Service Manual HP OmniBook 300, 425, 430, 530
Notice In a continuing effort to improve the quality of our products, technical and environmental information in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Table of Contents Table of Figures .........................................................................................................................iv Introduction .................................................................................................................................v Product Overview........................................................................................................................1 Product Features ......................................................
Appendix D - Part Numbers.......................................................................................................
Table of Figures Figure 1 - OmniBook 300, 425, and 430 Features .......................................................................2 Figure 2 - OmniBook 530 Features..............................................................................................3 Figure 3 - Serial Loop Back Connector ......................................................................................11 Figure 4 - Parallel Loop Back Connector ................................................................................
Introduction This document provides reference information for the HP OmniBook 300, HP OmniBook 425, HP OmniBook 430, and HP OmniBook 530. It is intended to be used by HP-qualified service personnel to help with the installation, servicing, and repair of these HP OmniBook PCs. It is a self-paced guide designed to train you to install, configure, and repair the OmniBook Notebook PC. You can follow it without having any equipment available.
Part 1 Product Overview • Product Features • Product Comparisons • Product at a Glance
Product Features OmniBook 300, 425, and 430 Figure 1 - OmniBook 300, 425, and 430 Features 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 2 Latch Display Keyboard Card slot A Card-eject levers On/Off key Mouse Mouse-eject button Display contrast buttons Speaker 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
OmniBook 530 Figure 2 - OmniBook 530 Features 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Latch Display Keyboard Card slots Card-eject levers On/Off key Mouse Mouse-eject button Display contrast buttons Speaker AC adapter socket 12. 13. 14. 15. 16. 17. 18. 19. 20. 21.
Product Comparisons Size Closed Weight Processor Clock Speed Display VGA-out Support Battery OmniBook 300 OmniBook 425 OmniBook 430 OmniBook 530 16.3 x 28.2 x 3.6 cm (6.4 x 11.1 x 1.4 in) 1.31 kg (2.888 lb) w/flash 1.36 kg (2.998) w/hdd 386SXLV 20 MHz 640 x 480 VGA 9-inch diagonal LCD 16 shades of gray none 16.3 x 28.2 x 3.6 cm (6.4 x 11.1 x 1.4 in) 1.31 kg (2.888 lb) w/flash 1.36 kg (2.998) w/hdd 486SLC/e 25 MHz 640 x 480 VGA 9-inch diagonal LCD 16 shades of gray none 16.3 x 28.2 x 3.6 cm (6.4 x 11.
Pre-installed Software OmniBook 300 OmniBook 425 OmniBook 430 OmniBook 530 the flash disk version One slot available with the hard disk version © MS Windows 3.1* © MS DOS 5.0* MS Word 2.0* MS Excel 4.0* LapLink Remote ™ Access Phone Book Appointment Book HP Financial Calculator the flash disk version One slot available with the hard disk version © MS Windows 3.1* © MS DOS 5.0* MS Word 2.0* MS Excel 4.
Product at a Glance 14 28 14 29 27 17 32 35 11 13 16 33 16 5 10 6 2 1 9 18 2 1 1 1 2 2 15 13 7 2 2 13 24 2 12 2 2 26 5 2 30 2 23 13 4 3 6 19 20 8 2 31 21 22 34 25 6 10
Description Part Number OB300 OB425 OB430 OB530 Standoff 0380-4060 Screw M2x4.
Part 2 Troubleshooting • OmniBook Self Test • Troubleshooting Flowchart
OmniBook Self-Test The OmniBook Self-Test provides on-board hardware and firmware diagnostics. To operate the self-test, perform the following steps: 1. 2. 3. 4. 5. Save all files and close all applications: The OmniBook is reset at the end of the self-test. Turn the OmniBook OFF. Press and hold the [Esc] key and press [ON]. You will hear a short three-tone beep. Self Test will initialize and start. To run a test: Highlight the test name and press [ENTER].
Figure 3 - Serial Loop Back Connector Figure 4 - Parallel Loop Back Connector 11
Troubleshooting Flowchart The following series of flowcharts is intended as a guide for troubleshooting the OmniBook 300, 425, 430, and 530. Each technician should still rely on personal experience and supplemental knowledge when diagnosing a problem. These tips should be kept in mind when referencing the troubleshooting flowcharts: • • • 12 Use the Main Troubleshooting Flowchart to isolate the problem to a particular area.
Main Troubleshooting Flowchart START No See Hard Disk flowchart No See Memory flowchart See DOS or Windows? Get user information: Name Telephone number Unit serial number Repair history Yes Memory OK? (No memory errors) Yes Eliminate all obvious physical problems? No Isolate damage.
Main Troubleshooting Flowchart (continued) A Parallel port operates correctly? No See Parallel Port flowchart Yes Serial port operates correctly? No See Serial Port flowchart Yes External VGA operates correctly? No See Serial Port flowchart Yes PCMCIA cards operate correctly? Infrared port operates correctly? Yes 14 No See PCMCIA flowchart No See IR flowchart If you still have a problem, it's in software or in a part of the unit not covered by these flowcharts.
Power Source Problems Start: No power lamp, or low battery life Yes Battery in Omnibook? No Turn Omnibook off Remove and reinsert battery Yes HP ac adapter and cable? Connect OB to ac adapter, plug adapter into wall socket No Done Turn on Omnibook Yes Light on continuously (not intermittent)? See power light? No Try different power socket B A 15
Power Source Problems (continued) A Yes B Light on continuously (not intermittent)? Try different power socket No Recheck cables, connections: ac adapter to Yes Ambient temperature within specification? Yes No No Yes Light still intermittent? No Done: Power source problem Done Done: Bring temperature within specifications Done: Suspect bad ac adapter, cable, or connector Ensure power coming from wall socket Ensure battery installed correctly Go to Power Management Problems flowchart C 16
Power Source Problems (continued) C Can you substitute known good ac adapter? Yes Yes See steady power light? No No Yes Done: Original ac adapter or cable bad Can you substitute known good OB? Yes Yes Done: Suspect original OB base unit bad See steady power light? No Ac adapter warm? No No Done: Suspect bad ac adapter or cable 17
Boot-Up Problems Start: Problems during bootup Press Ctrl Alt Del to get a clean boot Multiple beeps Hear single or multiple beeps during boot? Single beeps Yes See Windows or DOS prompt in display? Done Yes Yes OB support utility disk available? No No OB support utility disk available? No Suspect software problem: locate OB support utility disk and call back Insert OB support utility disk and reboot Yes Done 18 See prompt to enter time and date? No Done: Suspect bad Omnibook base unit
Display Problems Start: Power light on, but no display Physical inspection of display Adjust brightness and contrast controls Yes Done See anything in display? No Go to Boot-Up Problems flowchart 19
Hard Disk Problems Start: Hard disk fails to boot up to DOS or Windows; or other hard disk problems See anything in drive C:? Yes Yes Yes Noisy? No HP hard disk? No No Insert hard disk in C: Done Speech: Need hard disk to boot correctly Yes See "Nonsystem disk"? No Done: Hard disk bad Done Suspect corrupt files on hard disk Insert hard disk containing system files Boot from OB companion disk in drive A: Done Do SCANDISK C: Yes A 20 Soft checking OK? No B
Hard Disk Problems (continued) A B Do hard checking. Save logs. Let SCANDISK repair errors. Do hard checking. Save logs. Let SCANDISK repair errors.
Hard Disk Problems (continued) C Remove disk from drive A: Boot from drive C: Yes DOS and Windows boot OK? No Give customer general data recovery hints Done Yes Is customer willing to reformat hard disk? No Boot from drive A: Done: Customer must purchase another hard disk Back up hard disk to A: Reformat hard disk Reload image Done 22
Memory Problems Start: Problem with plug-in memory Yes No Intermittent problem? End current session.
Memory Problems (continued) A Power up OB (memory module removed) Yes Memory problem disappears? No Run short OB memory self-test (without memory module) Done: Suspect bad memory module Yes Memory self-test OK? No Run long OB memory self-test (without memory module) Yes Done: Suspect memory module bad 24 Memory self-test OK? No Done: Suspect OB base unit bad
Power Management Problems Start: Low battery life Yes Physical inspection: HP battery? Contacts dirty? Physically OK? Done: Suspect software problem Yes Yes Ac adapter attached to OB and wall? No See OB power icon? No Is Windows running? No Start Windows Attach ac adapter Yes Yes Has unit recharged sufficiently? OB Power icon in Control Panel? No Yes Power Mgmnt icon in OB Tools? Recharge sufficiently Yes Yes Power on during recharge? No 1-1/2 hours per charge? No No Speech: Standard
Power Management Problems (continued) A Yes Yes Ambient temperature in spec? "Bad/no battery" message? Yes Ensure ac adapter plugged into OB and wall No Charging circuitry may be defective No Yes "Bad/no battery" message? Done: Replace battery or use OB on ac power only PCMCIA cards installed? No Yes Speech: PCMCIA cards can use power even when not on No Speech: DOS games, TSR's, other software can reduce battery life Remove PCMCIA cards, recharge battery Yes Get 1-1/2 hours battery lif
Power Management Problems (continued) B Yes No Get 1-1/2 hours battery life? Use MSD to determine what TSR's are running Done Disable TSR's Yes Done Get 1-1/2 hours battery life? No Done: Suspect bad or old battery 27
Pop-Out Mouse Problems Start: OB popout mouse problem Eliminate obvious physical problems Yes See Windows? No Start Windows running Yes Is mouse OB popout mouse? No Disable other mouse Enable OB popout mouse Yes Yes A 28 See mouse pointer? No Done: Suspect software problem (Windows problem) Does mouse pointer move? B
Pop-Out Mouse Problems (continued) A Yes Reaches all 4 corners of screen? Yes Yes Is mouse jittery, intermittent? No Can you calibrate mouse? No No Done: Mouse should be OK Suspect bad mouse C 29
Pop-Out Mouse Problems (continued) B Suspect software configuration problem Yes Setup shows correct mouse driver? No Check for correct OB mouse driver Configure Setup for correct OB mouse driver Yes Mouse driver OK? No Look at mouse in Windows Control Panel Yes Mouse moves? No Done: Replace with known good version of correct OB mouse driver Yes See OB punch button? Done: Mouse OK No Set Control Panel for OB punch button mouse Suspect bad mouse Yes OB mouse works OK? No Done Exit Windows
Pop-Out Mouse Problems (continued) C Run OB diagnostic program Yes Yes OB mouse operates correctly? No Suspect mouse works in known good OB? Yes Does mouse pass all tests? Boot normally to Windows Can you put suspect mouse in known good OB? Yes Clean boot: Ctrl Alt Del, press F5 when starting No Put known good OB mouse in suspect base unit No Remove mouse from OB base unit, examine mouse, and reinsert Yes Known good mouse works? No No Suspect bad mouse.
Floppy Drive Problems Start: External floppy disk drive problem External FDD is HP device? Yes Yes Cable is correct one? No No Done Locate and attach correct cable Eliminate obvious physical problems: Cable OK? Pins not bent? Cable connected and solidly in connectors? Yes Drive works OK? Done Yes Yes A 32 Has drive ever worked? Inserts, ejects known good disk cleanly? No No B Done: Suspect bad or damaged drive No
Floppy Drive Problems (continued) A Clean boot: Ctrl Alt Del, press F5 during boot Yes Drive works OK? No Done Run short selftest twice Yes With original OB turned on, connect good drive and cable Can you swap with known good drive and cable? No Yes Suspect software problem (proceed to B) Yes Good drive works OK? Original drive works OK? Suspect software problem No Done: Suspect bad drive No With known good OB turned on, connect original drive and cable Yes Drive passes self-test OK? Wit
Floppy Drive Problems (continued) B Clean boot: Ctrl Alt Del, press F5 during boot Yes Run OB disk self-test: Put empty, known good disk, formatted for DOS, in drive. Press Enter.
Parallel Port Problems Start: Problem with parallel port Use PRN command to print a file Yes No Problem with Laplink Remote? Yes Prints file OK? No Other printer available? No Troubleshoot Laplink Remote Done: Parallel port OK Yes Physical inspection: Cable connected? Cable pins OK? Attach OB and use PRN command to print file on different printer Clean boot: Ctrl Alt Del, press F5 during boot Yes Exit to DOS See Windows? Yes No Done: Suspect bad printer or cable Prints file OK? No Run OB
Parallel Port Problems (continued) A Yes Self-test OK? Reconfirm: Printer plugged in? On? On line? Done: Bad OB base unit Attach printer to desktop PC Clean boot to DOS on desktop PC: Ctrl Alt Del, press F5 during boot Yes Done: Suspect original OB bad 36 PRN prints file OK? No No Done: Suspect bad printer or cable
Serial Port Problems Start: Problem with serial port Yes Problem with Laplink Remote? No Troubleshoot Laplink Remote Install loopback connector Physical inspection: Cable connected? Bent pins? Cable appears OK? Run OB self-test procedure Yes Self-test OK? Connected to what? Modem? Printer? Other? No Done: Serial port OK Yes Done: Suspect bad serial port in OB base unit Loopback connector available? No A 37
Serial Port Problems (continued) A Ensure proper default serial port configuration Yes No Serial port works OK? Done Yes Can you eliminate all potential software conflicts? No Eliminate software conflicts Yes No Serial port works OK? Done Yes Done: Suspect original device or cable bad 38 Plug another device and cable into serial ports Serial port works OK? No Done: Suspect bad OB base unit serial port
PCMCIA Problems Start: PCMCIA card problem Determine type of card Yes Known issue with this card? No Seek additional information on card Yes Yes Has card ever worked? Has any software been loaded or modified since card worked? No No Remove card (with power on or off) Visually inspect card: Connectors bent? Damaged? Wet? Suspect software configuration problem Yes Inspection reveals problems? No Reinsert card Done: Suspect bad PCMCIA card B A 39
PCMCIA Problems (continued) A B Clean boot: Ctrl Alt Del, press F5 during boot Press Ctrl Alt Del Run OB self-test Yes Yes Self-test OK? See Windows display? No Exit to DOS prompt Yes See DOS prompt? Suspect bad card Done: Return card to HP HP card? No Done: Contact card vendor Remove card and run CARDINFO Interpret CARDINFO results C 40 No Exit to DOS prompt Done: Software configuration or setup problem Yes No
PCMCIA Problems (continued) C Yes No Hardware problem? Done: Suspect bad OB base unit Yes Check CONFIG.SYS and AUTOEXEC.
PCMCIA Problems (continued) D Yes Hardware problem in one slot only? Done: Suspect bad OB base unit No Yes Software problem in both slots? Yes Seek further information consult with Technical Support 42 Done: Suspect software configuration problem No Software problem in one slot only? No Done
IR Port Problems Start: Problem with infrared (IR) port Yes Problem with Laplink Remote? Clean boot: Ctrl Alt Del, press F5 during boot No Troubleshoot Laplink Remote Run OB self-test Physical inspection: IR port not covered? Painted over? Obscured? Run IR self-test in proper environment Yes Ensure operating distance within specification (1 meter or less) IR self-test OK? Done: Suspect software problem No Move OB to different desk, room Run IR self-test in proper environment Ensure operating
Part 3 Hardware Repair • Battery • Memory • Hard Disk Drive/Flash Card and System ROM • Mouse • Small Parts • Display • Keyboard • Logic PCA Board • Paw Carrier • Other Components CAUTION: Always provide proper grounding when performing any of the following repairs.
Battery (End User Replaceable) All of the monochrome OmniBook models use the same HP Nickel-Metal-Hydride (NiMH) Battery Pack, part number F1045A (service replacement part number F1045-60901). However, for some models, 1.5 V AA batteries can be used in place of the NiMH battery pack. The following table lists all of the monochrome OmniBooks and the batteries that can be used safely in each model.
Replacement Procedure 1. To replace the battery, do one of the following: • To replace the OmniBook battery pack, insert the rounded side of the pack into the compartment first. It is not possible to fully insert the battery pack incorrectly. • To replace AA batteries, orient them as shown by the symbols in the battery compartment. 2. Replace and latch the battery cover.
Memory (End User Replaceable) The OmniBook 530 uses a unique memory module that is not compatible with the OmniBook 300, 425, or 430. The table below summarizes the compatibility of the memory modules for each OmniBook model.
Required Equipment • Probe (or similar device) for the OmniBook 300, 425, and 430 only CAUTION: To avoid damage due to electrostatic discharge, handle the memory module by the edges only. Removal Procedure 1. Remove the battery and ac adapter from the OmniBook. 2. Slide the memory door off (see below illustration). Figure 6 - Removing the Memory Module 3.
Hard Disk Drive/Flash Card and System ROM (End User Replaceable) The Hard Disk Drives for the OmniBook 300, 425, 430, and 530 can be reimaged if necessary. If the software is corrupted, or otherwise damaged, on the hard drive, it can be reformatted and the software reloaded. Also, if the hard drive fails and must be replaced, a blank hard drive can be ordered and the appropriate software loaded. The below procedures indicate the proper actions necessary for reloading software on each OmniBook model.
Required Equipment • none Removal Procedure 1. Exit all applications, including Windows. 2. Turn the OmniBook off and remove the battery and ac adapter. 3. Turn the OmniBook over, release the two latches on the bottom of the tray, and pull out the tray. See below illustration. Figure 7 - Removing Card Slot Tray 4. Lift the Hard Disk, Flash Card, or System ROM out of the tray. Replacement Procedure 1. Reverse the above steps to replace the Hard Disk, Flash Card, or System ROM. 2.
Mouse (End User Replaceable) Required Equipment • none Removal Procedure 1. Press the mouse-eject button to eject the mouse. 2. Pull the mouse firmly away from the OmniBook (see below illustration). The entire mouse assembly will pull free. Figure 8 - Removing the Mouse Replacement Procedure 1. Place the end of the mouse “stick” into the mouse housing. 2. Slide the mouse into the slot and firmly push the mouse until it is completely flush with the side of the OmniBook.
Small Parts (End User Replaceable) The following small parts are all end user replaceable. Battery Door Push the two battery door latches away from the battery door. Remove the battery door by lifting up at the notch in the bottom case. Place the battery door, tab side first, over the battery compartment. Slide the two battery latches in place to secure the door. Battery Door Latch Once the battery door is removed (see above), the battery door latches will slide out of the bottom case.
Display (HP Authorized Service Providers Only) Required Equipment • Appropriate ESD station • Torx #6 screwdriver • 5mm Hexdriver • Two small flat tip screwdrivers (or similar prying devices) • Probe Removal Procedure 1. Remove the battery, ac adapter, mass storage, system card (if applicable), memory module (if installed), modem (if installed), mouse, and any installed PCMCIA accessory cards. 2. Remove the four Rubber Feet and seven Screws from the bottom case (see below illustration).
3. Remove the I/O Door and the four standoffs located on the I/O backplane (see figure below). Figure 10 - Backplane Standoffs 4. Two flat tip screwdrivers, or similar prying devices, are needed to remove the Top Case and Display Assemblies. Four plastic tabs hold the Top Case and Bottom Case together. Two tabs are located in each PCMCIA slot (see below illustration). Note, the screws seen in the PCMCIA slot do not need to be removed.
Place a prying device at a tab location between the metal and plastic of the Bottom Case (see figure below, left). Place another prying device in the PCMCIA eject button (see figure below, right). To release the tab, simultaneously twist prying device A while lifting on prying device B. Use caution with this maneuver, as the plastic tabs can break off the Bottom Case. If this occurs, the Bottom Case must be replaced. Prying device “A” Prying device “B” Figure 12 - Bottom Case Prying Locations 5.
8. With the separation increased slightly, the display cable can be disconnected using a probe. Use caution to keep the OmniBook on a level surface. With the Top Case partially separated, small internal parts may dislodge when the OmniBook is tilted at a sharp angle. Place the probe at the base of the display cable connector between the two rows of pins. Use a rocking motion to lift the cable from the connector. See the below illustration for proper placement of the probe.
Figure 15 - Keyboard Flex Cables 10. To separate the Keyboard from the Display, five grounding eyelets must be removed from the display posts (see below illustration). Use caution when removing the grounding eyelets, as they can be broken off easily. If this happens, the assembly must be replaced. To prevent the eyelets from breaking, bend the grounding eyelet tabs at the farthest point from the eyelet.
11. To remove the Display from the Top Case, the display cable and two grounding cables must be guided through the holes in the Top Case. Replacement Procedure 1. Guide the display posts, display cable and two grounding cables on the Display through the holes in the Top Case. 2. Replace the grounding eyelets over the display posts (see Figure 16). Use caution when replacing the grounding eyelets, as they can be broken off easily. If this happens, the assembly must be replaced. 3.
5. To reconnect the display cable, position a probe in the cable as shown in the below illustration. Figure 17 - Display Cable Probe Position 6. Use the probe to connect the display cable into the connector as shown below. Use caution to keep the OmniBook on a level surface. With the Top Case partially separated, small internal parts may dislodge when the OmniBook is tilted at a sharp angle. Figure 18 - Reconnecting Display Cable 7.
Acceptable to reassemble All eyelets are present. Figure 19 - I/O Port Eyelets (all present) Acceptable to reassemble There are two matched sets and at least one eyelet in each position. Figure 20 - I/O Port Eyelets (two matched sets) Not acceptable to reassemble There is only one matched set. Figure 21 - I/O Port Eyelets (only one matched set) Not acceptable to reassemble There are two matched set, but no eyelet in position one. Figure 22 - I/O Port Eyelets (no eyelet in position one) 8.
Keyboard (HP Authorized Service Providers Only) Required Equipment • Appropriate ESD station • Torx #6 screwdriver • Two small flat tip screwdrivers (or similar prying devices) • Probe Removal Procedure 1. Follow the Display Removal Procedure to separate the Display and Top Case from the Bottom Case. 2. Once the Display is removed, the Keyboard must now be separated from the Top Case. Hold the Top Case and Keyboard Assembly exactly as shown in the below illustration.
Logic PCA Board (HP Authorized Service Providers Only) Required Equipment • Appropriate ESD station • Torx #6 screwdriver • Two small flat tip screwdrivers (or similar prying devices) • Probe Removal Procedure 1. Follow the Display Removal Procedure to separate the Display and Top Case Assembly from the Bottom Case. 2. Remove the Eject Arms (both right and left) and Mouse Button Latch and Spring (see below illustration). Note, the Mouse Latch Spring is very small and can be misplaced easily. Screw M2x4.
3. The Eject Buttons and Springs do not need to be removed to gain access to the Logic Board. However, because they can be dislodged easily, setting them aside is recommended. 4. Remove the Paw Carrier Flex Cable from the zero-force insertion slot. 5. Remove the five (5) screws from the Logic Board (see previous illustration). 6. The Logic Board can now be lifted from the Bottom Case. Replacement Procedure 1. To replace the Logic Board, reverse the steps in the Removal Procedure.
Paw Carrier (Paw Active) (HP Authorized Service Providers Only) Required Equipment • Appropriate ESD station • Torx #6 screwdriver • Two small flat tip screwdrivers (or similar prying devices) • Probe Removal Procedure 1. Follow the Logic Board PCA Removal Procedure. 2. Remove the Mylar Mouse Shield. Refer to the below illustration for location of components. 3. The Mouse Eject Arm and Eject Arm Spring may be removed at this point for convenience. 4. Gently bend the Pivot Bracket Tabs upward.
Other Components (HP Authorized Service Providers Only) The below table list additional replaceable components and the disassembly procedure(s) necessary to gain access to each.
Appendix A - Technical and Resource Specifications Mass Storage Specifications Average seek Track to Track seek Average Latency Rotational speed Data transfer rate Buffer to disc Buffer to host Buffer size Spindle start time 40MB 105MB 131MB < 19 ms 5 ms 19 ms 6 ms 19ms 6 ms Flash Disk Cards (Typical) 2-3 ms NA 6.67 ms 4503 rev/m 6.72 ms 4464 rev/m 6.72 ms 4464 rev/m NA NA 13-21 Mbits /sec 4.5 Mbytes /sec 11.4 - 19.2 Mbits/sec 4 Mbytes /sec 11.4 - 19.2 Mbits/sec 4 Mbytes/sec 2.
Memory Map 300/425 430 SYSTEM BIOS F VGA BIOS E D C B A ROM DOS 430 SYSTEM BIOS VGA BIOS UMB SPACE PCMCIA PCMCIA UMB SPACE VGA RAM UMB SPACE VGA RAM Upper Memory Block Space UMB Space Available OB300/425 64k OB430 64k + 32k OB530 112k contiguous DOS Conventional Memory Windows DOS Box (with LapLink Remote) Exit Windows (with out LapLink Remote) 68 OB300 315 KB OB425 315 OB430 505 OB530 404 435 KB 435 533 437
Appendix B - Power On Self Test Codes Beep Codes Beep Codes are used to identify a Power On Self Test (POST) error that occurs when the screen is not available. Once the screen is operational, diagnostic messages are reported to the screen. There are beep codes for both fatal and nonfatal system board errors. The codes are shown as x-y-z where 2-2-1 represents 2 beeps - pause - 2 beeps - pause - 1 beep.
Display Codes There are a number of Power On Self Test (POST) tests that are performed after the Beep Code tests. Failure of one or more of these tests will result in a displayed failure code (such as 0240). It is extremely important not to interpret a failure code immediately as a hardware failure. The failure should be confirmed with a clean boot.
0352h 0353h 0354h kbd not connected no response from kbd test kbd test failed error codes 0304, 0313-0314, 0321-0323, 0331-033C were previously used AUX Self Test Errors 03E0h 03E1h 03E2h 03E3h 03E4h 03E5h 03E6h 03E7h 03E8h 03E9h 03EAh 03EBh 03ECh Protected-Mode Switch Error 0401h send enable-aux cmd to 8042 cmd byte failed 8042 failed to accept write-auxdevice cmd write-aux-device cmd not sent by 8042 reset-aux cmd not accepted by 8042 8042 failed to send aux-interface-test no reply for aux-interfac
1300h 1301h 1302h 1303h 1304h 1305h Memory Configuration (POST) Errors 2000h bad port or wrong memory board 2001h 2002h 2003h bad port or wrong board type port reports null or no SIMMs can't mix single and double density SIMM parts physical SIMM config.
6300h BIOS and Memory Shadow-RAM Errors 8259 Interrupt Functionality Errors test (low 640k). x = 64k bank no. with problem (i.e.
Weitek Numerical CoProcessor Errors Video Errors 0a004h 0a005h 0a006h 0a007h 0a008h 0a009h 0a00ah 0a00bh 0a00ch 0a00dh 0a00eh FXCH or FCOMP didn't work FADD didn't work FMUL didn't work FDIV didn't work FSQRT didn't work FPATAN didn't work invalid operation exception err denormal operand exception error zero divide exception error overflow exception error underflow error 0af00h failed to enter protected mode 0af01h 0af02h 0af05h 0af06h 0af0Ch there is no Weitek in the system error in Weitek data regi
Appendix C - Password Policy If the user forgets the system password, there is a master password that will unlock the OmniBook. The user calls Technical Support to determine this master password as follows: 1. Support will tell the user the keys to type at the password entry screen: [alt][shft][f10] 2. The OmniBook generates and displays an encoded master password. This is displayed under the normal password entry area.
Further, you must log the name, serial number and date of the running of the descramble program, and file the written backup with the log. The log and backup are subject to standard record retention process and review. The final issue relating to descramble of passwords is that HP cannot provide information to users that would assist them in improperly descrambling a password and opening a unit.
Appendix D - Part Numbers Part Number 0380-4060 0515-2396 F1030-00016 F1030-00026 F1030-00029 F1030-00030 F1030-20001 F1030-40013 F1030-40014 F1030-40016 F1030-40017 F1030-40018 F1030-40019 F1030-40021 F1030-40025 F1030-40033 F1030-40044 F1030-40045 F1030-40046 F1030-40047 F1030-40050 F1030-60901 F1030-60904 F1030-60907 F1030-60908 F1030-60909 F1030-60910 F1030-60911 F1030-60912 F1030-60923 F1030-60924 F1030-60925 F1030-60926 F1030-80013 F1030-80015 F1030-80018 F1030-80019 F1030-80031 F1030-80032 F1030-8003
Part Number F1033-60912 F1037-60901 F1037-60902 F1037-60903 F1037-60904 F1037-60905 F1037-60906 F1037-60907 F1052-40007 F1052-40012 F1052-60005 F1052-60906 F1052-60907 F1052-60908 F1052-60914 F1052-60915 F1052-69008 F1065-60029 Description OB300 OB425 OB430 OB530 System ROM (ABE) Spanish SVC Icon Label 430 (10 pack) Custom Icon Kit (10 pack) Sys ROM (ABA) US English Sys ROM (ABB) Int.
HP Part Number 5965-0244
