HP 37717C communications performance analyzer Configuration guide New dual SONET/SDH and DS1/DS3 capability Effective from February 1998 ear 3-y nty as d rra wa tandar s New capability ä Dual standard SONET/SDH ä DS1, DS3 interfaces ä STS-1, STS-3 electrical ä OC-1, OC-3, OC-12 optical ä OC-12c and STM-4c ä STM-0, STM-1, STM-4 optical ä Protection switch times
Contents Small Siemens cross-reference Introduction ....................................................................................... 2 All options listed in the following pages are BNC. If you need small Siemens connectors, use the table below to select equivalent Siemens option. BNC UKK UKJ 110 UKN UKZ ➝ ➝ ➝ Module interworking ......................................................................... 6 USB USA not applicable USE not applicable Other options and accessories ...................
Introduction Your choice of test capability The HP 37717C communications performance analyzer supports comprehensive functional test and jitter capability to help you test your PDH/DSn, SONET/SDH and ATM networks or network equipment. The analyzer comprises a mainframe with large color display and integral floppy disk drive, optional 80-column graphics printer, and includes power cord and operating manuals. You add the test capability you require by selecting from the optional test modules.
Example configurations Option code Slots used 1. PDH/DSn and ATM test and interfaces option UKJ 2 2. SONET/SDH test and interfaces option A3R 2 1. STM-4o/STM-1o plus jitter Example user requirements ● PDH (2, 8, 34, 140 Mb/s) – mux/demux capability 3. Wander and jitter generation option A3K 1 ● STM-1e (155 Mb/s) electrical interfaces 4. Wander and jitter measurement option A3N 2 ● STM-4o/STM-1o (1310 nm) optical interfaces 5.
Configuring the HP 37717C communications performance analyzer 1 2 3 4 5 6 7 8 Remote Optical There are reserved slots for optical interfacing and remote-control modules. In addition, you have a maximum of eight userconfigurable slots to add PDH/DSn, SONET/SDH, ATM and jitter capability. Ensure that the number of slots used does not exceed eight. Step 1 Review sections 1 to 12 in the following pages to determine the capability you require.
Module interworking section The following three tables indicate which modules are capable of networking with each other. Choose one from each category (if required)† PDH/SDH and ATM cell layer supported configurations PDH/ATM cell test and PDH interfaces Option UKK Page 8 Unstructured PDH: 0.7, 2, 8, 34 and 140 Mb/s. Option UKJ Page 8 Structured PDH: 2, 8, 34 and 140 Mb/s. Option UKN Page 8 ATM cell: 2, 34 and 140 Mb/s (includes all capability of option UKJ).
Broadband ATM services supported configurations ATM cell test interfaces Option UKN 1 Page 8 ATM cell generation and analysis: 2, 34 and 140 Mb/s (includes all capability of option UKJ structured PDH). Option UKZ 2 Page 8 Generation and measurement of ATM payloads: 1.544 (DS1), 44.736 (DS3), 2.048 (E1) and 34.368 (E3) Mb/s. 1 ITU-T 2 ANSI/ITU-T STM-1e test and interfaces Option A1T Page 8 STM-1e (155 Mb/s) electrical interface. Overhead access, thru mode and pointer sequences.
Option code 1. No of slots Tick one PDH/DSn and ATM test and interfaces options Choose one option (if required). All options provide PDH interfaces and PDH test capability. ● Unstructured PDH testing: 0.7, 2, 8, 34 and 140 Mb/s interfaces plus an error output. ................. UKK ● Structured PDH testing: 2, 8, 34 and 140 Mb/s interfaces (64 kb/s and n × 64 kb/s testing). ......... UKJ 2 2 ● ATM cell generation and analysis: 2, 34 and 140 Mb/s interfaces† .......................................
Option code 4. No of slots Tick one Wander and jitter measurement options Choose one option (if required). If you need PDH jitter measurement then also order PDH/DSn interface option (section 1). ● PDH (tributary) jitter and wander measurement: 2, 8, 34, 140 Mb/s, with HP1, HP2 and ............... UHN LP filters to ITU-T O.171 plus 2 Mb/s wander and estimated frame slip measurement. 1 ● STM-1e line jitter and PDH (tributary) jitter; rms, peak-to-peak, auto jitter transfer ......................
Option code 7. Tick one Optical interfaces options Choose one option (if required). All optical interfaces receive at 1310 and 1550 nm. Provides optical interfaces. Must also order STM-0e/STM-1e option A3R (section 2), and appropriate optical adaptor options (section 12). STM-1 optical interfaces only (for testing STM-1 only)* ● 155 Mb/s optical interface: 1310 nm, −9 dBm output. ..............................................................................
Option code 9. No of slots Tick if required Multiple PDH interfaces option Choose if required. Must also order a PDH and ATM test and interface option UKK, UKJ or UKN (section 1). ● Three additional 2, 8, 34 and 140 Mb/s outputs. ......................................................................................... UHC 1 Option code 10. Tick one Remote-control/external-printer interfaces options Choose one option (if required). ● RS-232-C and HP-IB remote-control/external-printer interfaces.
Other options and accessories Optical coupler Graphics printer paper HP15744A: Optical coupler.* Printer paper: Part number 9270-1360. *Order the appropriate option. For full details of the HP 15744A optical coupler, please ask your local HP representative for a brochure. The optical coupler and graphics printer (option UKX) cannot both be fitted at the same time. HP 15722A: Telephone handset for options UKJ or UKN. Fiber optic cable HP E4545A: 3 m fiber optic cable (FC/PC connectors).
