properly.
10 Computer Setup (BIOS) and Advanced System Diagnostics in SUSE Linux Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of peripherals installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter. – or – ● To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions.
BIOS version information (also known as ROM date and System BIOS) can be displayed as follows: 1. Start Computer Setup. 2. Use a pointing device or the arrow keys to select File > System Information. 3. To exit Computer Setup without saving your changes, click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter.
Using Advanced System Diagnostics Advanced System Diagnostics allows you to run diagnostic tests to determine if the computer hardware is functioning properly. The following diagnostic tests are available in Advanced System Diagnostics: ● Start-up test—This test analyzes the main computer components that are required to start the computer. ● Run-in test—This test repeats the start-up test and checks for intermittent problems that the start-up test does not detect.
11 Backup and recovery in Windows 8 To protect your information, use Windows backup and restore utilities to back up individual files and folders, back up your entire hard drive, create system repair media (select models only) by using the installed optical drive (select models only) or an optional external optical drive, or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. From the Start screen, type backup, click Settings, and then select from the list of displayed options. 2. Follow the on-screen instructions to set up your backup, create a system image (select models only), or create system repair media (select models only).
NOTE: For additional information on recovering information using the Windows tools, perform a search for these topics in HP Support Assistant. To access HP Support Assistant on the Start screen, select the HP Support Assistant app. Using f11 recovery tools CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files that you have created and any software that you have installed on the computer are permanently removed.
Using Windows Refresh for quick and easy recovery When your computer is not working properly and you need to regain system stability, the Windows Refresh option allows you to start fresh and keep what is important to you. IMPORTANT: Refresh removes any traditional applications that were not originally installed on the system at the factory. NOTE: During Refresh, a list of removed traditional applications will be saved so that you have a quick way to see what you might need to reinstall.
To use the Start screen: 1. On the Start screen, point to the far-right upper or lower corner of the screen to display the charms. 2. Click Settings. 3. Click Change PC settings in the bottom-right corner of the screen, and then select General from the PC settings screen. 4. Scroll the right-side choices down to display Remove everything and reinstall Windows. 5. Under Remove everything and reinstall Windows, select Get started, and follow the on-screen instructions.
12 Backup and recovery in Windows 7 To protect your information, use Windows Backup and Restore to back up individual files and folders, back up your entire hard drive (select models only), create system repair discs (select models only) with the installed optical drive (select models only) or an optional external optical drive, or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
Creating recovery media NOTE: Operating system recovery media can be created only once. Thereafter, the option to create that media will not be available. 1. Select Start > All Programs > Security and Protection > HP Recovery Disc Creator. 2. Select Driver DVD or Windows DVD. 3. From the drop-down menu, select the drive for burning the recovery media. 4. Click the Burn button to start the burning process.
Performing a system recovery In case of system failure or instability, the computer provides the following tools to recover your files: ● Windows recovery tools: You can use Windows Backup and Restore to recover information you have previously backed up. You can also use Windows Startup Repair to fix problems that might prevent Windows from starting correctly. ● f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image.
Using f11 recovery tools CAUTION: Using f11 recovery tools completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed. The f11 recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled. To recover the original hard drive image using f11: 1. If possible, back up all personal files. 2.
After the repair is completed: 1. Eject the Windows 7 operating system DVD, and then insert the Driver Recovery disc. 2. Install the Hardware Enabling Drivers first, and then install Recommended Applications.
13 Backup and Recovery in SUSE Linux Recovery after a system failure is as good as your most recent backup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. Backing up your information You should back up your computer files on a regular schedule to maintain a current backup. You can manually back up your information to an optional external drive, a network drive, or discs.
also restore the computer to its factory condition from the HP dedicated recovery partition on the hard drive. CAUTION: Using Recovery completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed. The recovery tool reinstalls the original operating system and HP programs and drivers that were installed at the factory. Software, drivers, and updates not installed by HP must be manually reinstalled.
14 Specifications Computer specifications Metric U.S. Length 28.0 cm 11.0 in Width 41.4 cm 16.3 in Height (front to rear) 2.5 to 3.2 cm 1.0 to 1.2 in Equipped with optical drive, 1 DIMM, hard drive, WLAN module, webcam, 6 cell battery 3.00 kg 6.61 lbs Equipped with no optical drive, 1 DIMM, hard drive, WLAN module, webcam, 6 cell battery 2.87 kg 6.33 lbs Dimensions Weight Input power Operating voltage 19.0 V dc @ 4.74 A – 90 W or 18.5 V dc @ 3.5 A - 65 W Operating current 4.74 A or 3.
Metric Nonoperating U.S. 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range of temperatures. 43.9-cm (17.3-in), HD+ display specifications Metric U.S. Active diagonal size 43.9-cm 17.3-in Resolution 1600x900 (HD+) Active area 382.08x214.
Hard drive specifications 750-GB* 500-GB* 320-GB* Height 9.5 mm 9.5 mm 9.5 mm Width 70 mm 70 mm 70 mm Weight 115 g 101 g 101 g Interface type SATA SATA SATA Transfer rate 100 MB/sec 100 MB/sec 100 MB/sec Security ATA security ATA security ATA security Single track 1.
DVD±RW SuperMulti DL Drive specifications Applicable disc Center hole diameter Read: Write: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CDROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video CD), Multisession CD (Photo-CD, CD-EXTRA, Portfolio, CD-R, CD-RW), CD-R, CD-RW, DVDROM (DVD-5, DVD-9, DVD-10, DVD-18), DVDR, DVD-RW, DVD+R, DVD+RW, DVD-RAM CD-R and CD-RW DVD+R, DVD+RW, DVD-R, DVDRW, DVD-RAM 1.5 cm (0.59 in) Disc diameter Standard disc 12 cm (4.72 in) Mini disc 8 cm (3.
Blu-ray ROM DVD±RW SuperMulti DL Drive Applicable disc Read: Write: CD-DA, CD+(E)G, CD-MIDI, CDTEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video CD), Multisession CD (Photo-CD, CD-EXTRA, Portfolio, CD-R, CD-RW), CD-R, CD-RW, DVDROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, HDROM (Single Layer), HD-ROM (Dual Layer), HD DVD-R, HD DVD-R for Dual Layer, HD DVD-RW CD-R and CD-RW DVD+R, DVD+R(9), DVD+RW, DVD-R, DVD-R(9),DVD-RW, DVD-RAM Access time CD DV
Standard disc 12 cm (4.72 in) Mini disc 8 cm (3.15 in) Disc thickness 1.2 mm (0.047 in) Track pitch 0.74 μm Access time CD DVD Random < 100 ms < 125 ms Full Stroke < 175 ms < 225 ms Audio output level Line-out, 0.7 Vrms Cache buffer 512 KB Data transfer rate CD-R (24X) 3600 KB/s (150 KB/s at 1X CD rate) CD-RW (10X) 1500 KB/s (150 KB/s at 1X CD rate) CD-ROM (24X) 3,600 KB/sec DVD (8X) 3600 KB/s (150 KB/s at 1X CD rate) Multiword DMA mode 2 16.
15 Statement of Volatility The purpose of this document is to provide general information regarding non-volatile memory in industry-standards based HP Business Notebook PC systems and provide general instructions for restoring nonvolatile memory that can contain personal data after the system has been powered off and the hard drive has been removed. HP Business Notebook PC products that use Intel®-based or AMD®-based system boards contain volatile DDR memory.
i. Reboot the system. If the system has a Trusted Platform Module (TPM) and/or fingerprint sensor, one or two prompts will appear. One to clear the TPM and the other to Reset Fingerprint Sensor; press F1 to accept or F2 to reject. If the HP notebook model includes Intel® Centrino with VPro™, reboot the PC and enter BIOS Setup by pressing F10 when prompted. Select System Configuration, then AMT Options. Then select Unconfigure AMT on next boot. Select Save then Yes.
HP Sure Start Select Intel-based 2013 HP Business Notebook PCs offer HP Sure Start, which provides hardwarebased assurance of the following: ● HP-approved firmware is running on the HP Embedded Controller (EC) – EC Options in BIOS found under “BIOS Integrity Checking” ● An HP-approved BIOS is running on the host processor HP Sure Start verifies the integrity of critical, non-executable platform data residing in the main flash and provides selfhealing mechanisms to restore any code or critical platform d
Non-volatile memory usage Non Volatile Memory Type Amount (Size) Does this memory store customer data? Does this memory retain data when power is removed? What is the purpose of this memory? How is data input into this memory? How is this memory write protected? Real Time Clock (RTC) battery backed-up CMOS configuration memory (CMOS) 256 Bytes No Yes Stores system date and time and limited keyboard controller data. Using the F10 Setup utility or changing the Microsoft® Windows® date & time.
(present only in models ending in a ‘p’ or ‘w’ or with Intel Centrino Pro technology) Provisioning Data and iAMT third party data store. firmware update utility. Unique Provisioning Data can be entered at the factory or by an administrator using the Management Engine (MEBx) setup utility. The third party data store contents can populated by a remote management console or local applications registered by an administrator to have access to the space. write access to this area.
Questions and answers 1. 2. How can the BIOS settings be restored (returned to factory settings)? a. Turn on or restart the computer and press F10 when prompted near the bottom of the display. b. Select File, then select Restore defaults. c. Follow the on-screen instructions. d. Select File, save changes and exit, then press Enter.
16 Power cord set requirements The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts ac, or from 220 to 240 volts ac. The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased. Power cord sets for use in other countries and regions must meet the requirements of the country or region where the computer is used.
Country/region Accredited agency Applicable note number Japan JIS 3 The Netherlands KEMA 1 New Zealand SANZ 1 Norway NEMKO 1 The People's Republic of China CCC 4 Saudi Arabia SASO 7 Singapore PSB 1 South Africa SABS 1 South Korea KTL 5 Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 6 Thailand TISI 1 The United Kingdom ASTA 1 The United States UL 2 1. The flexible cord must be Type HO5VV-F, 3-conductor, 0.75mm2 conductor size.
17 Recycling Battery When a non-rechargeable or rechargeable battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for battery disposal. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, see the HP Web site at http:// www.hp.com/recycle. Display WARNING! The backlight contains mercury.
Perform the following steps to disassemble the display assembly: 1. Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. 2. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly. 3. Remove the display bezel (3).
4. Disconnect all display panel cables (1) from the display inverter and remove the inverter (2). 5. Remove all screws (1) that secure the display panel assembly to the display enclosure. 6. Remove the display panel assembly (2) from the display enclosure. 7. Position the display panel assembly upside-down. 8. Remove all screws that secure the display panel frame to the display panel. 9.
10. Remove the display panel frame (2) from the display panel. 11. Remove the screws (1) that secure the backlight cover to the display panel. 12. Lift the top edge of the backlight cover (2) and swing it outward. 13. Remove the backlight cover. 14. Position the display panel right-side up. 15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Position the display panel upside-down. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. 17. Remove the backlight frame from the display panel. 18. Remove the backlight from the backlight frame. 19. Disconnect the display panel cable (1) from the LCD panel. 20. Remove the screws (2) that secure the LCD panel to the display rear panel. 21.
22. Release the tape (4) that secures the LCD panel to the display rear panel. 23. Remove the LCD panel. 24. Recycle the LCD panel and backlight.
Index A AC adapter, spare part numbers 23, 25 AC adapter/battery light 12 antennas disconnecting 43 spare part number 21, 26 apps closing 82 displaying all 82 snapping 83 audio board spare part number 25 audio, product description 2 audio-in (microphone) jack, identifying 13 audio-out (headphone) jack, identifying 13 B backup 112 Backup and Restore 102 base enclosure, spare part number 19 battery spare part number 19, 25, 34 battery and service door release latches 14 battery cable removal 63 spare part num
fingerprint reader assembly removal 52 spare part number 18, 26, 52 fingerprint reader, identifying 10 fn key, identifying 10 function board removal 54 spare part number 18, 25, 54 function board cable illustrated 22 function keys, identifying 10 G graphics, product description grounding equipment and methods 32 1 H hard drive precautions 29 product description 1 removing 36 spare part numbers 19, 22, 24, 25, 36 specifications 116 hard drive connector spare part number 27 hard drive extension board remova
power button, identifying 9 power cable removal 62 spare part number 62 power connector cable, illustrated 22 power connector, identifying 12 power cord set requirements 126 spare part numbers 23, 24 power lights 8 power requirements, product description 3 processor product description 1 removal 69 spare part numbers 18, 69 product description audio 2 chipset 1 display panel 1 Ethernet 2 external media cards 2 graphics 1 hard drives 1 keyboard 3 memory module 1 microphone 2 operating system 3 optical drives
Windows button, identifying 10 wireless antennas disconnecting 43 wireless displays, connecting 83 wireless light 8 wireless, product description 2 WLAN antennas, identifying 6 WLAN/Bluetooth combo card removal 43 spare part number 19, 43 workstation guidelines 31
