User's Manual
Table Of Contents
- HP 3PAR Storage Replication Adapter 5.5.2 for VMware® vCenter Site Recovery Manager™ User Guide
- Contents
- 1 Introduction
- 2 VMware vCenter Site Recovery Manager overview
- 3 Supported configurations
- 4 HP 3PAR SRA installation and configuration prerequisites
- 5 Installing HP 3PAR SRA
- 6 HP 3PAR storage system setup
- 7 Configuring VMware vCenter Site Recovery Manager and HP 3PAR SRA
- 8 Recovery and failback
- 9 HP 3PAR SRA for the VMware SRM 5.5 utility
- 10 Partial licensing
- 11 HP 3PAR SRA 5.5.2 SRM vs HP 3PAR Remote Copy state diagram
- 12 Special notes
- 13 Support and other resources
- 14 Documentation feedback
Support for SLD
• HP 3PAR SRA supports synchronous long distance remote copy groups on HP 3PAR OS 3.1.2
MU3 P16 or later MUs, and HP 3PAR OS 3.1.3 or later.
• HP 3PAR SRA can coexist with a synchronous long distance remote copy group on HP 3PAR
OS version 3.1.1 to HP 3PAR OS 3.1.2 MU2.
Workarounds for SLD error codes
This section describes workaround for the following SLD error codes:
• Error code 1110: One of the failure reasons might be remote copy replication role of the RC
Group <RC group name> in target storeserv system <target name> is not secondary.
Please manually issue the HP 3PAR remote copy setrcopygroup CLI command with reverse
option to change the role.
To resolve this, do the following:
1. Run the showrcopy groups <RC group name> command on the original protected
storage system.
2. If the group role is Primary-Rev, run the setrcopygroup reverse –local
–current <RC group name> command to change remote copy role.
• Error code 1112: HP 3PAR SRA is not able to connect to target storeserv system <target
name> to execute the failover operation with restore option. HP 3PAR SRA fails to connect to
target HP 3PAR storeserv system with the available credentials. Please try the following options
1. Try accepting target HP 3PAR SSL certificate again 2. Verify the connectivity to target HP
3PAR array from SRM host and retry the operation. If above options do not resolve the issue,
please manually issue the HP 3PAR remote copy setrcopygroup CLI command with
restore option to change the replication roles.
To resolve this, do the following:
1. On the protected storage system, run the showrcopy groups <RC group name>
command.
2. On the recovery storage system, run the showrcopy groups <RC group name> the
command.
3. If the group role is Primary-ReV on the protected storage system, and Secondary-Rev
on the recovery storage system, run the setrcopygroup restore -t <targetname>
<RC group name> command on the protected storage system to change the remote
copy roles.
Limitations of SLD configuration
In an SLD remote copy environment with three HP 3PAR StoreServ Storage systems (A, B, and C),
where A—B is configured in synchronous mode, A—C in asynchronous periodic mode, and B—C
is the standby link in asynchronous periodic mode. SRM/SRA is configured between HP 3PAR
StoreServ Storage systems A and C.
• Restore replication after failover:
Data can be restored at the original protected site (A) by discarding all changes made at site
(C) after failover. You cannot perform this from the SRM GUI. However, you can run the
commands prepareRestoreReplication and restoreReplication in sequence.
You can run these commands from the command prompt using the XML input files.
NOTE: If the commands are executed from the command prompt, the SRM GUI might not
reflect the latest status.
For SLD Remote Copy groups, after restore replication , only the remote copy group between
A—C will be started automatically by SRA. Once Restore Replication is complete, you must
38 Special notes