Installation manual

ManualsBrandsHP ManualsComputer equipment300-1020

Table Of Contents

lios.apana.org.au

Sun Internal ONLY
!!
The Sun-4 Handbook describes and illustrates the Sun-4 and
Sun-4e products for service providers who service these products after the End
of Support Life in April 1997.
End of Support Life is the end of Sun's commitment to support the product. Sun may help customers
locate alternative sources for support on a case-by-case basis if ongoing support is needed beyond 5
years. Spares availability after End of Support Life may be limited and repair service will be at Sun's
discretion.
Sun-4 Handbook - Home Page
http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00000/wcd00036.htm (1 von 2) [25.04.2002 15:56:23]

Summary of content (566 pages)

PAGE 1
Sun-4 Handbook - Home Page Sun Internal ONLY !! The Sun-4 Handbook describes and illustrates the Sun-4 and Sun-4e products for service providers who service these products after the End of Support Life in April 1997. End of Support Life is the end of Sun's commitment to support the product. Sun may help customers locate alternative sources for support on a case-by-case basis if ongoing support is needed beyond 5 years.
PAGE 2
Sun-4 Handbook - Home Page [ Configurations ] [ CPU ] [ Memory ] [ Graphics ] [ IPI ] [ SCSI ] [ SCSI Disk ] [ Removable Media ] [ Communication ] [ Miscellaneous ] [ Backplane ] [ Slot Assignment ] [ Parts Introduction ] [ System ] [ Disk Options ] [ Removable Media Options ] [ Miscellaneous Options ] [ Board ] [ Input Device ] [ Monitor ] [ Printer ] [ CPU Trouble ] [ Disk Trouble ] [ Diagnostics ] [ Power Introduction ] [ AC Power ] [ DC Power ] The original hardcopy publication of the Sun-4 Handbook is
PAGE 3
Sun4/II: DC Power - Contents DC Power Power Supplies 300-1020 -- Brown -- 575 Watts 300-1020 -- Fuji -- 575 Watts 300-1022 -- Summit -- 325 Watts 300-1022 -- Brown -- 325 Watts 300-1024 -- Fuji -- 850 Watts 300-1031 -- Delta -- 120 Watts 300-1034 -- Boschert -- 520 Watts 300-1041 -- Seagate -- 205 Watts 300-1043 -- Fuji -- 925 Watts 300-1045 -- Boschert -- 130 Watts 300-1047 -- Zytec -- 925 Watts 300-1052 -- Fuji -- 820 Watts 300-1056 -- Fuji -- 410 Watts 300-1065 -- Zytec -- 1200 Watts 300-1072 -- Boscher
PAGE 4
Sun4/II: Power - Brown 300-1020 Brown 300-1020 575 Watt Power Supply Sun-4/150/350 300-1020 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006b9.htm (1 von 2) [25.04.
PAGE 5
Sun4/II: Power - Brown 300-1020 Fuse 10 Amps @ 250 Volts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006b9.htm (2 von 2) [25.04.
PAGE 6
Sun4/II: Power - Fuji PEX445-30 575 Watt Power Supply Fuji PEX445-30 575 Watt Power Supply Sun-4/150/350 300-1020 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ba.htm (1 von 2) [25.04.
PAGE 7
Sun4/II: Power - Fuji PEX445-30 575 Watt Power Supply Fuse 15 Amps @ 250 Volts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ba.htm (2 von 2) [25.04.
PAGE 8
Sun4/II: Power - Summit CS0325-9001 325 Watt Power Supply Summit CS0325-9001 325 Watt Power Supply Sun-4/110/310 300-1022 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bb.htm (1 von 2) [25.04.
PAGE 9
Sun4/II: Power - Summit CS0325-9001 325 Watt Power Supply Fuse 7 Amps @ 250 Volts Note Wait at least two minutes after power down or power outage before turning power ON to allow the unit to reset. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bb.htm (2 von 2) [25.04.
PAGE 10
Sun4/II: Power - Brown PS41 325 Watt Power Supply Brown PS41 325 Watt Power Supply Sun-4/110/310 300-1022 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bc.htm (1 von 2) [25.04.
PAGE 11
Sun4/II: Power - Brown PS41 325 Watt Power Supply Fuse: 7 Amps @ 250 Volts Note Wait at least two minutes after power down or power outage before turning power ON to allow the unit to reset. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bc.htm (2 von 2) [25.04.
PAGE 12
Sun4/II: Power - Fuji PEX391 850 Watt Power Supply Fuji PEX391 850 Watt Power Supply Sun-4/260/280/360/380 300-1024 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bd.htm (1 von 2) [25.04.
PAGE 13
Sun4/II: Power - Fuji PEX391 850 Watt Power Supply Fuse 30 Amps @ 250 Volts Note The Fuji 300-1024 is the same as the Fuji 300-1016. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bd.htm (2 von 2) [25.04.
PAGE 14
Sun4/II: Power - Delta DPS-118AB 120 Watt Power Supply Delta DPS-118AB 120 Watt Power Supply Options 526 / 527 / 530 / 539 / 561 / 563 / 565 Options 566 / RR126 / RR128 / RR129 / RREXP 300-1031 Fuses 4 Amps @ 250 Volts 3 Amps @ 250 Volts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006be.htm (1 von 2) [25.04.
PAGE 15
Sun4/II: Power - Delta DPS-118AB 120 Watt Power Supply Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006be.htm (2 von 2) [25.04.
PAGE 16
Sun4/II: Power - Boschert XL520-3625 520 Watt Power Supply Boschert XL520-3625 520 Watt Power Supply Sun-4/330 300-1034 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bf.htm (1 von 2) [25.04.
PAGE 17
Sun4/II: Power - Boschert XL520-3625 520 Watt Power Supply Fuses F1 = 20 Amps @ 250 volts F2 = 10 Amps @ 250 volts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bf.htm (2 von 2) [25.04.
PAGE 18
Sun4/II: Power - Seagate 45070622 205 Watt Power Supply Seagate 45070622 205 Watt Power Supply Seagate 97209-12G Disk Drive Options 706 / 707 / 709 / 710 300-1041 Fuse Soldered at F 100, 8 Amps @ 250 Volts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c0.htm (1 von 2) [25.04.
PAGE 19
Sun4/II: Power - Seagate 45070622 205 Watt Power Supply Notes 205 Watt Power Supply 300-1041 Supports one Seagate 97209-12G 3MB/Sec IPI Disk Drive. Does NOT Support the Seagate 97229-11G 6MB/Sec IPI Disk Drive. 215 Watt Power Supply 300-1074 Supports one Seagate 97209-12G 3MB/Sec IPI Disk Drives. Supports one Seagate 97229-11G 6MB/Sec IPI Disk Drives. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c0.htm (2 von 2) [25.04.
PAGE 20
Sun4/II: Power - Fuji PEX479-30 925 Watt Power Supply Fuji PEX479-30 925 Watt Power Supply Sun-4/260/280/360/380 300-1043 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c1.htm (1 von 2) [25.04.
PAGE 21
Sun4/II: Power - Fuji PEX479-30 925 Watt Power Supply Fuse Littelfuse 30A 250V BLN 30 Note Use wire harnesses 530-1578 and 530-1580 for the 80/280/380/480 chassis. Use wire harnesses 530-1578 and 530-1581 for the 160/260/360/460 chassis. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c1.htm (2 von 2) [25.04.
PAGE 22
Sun4/II: Power - Boschert XL121-3630 130 Watt Power Supply Boschert XL121-3630 130 Watt Power Supply Options 501 / 503 / 504 / 505 / 506 / 507 Options 509 / 510 / 511 / 514 / 516 300-1045 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c2.htm (1 von 2) [25.04.
PAGE 23
Sun4/II: Power - Boschert XL121-3630 130 Watt Power Supply Fuse 5 Amps @ 250 Volts Note Use Power Harness, 530-1432-01, for this power supply. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c2.htm (2 von 2) [25.04.
PAGE 24
Sun4/II: Power - Zytec 22903110 925 Watt Power Supply Zytec 22903110 925 Watt Power Supply Sun-4/370/470 Options 509 / 510 / 511 / 514 / 516 300-1047 DC OUTPUT REGULATION FULL LOAD +5 150 Amps 145.0 Amps -5.2 15 Amps 10.0 Amps +12 analog 15 Amps 2.0 Amps http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c3.htm (1 von 2) [25.04.
PAGE 25
Sun4/II: Power - Zytec 22903110 925 Watt Power Supply +12 motor -12 15 Amps 10 Amps 6.3 Amps 4.0 Amps Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c3.htm (2 von 2) [25.04.
PAGE 26
Sun4/II: Power - Fuji PEX527-30 820 Watt Power Supply Fuji PEX527-30 820 Watt Power Supply Options 733 / 734 300-1052 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c4.htm (1 von 2) [25.04.
PAGE 27
Sun4/II: Power - Fuji PEX527-30 820 Watt Power Supply Fuse 20 Amps @ 250 Volts Notes 820 Watt Power Supply 300-1052-02 Supports four CDC 9720-688 Disk Drives. Supports four Fujitsu M2372K Disk Drives. 820 Watt Power Supply 300-1052-03 Supports four CDC 9720-688 Disk Drives. Does not support the Fujitsu M2372K Disk Drive. Supports two Seagate 97209-12G 3MB/Sec IPI Disk Drives. Does not Support Seagate 97229-11G 6MB/Sec IPI Disk Drives.
PAGE 28
Sun4/II: Power - Fuji PEX527-40 410 Watt Power Supply Fuji PEX527-40 410 Watt Power Supply Options 731 / 732 300-1056 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c5.htm (1 von 2) [25.04.
PAGE 29
Sun4/II: Power - Fuji PEX527-40 410 Watt Power Supply Fuse 20 Amps @ 250 Volts Notes 410 Watt Power Supply 300-1056-02 Supports two CDC 9720-688 Disk Drives. Supports two Fujitsu M2372K Disk Drives. 410 Watt Power Supply 300-1056-03 Supports two CDC 9720-688 Disk Drives. Does not support the Fujitsu M2372K Disk Drive. 410 Watt Power Supply 300-1056-04 Supports two CDC 9720-688 Disk Drives. Does not support the Fujitsu M2372K Disk Drive.
PAGE 30
Sun4/II: Power - Zytec 22907400 1200 Watt Power Supply Zytec 22907400 1200 Watt Power Supply Sun-4/390/490 SS690 300-1065 DC OUTPUT REGULATION FULL LOAD +5 10-200 Amps 200.0 Amps -5.2 0.4-15 Amps 10.0 Amps +12 analog 0-10 Amps 2.0 Amps http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c6.htm (1 von 2) [25.04.
PAGE 31
Sun4/II: Power - Zytec 22907400 1200 Watt Power Supply +12 motor -12 4-15 Amps 0-5 Amps 6.3 Amps 4.0 Amps Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c6.htm (2 von 2) [25.04.
PAGE 32
Sun4/II: Power - Boschert XL520-3625 520 Watt Power Supply Boschert XL520-3625 520 Watt Power Supply Sun-4/330 / SS630 300-1072 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c7.htm (1 von 2) [25.04.
PAGE 33
Sun4/II: Power - Boschert XL520-3625 520 Watt Power Supply Fuses F1 = 20 Amps @ 250 Volts F2 = 10 Amps @ 250 Volts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c7.htm (2 von 2) [25.04.
PAGE 34
Sun4/II: Power - Seagate 45070625 215 Watt Power Supply Seagate 45070625 215 Watt Power Supply Seagate 97209-12G / Seagate 97229-11G Options 706 / 707 / 709 / 710 / 716 / 717 / 719 / 720 300-1074 Fuse At F 100, 8 Amps, 250 Volts, LittleFuse, 312-008 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c8.htm (1 von 2) [25.04.
PAGE 35
Sun4/II: Power - Seagate 45070625 215 Watt Power Supply Notes 205 Watt Power Supply 300-1041 Supports one Seagate 97209-12G 3MB/Sec IPI Disk Drive. Does NOT Support the Seagate 97229-11G 6MB/Sec IPI Disk Drive. 215 Watt Power Supply 300-1074 Supports one Seagate 97209-12G 3MB/Sec IPI Disk Drives. Supports one Seagate 97229-11G 6MB/Sec IPI Disk Drives. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c8.htm (2 von 2) [25.04.
PAGE 36
Sun4/II: Power - Fuji PEX527-31 840 Watt Power Supply Fuji PEX527-31 840 Watt Power Supply Options 741 / 742 / 743 / 744 300-1075 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c9.htm (1 von 2) [25.04.
PAGE 37
Sun4/II: Power - Fuji PEX527-31 840 Watt Power Supply Fuse 20 Amps @ 250 Volts Notes 840 Watt Power Supply 300-1075 Supports four Seagate 97209-12G 3MB/Sec IPI Disk Drives. Supports four Seagate 97229-11G 6MB/Sec IPI Disk Drives. Does not support Fujitsu M2372K Disk Drives. Does not support CDC 9720-688 Disk Drives. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c9.htm (2 von 2) [25.04.
PAGE 38
Sun4/II: Power - Zytec 22914300 268 Watt Power Supply Zytec 22914300 268 Watt Power Supply Options 726 / 727 300-1085 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ca.htm (1 von 2) [25.04.
PAGE 39
Sun4/II: Power - Zytec 22914300 268 Watt Power Supply Fuse 10 Amps @ 250 Volts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ca.htm (2 von 2) [25.04.
PAGE 40
Sun4/II: Power - Fuji PEX526-30 925 Watt Power Supply Fuji PEX526-30 925 Watt Power Supply Sun-4/370/470 300-1089 DC OUTPUT REGULATION FULL LOAD +5 150 Amps 145.0 Amps -5.2 15 Amps 10.0 Amps +12 analog 15 Amps 2.0 Amps +12 motor 15 Amps 6.3 Amps -12 10 Amps 4.0 Amps http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cb.htm (1 von 2) [25.04.
PAGE 41
Sun4/II: Power - Fuji PEX526-30 925 Watt Power Supply Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cb.htm (2 von 2) [25.04.
PAGE 42
Sun4/II: Power - Fuji PEX614-30 820 Watt Power Supply Fuji PEX614-30 820 Watt Power Supply Options 750 / 754 / 756 300-1091 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cc.htm (1 von 2) [25.04.
PAGE 43
Sun4/II: Power - Fuji PEX614-30 820 Watt Power Supply Fuse Littelfuse BLN 20 Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cc.htm (2 von 2) [25.04.
PAGE 44
Sun4/II: Power - Fuji PEX614-31 800 Watt Power Supply Fuji PEX614-31 800 Watt Power Supply Options 750 / 754 / 756 / 762 / 763 / 764 300-1106 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cd.htm (1 von 2) [25.04.
PAGE 45
Sun4/II: Power - Fuji PEX614-31 800 Watt Power Supply Fuse Littelfuse BLN 20 Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cd.htm (2 von 2) [25.04.
PAGE 46
Sun4/II: Power - Fujitsu M2444AC Power Supply Fujitsu M2444AC Power Supply A-1 Options 78 / 675 811-1027 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ce.htm (1 von 3) [25.04.
PAGE 47
Sun4/II: Power - Fujitsu M2444AC Power Supply Fujitsu M2444AC Power Supply A-2 Options 78 / 675 811-1027 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ce.htm (2 von 3) [25.04.
PAGE 48
Sun4/II: Power - Fujitsu M2444AC Power Supply Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ce.htm (3 von 3) [25.04.
PAGE 49
Sun4/II: Power - HP 88780 Power/Motor Drive Power Supply HP 88780 Power/Motor Drive Power Supply Options 680 / 682 / 683 / 684 811-1242 Note Use 6 Amp fuse 140-1021-01. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cf.htm [25.04.
PAGE 50
Sun4/II: AC Power - Contents AC Power AC Power Sequencer Remote and Local Bus Connectors Power Requirements 300-1011 -- Pulizzi Engineering -- 115V 370-1027 -- Pulizzi Engineering -- 230V 370-1155 -- Pulizzi Engineering -- 230V 370-1126 -- Pulizzi Engineering -- 240V 370-1156 -- Pulizzi Engineering -- 240V 370-1155-02 -- Sherwood Enterprises -- 230V 300-1263 -- Sherwood Enterprises -- 230V 370-1156-03 -- Sherwood Enterprises -- 240V 300-1264 -- Sherwood Enterprises -- 240V Last updated: February 6, 1997 Co
PAGE 51
Sun4/II: Power - AC Power Sequencer AC Power Sequencer Remote and Local Bus Connectors 300-1011 / 300-1263 / 300-1264 370-1126 / 370-1127 / 370-1155 / 370-1156 Remote I/O Connectors J6, J7, J8, and J9 A parallel circuit connects J6, J7, J8, and J9. Inputs to the Remote I/O Connectors are activated by mechanical toggle, key switch, transistor, integrated circuit, or thermoswitch with a normal open configuration.
PAGE 52
Sun4/II: Power - AC Power Sequencer LOCAL The AC output of the Switched 1 and Switched 2 outlets is enabled when the Circuit Breaker is ON. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0069d.htm (2 von 2) [25.04.
PAGE 53
Sun4/II: Power - AC Sequencer Power Requirements AC Sequencer Power Requirements 300-1011 / 300-1027 / 300-1263 300-1264 / 370-1126 / 370-1155 / 370-1156 Operating Range Nominal Voltage: 208, 220, 230, or 240 Volts AC Operating Voltage: Single Phase 180-264 Volts AC Frequency: 48-63 Hz Current: 24 A maximum AC Power Plug The 230VAC power plug is a NEMA L6-30P. The 240VAC power plug is a Blue, 32A, IEC 309, with Ground at the 6-hour position.
PAGE 54
Sun4/II: Power - AC Sequencer Power Requirements IEC 309 240 Volt Power Receptacle Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0069e.htm (2 von 2) [25.04.
PAGE 55
Sun4/II: Power - Pulizzi Engineering PC874C and PC874D 115 Volt AC Power Sequencer 300-1011 Pulizzi Engineering PC874 Outlet Side Control Side Notes 1. Requires AC outlet NEMA L5-30R, 30A, 125V. 2. Any conversion to the Data Center Cabinet, including replacement of the AC Power Plug or AC Power Sequencer, voids all safety agency approvals. 3. The Switched 2 output comes on after a 5 second delay. http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0069f.htm (1 von 2) [25.04.
PAGE 56
Sun4/II: Power - Pulizzi Engineering PC874C and PC874D References 1. 2. 3. 4. 5. Installation Manual for the Sun Full-height Rack System, 800-1555. Installation Manual for Sun Rackmountable Fileservers, 800-1556. Sun Full-Height Rack System Installation Manual, 800-1677. Sun Rackmountable Fileservers Installation Manual, 800-1676. Sun 900 Mbyte Disk Drive Installation Manual, 800-1036. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.
PAGE 57
Sun4/II: Power - Pulizzi Engineering PC874C and PC874D 230 Volt AC Power Sequencer 230 Volt AC Power Sequencer 370-1027 370-1155 Pulizzi Engineering Pulizzi Engineering PC874 PC874 Outlet Side Control Side Notes 1. Requires AC outlet NEMA L6-30R, 30A, 250V. 2. Any conversion to the Data Center Cabinet, including replacement of the AC Power Plug or AC Power Sequencer, voids all safety agency approvals. 3. The Switched 2 output of 370-1127 comes on after a 5-second delay. 4.
PAGE 58
Sun4/II: Power - Pulizzi Engineering PC874C and PC874D 230 Volt AC Power Sequencer References 1. 2. 3. 4. Sun Full-Height Rack System Installation Manual, 800-1677. Sun Rackmountable Fileservers Installation Manual, 800-1676. Sun 900 Mbyte Disk Drive Installation Manual, 800-1036. Sun 56-inch Data Center Cabinet and Data Center Expansion Cabinet Installation Manual, 800-3242. 5. Sun 56-inch Expansion Cabinet Installation Manual, 800-5936-18. 6. Sun 56-inch Cabinet Service Manual, 800-6371-17.
PAGE 59
Sun4/II: Power - Pulizzi Engineering PC874C and PC874D 240 Volt AC Power Sequencer 240 Volt AC Power Sequencer 370-1126 370-1156 Pulizzi Engineering Pulizzi Engineering PC874 PC874 Outlet Side Control Side Notes 1. Requires a Blue, IEC 309, 2-Pole, 3-Wire, 32A, 250V AC receptacle. 2. Any conversion to the Data Center Cabinet, including replacement of the AC Power Plug or AC Power Sequencer, voids all safety agency approvals. 3. The AC Power Cord is internally wired to the AC Line Filter. 4.
PAGE 60
Sun4/II: Power - Pulizzi Engineering PC874C and PC874D 240 Volt AC Power Sequencer References 1. 2. 3. 4. Sun Full-Height Rack System Installation Manual, 800-1677. Sun Rackmountable Fileservers Installation Manual, 800-1676. Sun 900 Mbyte Disk Drive Installation Manual, 800-1036. Sun 56-inch Data Center Cabinet and Data Center Expansion Cabinet Installation Manual, 800-3242. 5. Sun 56-inch Expansion Cabinet Installation Manual, 800-5936-18. 6. Sun 56-inch Expansion Cabinet Service Manual, 800-6371-17.
PAGE 61
Sun4/II: Power - Sherwood Enterprises 230 Volt AC Power Sequencer 230 Volt AC Power Sequencer 370-1155-02 Sherwood Enterprises Outlet Side Control Side Notes 1. Requires AC outlet NEMA L6-30R, 30A, 250V. 2. Any conversion to the Data Center Cabinet, including replacement of the AC Power Plug or AC Power Sequencer, voids all safety agency approvals. 3. The Switched 2 output comes on after a 20-second delay. References 1. 2. 3. 4. Sun Full-Height Rack System Installation Manual, 800-1677.
PAGE 62
Sun4/II: Power - Sherwood Enterprises 230 Volt AC Power Sequencer 5. Sun 56-inch Expansion Cabinet Installation Manual, 800-5936-18. 6. Sun 56-inch Expansion Cabinet Service Manual, 800-6371-17. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006a2.htm (2 von 2) [25.04.
PAGE 63
Sun4/II: Power - Sherwood Enterprises 230 Volt AC Power Sqncr 1263 230 Volt AC Power Sequencer 300-1263 Sherwood Enterprises Outlet Side Control Side Notes 1. Requires AC outlet NEMA L6-30R, 30A, 250V. 2. Any conversion to the Data Center Cabinet, including replacement of the AC Power Plug or AC Power Sequencer, voids all safety agency approvals. 3. The Switched 2 output comes on after a 20 second delay. 4. The 300-1263 replaced 370-1155-02 in February 1996. References 1.
PAGE 64
Sun4/II: Power - Sherwood Enterprises 240 Volt AC Power Sequencer 240 Volt AC Power Sequencer 370-1156-03 Sherwood Enterprises Outlet Side Control Side Notes 1. Requires a Blue, IEC 309, 2-Pole, 3-Wire, 32A, 250V AC receptacle. 2. Any conversion to the Data Center Cabinet, including replacement of the AC Power Plug or AC Power Sequencer, voids all safety agency approvals. 3. The AC Power Cord is internally wired to the AC Line Filter. 4. The Switched 2 output comes on after a 20 second delay.
PAGE 65
Sun4/II: Power - Sherwood Enterprises 240 Volt AC Power Sequencer References 1. 2. 3. 4. Sun Full-Height Rack System Installation Manual, 800-1677. Sun Rackmountable Fileservers Installation Manual, 800-1676. Sun 900 Mbyte Disk Drive Installation Manual, 800-1036. Sun 56-inch Data Center Cabinet and Data Center Expansion Cabinet Installation Manual, 800-3242. 5. Sun 56-inch Expansion Cabinet Installation Manual, 800-5936-18. 6. Sun 56-inch Expansion Cabinet Service Manual, 800-6371-17.
PAGE 66
Sun4/II: Power - Sherwood Enterprises 240 Volt AC Power Sqncr 1264 240 Volt AC Power Sequencer 300-1264 Sherwood Enterprises Outlet Side Control Side Notes 1. Requires a Blue, IEC 309, 2-Pole, 3-Wire, 32A, 250V AC receptacle. 2. Any conversion to the Data Center Cabinet, including replacement of the AC Power Plug or AC Power Sequencer, voids all safety agency approvals. 3. The Switched 2 output comes on after a 20 second delay. 4. The 300-1264 replaced 370-1156-03 in February 1996. References 1.
PAGE 67
II: Power - Introduction - Contents Power - Introduction AC Power Cords Fuses Wire Harnesses Sun 5-Slot Office Pedestal Wiring Diagram Sun 12-Slot Office Pedestal Wiring Diagram Sun 16-Slot Logic Enclosure Wiring Diagram Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004ea.htm [25.04.
PAGE 68
II: Power - AC Power Cords AC Power Cords PART # 180-1010 180-1117 180-1097 180-1125 180-1126 180-1142 180-1146 180-1176 180-1177 180-1177 180-1177 180-1178 180-1178 180-1178 180-1179 180-1179 180-1183 180-1184 180-1189 180-1190 180-1234 180-1235 180-1236 180-1683 180-1688 180-1732 530-1343 530-1351 530-1370 530-1371 530-1410 530-1411 530-1583 530-1584 530-1585 530-1586 530-1604 DESCRIPTION IEC 320 - Reverse IEC 320, Coiled (obs) IEC 320 - Reverse IEC 320 IEC 320 - NEMA 5-15, 15A/125V IEC 320 - pigtail, 6
PAGE 69
II: Power - AC Power Cords 530-1657 90° IEC 320 - NEMA 5-15, 10A/125V, Grey USA 530-1663 90° IEC 320 - CEE 7/7, 10A/250V, Grey France 530-1663 90° IEC 320 - CEE 7/7, 10A/250V, Grey Germany 530-1664 90° IEC 320 - SEV 1011, 10A/250V, Grey France 530-1664 90° IEC 320 - SEV 1011, 10A/250V, Grey Germany 530-1664 90° IEC 320 - SEV 1011, 10A/250V, Grey Switzerland 530-1665 90° IEC 320 - CEI 23-16/VII, 10A/250V, Grey Italy 530-1666 90° IEC 320 - 107/10-1973, 10A/250V, Grey Denmark 530-1667 90° IEC 320 - AS 3112, 1
PAGE 70
II: Power - AC Power Cords Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006e8.htm (3 von 3) [25.04.
PAGE 71
II: Power - Fuses Fuses FUSE 1/16A 1/16A 1/8A 1/8A 1/2A 3/4A 3/4A 3/4A 1A 1A 1A 1A 1A 1.5A 1.5A 1.5A 1.5A 1.6A 1.6A 1.6A 1.6A 1.6A 1.6A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2.5A 2.5A 2.5A 2.5A SIZE SUN PART # .25 x 1.25" 140-1004 .25 x 1.25" 140-1004 .25 x 1.25" 140-1003 .25 x 1.25" 140-1003 .25 x 1.25" 140-1012 PICO II 140-1024 .145 x .30" 140-1024 .25 x 1.25" 140-1044 .25 x 1.25" 140-1040 Microfuse 140-1027 .25 x 1.25" 140-1040 .25 x 1.25" 140-8500 .25 x 1.
PAGE 72
II: Power - Fuses 3A 3A 3A 3A 3A 3A 3A 3.15A 3.15A 4A 4A 4A 4A 4A 4A 4A 4A 4A 4A 4A 4A 5A 5A 5A 5A 5A 5A 5A 5A 6A 6A 6A 6A 6A 6A 6A 6A 6A 6A 6.3A 6.3A .25 x 1.25" PICO II .145 x .30" .25 x 1.25" .25 x 1.25" Microfuse Microfuse 5 x 20mm 5 x 20mm 5 x 20mm 5 x 20mm .25 x 1.25" .25 x 1.25" .25 x 1.25" .25 x 1.25" .25 x 1.25" .25 x 1.25" .25 x 1.25" .5 x 20mm .25 x 1.25" .25 x 1.25" .25 x 1.25" .25 x 1.25" 5 x 20mm 5 x 20mm 5 x 20mm 5 x 20mm 5 x 20mm .25 x 1.25" 5 x 20mm 5 x 20mm .25 x 1.25" .25 x 1.25" .
PAGE 73
II: Power - Fuses 7A 7A 8A 8A 8A 8A 10A 10A 10A 10A 10A 12A 12A 15A 15A 15A 15A 15A 15A 15A 15A 15A 30A .25 x 1.25" .25 x 1.25" .25 x 1.25" .25 x 1.25" 5 x 20mm 5 x 20mm .25 x 1.25" .25 x 1.25" .25 x 1.25" .25 x 1.25" 0.46 x 1.5" .25 x 1.25" .25 x 1.25" .25 x 1.25" .25 x 1.25" .25 x 1.25" .25 x 1.25" 0.46 x 1.5" 0.46 x 1.5" Nano2 PICO II 0.46 x 1.
PAGE 74
II: Power - Fuses Holder, In Line 22-14AWG Holder, In Line 22-14AWG Holder, UL/CSA/VDE Holder, R/A for PIG-TAIL Holder, R/A for PIG-TAIL Holder, 20A,250V,UL Microfuse Holder Microfuse Holder Holder Holder, Faston Type Holder, Faston Type Holder, Quick Connect Holder, Quick Connect Field Engineers Fuse Kit 140-1023 140-1023 150-1041 150-1163 150-1163 150-1177 150-1179 150-1179 150-1024 150-1026 150-1026 150-1029 150-1029 555-1126 AMP 552844-1 Littelfuse 155 020U Schurter FEU 031.
PAGE 75
II: Power - Fuses PTCs Positive Temperature Coefficient (PTC) thermistors are resistors with a high positive temperature coefficient of resistance. The PTC is used as a self-resetting fuse in overload applications. When an overload current flows through a PTC, there is a specific time period before the PTC heats up to its high-resistance state and starts limiting the current. PTCs are not field replaceable because they are soldered in place.
PAGE 76
II: Power - Wire Harnesses Wire Harnesses Wire Harness Color Codes The most common wire insulation colors used on Sun AC and DC wire harnesses are shown in the charts below. Not all products conform to these color codes. AC Wire Harnesses Color Abbreviation Description Green Grn AC Ground Black Blk AC Line (Hot) Green/Yellow Grn/Yel AC Ground Blue Blu AC Neutral Brown Brn AC Line (Hot) DC Wire Harnesses Color Abbreviation Description White Wht -5Vdc Yellow Yel -5.
PAGE 77
II: Power - Wire Harnesses A non-TUV female faston does not attach to a TUV male faston. Use adapter harness 811-9015-01. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ea.htm (2 von 2) [25.04.
PAGE 78
II: Power - Sun 5-Slot Office Pedestal Wiring Diagram Sun 5-Slot Office Pedestal Wiring Diagram Sun-4/330 and SPARCserver 630MP Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006eb.htm [25.04.
PAGE 79
II: Power - Sun 12-Slot Office Pedestal Wiring Diagram Sun 12-Slot Office Pedestal Wiring Diagram Sun-3/470, Sun-4/370, and Sun-4/470 shipped prior to August 1991 Sun-4/470 and SPARCserver 670MP shipped after August 1991 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ec.htm (1 von 2) [25.04.
PAGE 80
II: Power - Sun 12-Slot Office Pedestal Wiring Diagram Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ec.htm (2 von 2) [25.04.
PAGE 81
II: Power - Sun 16-Slot Logic Enclosure Wiring Diagram Sun 16-Slot Logic Enclosure Wiring Diagram Sun-4/390 shipped prior to April 1990 Sun-4/390, Sun-4/490, and SPARCserver 690MP shipped after April 1990 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ed.htm (1 von 2) [25.04.
PAGE 82
II: Power - Sun 16-Slot Logic Enclosure Wiring Diagram Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ed.htm (2 von 2) [25.04.
PAGE 83
Sun4/II: Trouble - Diagnostics - Contents Diagnostics Self-Test Diagnostic Diagnostic Executive 1.2 Diagnostic Executive (Sun-4) 1.2 Diagnostic Executive (Sun-4s) 1.6 Diagnostic Executive (Sun-4c) Sun Diagnostics 3.2 Loopback Connectors Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004e7.htm [25.04.
PAGE 84
Sun4/II: Trouble - Diagnostics - Self-Test Diagnostic Self-Test Diagnostic The CPU Self-Test runs in either the Normal or Diag mode. Set the CPU DIAG/NORM switch to DIAG or set the diag-switch? NVRAM parameter to true to enable the Diag mode. In the Normal mode, the CPU runs through a basic set of tests and reports errors on the diagnostic LEDs. Refer to the appropriate Field Service Manual and the Troubleshooting Section of this Handbook for self-test LED error code information.
PAGE 85
Sun4/II: Trouble - Diagnostics - Diagnostic Executive Diagnostic Executive The Diagnostic Executive (Exec) provides a single, unified diagnostic environment with one user interface. The diagnostic tests reside in individual programs that work through the Exec platform. The platform provides a consistent interface and multitasking capabilities. Some features are: Multiple Consoles The Exec can run from any control terminal. This may be a monitor, serial port, or a remote console.
PAGE 86
Sun4/II: Trouble - Diagnostics - 1.2 Diagnostic Executive 1.2 Diagnostic Executive Sun-4 Table of Contents NAME tpboot.sun4 Copyright toc extract_exec Copyright exec4 diags4 cg6.4exec cg8.4.exec cg9.4.exec color4.exec cpcache4.exec cpu4.exe eeptool4.exec ether4.exec ether2.4.exec exectest4.exec fddi4.exec fpu4.exec gp1.4.exec gp2.4.exec hsi4.exec ipi4.exec kb4.exec mcp4.exec mem4.exec mouse4.exec mti4.exec scsisub4.exec espscsi.exec smd4.exec taac4.
PAGE 87
Sun4/II: Trouble - Diagnostics - 1.2 Diagnostic Executive tape4.exec video4.exec vidmon4.exec vme4.exec netcon4 logfile eccmem4.diag cache4.
PAGE 88
Sun4/II: Trouble - Diagnostics - 1.2 Diagnostic Executive - Sun-4s 1.2 Diagnostic Executive - Sun-4s SPARCsystems 300/400 Table of Contents NAME FILE DESCRIPTION tpboot.sun4 0 Enables boot from tape Copyright 1 Textfile containing copyright notice toc 2 Contains list of contents of tape extract_exec 3 Script to copy diagnostics to disk Copyright 4 Textfile containing copyright notice exec4 5 Diag Exec for Sun-4s architecture diags4 6 Diagnostic Menu and File names cpu4.exe 7 CPU Board Diagnostic mem4.
PAGE 89
Sun4/II: Trouble - Diagnostics - 1.2 Diagnostic Executive - Sun-4s smd4.exec taac4.exec tape4.exec vme4.exec netcon4 logfile eccmem4.diag cache4.diag Copyright 33 34 35 36 37 38 39 40 41 Sun SMD Diagnostic TAAC Diagnostic Tape Diagnostic VME Diagnostic NETCON LOGFILE ECC Memory Diagnostic Cache Diagnostic Textfile containing copyright notice Reference SunDiagnostic Executive User's Guide Addenda, 800-3493-10. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.
PAGE 90
Sun4/II: Trouble - Diagnostics - 1.6 Diagnostic Executive 1.6 Diagnostic Executive Sun-4c Table of Contents NAME exec4c diags4c cache4c.exec cpu4c.exec bantam4c.exec codec4c.exec dbri4c.exec ether4c.exec fdc4c.exec fpu4c.exec kbm4c.exec mem4c.exec scsi4c.exec cg6.4c.exec video4c.exec spif4c.exec bipro4c.exec sunpc4c.exec vfc4c.exec hsis4c.exec token4c.exec cg12.4c.
PAGE 91
Sun4/II: Trouble - Diagnostics - Sun Diagnostics 3.2 Sun Diagnostics 3.2 Featuring: MPDiag and SunDiagnostic Executive 2.2 SS600MP / SS10 / SS1000 /SC2000 MPDiag tests the following components and functions: Audio Ethernet FPU Interrupts and Traps MBus Module Memory MMU/IOMMU MP Cache MP Memory Serial Ports SunDiagnostic Executive 2.
PAGE 92
Sun4/II: Trouble - Diagnostics - Sun Diagnostics 3.2 Notes 1. Sun Diagnostics 3.2 was released in July 1993. 2. This is the last field release of the SunDiagnostic Executive. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00712.htm (2 von 2) [25.04.
PAGE 93
Sun4/II: Trouble - Diagnostics - Loopback Connectors Loopback Connectors RS-232/RS-423 PART # SYSTEM BOARDS CONNECT PINS 540-1281-01 CPU,SCSI, and ALM 2-3 4-5 6-20 540-1558-01 CPU, SCSI, ALM, ALM-2, 2-3 4-5 6-8-20 MCP, and SPC/S 17-24 RS-449 PART # SYSTEM BOARDS CONNECT PINS 540-1559-01 MCP 4-6 7-9 8-17 22-24 25-27 11-12-13 29-30-31 35-26 Parallel Port PART # SYSTEM BOARDS CONNECT PINS 540-1560-01 ALM-2 1-10 12-2-4-6-8 13-3-5-7-9 501-1196-01 IPC 5-15 6-13 7-12 8-10 9-11 SBus Printer Board PART # DESCRIP
PAGE 94
Sun4/II: Trouble - Diagnostics - Loopback Connectors 370-1366-01 96-Pin High-Density Loopback Connector 540-1558-01 RS-232/RS-423 Loopback Test Plug Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00713.htm (2 von 2) [25.04.
PAGE 95
Sun4/II: Trouble - Disk - Contents Disk SunOS 4.x SCSI Targets Solaris 2.1 and 2.2 SCSI Targets Solaris 2.3 SCSI Targets SCSI Disk Drives Single-ended 8-bit SCSI Pinouts Media Defect Management SCSI Option Bit SCSI Sense Keys SCSI Sense Codes IPI Disk Drive 1.3GB IPI Physical and Logical Geometry IPI Disk Controller ISP-80 Disk Controller Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004e4.htm [25.04.
PAGE 96
Sun4/II: Trouble - Disk - SunOS 4.x SCSI Targets SunOS 4.x SCSI Targets Sun-4/330 on SunOS 4.x SCSI DEVICE TARGET ID UNIX ID 1st Internal Disk 3 sd6 2nd Internal Disk 1 sd2 1st Internal Tape 4 st0 1st External Tape 4 st0 2nd External Tape 5 st1 CD-ROM 6 sr0 BOOT ID sd(0,18,0) sd(0,8,0) st(0,0,0) st(0,0,0) st(0,28,0) st(0,30,1) Sun-4/370/470 and Sun-3/470 on SunOS 4.
PAGE 97
Sun4/II: Trouble - Disk - SunOS 4.x SCSI Targets 1st Tape 2nd Tape 3rd Tape 4th Tape CD-ROM 1st Tape 2nd Tape 3rd Tape 4th Tape 1st SCSI 1st SCSI 1st SCSI 1st SCSI 1st SCSI 2nd SCSI 2nd SCSI 2nd SCSI 2nd SCSI 4 5 3 2 6 4 5 3 2 st0 st1 st2 st3 sr0* st2 st3 st6 st7 st(0,0,0) st(0,28,0) st(0,18,0) st(0,10,0) st(0,30,1) st(1,0,0) st(1,28,0) st(1,18,0) st(1,10,0) * The Sun 4300 CPU requires EPROM 3.0.2 to boot from CD-ROM. The Sun 4400 CPU requires EPROM 3.
PAGE 98
Sun4/II: Trouble - Disk - Solaris 2.1 and 2.2 SCSI Targets Solaris 2.1 and 2.2 SCSI Targets Solaris 2.1 and 2.2 allow any SCSI device to be assigned any Target number. This chart shows the default target numbers for sd and st devices that are symbolic links from /dev (SunOS 4.x) to /devices (Solaris 2.x).
PAGE 99
Sun4/II: Trouble - Disk - Solaris 2.1 and 2.2 SCSI Targets 33 34 35 36 37 38 39 231 - 234 238 - 241 245 - 248 252 - 255 259 - 262 266 - 269 273 - 276 235 - 236 242 - 243 249 - 250 256 - 257 263 - 264 270 - 271 277 - 278 237 244 251 258 265 272 279 Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00715.htm (2 von 2) [25.04.
PAGE 100
Sun4/II: Trouble - Disk - Solaris 2.3 SCSI Targets Solaris 2.3 SCSI Targets Solaris 2.3 allows any SCSI device to be assigned any Target number. This chart shows the default target numbers for sd and st devices that are symbolic links from /dev (SunOS 4.x) to /devices (Solaris 2.x).
PAGE 101
Sun4/II: Trouble - Disk - Solaris 2.3 SCSI Targets 33 34 35 36 37 38 39 495 - 509 510 - 524 525 - 539 540 - 554 555 - 569 570 - 584 585 - 599 499 - 500 514 - 515 529 - 530 544 - 545 559 - 560 574 - 575 589 - 590 501 516 531 546 561 576 591 Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00716.htm (2 von 2) [25.04.
PAGE 102
Sun4/II: Trouble - Disk - Single-ended 8-bit SCSI Pinouts Single-ended 8-bit SCSI Pinouts SIGNAL DD-50P HD-50 DD-50SA HD-68 -DB(0) 2 26 34 40 -DB(1) 4 27 2 41 -DB(2) 6 28 19 42 -DB(3) 8 29 36 43 -DB(4) 10 30 4 44 -DB(5) 12 31 21 45 -DB(6) 14 32 38 46 -DB(7) 16 33 6 47 -DB(P) 18 34 23 48 GND 20 35 40 49 GND 22 36 8 50 GND 24 37 Res 25 51 Opn TPWR 26 38 42 52 GND 28 39 Res 10 53 GND 30 40 27 54 -ATN 32 41 44 55 GND 34 42 12 56 BSY 36 43 29 57 -ACK 38 44 46 58 -RST 40 45 14 59 -MSG 42 46 31 60 -SEL 44 47 48 6
PAGE 103
Sun4/II: Trouble - Disk - Single-ended 8-bit SCSI Pinouts Notes 1. On HD50 cables, Pins 12, 14, 37, and 39 are reserved and Pin 13 is open. 2. On HD50 to HD68 cables, Pins 1, 2, 3, 4, 5, 17, 18, 31, 32, 33, 34, 35, 36, 37, 38, 39, 51, 65, 66, 67, and 68 are open. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00719.htm (2 von 2) [25.04.
PAGE 104
Sun4/II: Trouble - Disk - Media Defect Management Media Defect Management Embedded SCSI Disk Drives The FORMAT UNIT command formats the media so that all data blocks can be accessed. The following lists are used during the defect management process. Primary, or Manufacturer's, Defect List (P list) The P list supplied by the manufacturer is resident on the disk drive. The initiator can reference this list with the READ DEFECT DATA command. The initiator cannot change or erase the Primary list.
PAGE 105
Sun4/II: Trouble - Disk - SCSI Option Bit SCSI Option Bit SCSI Option Bit Setting Use the following procedure to determine the SCSI option bit setting under Solaris 2.x: # adb -k /kernel/unix /dev/mem (Solaris 2.0 - 2.4) # adb -k /dev/ksyms /dev/mem (Solaris 2.
PAGE 106
Sun4/II: Trouble - Disk - SCSI Sense Keys SCSI Sense Keys KEY DESCRIPTION 0 NO SENSE There is no specific sense key information to be reported for the designated logical unit. This would be the case for a successful command or a command that received CHECK CONDITION or COMMAND TERMINATED status because one of the filemark, EOM, or ILI bits is set to one. 1 RECOVERED DATA The last command completed successfully with some recovery action performed by the target.
PAGE 107
Sun4/II: Trouble - Disk - SCSI Sense Keys c d e f HARDWARE ERROR The target detected a non-recoverable hardware failure while performing the command or during self test. VOLUME OVERFLOW A buffered peripheral device has reached the end-of-partition and data may remain in the buffer that has not been written to the medium. MISCOMPARE The source data did not match the data read from the medium. Reserved Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.
PAGE 108
Sun4/II: Trouble - Disk - SCSI Sense Codes SCSI Sense Codes BYTE 12 - 13 00 00 00 01 00 02 00 03 00 04 00 05 00 11 00 12 00 13 00 14 00 15 01 00 02 00 03 00 03 01 03 02 04 00 04 01 04 02 04 03 04 04 05 00 06 00 07 00 08 00 08 01 08 02 09 00 09 01 09 02 09 03 0a 00 0c 00 0c 01 0c 02 DESCRIPTION Additional Sense Code (ASC) Additional Sense Code Qualifier (ASCQ) No additional sense information Filemark detected End of partition/medium detected Setmark detected Begining-of-Partition/Medium detected End of dat
PAGE 109
Sun4/II: Trouble - Disk - SCSI Sense Codes 10 11 11 11 11 11 11 11 11 11 11 11 12 13 14 14 15 15 15 16 17 17 17 17 17 17 17 18 18 18 18 18 19 19 19 19 1a 1b 1c 1c 1c 00 00 01 02 03 04 05 06 07 08 09 0a 00 00 00 01 00 01 02 00 00 01 02 03 04 05 06 00 01 02 03 04 00 01 02 03 00 00 00 01 02 ID CRC or ECC error Unrecovered read error Read retries exhausted Error log too long to correct Multiple read errors Unrecovered read error - auto reallocate failed L-EC uncorrectable error CIRC unrecovered error Data re
PAGE 110
Sun4/II: Trouble - Disk - SCSI Sense Codes 1d 1e 20 21 21 22 24 25 26 26 26 26 27 28 28 29 2a 2a 2a 2b 2c 2c 2c 2d 2f 30 30 30 30 31 31 32 32 33 36 37 39 3a 3b 3b 3b 00 00 00 00 01 00 00 00 00 01 02 03 00 00 01 00 00 01 02 00 00 01 02 00 00 00 01 02 03 00 01 00 01 00 00 00 00 00 00 01 02 Miscompare during verify operation Recovered ID with ECC correction Invalid command operation code Logical block address out of range Invalid element address Illegal function for device type Invalid field in CDB Logical
PAGE 111
Sun4/II: Trouble - Disk - SCSI Sense Codes 3b 3b 3b 3b 3b 3b 3b 3b 3b 3b 3b 3b 3d 3e 3f 3f 3f 3f 40 41 42 43 44 45 46 47 48 49 4a 4b 4c 4e 50 50 50 51 52 53 53 53 54 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 00 00 00 01 02 03 nn 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 02 00 00 00 01 02 00 Tape or electronic vertical forms unit not ready Slew failure Paper jam Failed to sense top of form Failed to sense bottom of form Reposition error Read past end of medium Read past begining of medium Position past end o
PAGE 112
Sun4/II: Trouble - Disk - SCSI Sense Codes 55 57 58 59 5a 5a 5a 5a 5b 5b 5b 5b 5c 5c 5c 60 61 61 62 63 64 00 00 00 00 00 01 02 03 00 01 02 03 00 01 02 00 01 02 00 00 00 System resource failure Unable to recover table-of-contents Generation does not exist Updated block read Operator request or state change input Operator medium removal request Operator selected write protect Operator selected write permit Log exception Threshold condition met Log counter at maximum Log list codes exhausted RPL status chan
PAGE 113
Sun4/II: Trouble - Disk - 1.3GB IPI Disk Drive 1.3GB IPI Disk Drive Physical and Logical Geometry The 1.3GB IPI Disk Drive uses Zone Bit Recording (ZBR). The outer tracks have a higher bit density than the inner tracks. The defect list for the 1.3GB IPI Disk Drive is in physical block number. Errors reported under the operating system format utility are in logical block number. Block numbers converted to cylinder/head/sector by the show command, are in logical block number.
PAGE 114
Sun4/II: Trouble - Disk - 1.3GB IPI Disk Drive 10 11 12 13 1601 1801 1901 2001 1800 1900 2000 2100 2007326 2218126 2320126 2418726 1513/13/74 1672/13/40 1749/12/16 1824/1/24 2218125 2320125 2418725 2512769 1672/13/39 1749/12/15 1824/1/23 1894/16/77 62 60 58 58 1054 1020 986 986 1.
PAGE 115
Sun4/II: Trouble - Disk - 1.3GB IPI Disk Drive To find the Physical Sector The function of the Modulus Operator % is to give the remainder of the first value divided by the second value. Calculator Conversion of Physical to Logical Block LBN - First Block = LB 1000000 - 929526 = 70474 To find the Physical Cylinder First Cylinder + (LB ÷ Cylinder Size in blocks) = Pcylinder 701 + (70474 ÷ 1292) = Pcylinder 701 + (54.54644) = 755.54644 755 = Pcylinder (0.54644 = Pcylinder remainder) http://lios.apana.
PAGE 116
Sun4/II: Trouble - Disk - 1.3GB IPI Disk Drive To find the Physical Head (Pcylinder remainder × Cylinder size) ÷ Track Size = Phead (0.54644 × 1292) ÷ 76 = Phead (706.00048) ÷ 76 = 9.28948 9 = Phead (0.28948 = Phead remainder) To find the Physical Sector Phead remainder × Track Size = Psector 0.28948 × 76 = Psector 0.28948 × 76 = 22.00048 22 = Psector Logical block 1000000 is located at physical cylinder 755, head 9, sector 22. Add the physical block number to the defect list.
PAGE 117
Sun4/II: Trouble - Disk - SP-80 Disk Controller (IPI-2) ISP-80 Disk Controller Self-Test Error Codes LED 7 lights to indicate a failed self-test http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071f.htm (1 von 2) [25.04.
PAGE 118
Sun4/II: Trouble - Disk - SP-80 Disk Controller (IPI-2) Diagnostic Engineering Monitor The Diagnostic Engineering Monitor (DEMON) is entered when the Diag/Norm switch is in the Diag position. POSITION SYSTEM ACTIVITY DIAG Enters DEMON mode when Self-test is completed. Self-test output is monitored by connecting the ISP-80 controller to a terminal set to 9600 baud, 8 data bits, no parity, and 1 stop bit. The ISP-80 Controller serial port is a 25-pin, dual in-line, header-type connector.
PAGE 119
Sun4/II: Troubleshooting - CPU - Contents CPU Sun-4 Architecture Sun 4100 Sun 4200 Sun 4300 Sun 4300 Address Decoding Sun 4400 Interrupt Levels Sun-4 / Sun-4c / Sun-4m Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004e1.htm [25.04.
PAGE 120
Sun4/II: Troubleshooting - CPU - Sun 4100 Self-Test Error Codes Sun 4100 Self-Test Error Codes http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ff.htm (1 von 2) [25.04.
PAGE 121
Sun4/II: Troubleshooting - CPU - Sun 4100 Self-Test Error Codes Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ff.htm (2 von 2) [25.04.
PAGE 122
Sun4/II: Troubleshooting - CPU - Sun 4200 Self-Test Error Codes Sun 4200 Self-Test Error Codes http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00700.htm (1 von 2) [25.04.
PAGE 123
Sun4/II: Troubleshooting - CPU - Sun 4200 Self-Test Error Codes Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00700.htm (2 von 2) [25.04.
PAGE 124
Sun4/II: Troubleshooting - CPU - Sun 4300 Self-Test Error Codes Sun 4300 Self-Test Error Codes http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00701.htm (1 von 2) [25.04.
PAGE 125
Sun4/II: Troubleshooting - CPU - Sun 4300 Self-Test Error Codes Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00701.htm (2 von 2) [25.04.
PAGE 126
Sun4/II: Troubleshooting - CPU - Sun 4300 Address Decoding Sun 4300 Address Decoding The physical address and the byte in error are used to determine a failing SIMM module. Socket locations are silkscreened on the component side of the CPU and 3U Memory Boards, and on the solder side of the 9U Memory Board. This section includes examples of errors and charts for the Sun 4300 CPU, 3U Memory Boards and 9U Memory Boards.
PAGE 127
Sun4/II: Troubleshooting - CPU - Sun 4300 Address Decoding 4-8MB 000000-7fffff 1 1 U1307 Sun 4300 Address Decoding 1st 3U Memory Board Addressing ADDRESS (Dec) 8-12MB 8-12MB 8-12MB 8-12MB 12-16MB 12-16MB 12-16MB 12-16MB 16-20MB 16-20MB 16-20MB 16-20MB 20-24MB 20-24MB 20-24MB 20-24MB ADDRESS (Hex) BANK BYTE SOCKET 800000-bfffff 0 0 U1600 800000-bfffff 0 1 U1601 800000-bfffff 0 2 U1602 800000-bfffff 0 3 U1603 c00000-ffffff 1 0 U1604 c00000-ffffff 1 1 U1605 c00000-ffffff 1 2 U1606 c00000-ffffff 1 3 U160
PAGE 128
Sun4/II: Troubleshooting - CPU - Sun 4300 Address Decoding 36-40MB 36-40MB 2400000-27fffff 2400000-27fffff 3 3 2 3 U1706 U1707 1st 24 Mbytes of 9U Memory Board Addressing ADDRESS (Dec) 8-12MB 8-12MB 8-12MB 8-12MB 12-16MB 12-16MB 12-16MB 12-16MB 16-20MB 16-20MB 16-20MB 16-20MB 20-24MB 20-24MB 20-24MB 20-24MB 24-28MB 24-28MB 24-28MB 24-28MB 28-32MB 28-32MB 28-32MB 28-32MB ADDRESS (Hex) BANK BYTE SOCKET 800000-bfffff 0L 0 U1600 800000-bfffff 0L 1 U1601 800000-bfffff 0L 2 U1602 800000-bfffff 0L 3 U1603 c
PAGE 129
Sun4/II: Troubleshooting - CPU - Sun 4300 Address Decoding 36-40MB 40-44MB 40-44MB 40-44MB 40-44MB 44-48MB 44-48MB 44-48MB 44-48MB 48-52MB 48-52MB 48-52MB 48-52MB 52-56MB 52-56MB 52-56MB 52-56MB 2400000-27fffff 2800000-2bfffff 2800000-2bfffff 2800000-2bfffff 2800000-2bfffff 2c00000-2ffffff 2c00000-2ffffff 2c00000-2ffffff 2c00000-2ffffff 3000000-33fffff 3000000-33fffff 3000000-33fffff 3000000-33fffff 3400000-1ffffff 3400000-1ffffff 3400000-1ffffff 3400000-1ffffff 3H 4L 4L 4L 4L 4H 4H 4H 4H 5L 5L 5L 5L 5H
PAGE 130
Sun4/II: Troubleshooting - CPU - Sun 4400 Self-Test Error Codes Sun 4400 Self-Test Error Codes http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00703.htm (1 von 2) [25.04.
PAGE 131
Sun4/II: Troubleshooting - CPU - Sun 4400 Self-Test Error Codes Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00703.htm (2 von 2) [25.04.
PAGE 132
Sun4/II: Troubleshooting - CPU - Interrupt Levels Interrupt Levels SPARC Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9 Level 10 Level 11 Level 12 Level 13 Level 14 Level 15 Sun-4 SW1 VME1 VME2 SW4, SCSI VME3 SW6, Ethernet VME4 Video VME5 System C/T VME6 KBD/MS/SCC VME7 Kernet C/T Memory Error Sun-4c Sun-4m SW1 SBus2 SBus3, SCSI SW4 SBus4, Ethernet SW6 SBus5, Video SBus6 SBus7 System C/T Floppy KBD/MS/SCC Audio Kernel C/T Async Mem Error SW1 SW2, VME1, SBus1 SW3, VME2, SBus2 S
PAGE 133
Sun4/II: Parts - Printer - Contents Printer Connector Pinouts SBus Printer Card SPARCprinter Printers LaserWriter II SPARCprinter Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004dd.htm [25.04.
PAGE 134
Sun4/II: Parts - Printer - Pinouts Connector Pinouts SBus Printer Card 501-1540 Video Port SBus Printer Card 501-1910 Video Port 20-Pin to 25-Pin Cable 370-1365 20-Pin Hi-Density Female PIN SIGNAL PIN SIGNAL 1 VCLK+ 11 VCLK2 LSYNC+ 12 LSYNC3 STATUS+ 13 STATUS4 PSYNC+ 14 PSYNC5 Do not use 15 Do not use 6 Do not use 16 Do not use 7 Do not use 17 Do not use 8 CBUSY- 18 CBUSY+ 9 CMD+ 19 CMD10 VDATA+ 20 VDATASBus Printer Card 501-1540 Parallel Port SBus Printer Card 501-1910 Parallel Port 28-Pin to 28-Pin Cable
PAGE 135
Sun4/II: Parts - Printer - Pinouts Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00674.htm (2 von 2) [25.04.
PAGE 136
Sun4/II: Parts - Printer - SPARCprinter Connector Pinouts SPARCprinter 20-Pin to 25-Pin Cable 370-1365 25-Pin Female D-Sub PIN 1 5 7 11 23 9 3 SIGNAL VCLK+ LSYNC+ STATUS+ PSYNC+ CBUSYCMD+ VDATA+ PIN 14 18 20 24 13 22 16 SIGNAL VDATA+ LSYNCLSYNCPSYNCCBUSY+ CMDVDATA- Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00675.htm [25.04.
PAGE 137
Sun4/II: Parts - Printer - LaserWriter II LaserWriter II LW-1 LW-2 LW-3 115V LaserWriter 240V LaserWriter 115V LaserWriter A4 Paper Tray PART # 365-1040 370-1189 370-1196 536-1003 350-1015 330-1162 330-1163 365-1041 370-1188 370-1196 536-1002 350-1014 330-1160 330-1161 365-1067 370-1188 370-1196 536-1002 350-1015 330-1162 330-1163 150-1279 530-1172 530-1433 DESCRIPTION LaserWriter II Assembly, A4 Paper Tray (240V) LaserWriter II Print Engine (240V) NT Controller PCA AC Power Cord (240V) A4 Paper Tray A
PAGE 138
Sun4/II: Parts - Printer - SPARCprinter SPARCprinter Option SPRN-400 Xerox 4030 PART # 365-1089 365-1124 365-1125 365-1126 365-1127 370-1365 410-1017 501-1540 530-1680 530-1683 530-1694 811-1345 811-1316 811-1687 DESCRIPTION SPARCprinter (115V & 240V) Toner Cartridge 1 Drum Cartridge 2 Universal Paper Tray B4 Paper Tray Video Port Cable, Video Port to SPARCprinter Reusable Field Service Transit Case SBus Printer Board Parallel Port Cable Loopback Test Cable, Parallel Port to Video Port Test Cable, Video P
PAGE 139
Sun4/II: Parts - Printer - SPARCprinter SPARCprinter IOT Test Print 1. 2. 3. 4. Switch the printer OFF. Press and hold TEST. Switch the printer ON. Release TEST. 00 is displayed. The printer must warm-up for approximately one minute in order to print a test page. 5. Press ENTER to start printing the IOT test print. The display indicates the number of test pages printed. 6. Press ENTER to stop printing the IOT test print. 7. Switch the printer OFF to exit the IOT Test Print Mode.
PAGE 140
Sun4/II: Parts - Printer - SPARCprinter SPARCprinter Output Component Tests 1. 2. 3. 4. Switch the printer OFF. Press and hold ENTER. Switch the printer ON. Press TEST until the desired diagnostic test number is displayed in the Operator Panel. The following output components can be tested: Component Test Code Print Counter 30 Upper Feed Clutch 80 Lower Feed Clutch 81 Registration Clutch 82 Upper Turn Roll Clutch 84 Lower Turn Roll Clutch 84 Main Motor & Erase Lamp 90 HVPS 90 5.
PAGE 141
Sun4/II: Parts - Printer - SPARCprinter Configuration Paper matrix Console Type 7 8 9 xx 3 xx 4 xx 4 1. Processing Direction controls the top and bottom page margin. Each increment from 0 to F adjusts the margin 0.5 mm. 2. Scanning Direction controls the left and right page margin. Each increment from 0 to 8 adjusts the margin 0.5 mm. 3. Press ENTER to print one test page. 4. Do NOT change these factory settings.
PAGE 142
Sun4/II: Parts - Monitor - Contents Monitor Monitor and Image Size Connector Pinouts Cables 12-inch Color LCD 14-inch Color CRT 14-inch Color Entry-Level CRT 14-inch Monochrome LCD 15-inch Color CRT 15-inch Monochrome CRT 16-inch Color CRT 16-inch Premium Color CRT 16-inch Mid-Range Color CRT 17-inch Premium Color CRT 17-inch Entry-Level Color CRT 17-inch Greyscale CRT 19-inch Color CRT 19-inch Premium Color CRT 19-inch Greyscale CRT 19-inch Greyscale CRT with OCLI 19-inch Monochrome CRT 19-inch Monochrome
PAGE 143
Sun4/II: Parts - Monitor - Monitor and Image Size Monitor and Image Size Monitor size is the diagonal dimension of the CRT or the diagonal dimension of the CRT phosphor coating. The image size of monitors may not be reflected in the monitor size listed in sales documents or price lists. Image size is the horizontal and vertical dimension of the active display. The image size, or active display, is smaller than the CRT, Bezel, and Margin.
PAGE 144
Sun4/II: Parts - Monitor - Connector Pinouts Connector Pinouts Monochrome CRT 9-Pin Female D-Sub PIN 1 2 3 4 5 SIGNAL VIDEO+ GND HSYNC VSYNC Not used PIN 6 7 8 9 SIGNAL VIDEOGND GND GND Color CRT DB13W3 PIN 1 2 3 4 5 6 7 SIGNAL Monitor specific Monitor specific SENSE2 SRTN CSYNC Monitor specific Monitor specific PIN 8 9 10 A1 A2 A3 SIGNAL SENSE1 SENSE0 CRTN Red Green Blue Pins 1, 2, 6, and 7 are GND on the SBus GX+. Pin-2 is VSYNC and Pin-6 is HSYNC on the SBus CG3.
PAGE 145
Sun4/II: Parts - Monitor - Connector Pinouts 7 Monitor specific Color CRT HD15 Connector PIN 1 2 3 4 5 6 7 8 SIGNAL Red Green Blue Not used Not used Red Gnd Green Gnd Blue Gnd PIN 9 10 11 12 13 14 15 SIGNAL Not used Sync Gnd Gnd DDC Data Hsync Hsync DDC Clock Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00652.htm (2 von 2) [25.04.
PAGE 146
Sun4/II: Parts - Monitor - Cables Video Cables PART # 530-0492 530-1138 530-1307 530-1362 530-1415 530-1440 530-1446 530-1509 530-1839 530-1840 530-1870 530-1898 530-2020 530-2357 DESCRIPTION Color CRT Cable, 4.6M, 1xBNC to 1xBNC Color CRT Cable, 4.6M, 4xBNC to 4xBNC Color CRT Cable, 4.6M, 4xBNC to 4xBNC Color CRT Cable, 1.2M, 4xBNC to 4xBNC Color CRT Cable, 50 cm, 4xBNC to 4xBNC Color CRT Cable, 1.2M, DB13W3 to DB13W3 Color CRT Video Adapter Cable, 4xBNC to DB13W3 Color CRT Cable, 4.
PAGE 147
Sun4/II: Parts - Monitor - 12-inch Color LCD 12-inch Color LCD Image Size: 239 mm Horizontal 179 mm Vertical 299 mm Diagonal Pixel Horizontal Vertical Data Resolution Frequency Frequency Clock 1024 x 768 51.9KHz 67.2Hz 27MHz* PART # DESCRIPTION 540-2452 12" Color LCD * The effective Pixel Rate for the 27.000MHz Data Clock is 54.000MHz. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00654.htm [25.04.
PAGE 148
Sun4/II: Parts - Monitor - 14-inch Color CRT 14-inch Color CRT Image Size: 244 mm Horizontal 183 mm Vertical 305 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1024 x 768 53.6KHz 66Hz 70.
PAGE 149
Sun4/II: Parts - Monitor - 14-inch Color CRT S2 is grounded. The Sense Code is 3. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00655.htm (2 von 2) [25.04.
PAGE 150
Sun4/II: Parts - Monitor - 14-inch Entry-Level Color CRT 14-inch Entry-Level Color CRT Image Size: 255 mm Horizontal 191 mm Vertical 319 mm Diagonal Pixel Resolution 800 x 600 1024 x 768 Horizontal Frequency 46.875KHz 48.363KHz Vertical Pixel Frequency Frequency 75.000Hz 49.50MHz 60.004Hz 65.00MHz PART # DESCRIPTION Samsung CQB4157L, .
PAGE 151
Sun4/II: Parts - Monitor - 14-inch Monochrome LCD 14-inch Monochrome LCD Image Size: 274 mm Horizontal 214 mm Vertical 347 mm Diagonal Pixel Horizontal Vertical Data Resolution Frequency Frequency Clock 1152 x 900 64.5KHz 60.2Hz 4.9MHz * PART # DESCRIPTION 540-2453 14" Monochrome LCD * The effective Pixel Rate for the 4.9091MHz Data Clock is 78.5456MHz. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00657.htm [25.04.
PAGE 152
Sun4/II: Parts - Monitor - 15-inch Color CRT 15-inch Color CRT Image Size: 262 mm Horizontal 200 mm Vertical 329 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1152 x 900 61.8KHz 66Hz 92.
PAGE 153
Sun4/II: Parts - Monitor - 15-inch Color CRT 15-inch Color CRT Image Size: 260 mm Horizontal 195 mm Vertical 325 mm Diagonal Pixel Resolution 1152 x 900 1024 x 768 Horizontal Vertical Pixel Frequency Frequency Frequency 61.8KHz 66Hz 92.5MHz 62.0KHz 77Hz 84.37MHz PART # DESCRIPTION Nokia 449A101, .28 mm Dot-Pitch 365-1286 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, ELF/VLF with non-removable 1.2M Video Cable Nokia 449A101, .
PAGE 154
Sun4/II: Parts - Monitor - 15-inch Monochrome CRT 15-inch Monochrome CRT Image Size: 250 mm Horizontal 187 mm Vertical 312 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1024 x 768 63.96KHz 76Hz 85.
PAGE 155
Sun4/II: Parts - Monitor - 16-inch Color CRT 16-inch Color CRT Image Size: 295 mm Horizontal 230 mm Vertical 374 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1152 x 900 61.8KHz 66Hz 92.94MHz PART # DESCRIPTION 365-1020 115V Sony P2 GDM-1604-15 Monitor, 4xBNC 150-1225 Fuse, 4A 180-1146 Power Cord, IEC 320/CEE 22 to NEMA 5-15 365-1022 240V Sony P2 GDM-1604-40 Monitor, 4xBNC 150-1226 Fuse, 3.
PAGE 156
Sun4/II: Parts - Monitor - 16-inch Color CRT Philips/Fimi C1764 SPARCstation IPC Option LPC 365-1143 115V Monitor, DB13W3, FCC-B/VCCI-2 Philips/Fimi C1764 SPARCstation IPC Option LPC 365-1146 240V Monitor, DB13W3, FCC-B/VCCI-2 Notes 1. S0 and S1 are grounded. The Sense Code is 4. 2. DB13W3 Pins 1, 2, 6, and 7 are not used.
PAGE 157
Sun4/II: Parts - Monitor - 16-inch Premium Color CRT 16-inch Premium Color CRT Image Size: 295 mm Horizontal 230 mm Vertical 374 mm Diagonal Pixel Resolution 944 x 736 1076 x 824 1152 x 900 1152 x 900 Horizontal Vertical Pixel Frequency Frequency Frequency 70.8KHz 84Hz 92.94MHz * 71.7KHz 76Hz 105.5MHz ** 61.8KHz 66Hz 92.94MHz 71.7KHz 76Hz 105.5MHz PART # DESCRIPTION Sony P3 GDM-1662, .31 mm Dot-Pitch 365-1096 115V/240V Monitor, DB13W3, FCC-A/VCCI-1 (not used) Sony P3 GDM-1662 or GDM-1662B, .
PAGE 158
Sun4/II: Parts - Monitor - 16-inch Premium Color CRT P4 CG6, 501-1532-09 and below SBus CG6, 501-1481-04 and below SBus CG6 501-1645-03 and below. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0065b.htm (2 von 2) [25.04.
PAGE 159
Sun4/II: Parts - Monitor - 16-inch Mid-Range Color CRT 16-inch Mid-Range Color CRT Image Size: 95 mm Horizontal 226 mm Vertical 371 mm Diagonal Pixel Resolution 1152 x 900 1024 x 768 Horizontal Vertical Pixel Frequency Frequency Frequency 61.8KHz 66Hz 92.94MHz 62.0KHz 77Hz 84.37MHz PART # 365-1151 365-1164 365-1165 365-1166 DESCRIPTION Sony CPD-1790 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, with non-removable 1.2M Video Cable 115V/240V S. Hemisphere Monitor, DB13W3, FCC-B/VCCI-2, with non-removable 1.
PAGE 160
Sun4/II: Parts - Monitor - 16-inch Mid-Range Color CRT 70MHz 85MHz 85MHz 110MHz 110MHz 110MHz >=501-3002-02 >=501-2549-03 >=501-2928-02 >=501-3008-03 501-3109-xx 501-3134-xx Yes Yes Yes Yes Yes 2 Yes 2 Notes: 1. If the SPARCstation 4 tcx frame buffer outputs sync on green, the board is not compatible with the 16-inch monitor. The monitor can not remove sync from the green output. Sync on green causes a higher than normal green output level. Refer to BugID 1218690. 2.
PAGE 161
Sun4/II: Parts - Monitor - 17-inch Premium Color CRT 17-inch Premium Color CRT Image Size: 300 mm Horizontal 234 mm Vertical 380 mm Diagonal Pixel Resolution 1152 x 900 1280 x 1024 Horizontal Frequency 71.81KHz 81.13KHz Vertical Pixel Frequency Frequency 76.14Hz 108MHz 76.11Hz 135MHz PART # DESCRIPTION Sony N1 GDM-17E10, .26 mm Dot-Pitch 365-1316 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, with non-removable 1.2M Video Cable Sony N1 GDM-17E10, .
PAGE 162
Sun4/II: Parts - Monitor - 17-inch Premium Color CRT 17-inch Premium Color CRT Image Size: 300 mm Horizontal 225 mm Vertical 375 mm Diagonal Image Size: 293 mm Horizontal 234 mm Vertical 375 mm Diagonal PART # DESCRIPTION Sony N2 GDM17E20, .26 mm Dot-Pitch 365-1338 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, with non-removable 1.2M Video Cable Sony N2 GDM17E20, .26 mm Dot-Pitch 365-1339 115V/240V OEM Monitor, DB13W3, FCC-B/VCC1-2 with non-removable 1.2 Video Cable Sony N2 GDM17E20, .
PAGE 163
Sun4/II: Parts - Monitor - 17-inch Entry-Level Color CRT 17-inch Entry-Level Color CRT Image Size: 300 mm Horizontal 225 mm Vertical 375 mm Diagonal Pixel Resolution 1152 x 900 1024 x 768 Horizontal Vertical Pixel Frequency Frequency Frequency 61.8KHz 66Hz 94.5MHz 62.0KHz 77Hz 84.3MHz PART # DESCRIPTION Nokia, .28 mm Dot-Pitch 365-1343 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, with non-removable 1.2M Video Cable Nokia, .
PAGE 164
Sun4/II: Parts - Monitor - 17-inch Entry-Level Color CRT 85MHz >=501-2928-02 110MHz >=501-3008-03 110MHz 501-3109-xx 110MHz 501-3134-xx Yes Yes Yes 2 Yes 2 Notes 1. If the SPARCstation 4 tcx frame buffer outputs sync on green, the board is not compatible with the 17-inch monitor. The monitor can not remove sync from the green output. Sync on green causes a higher than normal green output level. Refer to BugID 1218690. 2. Jumper J0501 on the SS4 CPU enables or disables sync on green.
PAGE 165
Sun4/II: Parts - Monitor - 17-inch Greyscale CRT 17-inch Greyscale CRT Image Size: 295 mm Horizontal 230 mm Vertical 374 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1152 x 900 61.8KHz 66Hz 92.
PAGE 166
Sun4/II: Parts - Monitor - 17-inch Greyscale CRT Zenith 17SMM4-A 365-1157 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, with Video Cable 530-1870 * The Mode III (1024 x 800 @ 84) Overscan Mode user area is 914 x 690. ** The Mode II (1152 x 900 @ 76) Overscan Mode user area is 1024 x 780. DB13W3 Connector PIN 1 2 3 4 5 6 7 SIGNAL Not used Not used Sense2 Sgnd Csync Not used Not used PIN 8 9 10 A1 A2 A3 SIGNAL Sense1 Sense0 Cgnd Not used Green Not used S2 is grounded. The Sense Code is 3.
PAGE 167
Sun4/II: Parts - Monitor - 19-inch Color CRT 19-inch Color CRT Image Size: 255 mm Horizontal 280 mm Vertical 452 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1152 x 900 61.8KHz 66Hz 92.94MHz PART # 540-1094 140-1022 180-1097 360-1008 365-1000 140-1022 180-1097 180-1146 365-1006 140-1034 150-1051 180-1125 365-1056 140-1022 180-1146 365-1054 140-1034 150-1051 180-1125 365-1073 365-1038 150-1225 180-1146 DESCRIPTION Hitachi HM-4619, .
PAGE 168
Sun4/II: Parts - Monitor - 19-inch Color CRT 365-1039 150-1226 180-1125 365-1065 150-1225 365-1066 150-1226 365-1081 150-1225 365-1082 150-1226 Sony P2 GDM-1955A40, .31 mm Dot-Pitch 240V Monitor, 4xBNC Fuse, 3.15A Power Cord, IEC 320/CEE 22 to pigtail Sony P2 GDM-1955A15, .31 mm Dot-Pitch 115V Monitor, DB13W3 Fuse, 4A Sony P2 GDM-1955A40, .31 mm Dot-Pitch 240V Monitor, DB13W3 Fuse, 3.15A Sony P2 GDM-1955A15, .31 mm Dot-Pitch 115V Monitor, DB13W3, FCC-A/VCCI-1 Fuse, 4A Sony P2 GDM-1955A40, .
PAGE 169
Sun4/II: Parts - Monitor - 19-inch Premium Color CRT 19-inch Premium Color CRT Image Size: 350 mm Horizontal 270 mm Vertical 442 mm Diagonal Pixel Resolution 1076 x 824 1152 x 900 1152 x 900 1280 x 1024 Horizontal Vertical Pixel Frequency Frequency Frequency 71.7KHz 76Hz 105.5MHz * 61.8KHz 66Hz 92.94MHz 71.7KHz 76Hz 105.5MHz 71.7KHz 67Hz 117MHz PART # DESCRIPTION Sony P3 GDM-1962, .
PAGE 170
Sun4/II: Parts - Monitor - 19-inch Premium Color CRT Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00661.htm (2 von 2) [25.04.
PAGE 171
Sun4/II: Parts - Monitor - 19-inch Greyscale CRT 19-inch Greyscale CRT Image Size: 350 mm Horizontal 273 mm Vertical 443 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1152 x 900 61.8KHz 66Hz 92.94MHz PART # 540-1343 540-1514 140-1022 180-1097 180-1146 540-1567 150-1215 180-1125 365-1010 140-1022 180-1097 180-1146 DESCRIPTION 115V Monitor, 2xBNC, 395x535 mm Base 115V Monitor, 2xBNC, 395x535 mm Base Fuse, 1.
PAGE 172
Sun4/II: Parts - Monitor - 19-inch Greyscale CRT 1152 x 900 71.7KHz 1076 x 824 71.7KHz PART # 365-1099 365-1108 365-1140 365-1154 76Hz 76Hz 105.5Mhz 105.
PAGE 173
Sun4/II: Parts - Monitor - 19-inch Greyscale CRT with OCLI 19-inch Greyscale CRT with OCLI Image Size: 350 mm Horizontal 273 mm Vertical 443 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1152 x 900 61.8KHz 66Hz 92.94MHz PART # 365-1008 150-1051 150-1215 180-1125 DESCRIPTION Philips M19P114T/6103 240V Monitor, 2xBNC, 395x535 mm Base Fusecarrier Fuse, 1.
PAGE 174
Sun4/II: Parts - Monitor - 19-inch Monochrome CRT 19-inch Monochrome CRT Image Size: 350 mm Horizontal 273 mm Vertical 443 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1152 x 900 61.
PAGE 175
Sun4/II: Parts - Monitor - 19-inch Monochrome CRT 365-1014 150-1051 150-1215 180-1125 365-1051 140-1022 180-1097 180-1146 Elston DM60-19A0-09-A104 240V Monitor, DB9, 395x535 mm Base Fusecarrier Fuse, 1.6A Power Cord, IEC 320/CEE 22 to pigtail Philips M19P114A/612420 115V Monitor, DB9, 409x409 mm Base Fuse, 1.6A Power Cord, IEC 320/CEE 22 to NEMA 5-15 Power Cord, IEC 320/CEE 22 to NEMA 5-15 365-1043 150-1051 150-1215 180-1125 240V Monitor, DB9, 409x409 mm Base Fusecarrier Fuse, 1.
PAGE 176
Sun4/II: Parts - Monitor - 19-inch Monochrome CRT with OCLI 19-inch Monochrome CRT with OCLI Image Size: 350 mm Horizontal 273 mm Vertical 443 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1152 x 900 61.8KHz 66Hz 100MHz PART # DESCRIPTION Philips M19P114A/6115 540-1358 115V Monitor (360-1023), DB9, without Base 140-1022 Fuse, 1.
PAGE 177
Sun4/II: Parts - Monitor - 19-inch Hi-Resolution CRT 19-inch Hi-Resolution CRT Image Size: 355 mm Horizontal 279 mm Vertical 452 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1600 x 1280 89.
PAGE 178
Sun4/II: Parts - Monitor - 19-inch Hi-Resolution CRT with OCLI 19-inch Hi-Resolution CRT with OCLI Image Size: 355 mm Horizontal 279 mm Vertical 452 mm Diagonal Pixel Horizontal Vertical Pixel Resolution Frequency Frequency Frequency 1600 x 1280 89.3KHz 67Hz 200MHz PART # 365-1004 140-1002 180-1097 180-1146 365-1003 150-1051 150-1208 180-1125 DESCRIPTION Motorola L7201S-Y01K 115V Monitor, DB9, 395x535 mm Base Fuse, 3.
PAGE 179
Sun4/II: Parts - Monitor - 20-inch Premium Color CRT 20-inch Premium Color CRT Image Size: 350 mm Horizontal 270 mm Vertical 442 mm Diagonal Pixel Resolution 1076 x 824 1196 x 938 1152 x 900 1152 x 900 1280 x 1024 1280 x 1024 PART # 365-1167 365-1313 365-1317 365-1330 365-1322 365-1324 365-1325 365-1326 370-1576 370-1705 none Horizontal Vertical Pixel Frequency Frequency Frequency 71.7KHz 76Hz 108MHz * 81.1KHz 76Hz 135MHz ** 61.8KHz 66Hz 94.5MHz 71.8KHz 76Hz 108MHz 71.8KHz 67Hz 118MHz 81.
PAGE 180
Sun4/II: Parts - Monitor - 20-inch Premium Color CRT 2 3 4 5 6 RS232 data in Sense2 Sgnd Csync RS232 data out 9 10 A1 A2 A3 Sense0 Cgnd Red Green Blue S0 and S1 are grounded. The Sense Code is 4. Pin-7 is not used. 20-inch Premium Color CRT Image Size: 350 mm Horizontal 270 mm Vertical 442 mm Diagonal Pixel Resolution 960 x 680 1152 x 900 1152 x 900 1280 x 1024 1280 x 1024 PART# 365-1335 365-1337 365-1340 365-1342 Horizontal Frequency 81.13KHz 71.81KHz 61.84KHz 81.13KHz 71.
PAGE 181
Sun4/II: Parts - Monitor - 20-inch Premium Color CRT 6 SDA serial data I/O 7 Vsync A3 Blue S0 and S1 are grounded. The Sense Code is 4. Pin-5 is Hsync if Vsync is present on Pin-7. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00668.htm (3 von 3) [25.04.
PAGE 182
Sun4/II: Parts - Monitor - 20-inch Premium Greyscale CRT 20-inch Premium Greyscale CRT Image Size: 350 mm Horizontal 273 mm Vertical 443 mm Diagonal Pixel Resolution 1152 x 900 1280 x 1024 Horizontal Vertical Pixel Frequency Frequency Frequency 71.8KHz 76Hz 105.5MHz 81.1KHz 76Hz 135MHz PART # DESCRIPTION Zenith 20S5 365-1168 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, MPR 1990:10 with non-removable 1.
PAGE 183
Sun4/II: Parts - Input Device - Contents Input Device SunButtons SunDials Type-3 Keyboard Type-3 Optical Mouse Type-3 to Type-4 Spares Kit Type-4 Keyboard Type-5 Keyboard Type-5c Keyboard Type 101A Keyboard Type-4 Optical Mouse Type-5 Optical Mouse Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004d7.htm [25.04.
PAGE 184
Sun4/II: Parts - Input Device - SunButtons SunButtons Option 180 Wiring Diagram CODE 1 2 3 4 5 6 NS NS PART # DESCRIPTION 595-1865 230V SunButtons Assembly 595-1884 115V SunButtons Assembly 300-1053 115V Power Supply 300-1054 230V Power Supply 370-1291 SunButtons Box 540-1935 RFI Filter, DB-25 530-1610 DB-9M to DB-9F Cable, 600 mm 530-1525 DB-9 to DB-15 to DIN-5 Cable, 2.0M 180-1125 230V AC Power Cord (obsolete) 260-3861 Overlay Template Last updated: December 2, 1996 http://lios.apana.org.
PAGE 185
Sun4/II: Parts - Input Device - SunButtons Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00634.htm (2 von 2) [25.04.
PAGE 186
Sun4/II: Parts - Input Device - SunDials SunDials Option 190 Wiring Diagram 1 2 3 4 5 6 NS NS PART # DESCRIPTION 595-1737 115V SunDials Assembly 595-1773 230V SunDials Assembly 300-1053 115V Power Supply 300-1054 230V Power Supply 370-1223 Dialbox and Bale 540-1935 RFI Filter, DB-25 530-1610 DB-9M to DB-9F Cable, 600 mm 530-1525 DB-9 to DB-15 to DIN-5 Cable, 2.0M 180-1125 230V AC Power Cord (obsolete) 260-3257 Overlay Template Last updated: December 2, 1996 http://lios.apana.org.
PAGE 187
Sun4/II: Parts - Input Device - SunDials Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00635.htm (2 von 2) [25.04.
PAGE 188
Sun4/II: Parts - Input Device - Type-3 Keyboard Type-3 Keyboard PART # DESCRIPTION 370-1063 Type-3 Keyboard, DB-15 (obsolete) 370-1095 Type-3 Keyboard, DB-15 530-1526 Type-3 Keyboard Adapter Cable, DB-15 to Mini-Din Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00636.htm [25.04.
PAGE 189
Sun4/II: Parts - Input Device - Type-3 Optical Mouse Type-3 Optical Mouse PART # DESCRIPTION 370-1058 M3 Mouse and Pad, RJ11 (obsolete) 370-1091 M3 Mouse and Pad, RJ11 (obsolete) 365-1042 M4 Mouse and Pad, RJ11 370-1169 M4 Mouse, 200 CPI, RJ11 370-1171 M4 Mouse Pad, 200 CPI, 0.062", 228.6 x 196.9 mm (obs) 370-1215 M4 Mouse Pad, 200 CPI, 0.032", 228.6 x 196.9 mm (obs) 370-1368 M4 Mouse Pad, 200 CPI, 0.032", 177.8 x 196.9 mm Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.
PAGE 190
Sun4/II: Parts - Input Device - Type-3 to Type-4 Spares Kit Type-3 to Type-4 Spares Kit PART # DESCRIPTION 560-1501 Type 3 Keyboard/Mouse to Type 4 Keyboard/Mouse Kit 320-1005 Type-4 Keyboard, Mini-Din, US 370-1170 M4 200 CPI Mouse, Mini-Din 370-1368 M4 Mouse Pad, 200 CPI, 0.032", 177.8 x 196.9 mm 530-1443 Keyboard Cable, Mini-Din to Mini Din, 4.6M 530-1479 Keyboard Cable, DB-15 to Mini Din, 4.6M Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.
PAGE 191
Sun4/II: Parts - Input Device - Type-4 Keyboard Type-4 Keyboard Underside of Keyboard DESCRIPTION Sun-3/4 w >=4.0 or 386i Sun-3 w <=3.
PAGE 192
Sun4/II: Parts - Input Device - Type-4 Keyboard 320-1007 320-1008 320-1009 320-1010 320-1011 320-1012 320-1013 320-1014 320-1015 320-1016 320-1017 320-1018 Type-4 Keyboard, Mini-Din, Swiss German Type-4 Keyboard, Mini-Din, Belgium and France Type-4 Keyboard, Mini-Din, UK Type-4 Keyboard, Mini-Din, Swiss French Type-4 Keyboard, Mini-Din, Netherlands Type-4 Keyboard, Mini-Din, Sweden and Denmark Type-4 Keyboard, Mini-Din, Denmark Type-4 Keyboard, Mini-Din, Norway Type-4 Keyboard, Mini-Din, Italy Type-4 Keyb
PAGE 193
Sun4/II: Parts - Input Device - Type-5 Keyboard Type-5 Keyboard Underside of Keyboard DESCRIPTION US US/Unix French Danish German Italian Dutch Norwegian Portuguese Spanish Swedish/Finnish Swiss/French Swiss/German UK Korean Taiwanese Nihon-go French Canadian 1 - 2 - DIP SWITCH 3 4 5 6 7 On - - - On - - - On On - - - On On - - On On - - On On - - On On On - - On On On - On - On - On - On - On - On On - On - On On - On On On - On On On - On On On On - On On On On On - - On On - - On On - - On 8 CODE On
PAGE 194
Sun4/II: Parts - Input Device - Type-5 Keyboard 320-1075 320-1076 320-1077 320-1078 320-1079 320-1080 320-1081 320-1082 320-1083 320-1084 320-1085 320-1086 320-1087 320-1088 320-1089 320-1090 320-1091 320-1092 320-1193 Type-5 Keyboard, Mini-Din, Danish Type-5 Keyboard, Mini-Din, German Type-5 Keyboard, Mini-Din, Italian Type-5 Keyboard, Mini-Din, Netherlands/Dutch Type-5 Keyboard, Mini-Din, Norwegian Type-5 Keyboard, Mini-Din, Portuguese Type-5 Keyboard, Mini-Din, Spanish Type-5 Keyboard, Mini-Din, Swedis
PAGE 195
Sun4/II: Parts - Input Device - Type-5c Keyboard Type-5c Keyboard WIRE JUMPER HEX DESCRIPTION JS1 JS2 JS3 JS4 JS5 CODE US - In 21 US/Unix - In 22 Japanese In - In 31 DIP SWITCH HEX DESCRIPTION 1 2 3 4 5 CODE French - - - On On 23 Danish - - On - 24 German - - On - On 25 Italian - - On On 26 Dutch - - On On On 27 Norwegian - On - - 28 Portuguese - On - - On 29 Spanish - On - On 2a Swedish/Finnish - On - On On 2b Swiss/French - On On - 2c Swiss/German - On On - On 2d UK - On On On 2e Korean - On On On On 2f
PAGE 196
Sun4/II: Parts - Input Device - Type-5c Keyboard 320-1234 320-1252 320-1236 320-1237 320-1238 320-1239 320-1240 320-1241 320-1242 320-1243 320-1245 320-1246 320-1247 320-1248 320-1249 320-1253 320-1244 320-1235 320-1250 320-1251 Type-5c Keyboard, 2M Cable, Mini-Din, US/UNIX Type-5c Keyboard, 2M Cable, Mini-Din, French Type-5c Keyboard, 2M Cable, Mini-Din, Danish Type-5c Keyboard, 2M Cable, Mini-Din, German Type-5c Keyboard, 2M Cable, Mini-Din, Italian Type-5c Keyboard, 2M Cable, Mini-Din, Netherlands/ Dut
PAGE 197
Sun4/II: Parts - Input Device - Type-101A Keyboard Type-101A Keyboard Underside of Keyboard PART # DESCRIPTION 320-1070 Type 101A Keyboard, Mini-Din 530-1442 530-1443 530-1478 530-1479 Keyboard Cable, Mini-Din to Mini Din, 2.0M Keyboard Cable, Mini-Din to Mini Din, 4.6M Keyboard Cable, DB-15 to Mini Din, 2.0M Keyboard Cable, DB-15 to Mini Din, 4.6M Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0063c.htm [25.04.
PAGE 198
Sun4/II: Parts - Input Device - Type-4 Optical Mouse Type-4 Optical Mouse PART # DESCRIPTION 370-1161 M4 200 CPI Mouse and Pad, Mini-Din (unreleased, obs) 365-1059 M4 200 CPI Mouse and Pad, Mini-Din 370-1170 M4 200 CPI Mouse, Mini-Din 370-1215 M4 Mouse Pad, 200 CPI, 0.032", 228.6 x 196.9 mm (obs) 370-1368 M4 Mouse Pad, 200 CPI, 0.032", 177.8 x 196.9 mm Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0063d.htm [25.04.
PAGE 199
Sun4/II: Parts - Input Device - Type-5 Optical Mouse Type-5 Optical Mouse PART # DESCRIPTION f370-1398 Type-5 Mouse and Pad, Mini-Din Type-5 Mouse, 300 CPI, Mini-Din 370-1398 Type-5 Mouse Pad, 300 CPI, 196.6 x 178.0 mm 370-1399 370-1664 Type-5 Mouse without Sun Logo, 300 CPI, Mini-Din 370-1663 Type-5 Mouse Pad without Sun Logo, 300 CPI Notes 1. The Type-5 Mouse replaced the Type-4 Mouse in October 1993. 2. The Compact 1 Mouse replaced the Type-5 Mouse in August 1995.
PAGE 200
Sun4/II: Parts - Board - Contents Board IDPROM Boot PROM Sun-4 Architecture CPU Sun-4 Architecture Memory Sun-4 SIMMs / Sun-4c SIMMs Video P4 Bus VMEbus Cables SCSI Multibus / VMEbus Single-Ended 8-Bit SCSI Cables IPI ISP-80 Communication Ethernet Accessories VMEbus Backplane Miscellaneous Boards Board Hardware Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004d4.htm [25.04.
PAGE 201
Sun4/II: Parts - Board - IDPROM IDPROM The IDPROM address space provides system information including Machine Type, Serial Number, Ethernet Address, and Manufacturing Date. This information may be stored in an IDPROM, NVRAM, or EEPROM. The 32 Bytes of IDPROM content are shown below.
PAGE 202
Sun4/II: Parts - Board - IDPROM NVRAM Component Types NVRAM Battery Types ARCH SYSTEM HOSTID COMPONENT TYPE PART # SOCKET http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00608.htm (2 von 3) [25.04.
PAGE 203
Sun4/II: Parts - Board - IDPROM Sun-4 Sun-4c Sun-4m Sun-4d Sun-4u 4/260/280 4/110/150 4/3xx 4/3xx 4/470/490 4/470/490 SS1 SS IPC SS1+ SS SLC SS ELC SS IPX SS2 4E SPARCclassic X SPARCclassic SS LX SPARC Xterm 1 SS4 SS5 SS10 SS10SX SS20 SS600MP SS Voyager JavaStation SS1000/1000E SS1000/1000E SS1000/1000E SC2000/2000E SC2000/2000E SC2000/2000E A11 A12 A14 2100xxxx 22xxxxxx 23xxxxxx None 24xxxxxx None 51xxxxxx 52xxxxxx 53xxxxxx 54xxxxxx 56xxxxxx 57xxxxxx 55xxxxxx 61xxxxxx 80xxxxxx 80xxxxxx 80xxxxxx 80xx
PAGE 204
Sun4/II: Parts - Board - Boot PROM Sun-4 Boot PROM Sun-4 Architecture Sun-4100 / Sun-4200 / Sun-4300 U601 520-1651-03 520-1651-04 520-1651-06 520-1651-07 520-1651-08 520-1651-09 525-1651-10 525-1651-11 525-1651-12 595-1964-xx Sun-4/110/150 U602 U603 520-1652-03 520-1653-03 520-1652-04 520-1653-04 520-1652-06 520-1653-06 520-1652-07 520-1653-07 520-1652-08 520-1653-08 520-1652-09 520-1653-09 525-1652-10 525-1653-10 525-1652-11 525-1653-11 525-1652-12 525-1653-12 Boot PROM Kit U604 Revision 520-1654-03 1.
PAGE 205
Sun4/II: Parts - Board - Boot PROM Sun-4 U3504 525-1103-01 525-1103-02 525-1103-03 525-1103-04 525-1103-06 595-2123-xx Sun-4/470/490 U3503 U3502 525-1104-01 525-1105-01 525-1104-02 525-1105-02 525-1104-03 525-1105-03 525-1104-04 525-1105-04 525-1104-06 525-1105-06 Sun 4400 Boot PROM Kit U3501 Revision 525-1106-01 0.1.d 525-1106-02 0.2.c 525-1106-03 3.0 525-1106-04 4.0 525-1106-06 4.1.1 Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.
PAGE 206
Sun4/II: Parts - Board - CPU Sun-4 CPU Sun-4 Architecture Sun 4100 / Sun 4200 / Sun 4300 / Sun 4400 PART # 501-1199 501-1512 501-1656 501-1237 501-1513 501-1657 501-1462 501-1514 501-1658 501-1463 501-1515 501-1659 501-1464 501-1516 501-1660 501-1465 501-1517 501-1661 DESCRIPTION 8MB Sun 4100 CPU (270-1199-03) without FPC 8MB Sun 4100 CPU (270-1199-04) without FPC 8MB Sun 4100 CPU (270-1199-07) without FPC 8MB Sun 4100 CPU (270-1199-03) with FPC4 or FPC6 8MB Sun 4100 CPU (270-1199-04) with FPC4 or FPC6 8
PAGE 207
Sun4/II: Parts - Board - CPU Sun-4 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0060c.htm (2 von 2) [25.04.
PAGE 208
Sun4/II: Parts - Board - Memory Memory Sun-4 SIMMs PART # 501-1314 501-1544 501-1408 501-1466 501-1544 501-1565 501-1682 501-1739 DESCRIPTION 256KB, 256KB x 9-Bit SIMM, Sun 4100 1MB, 1Mbit x 9-Bit SIMM, Sun 4300 1MB, 1Mbit x 9-Bit SIMM, Sun-3/80 and Sun-4/60/65/300 1MB, 1Mbit x 9-Bit SIMM, Sun 4100 1MB, 1Mbit x 9-Bit SIMM, Sun 4300 1MB, 1Mbit x 9-Bit SIMM, Sun 4300 4MB, 1Mbit x 9-Bit SIMM, Sun 4300 4MB, 1Mbit x 9-Bit SIMM, Sun-4/40/60/65/75/300 Sun 4300 / Sun 4400 / Sun-4/E PART # 501-1436 501-1723 501-1
PAGE 209
Sun4/II: Parts - Board - Video - P4 Bus Video P4 Bus PART # 501-1247 501-1248 501-1371 501-1402 501-1518 DESCRIPTION MG3 ECL Frame Buffer, DB-9 CG4 Color Frame Buffer, BNC CG8 Color Frame Buffer, BNC MG4 ECL/Analog Frame Buffer, DB-9/DB13W3 CG8 Color Frame Buffer, DB13W3 GX Graphics Option 501-1374 CG6 Color Frame Buffer, DB13W3 501-1505 CG6 Color Frame Buffer, DB13W3 501-1532 CG6 Color Frame Buffer, DB13W3 Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.
PAGE 210
Sun4/II: Parts - Board - Video - VMEbus Video VMEbus PART # 501-1014 540-1126 599-1165 501-1089 501-1116 501-1319 501-1267 501-1055 501-1139 501-1268 501-1058 501-8020 501-8029 501-1383 501-1447 DESCRIPTION CG2 Color Frame Buffer CG2 Color Frame Buffer (obsolete) CG2 Color Frame Buffer (obsolete) CG3 Double Buffered Color Frame Buffer CG3 Color Frame Buffer CG3 Double Buffered Color Frame Buffer, 1024x1024 CG5 Color Frame Buffer GP Graphics Processor GP+ Graphics Processor Plus GP2 Graphics Processor Two
PAGE 211
Sun4/II: Parts - Board - Video - Cables Video Cables PART # 530-0492 530-1138 530-1307 530-1362 530-1415 530-1440 530-1446 530-1509 530-1839 530-1840 530-1870 530-1898 530-2020 DESCRIPTION Color Cable, 4.6M, 1xBNC to 1xBNC Color Cable, 4.6M, 4xBNC to 4xBNC Color Cable, 4.6M, 4xBNC to 4xBNC Color Cable, 1.2M, 4xBNC to 4xBNC Color Cable, 50 cm, 4xBNC to 4xBNC Color Cable, 1.2M, DB13W3 to DB13W3 Color Adapter Cable, 4xBNC to DB13W3 Color Cable, 4.6M, DB13W3 to DB13W3 Color Cable, 1.
PAGE 212
Sun4/II: Parts - Board - SCSI - Multibus SCSI Multibus / VMEbus PART # DESCRIPTION 501-1006 Sun-2 Multibus SCSI Host Adapter 501-1045 501-1120 501-1236 501-8027 Sun-2 VMEbus SCSI Host Adapter Sun-3 VMEbus SCSI Host Adapter (obsolete) Sun-3 VMEbus SCSI Host Adapter Sun-3/E VMEbus SCSI Host Adapter 501-1147 501-1045 501-1079 501-1149 501-1045 270-1059 501-1138 501-1045 270-1138 501-1167 501-1045 270-1059 501-1170 501-1236 270-1059 501-1217 501-1236 270-1138 Sun-2/50 SCSI Host Adapter Assembly, External SC
PAGE 213
Sun4/II: Parts - Board - SCSI - Single SCSI Cables SCSI Single-Ended 8-Bit SCSI Cables PART # 530-1185 530-1186 530-1249 530-1250 530-1334 530-1365 DESCRIPTION External Cable, DD-50SA to DD-50SA, Ribbon, 1.0M (obs) External Cable, DD-50SA to DD-50SA, Ribbon, 5.0M (obs) External Cable, DD-50SA to DD-50SA, 1.0M External Cable, DD-50SA to DD-50SA, 3.0M External Cable, DD-50SA to DD-50SA, 2.
PAGE 214
Sun4/II: Parts - Board - IPI - ISP-80 IPI ISP-80 PART # DESCRIPTION 501-1539 ISP-80 IPI-2 DIsk Controller 501-1855 ISP-80 IPI-2 DIsk Controller 530-1487 IPI Command Cable, 8.0M (obsolete) 530-1488 IPI Command Cable, 1.0M 530-1489 IPI "W" Command Cable (not released) 530-1518 IPI Command Cable, 2.0M (obsolete) 530-1536 IPI Command Cable, 0.45M 530-1788 IPI Command Cable, 2.0M 530-1789 IPI Command Cable, 8.
PAGE 215
Sun4/II: Parts - Board - Communication - Ethernet Accessories Communication Ethernet Accessories PART # 130-1240 130-1241 130-1242 130-1243 130-1244 130-1245 370-0288 370-0331 370-0363 370-0364 370-0368 370-0549 370-1071 370-1071 370-1072 370-1073 370-1074 370-1075 530-1241 530-1253 530-1254 530-1280 530-1519 530-1696 xxx-xxxx DESCRIPTION BNC Female to N-series Male Option TA-M BNC Male Terminator Option TT-M BNC "T",F,M,F Option TTC BNC Barrel, Double Female Option TBC BNC Terminator, Female Option TT-F
PAGE 216
Sun4/II: Parts - Board - Communication - Ethernet Accessories 370-1071 370-1072 530-1241 530-1254 370-1071 370-1072 530-1241 530-1253 530-1871 530-1871 530-2093 530-2149 530-2150 530-2027 530-2027 530-2105 530-2105 Option INLINE 3Com 3C106 Transceiver Vampire Tap Block, AMP 228752-1 15-meter Transceiver Drop Cable 15-meter Ethernet Coax Cable Option ECX Option Thin 3Com 3C106 Transceiver Vampire Tap Block, AMP 228752-1 15-meter Transceiver Drop Cable 15-meter Thin Ethernet Cable Option TS-15M Twisted Pair
PAGE 217
Sun4/II: Parts - Board - Communication - VMEbus Communication VMEbus Ethernet / FDDI / Network CoProcessor PART # 501-8027 501-1153 501-1004 530-1173 501-1584 501-8027 530-1607 501-1276 537-1000 370-1396 370-1421 501-1920 DESCRIPTION Sun-3/E SCSI/Ethernet Controller Sun-2 Ethernet Controller Assembly Sun-2 Multibus Ethernet Controller Ethernet Cable, Ethernet Controller to Backpanel Sun-3/E Ethernet Controller Assembly Sun-3/E Ethernet Controller Ethernet Cable, Ethernet Controller to Backpanel SunLight
PAGE 218
Sun4/II: Parts - Board - Communication - VMEbus 501-1203 16-Channel Asychronous Line Multiplexer-2 (ALM-2) 530-1312 Internal Parallel Port Cable, 14.5 cm 530-1315 Internal Cable, 50-Pin, 11.5 cm 340-1569 Rack Mounting Bracket 340-1587 Wall Mounting Bracket 340-1914 Rack Mounting Bracket, Short, 56" Rack 340-1915 Rack Mounting Bracket, Long, 56" Rack 530-1334 Cable, ALM-2 to DCA, 2.
PAGE 219
Sun4/II: Parts - Board - Backplane Backplanes and I/O Boards PART # 501-1092 501-1117 501-1127 501-1128 501-1354 501-1439 501-1498 501-1597 501-1598 501-1832 DESCRIPTION 12-Slot VMEbus Backplane, (obsolete) 12-Slot VMEbus Backplane, Pressfit 3-Slot VMEbus Backplane, Pressfit 6-Slot VMEbus Backplane, Pressfit 5-Slot VMEbus Backplane, Pressfit 12-Slot Backplane, 9 VMEbus Slots, Pressfit (obsolete) 16-Slot Backplane, 13 VMEbus Slots, Pressfit (obsolete) 16-Slot Backplane, 13 VMEbus Slots, Pressfit, Fused 12-
PAGE 220
Sun4/II: Parts - Board - Miscellaneous - Boards Miscellaneous Boards PART # 501-1154 501-1191 501-1220 501-1269 501-1384 501-1387 501-1454 501-1666 540-1108 540-1250 DESCRIPTION VMEbus to Multibus Adapter Assembly, Blank Backpanel VME 3x2 Adapter Assembly, without P2 A&C, Option 160B VME 3x2 Adapter Assembly, without P2 A&C VME 3x2 Adapter Assembly, with P2 A&C, Option 160A Sun 4100 FPU2 Sun 4200 FPU2 Sun-4/60 FPU VME 3x2 Adapter Assembly, with P2 A&C VME 3x2 Adapter Assembly (obsolete) VMEbus to Multibus
PAGE 221
Sun4/II: Parts - Board - Miscellaneous - Board Hardware Miscellaneous Board Hardware PART # 130-0272 130-2190 240-1287 240-1288 340-1407 340-1818 540-1433 DESCRIPTION 2-Pin Shunt, 0.10" Pin Spacing, 0.025" Pin Diameter 2-Pin Shunt, 2.0 mm Pin Spacing, 0.50 mm Pin Diameter Hex Screw, M2.5 0.45 x 16 mm Hex Screw, M2.5 0.
PAGE 222
Sun4/II: Parts - Miscellaneous Options - Contents Miscellaneous Options Option 955 56-inch Expansion Cabinet Option 960 76-inch Expansion Cabinet Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004d1.htm [25.04.
PAGE 223
Sun4/II: Parts - Miscellaneous Options - 56-inch Expansion Cabinet 955 56-inch Expansion Cabinet CODE PART # DESCRIPTION 1 340-1884 Anti-Tilt Panel 2 540-1857 Vented Panel Assembly http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0064c.htm (1 von 2) [25.04.
PAGE 224
Sun4/II: Parts - Miscellaneous Options - 56-inch Expansion Cabinet 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 21 21 22 23 24 NS NS NS NS 540-1947 540-2252 540-1859 240-1630 340-1840 540-2393 340-1913 340-1885 240-1372 540-1718 340-1848 370-1983 240-1953 340-1886 240-1717 240-1373 230-1418 300-1263 300-1264 540-1929 540-1930 240-1655 340-1845 340-2047 230-1166 230-1170 340-2138 530-1303 800-6371 1/2" Tape Panel Assembly with Cutout Front Panel with 4 Tape Drive Cutouts Cap Panel Assembly #6-32 Ball
PAGE 225
Sun4/II: Parts - Miscellaneous Options - 76-inch Expansion Cabinet 960 76-inch Expansion Cabinet PART # 180-1149 300-1011 300-1263 300-1264 340-0530 340-1283 340-1284 340-1285 340-1286 340-1287 340-1441 340-1442 340-1485 340-1487 340-1489 340-1490 340-1522 340-1554 340-1595 340-1597 340-1662 340-1700 340-1701 340-1715 370-1027 370-1045 370-1053 370-1105 370-1126 370-1155 370-1156 530-1298 530-1303 530-1328 530-1343 DESCRIPTION 32Amp IEC-309 AC Receptacle (240V) AC Power Sequencer (115V) AC Power Sequencer
PAGE 226
Sun4/II: Parts - Miscellaneous Options - 76-inch Expansion Cabinet 530-1344 530-1346 530-1347 530-1348 530-1349 530-1350 530-1351 540-1285 540-1428 340-1491 370-0550 540-1503 340-1491 370-1124 540-1568 340-1491 370-1124 540-1585 340-1583 340-1584 560-1113 AC Power Cord, Fan Assembly (240V) AC Power Cord, Fujitsu M2444AC Tape Drive (240V) AC Power Cord, Fujitsu M2361A Disk Drive (240V) AC Power Cord, Fujitsu M2444AC Tape Drive (230V) AC Power Cord, Fujitsu M2361A Disk Drive (230V) AC Power Cord, CDC 92181
PAGE 227
Sun4/II: Parts - Removable Media Options - Contents Removable Media Options Options 558 / 559 Desktop SunCD Pack Option 660 150MB Tape Desktop Backup Pack Options 680 / 682 / 683 / 684 / 685 Front-Load 1/2" Tape Drive Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004ce.htm [25.04.
PAGE 228
Sun4/II: Parts - Removable Media Options - Desktop SunCD Pack 558 559 SunCD CD-ROM SunCD CD-ROM Desktop SunCD Pack CODE 1 2 3 3 4 NS NS PART # DESCRIPTION 540-1778 Cover Assembly, Tape and CD-ROM 540-1978 Fan/SCSI Connector/Address Select FRU Assembly 150-1557 Address Select Switch (obsolete) 150-2049 Address Select Switch 540-1802 Fan Assembly 150-1174 2A Subminiature Fuse 340-2839 Fan EMI Gasket http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00680.htm (1 von 2) [25.04.
PAGE 229
Sun4/II: Parts - Removable Media Options - Desktop SunCD Pack 5 6 7 7 7 8 9 10 11 11 NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS 540-1773 330-1214 300-1037 300-1090 300-1105 540-1931 370-1312 340-1967 530-1454 530-1825 240-1141 150-1346 150-1785 530-1434 530-1435 530-1508 530-1593 530-1792 530-1793 530-1829 530-1836 530-1852 555-1154 370-1316 800-4895 Base Assembly Rubber Foot 35 Watt Power Supply (obsolete) 1 35 Watt Power Supply (obsolete) 44 Watt Power Supply SunCD CD-ROM Assembly Sony CDU-8012 CD-RO
PAGE 230
Sun4/II: Parts - Removable Media Options - 150MB Tape Desktop Backup Pack 660 150MB Tape Desktop Backup Pack CODE 1 2 3 4 NS PART # DESCRIPTION 540-1778 Tape Drive Cover Assembly 540-1776 Fan/SCSI Connector/Address Select Assy (obs) 150-1338 Address Select Switch (obsolete) 540-1802 Fan Assembly 150-1174 2A Subminiature Fuse http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00681.htm (1 von 2) [25.04.
PAGE 231
Sun4/II: Parts - Removable Media Options - 150MB Tape Desktop Backup Pack 2 3 3 4 NS NS 5 6 7 7 7 8 9 10 10 NS NS NS NS NS NS NS NS NS 540-1978 150-1557 150-2049 540-1802 150-1174 340-2839 540-1773 330-1214 300-1037 300-1090 300-1105 370-1218 340-1967 530-1454 530-1825 240-1141 150-1346 150-1785 530-1434 530-1508 530-1793 530-1836 530-1852 800-4895 Fan/SCSI Connector/Address Select Assembly Address Select Switch (obsolete) Address Select Switch Fan Assembly 2A Subminiature Fuse Fan EMI Gasket Base Assemb
PAGE 232
Sun4/II: Parts - Removable Media Options - Front-Load 1/2" Tape Drive 680 682 TableTop 56" Rack 683 684 685 56" Exp Rack 56" Exp Rack SC2000 1st Tape 2nd Tape 56" Exp Rack CODE SUN PART# 1 811-1236 1 811-1236 2 811-1210 3 811-1227 4 811-1228 5 811-1242 6 811-1245 7 811-1241 8 811-1229 9 140-1011 9 140-1002 9 140-1039 HP PART# 88780-67707 88780-68207 07980-44111 07980-61616 07980-65000 07980-69025 07980-60043 88780-69015 07980-67919 None None None DESCRIPTION Front Bezel Assembly 1 Front Bezel Assemb
PAGE 233
Sun4/II: Parts - Removable Media Options - Front-Load 1/2" Tape Drive 10 11 12 13 13 14 15 16 17 18 19 20 21 21 22 23 24 811-1235 811-1231 811-1215 811-1218 811-1218 811-1214 811-1216 811-1209 811-1233 811-1219 370-1276 370-1277 370-1279 370-1279 811-1232 811-1211 811-1212 3110-0178 1390-0776 07980-60041 07980-60052 07980-60152 07980-60040 07980-60045 07980-21701 1460-2180 07980-60053 07980-66531 07980-66503 07980-66514 07980-66534 1420-0314 07980-60000 07980-60008 Cover Hinge Cover Latch Speed Sensor A
PAGE 234
Sun4/II: Parts - Removable Media Options - Front-Load 1/2" Tape Drive COD E SUN PART# 25 811-1230 26 811-1217 27 811-1226 28 811-1238 29 811-1237 30 811-1213 31 811-1292 NS 811-1220 NS 811-1221 NS 811-1222 NS 811-1223 NS 811-1224 NS 811-1225 NS 811-1234 NS 811-1240 NS 811-1243 HP PART# 07980-86500 07980-60050 07980-60144 07980-60042 07980-60051 07980-60009 9100-4637 07980-60062 07980-60064 07980-60067 07980-60070 07980-60071 07980-60072 3101-2923 07980-60065 88780-60290 DESCRIPTION Blower Motor Takeup/Su
PAGE 235
Sun4/II: Parts - Removable Media Options - Front-Load 1/2" Tape Drive NS NS NS 811-1243 811-1243 811-1244 88780-60082 Firmware Kit (not qualified) 88780-6018 2 Firmware Kit 1 07980-60048 NRZI Speed Sensor 1. Firmware Kit 88780-60182 includes Drive Controller firmware level 6.76, Buffer firmware level 6.77, and SCSI firmware level 6.62.
PAGE 236
Sun4/II: Parts - Removable Media Options - Front-Load 1/2" Tape Drive 530-1501 Data Cable, DD-50SA to Centronics, 2.0M 540-1823 Rackmount Tape Drive without Fuse and Labels Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00682.htm (5 von 5) [25.04.
PAGE 237
Sun4/II: Parts - Disk Options - Contents Disk Options Options 526 / 527 / 530 / 539 327MB Disk External Storage Module Options 561 / 563 / 565 / 566 669MB Disk External Storage Module Options 706 / 707 / 709 / 710 1.2GB IPI-2 Disk Subsystem Options 716 / 717 / 719 / 720 911MB IPI-2 Disk Subsystem Options 726 / 727 / 728 1.3GB IPI-2 Disk Subsystem Options 741A / 742A / 743A / 744A / 745A 1.
PAGE 238
Sun4/II: Parts - Disk Options - External Storage and External Expansion Modules 526 527 530 327MB Disk 327MB Disk Expansion Two 327MB Disks 539 327MB Disk 150MB Tape External Storage and External Expansion Modules PART # 150-1556 300-1031 330-1146 330-1158 350-1006 350-1010 350-1011 350-1013 350-1117 370-1203 370-1246 530-1249 530-1250 530-1334 530-1365 530-1381 530-1409 530-1435 530-1593 530-1792 530-1829 530-1461 530-1618 530-1659 555-1005 330-1146 330-1158 370-1153 570-1042 814-5036 DESCRIPTION SC
PAGE 239
Sun4/II: Parts - Disk Options - External Storage and External Expansion Modules Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00622.htm (2 von 2) [25.04.
PAGE 240
Sun4/II: Parts - Disk Options - External Storage and External Expansion Module 561 563 669MB Disk Two 669MB Disks 565 566 669MB Disks 669MB Disk 150MB Tape 2.
PAGE 241
Sun4/II: Parts - Disk Options - External Storage and External Expansion Module 530-1659 Address Select Switch Cable, 2.54 mm Pin Spacing 570-1042 Full-Height Peripheral Front Filler Panel 814-5036 Replacing Components of Sun ESM and EEM Storage Units 1. The Maxtor drive does not fit into the lower drive position of External Storage Modules manufactured prior to October 1990. Remove the vertical stop block with10-Inch End Cutter, 250-1074-01.
PAGE 242
Sun4/II: Parts - Disk Options - 1.2GB IPI-2 Disk Subsystem 706 707 709 710 1.2GB Disk 2.1.2GB Disks 4 1.2GB Disks 8 1.2GB Disks 1.2GB IPI-2 Disk Subsystem CODE PART # 540-1770 1 300-1041 2 370-1263 3 240-1603 4 240-1185 5 370-1262 6 240-1035 7 240-1602 DESCRIPTION IPI Drive, Power Supply, and Tray Assembly 205W Power Supply DC Harness Cable Clamp #6-32 x 1/4" Screw Operator Panel Harness Lock Washer, #6 Cable Clamp http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00624.
PAGE 243
Sun4/II: Parts - Disk Options - 1.2GB IPI-2 Disk Subsystem 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS 370-1350 370-1187 240-1185 250-1013 240-1186 240-1595 180-1185 250-1023 340-1854 240-1185 250-1016 330-1224 330-1226 370-1221 330-1225 240-1601 240-1596 180-1183 180-1184 340-1853 340-1855 340-1856 340-1891 340-2296 370-1220 530-1351 530-1343 530-1487 530-1488 530-1518 530-1536 530-1788 530-1789 None 370-1330 Air Baffle 1.
PAGE 244
Sun4/II: Parts - Disk Options - 911MB IPI-2 Disk Subsystem 716 717 719 720 911MB Disk 2 911MB Disks 4 911MB Disks 8 911MB Disks 911MB IPI-2 Disk Subsystem CODE PART # 540-2005 1 300-1074 2 370-1263 3 240-1603 4 240-1185 5 370-1262 6 240-1035 7 240-1602 DESCRIPTION IPI Drive, Power Supply, and Tray Assembly 215 Watt Power Supply DC Harness Cable Clamp #6-32 x 1/4" Screw Operator Panel Harness #6 Lock Washer Cable Clamp http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00625.
PAGE 245
Sun4/II: Parts - Disk Options - 911MB IPI-2 Disk Subsystem 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS 370-1350 370-1351 240-1185 250-1013 240-1186 240-1595 180-1185 250-1023 340-1854 240-1185 250-1016 330-1224 330-1226 370-1355 330-1225 240-1601 240-1596 180-1183 180-1184 340-1853 340-1855 340-1856 340-1891 340-2296 370-1220 530-1351 530-1343 530-1487 530-1488 530-1518 530-1536 530-1788 530-1789 None 370-1330 Air Baffle 911MB Disk, Seagate 97229
PAGE 246
Sun4/II: Parts - Disk Options - 1.3GB IPI-2 Disk Subsystem 726 727 728 2 1.3GB Disks 4 1.3GB Disks 1.3GB Disk 1 Tray 1 Tray 1.3GB IPI-2 Disk Subsystem CODE 1 2 3 4 5 6 7 8 9 10 PART # 340-2461 None 240-1372 230-1170 150-1557 230-1256 340-2466 240-1373 501-1827 530-1768 DESCRIPTION Chassis Enclosure #8-32 x 1/4" Pan Head Screw, Slide Rail to Chassis M4 0.
PAGE 247
Sun4/II: Parts - Disk Options - 1.
PAGE 248
Sun4/II: Parts - Disk Options - Sun Expansion Pedestal 741A 742A 743A 745A 1.2GB Disk 2 1.2GB Disks 3 1.2GB Disks 4 1.2GB Disks 744A 1.2 GB Disk Standalone Sun Expansion Pedestal CODE NS NS 1 NS NS NS NS NS NS NS NS NS PART # 340-2188 340-2208 540-1926 370-1314 340-2300 180-1486 240-1207 250-1070 340-1898 330-1192 540-1749 540-1846 DESCRIPTION Rear Panel without Cables Filler Panel IPI8-1000 3MB/Sec Disk Drive FRU Assembly 1.
PAGE 249
Sun4/II: Parts - Disk Options - Sun Expansion Pedestal NS NS NS NS NS NS NS NS NS 2 NS NS 3 NS NS NS 4 5 6 7 8 8 NS NS NS NS NS 540-1847 540-1939 530-1487 530-1488 530-1518 530-1536 530-1788 530-1789 370-1220 540-1765 340-2050 501-1531 540-1748 330-1212 330-1213 340-1936 530-1495 340-2129 240-1372 530-1544 300-1052 300-1075 530-1619 340-2262 230-0203 230-1188 800-3257 Rear Bezel Assembly Front Panel and Bumper Assembly IPI Drive I/O Cable, 8.0M (obsolete) IPI Drive I/O Cable, 1.0M IPI Drive I/O Cable, 2.
PAGE 250
Sun4/II: Parts - Disk Options - Sun Expansion Pedestal 741L 742L 743L 744L 745L 911MB Disk 2 911MB Disks 3 911MB Disks 4 911MB Disks 911MB Disk Standalone Sun Expansion Pedestal CODE NS NS 1 NS NS NS NS NS NS NS NS NS PART # 340-2188 340-2208 540-2008 370-1352 340-2300 180-1486 240-1207 250-1070 340-1898 330-1192 540-1749 540-1846 DESCRIPTION Rear Panel without Cables Filler Panel IPI8-1000/2HP 6MB/Sec Disk Drive FRU Assembly 911MB Disk Drive, Seagate 97209-11G, PA8Y2 1 Disk Mounting Cradle Front
PAGE 251
Sun4/II: Parts - Disk Options - Sun Expansion Pedestal NS NS NS NS NS NS NS NS NS 2 NS NS 3 NS NS NS 4 5 6 7 8 NS NS NS NS NS 540-1847 540-1939 530-1487 530-1488 530-1518 530-1536 530-1788 530-1789 370-1220 540-1765 340-2050 501-1531 540-1748 330-1212 330-1213 340-1936 530-1495 340-2129 240-1372 530-1544 300-1075 530-1619 340-2262 230-0203 230-1188 800-3257 Rear Bezel Assembly Front Panel and Bumper Assembly IPI Drive I/O Cable, 8.0M IPI Drive I/O Cable, 1.0M IPI Drive I/O Cable, 2.
PAGE 252
Sun4/II: Parts - Disk Options - SCSI Expansion Pedestal 750 754 756 2 1.3GB Disks 4 1.3GB Disks 2 1.3GB Disks 1 Tray 8 mm Tape Expansion Tray SCSI Expansion Pedestal CODE 1 2 2 3 4 5 PART # 540-1846 300-1091 300-1106 340-1898 340-2534 340-2292 DESCRIPTION Side Cover 800 Watt Power Supply 800 Watt Power Supply Top Cover Front EMI Cover, without Switch Assembly Blank EMI Cover Filler Panel http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00629.htm (1 von 2) [25.04.
PAGE 253
Sun4/II: Parts - Disk Options - SCSI Expansion Pedestal 6 7 7 8 NS NS 9 NS NS NS NS 10 11 11 12 NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS 330-1192 330-1210 330-1284 540-1939 240-0558 240-0557 540-1765 501-1531 540-2136 330-1373 340-2491 340-2444 370-1377 370-1377 340-2129 150-1785 340-2535 340-2543 370-1297 370-1347 530-1619 530-1675 530-1676 530-1793 530-1811 530-1824 530-1836 530-1841 530-1842 530-1852 540-1749 540-1847 540-2157 800-6402 800-7286 Blank Bezel Insert Front Bezel Half-Height I
PAGE 254
Sun4/II: Parts - System - Contents System Sun-4 Architecture Sun-4/110/310 Sun-4/150/350 Sun-4/260/360 Sun-4/280/380 Sun-4/330 Sun-4/370/470 Sun-4/390/490 Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004c8.htm [25.04.
PAGE 255
Sun4/II: Parts - System - Sun-4/110/310 Sun-4/110/310 3-Slot VMEbus Logic Enclosure PART # 140-1019 140-1030 150-1042 150-1051 180-1010 180-1097 180-1117 180-1125 240-1368 260-4443 300-1022 300-1022 300-1093 330-1067 330-1069 330-1071 330-1089 330-1144 340-1545 370-1106 370-1178 501-1127 540-1384 540-1418 540-1419 501-1193 540-1455 540-1535 540-1541 540-1542 800-2126 DESCRIPTION Fuse, 15A (115V) Fuse, 6.
PAGE 256
Sun4/II: Parts - System - Sun-4/150/350 Sun-4/150/350 6-Slot VMEbus Logic Enclosure PART # 140-1019 140-1030 150-1042 150-1051 150-1217 180-1010 180-1097 180-1117 180-1125 240-1368 330-1068 330-1070 330-1071 330-1089 330-1143 340-1547 370-1106 370-1178 501-1128 530-1352 530-1353 540-1381 540-1409 501-1233 540-1471 540-1410 300-1020 340-1454 540-1475 800-1944 DESCRIPTION Fuse, 15A (115V) Fuse, 6.
PAGE 257
Sun4/II: Parts - System - Sun-4/260/360 Sun-4/260/360 12-Slot VMEbus Logic Enclosure PART # 140-1019 140-1030 150-1018 150-1216 150-1041 150-1042 150-1051 150-1129 180-1097 180-1125 240-1048 260-4442 330-1066 330-1076 340-1138 340-1261 340-1262 370-1086 501-1092 501-1117 530-1134 530-1135 530-1230 530-1231 530-1207 800-1525 DESCRIPTION Fuse, 15A (115V) Fuse, 6.
PAGE 258
Sun4/II: Parts - System - Sun-4/260/360 540-1555 540-1510 530-1357 540-1581 540-1510 530-1357 540-1584 540-1572 530-1357 540-1596 540-1572 530-1357 6-Fan Tray Assembly (obsolete) DC Fan Assembly, 71 CFM DC Harness, Fan Tray 6-Fan Tray Assembly, Low Profile, No Fingerguards (obs) DC Fan Assembly, 71 CFM DC Harness, Fan Tray 6-Fan Tray Assembly, Low Profile, Individual Fingerguards DC Fan Assembly, 71 CFM, Low Profile DC Harness, Fan Tray 6-Fan Tray Assembly, Low Profile, Full Screen DC Fan Assembly, 71 CFM
PAGE 259
Sun4/II: Parts - System - Sun-4/260/360 370-1010 370-1034 370-1034 530-1134 530-1135 530-1142 530-1145 530-1157 370-0552 370-1236 370-0551 370-0551 370-1133 530-1134 530-1135 530-1142 530-1145 530-1157 Adaptec ACB-4000 SCSI Disk Controller 71MB Disk Drive, Micropolis 1325 71MB Disk Drive, Fujitsu M2243AS SCSI Bus Cable, Backplane to SCSI Tray DC Harness, Power Supply DC Harness to SCSI Tray Disk Data Cable, 39 cm, LUN 0 Disk Data Cable, 62 cm, LUN 1 Disk Command Cable, Dual Disk Emulex MD21 SCSI Disk Cont
PAGE 260
Sun4/II: Parts - System - Sun-4/280/380 Sun-4/280/380 12-Slot VMEbus Logic Enclosure PART # 140-1019 140-1026 140-1030 150-1018 150-1216 150-1041 150-1042 150-1051 150-1129 180-1097 260-4441 330-1076 340-1283 340-1583 340-1584 340-1685 340-1686 370-1086 501-1092 501-1117 530-1230 530-1257 530-1258 530-1260 530-1343 530-1351 540-1366 530-1259 530-1321 540-1129 540-1509 540-1508 540-1585 DESCRIPTION Fuse, 15A (115V) Fuse, 6A (230V) Fuse, 6.
PAGE 261
Sun4/II: Parts - System - Sun-4/280/380 Power Supplies PART # 300-1024 530-1206 530-1340 530-1222 530-1320 300-1043 530-1578 530-1580 DESCRIPTION 850 Watt Power Supply, Fuji Electrochemical DC Harness, +5Vdc (obsolete) DC Harness, +5Vdc DC Harness, +5Vdc, -5Vdc, +12Vdc, -12Vdc (obsolete) DC Harness, +5Vdc, -5Vdc, +12Vdc, -12Vdc 925 Watt Power Supply, Fuji Electrochemical DC Harness, +5Vdc DC Harness, +5Vdc, -5Vdc, +12Vdc, -12Vdc 1/4" Tape Drive Option PART # 230-1007 370-1061 370-1235 370-1076 370-1103 3
PAGE 262
Sun4/II: Parts - System - Sun-4/280/380 340-1287 340-1441 340-1442 340-1485 340-1487 340-1489 340-1490 340-1522 340-1554 340-1595 340-1597 340-1662 340-1700 340-1701 340-1715 370-1027 370-1045 370-1053 370-1105 370-1126 370-1155 370-1156 530-1298 530-1303 530-1328 530-1343 530-1344 530-1346 530-1347 530-1348 530-1349 530-1350 530-1351 540-1285 540-1428 340-1491 370-0550 540-1503 340-1491 370-1124 540-1568 Panel, 24.5" x 19" Keyswitch Panel, 1.5" x 19" Tape Drive Filler Panel, 1.
PAGE 263
Sun4/II: Parts - System - Sun-4/280/380 340-1491 370-1124 540-1585 340-1583 340-1584 560-1113 Fan Bracket AC Fan (240V) 19" Logic Enclosure Support Rail Assembly 19" Logic Enclosure Support Rail Bracket 19" Logic Enclosure Support Rail 19" Logic Enclosure Mounting Hardware Kit Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068d.htm (4 von 4) [25.04.
PAGE 264
Sun4/II: Parts - System - Sun-4/330 Sun-4/330 5-Slot VMEbus Logic Enclosure CODE NS NS 1 NS 2 PART # 260-3617 260-3818 330-1178 330-1180 540-1760 NS NS 3 3 4 5 530-1465 530-1468 540-2029 540-1788 540-1811 530-1470 DESCRIPTION SPARCstation 330 Logo SPARCserver 330 Logo Rear Cover Cable Retainers Fan and Bracket Assembly DC Harness, Power Supply to Peripherals & Fans 1 Fan Harness 1 Fan Assembly, Variable Speed, 105 CFM Fan Assembly, 100 CFM (obsolete) AC Receptacle AC Input Harness http://lios.apana.
PAGE 265
Sun4/II: Parts - System - Sun-4/330 6 NS NS NS 7 8 9 NS 10 NS 10 NS 11 NS 11 NS 12 13 14 NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS 340-1772 501-1432 501-1416 120-1608 540-1789 530-1469 540-1787 340-2500 540-1758 340-1783 540-2133 340-2497 540-1757 340-1782 540-2132 340-2498 150-1129 340-1792 300-1034 150-1323 150-1346 150-1785 240-1605 330-1180 340-1676 340-1677 340-1784 340-1793 340-1800 370-1205 370-1206 370-1230 370-1319 370-1319 501-1354 530-1434 530-1466 530-1826 540-1800 SCSI Term
PAGE 266
Sun4/II: Parts - System - Sun-4/330 2. Wire harness 530-1469 is not field repairable or replaceable. 3. The 1.3GB SCSI Disk does not fit into Tray 540-1757 or 540-1758. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068e.htm (3 von 3) [25.04.
PAGE 267
Sun4/II: Parts - System - Sun-4/370/470 Sun-4/370/470 12-Slot VMEbus Logic Enclosure Front View Rear View http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068f.htm (1 von 7) [25.04.
PAGE 268
Sun4/II: Parts - System - Sun-4/370/470 CODE 1 1 1 2 3 3 4 5 6 6 NS NS 7 8 7&8 NS NS 9 10 NS NS NS 10 NS NS PART # 501-1439 501-1598 501-1832 340-1898 340-1877 540-1846 330-1192 330-1210 330-1284 340-2249 340-1901 540-1731 540-1849 540-1731 240-0558 240-0557 340-1871 540-1748 330-1212 330-1213 340-1936 540-2136 330-1373 340-2491 DESCRIPTION 12-Slot Backplane, Pressfit (obsolete) 1 12-Slot Backplane, Pressfit 12-Slot Backplane, Pressfit with DC Harness Cutout Top Cover Side Cover (obsolete) Side Cover Ref
PAGE 269
Sun4/II: Parts - System - Sun-4/370/470 11 NS NS NS NS NS 12 540-1751 Fan Tray Assembly, 9 Fans 2 530-1482 Fan Tray DC Harness for Fan 540-1732 540-1732 DC Fan Assembly, 150 CFM 530-1640 Fan Tray DC Harness for Fan 370-1732 370-1732 DC Fan Assembly, 150 CFM 370-1214 DC Fan Assembly with connector, 150 CFM 240-8503 Caster (obsolete) 1. The Sun 4400 CPU is not supported in the 501-1439 Backplane. 2.
PAGE 270
Sun4/II: Parts - System - Sun-4/370/470 12-Slot VMEbus Logic Enclosure - Continued CODE NS NS NS NS 13 14 NS 15 16 17 17 18 19 20 20 21 21 21 PART # 260-3719 340-1878 540-1848 540-1749 530-1480 501-1493 140-1019 530-1494 340-1892 300-1047 300-1089 340-1903 501-1496 530-1498 530-1729 370-1230 370-1319 370-1319 DESCRIPTION Sun-4/370 Logo Rear Bezel (obsolete) Rear Bezel Rear Bumper Backplane to Interface PCB DC Harness Interface PCB (SCSI Bus and DC Power) 15 Amp Fuse SCSI Bus Internal Command Cable, 25.
PAGE 271
Sun4/II: Parts - System - Sun-4/370/470 22 23 23 23 23 23 24 NS NS NS NS 530-1500 370-1206 370-1247 370-1297 370-1205 370-1347 530-1499 530-1638 530-1249 530-1593 530-1829 800-3255 Internal SCSI Bus Cable, 1.2M 2 150MB Tape Drive, Full-Height, QIC-150 45/60MB Tape with MT02, Full-Height, QIC-11/24 2.3GB 8 mm Tape Drive, Full-Height 150MB Tape Drive, Half-Height, QIC-150 644MB CD-ROM, Half-Height Peripheral Tray DC Harness DC "Y" Harness, Half-Height Peripherals External SCSI Cable, DD-50SA to DD-50SA, 1.
PAGE 272
Sun4/II: Parts - System - Sun-4/370/470 CODE 1 2 3 4 5 6 6 7 NS NS 8 NS NS 9 NS NS PART # 501-1832 540-1846 300-1089 340-1898 330-1192 330-1210 330-1284 540-1939 240-0558 240-0557 340-2291 340-2292 340-2444 540-2136 330-1373 340-2491 DESCRIPTION 12-Slot Backplane, Pressfit with DC Harness Cutout Side Cover 925 Watt Power Supply Top Cover Blank Bezel Insert Front Bezel Half-Height Insert Front Bezel Full-Height Insert Front Bezel Assembly Miniball Receptacle Miniball Fastener Front EMI Cover, without Swit
PAGE 273
Sun4/II: Parts - System - Sun-4/370/470 10 NS NS NS 11 12 NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS 540-1751 370-1214 530-1640 370-1732 340-2129 340-2293 150-1785 260-3615 260-3616 530-1676 370-1319 370-1319 370-1205 370-1206 370-1297 370-1347 370-1377 530-1675 530-1842 530-1829 540-1848 540-1749 800-3255 Fan Tray Assembly, 9 Fans 1 DC Fan Assembly with Connector, 150 CFM Fan Tray DC Harness for Fan 370-1732 DC Fan Assembly, 150 CFM Caster Rear EMI Cover External Active Terminator, 50-Pin SCSI-2 SP
PAGE 274
Sun4/II: Parts - System - Sun-4/390/490 Sun-4/390/490 SCSI Peripheral Trays CODE PART # DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00690.htm (1 von 6) [25.04.
PAGE 275
Sun4/II: Parts - System - Sun-4/390/490 1 2 3 4 5 6 7 8 9 NS 10 11 11 12 13 14 15 16 NS NS NS NS NS NS NS NS NS NS NS NS NS NS NS 540-1865 340-2000 530-1474 240-1202 530-1507 340-1832 340-1999 540-1865 340-2143 530-1642 530-1641 530-1638 340-2145 340-2146 340-2305 240-1372 340-2148 240-0258 340-2144 240-0646 370-1205 370-1206 370-1297 370-1347 530-1381 530-1435 530-1593 530-1508 530-1501 530-1502 530-1568 530-1792 530-1793 530-1829 530-1842 SCSI Tray, Versions 1 and 2 (Shipped before 4/90) SCSI Tray SCSI
PAGE 276
Sun4/II: Parts - System - Sun-4/390/490 CODE PART # DESCRIPTION 1 540-1719 Blower Assembly, 2 Blowers 540-1840 Centrifugal Fan Assembly 530-1560 Cable, 32.5 cm, Fan to Terminal 530-1561 Cable, 86.5 cm, AC Input to Terminal 150-1393 Capacitor 240-1614 Terminal Block 2 340-1833 Front RFI Shield 3 240-1372 M4 0.7 x 10 mm Screw http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00690.htm (3 von 6) [25.04.
PAGE 277
Sun4/II: Parts - System - Sun-4/390/490 4 5 6 6 7 7 NS NS NS NS NS NS NS NS 150-1397 530-1506 300-1065 300-1047 501-1498 501-1597 540-1869 180-1189 180-1190 230-0203 240-0146 260-3618 260-3619 530-1534 800-3265 800-3259 Indicator LED Indicator LED Cable 1200 Watt Power Supply 925 Watt Power Supply (obsolete) 16-slot Backplane, Pressfit (obsolete) 16-slot Backplane, Pressfit Load Resistor Assembly (obsolete) 1 Power Cord (230V) Power Cord (240V) Cable Tie, 4" Cable Clamp SPARCserver 390 Logo SPARCserver 4
PAGE 278
Sun4/II: Parts - System - Sun-4/390/490 CODE 1 2 3 4 5 6 7 PART # 340-1884 540-1857 540-1858 240-1630 340-1840 340-1885 240-1372 DESCRIPTION Anti-Tilt Panel Vented Panel Assembly Upper Panel Assembly, 1/2" and 1/4" Tape, Hinged #6-32 Ballstud Top Panel Side Restraint Bracket, Upper M4 0.7 x 10 mm Sem Screw http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00690.htm (5 von 6) [25.04.
PAGE 279
Sun4/II: Parts - System - Sun-4/390/490 8 9 10 11 12 13 14 15 16 16 16 16 17 18 19 NS NS NS NS NS NS NS NS NS NS NS NS 540-1718 540-2393 340-1881 340-1848 340-1886 240-1717 240-1373 230-1418 370-1155 370-1156 300-1263 300-1264 240-1655 340-1845 340-2047 230-1166 230-1170 230-1177 240-1738 240-1739 240-1748 340-1835 340-1913 340-2057 340-2138 530-1303 800-3259 Frame Assembly Keyswitch Assembly (replaced 540-1285) Hinge Bracket Side Panel Side Restraint Bracket, Lower Caster (replaced 370-1210) M4 0.
PAGE 280
Sun4/II: PARTS BREAKDOWN - Introduction Parts Breakdown This section contains illustrations, part numbers, and descriptions of Sun Systems, Options, Boards, Input Devices, Monitors, and Printers. Options such as processor modules, SIMMs, and SBus cards are not included in Volume II. Internal system peripheral options are not included in the Disk, Removable Media, or Miscellaneous chapters. Parts listed as (obsolete) or (obs) are no longer used to build new systems.
PAGE 281
Sun4/II: PARTS BREAKDOWN - Introduction 370-xxxx-xx 500-xxxx-xx 501-xxxx-xx 520-xxxx-xx 525-xxxx-xx 530-xxxx-xx 540-xxxx-xx 555-xxxx-xx 560-xxxx-xx 570-xxxx-xx 595-xxxx-xx 596-xxxx-xx 600-xxxx-xx 700-xxxx-xx 704-xxxx-xx 790-xxxx-xx 794-xxxx-xx 800-xxxx-xx 801-xxxx-xx 802-xxxx-xx 804-xxxx-xx 807-xxxx-xx 813-xxxx-xx 825-xxxx-xx 855-xxxx-xx 950-xxxx-xx OEM Part Untested PCB Tested PCB Programmed IC Programmed IC Cable Assembly FRU Assembly Shipping Kit Electro Mechanical Assembly Top Level Option Assembly Co
PAGE 282
Sun4/II: PARTS BREAKDOWN - Introduction Higher/Lower Base Number Examples PART # 300-1281 300-1286 501-2925 501-2940 501-3001 501-2324 501-2924 501-2961 DESCRIPTION RELEASE DATE SC2000 Power Supply 3/28/95 SC2000 Power Supply 9/19/94 SM71 SuperSPARC 2.4.5 9/28/95 SM71 SuperSPARC 2.3 6/05/95 SM71 SuperSPARC 2.4.3 8/14/95 SS20 CPU 1/10/94 SS20 CPU 9/14/95 SS20 CPU* 7/12/95 * 501-2961 is a screened and re-labeled 501-2324.
PAGE 283
Sun4/II: PARTS BREAKDOWN - Introduction R T Japan (used by Fuji Xerox) Milpitas, California (Re-Manufacturing) Tools PART # 250-1028 250-1024 250-1025 250-1026 250-1017 250-1029 250-1030 250-1031 250-1032 250-1033 250-1034 250-1035 250-1036 250-1037 250-1038 250-1039 250-1040 250-1041 250-1042 250-1043 250-1044 250-1045 250-1046 250-1047 250-1048 250-1049 250-1050 250-1051 250-1052 250-1053 250-1054 250-1055 250-1056 250-1057 250-1058 DESCRIPTION Field Engineer Toolkit (Jensen JTK-679-1) T9 Torx Screwdr
PAGE 284
Sun4/II: PARTS BREAKDOWN - Introduction 250-1059 250-1060 250-1061 250-1062 250-1063 250-1064 250-1065 250-1066 250-1067 250-1068 4.5 mm Nutdriver Blade 5 mm Nutdriver Blade 5.
PAGE 285
Sun4/II: PARTS BREAKDOWN - Introduction 250-1072 250-1074 250-1088 330-1145 330-1646 330-1836 330-1852 345-1131 345-1132 None None 370-1906 370-1907 560-1763 345-1184 1/2" x 1/2" Thin-Head Wrench for 56" Rack Levelers 10-Inch End Cutter Sun ESD Mat with Sun Logo Disposable ESD Mat SS10 and SS20 SIMM Insertion Tool (order 560-1936) SS20 Fan Installation Tool SS Voyager Power Supply Extraction Tool SIMM Extraction Wire Tool (obsolete) SIMM Extraction Wire Tool (obsolete) T8 Torx Blade (Xcelite 99-8XTD) T10
PAGE 286
Sun4/I: Slot Assignment - Contents Slot Assignment Board Installation Notes VMEbus Bus Grant and Interrupt Acknowledge SCSI Host Adapter Assemblies Sun-4 Architecture Sun-4/110 Sun-4/150 Sun-4/260 Sun-4/280 Sun-4/310 Sun-4/330 Sun-4/350 Sun-4/360 Sun-4/370 Sun-4/380 Sun-4/390 Sun-4/470 Sun-4/490 Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004c2.htm [25.04.
PAGE 287
Sun4/I: Slot Assignment - Board Installation Notes Board Installation Notes Backplane Slot Assignment Charts Each system chart lists the PCB slot assignments in order of descending priority. In the charts A,B,C... indicates the preferred location for a specific board. An A is the most preferred location. An a indicates that a board requires more than one slot if Memory, Frame Buffer, or other options are installed. Multiple capital letters (AA, BBB...) indicate a board requires more than one slot.
PAGE 288
Sun4/I: Slot Assignment - Board Installation Notes Sun 4400 CPU 1. The Sun 4400 CPU requires 12-slot Backplane 501-1598 or 501-1382. The Sun 4400 CPU is not supported in the 501-1439 12-slot Backplane. 2. The Sun 4400 CPU requires 16-slot Backplane 501-1498-02 or 501-1597. Sun 3200, 3400, and 4200 ECC Memory 1. 501-1092 or 501-1117 BackpIanes. Install the first Memory board in Slot 6. Install 220/270 Terminating Resistor 120-1613-01 at location F-34 or F-54 on the Memory board.
PAGE 289
Sun4/I: Slot Assignment - Board Installation Notes CG9 with GP2 1. 2. 3. 4. The CG9 P2 bus must be enabled (SW3-1, OFF). The CG9 must be installed in cardcage slots that share the P2 bus with the GP2. This configuration is not supported with the TAAC-1. The CG9 is not supported without the GP2. TAAC-1 1. The TAAC-1 requires three slots. Install backplane jumpers BG3 and IACK in all three slots. 2. The TAAC-1 is not supported with the CG9 and GP2 GXP Graphics Options. Xylogics 450 Disk Controller 1.
PAGE 290
Sun4/I: Slot Assignment - Board Installation Notes BOARD 1 2 3 4 5 6 7 8 ALM-1 ALM-2 & MCP VECTOR VECTOR 0x88 0x8b 0x89 0x8a 0x8a 0x89 0x8b 0x88 0xa0 0xa1 0xa2 0xa3 ALM-1 501-1157 (Pedestal Systems) The ALM-1 must be installed in Slots 11 and 12. Install Backplane Jumpers BG3 and IACK in Slot 11. Remove Backplane Jumper BG3 from Slot 12. MAPkit 1. The MAPkit requires two slots. Remove Backplane Jumpers BG3 and IACK from the slot that contains the MAPkit board nearest to Slot 1.
PAGE 291
Sun4/I: Slot Assignment - Board Installation Notes SBus Expansion Subsystem Board The SBus Expansion Subsystem Board does not use the VMEbus. Systech MTI-800, MTI-850, MTI-1600, and MTI-1650 Tables A and B provide reference information for Systech boards packaged in kits. Table A identifies the ALM boards in a Sun PCB kit. Columns 2, 3, and 4 provide the Sun PCB part number, a board description, and the Systech part number for individual boards within each set.
PAGE 292
Sun4/I: Slot Assignment - Board Installation Notes Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005f3.htm (6 von 6) [25.04.
PAGE 293
Sun4/I: Slot Assignment - VMEbus Bus Grant and Interrupt Acknowledge VMEbus Bus Grant and Interrupt Acknowledge This chart shows how the Bus Grant In/Out and Interrupt Acknowledge In/Out signals are connected on the board. Wired signals are not used. Open signals are selected with backplane jumpers. Option signals are enabled on the board and on the backplane.
PAGE 294
Sun4/I: Slot Assignment - VMEbus Bus Grant and Interrupt Acknowledge Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005f4.htm (2 von 2) [25.04.
PAGE 295
Sun4/I: Slot Assignment - SCSI Host Adapter Assemblies SCSI Host Adapter Assemblies 1. Use the slot assignment charts for systems with the 501-1138 or 501-1217 SCSI Assembly if there is no SCSI Host Adapter installed in a Sun-3/180, Sun-3/280, or Sun-4/280. 2. Sun 3x2 Adapter, 501-1269, Option 160A, is connected to J2 Rows A and C. There is no external connector. 3. Sun 3x2 Adapter, 501-1191, Option 160B, is not connected to J2 Rows A and C. There is no external connector. 4.
PAGE 296
Sun4/I: Slot Assignment - SCSI Host Adapter Assemblies Memory Boards With SCSI ASSY # MEMORY BD # DESCRIPTION SCSI HOST 501-1147 501-1079 2/50 0MB 501-1045 501-1172 501-1121 3/75 0MB 501-1045 Memory Boards That Can Use A 501-1045 SCSI MEMORY BD # DESCRIPTION 501-1020 2/50 1MB 501-1046 2/50 2MB 501-1047 2/50 4MB 501-1067 2/50 3MB 501-1079 2/50 0MB 501-1111 3/75 2MB 501-1121 3/75 0MB 501-1122 3/75 4MB Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.
PAGE 297
Sun4/I: Slot Assignments - Sun-4/110 Sun-4/110 SHUNTS BG3 IACK Out Out In Out In Out In Out In Out Out Out Out Out In Out SLOT POSITION 1 2 3 Sun 4100 CPU (1) A A MCP A ALM-2 A Color (2) A HSI A Ethernet A FDDI A IPC (3) A BOARD References 1. Sun Systems Cardcage Slot Assignments and Backplane Configuration Procedures, 813-2004-16. 2. Cardcage Slot Assignments and Backplane Configuration Procedures for the Sun 4/110, 813-2053-05. Last updated: December 2, 1996 Comments and Suggestions http://lios.
PAGE 298
Sun4/I: Slot Assignments - Footnotes for Sun-4/110/150/260/280 Footnotes to Slot Assignments for Sun-4/110/150/260/280 NOTE # PART # 1 501-1199 501-1237 501-1462 501-1463 501-1464 501-1465 501-1512 501-1513 501-1514 501-1515 501-1516 501-1517 501-1656 501-1657 501-1658 501-1659 501-1660 501-1661 501-1247 501-1248 501-1371 501-1374 501-1518 501-1532 501-1314 501-1466 BOARD Sun 4100 CPU (-03 FAB) 8MB w/o FPU Sun 4100 CPU (-03 FAB) 8MB w FPU Sun 4100 CPU (-03 FAB) 16MB w/o FPU Sun 4100 CPU (-03 FAB) 16MB w F
PAGE 299
Sun4/I: Slot Assignments - Footnotes for Sun-4/110/150/260/280 NOTE # PART # BOARD 5 501-1383 TAAC-1 Application Accelerator 501-1447 TAAC-1 Application Accelerator NOTE # PART # 6 501-1102 501-1451 501-1254 501-1576 BOARD 8MB Memory 32MB Memory 32MB Memory 16MB Memory NOTE # PART # BOARD 7 501-1149 Sun-2 SCSI Host Adapter Assembly 501-1170 Sun-3 SCSI Host Adapter Assembly NOTE # PART # BOARD 8 501-1155 Xylogics 472 Tape Controller Assy The 501-1156, CPC Tapemaster Tape Ctlr Assembly is not supported.
PAGE 300
Sun4/I: Slot Assignments - Sun-4/150 Sun-4/150 SHUNTS BG 3 IACK Out Out Out Out In In In In In In In In In Out In Out In Out In Out In Out In Out In Out In Out In Out In Out Out Out Out Out In Out In Out SLOT POSITION 1 2 3 4 5 6 Sun 4100 CPU (1) A A GP (4) A GB A TAAC-1 (5) A B A B A B 1st MCP A B C D E 2nd MCP A B C D 1st ALM-2 A B C D E 2nd ALM-2 A B C D Color (2) A B C D CG5 with GP/GP+ A B CG5 with GP2 A CG9 Color A 1st HSI A B C 2nd HSI A B Ethernet A B C FDDI A B C 1st IPC (3) A B C 2nd IPC (3) A B
PAGE 301
Sun4/I: Slot Assignments - Sun-4/260 Sun-4/260 SHUNTS BG 3 IACK Out Out In In In In In In In In Out Out In In In In In In In In Out Out Out Out In Out In Out In Out In Out In Out In Out In Out In Out Out Out Out Out Out Out Out Out Out Out In In Out Out In In In Out In Out Out Out Out Out Out Out In Out In Out In Out SLOT POSITION 1 2 3 4 5 6 7 8 9 10 11 12 Sun 4200 CPU A 1st Memory (6) A 2nd Memory (6) A 3rd Memory (6) A 4th Memory (6) A GP (4) A GB A TAAC-1 (5) E F DC B A E F DC B A E F D C B A ALM-1 A
PAGE 302
Sun4/I: Slot Assignments - Sun-4/260 In Out Out Out Out In In In In Out Out Out Out Out Out Out Out Out 4th IPC (3) 1st Tape Ctlr (8) 2nd Tape Ctlr (8) 1st Disk Ctlr (9) 2nd Disk Ctlr (9) Color (2) CG5 w GP/GP+ CG5 w GP2 CG9 Color A J AB C GAB C B CD AB C AB AB C AB D E F D E F E D C D C G F E D E D H G F E F E I A B A B References 1. Sun Systems Cardcage Slot Assignments and Backplane Configuration Procedures, 813-2004-16. 2.
PAGE 303
Sun4/I: Slot Assignments - Sun-4/260 In In In Out Out Out Out Out In Out In In In Out Out Out In Out Out Out Out Out Out Out Out In Out In Out Out Out Out Out Out 2nd ALM-2 3rd ALM-2 4th ALM-2 1st Channel Adapter 2nd Channel Adapter 1st MAPkit In In In Out Out Out Out In In In In Out Out Out Out Out Out Out Out Out Out Out 2nd IPC (3) 3rd IPC (3) 4th IPC (3) 1st Tape Ctlr (8) 2nd Tape Ctlr (8) 1st Disk Ctlr (9) 2nd Disk Ctlr (9) Color (2) CG5 w GP/GP+ CG5 w GP2 CG9 Color AB A AB AB D C B D C B A D C
PAGE 304
Sun4/I: Slot Assignment - Sun-4/280 Sun-4/280 with 501-1167 SCSI Host Adapter SHUNTS BG3 IACK Out Out In In In In In In In In Out Out In In In In In In In In Out Out Out Out Out Out Out Out In Out In Out In Out In Out In Out In Out In Out In Out Out Out Out Out Out Out Out Out Out Out In In Out Out In In In Out In Out In Out In Out SLOT POSITION 1 2 3 4 5 6 7 8 9 10 11 12 Sun 4200 CPU A 1st Memory (6) A 2nd Memory (6) A 3rd Memory (6) A 4th Memory (6) A GP (4) A GB A TAAC-1 (5) E F DC B A E F DC B A E F D
PAGE 305
Sun4/I: Slot Assignment - Sun-4/280 In In Out Out Out In In In In Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out 1st HSI 2nd HSI Ethernet 1st FDDI 2nd FDDI 1st IPC (3) 2nd IPC (3) 3rd IPC (3) 4th IPC (3) 1st Tape Ctlr (8) 2nd Tape Ctlr (8) 1st Disk Ctlr (9) 2nd Disk Ctlr (9) 3rd Disk Ctlr (10) 4th Disk Ctlr (10) AB A AB AB A AB A C B C C B C B A D C D D C D C B A E D E E D E D C B A F E F F E F E D C B A AB A G F G G F G F E D C B C B A H G H H G H G F E D C D
PAGE 306
Sun4/I: Slot Assignment - Sun-4/280 In In In Out Out Out Out In In In In In In In In Out Out Out Out Out In Out In In In In In In In Out Out Out In In In In Out Out Out Out Out In In In Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out In Out In Out Out Out Out Out Out Out Out Out Out Out Out Out TAAC-1 (5) E E E 1st ALM-1 2nd ALM-1 3rd ALM-1 SCSI (11) 1st MCP 2nd MCP 3rd MCP 4th MCP 1st ALM-2 2nd ALM-2 3rd ALM-2 4th ALM-2 1st Channel Adapter 2nd Channel Adapter 1st MAPkit 2nd MAPkit
PAGE 307
Sun4/I: Slot Assignment - Sun-4/280 Out Out 4th Disk Ctlr (10) A B C References 1. Sun Systems ardcage Slot Assignments and Backplane Configuration Procedures, 813-2004-16. 2. Cardcage Slot Assignments and Backplane Configuration Procedures for Sun 4/200 Systems with Double-Height Backpanels, 813-2071-05.
PAGE 308
Sun4/I: Slot Assignment - Sun-4/280 Out In Out In In In Out Out In In In In In In Out Out Out In In In In Out Out Out Out Out Out Out In Out In Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out 1st MAPkit 2nd MAPkit 1st HSI 2nd HSI Ethernet SCSI (12) Color (2) CG5 w GP/GP+ CG5 w GP2 CG9 Color 1st HSI 2nd HSI Ethernet 1st FDDI 2nd FDDI 1st IPC (3) 2nd IPC (3) 3rd IPC (3) 4th IPC (3) 1st Tape Ctlr (8) 2nd Tape Ctlr (8) 1st Disk Ctlr (9) 2nd Disk Ctlr (9) 3rd Disk C
PAGE 309
Sun4/I: Slot Assignment - Sun-4/280 Sun-4/280 with Double-Height Backpanel with 501-1138 or 501-1217 SCSI SHUNTS BG3 IACK Out Out In In In In In In In In Out Out In In In In In In In In Out Out Out Out Out Out In Out In Out In Out In Out In Out In Out In Out In Out Out Out Out Out Out Out Out Out Out Out In In Out Out In In Out Out In Out In Out In Out SLOT POSITION 1 2 3 4 5 6 7 8 9 10 11 12 Sun 4200 CPU AA 1st Memory (6) A 2nd Memory (6) A 3rd Memory (6) A 4th Memory (6) A GP (4) A GB A TAAC-1 (5) E DC
PAGE 310
Sun4/I: Slot Assignment - Sun-4/280 In In In Out Out Out In In In In Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out CG9 Color 1st HSI 2nd HSI Ethernet 1st FDDI 2nd FDDI 1st IPC (3) 2nd IPC (3) 3rd IPC (3) 4th IPC (3) 1st Tape Ctlr (8) 2nd Tape Ctlr (8) 1st Disk Ctlr (9) 2nd Disk Ctlr (9) 3rd Disk Ctlr (10) Out Out 4th Disk Ctlr (10) AB A AB AB A AB A C B C C B C B A AB A AB A C B C B A D C D D C D C B A D C D C B E D E E D E D C B E D E D C F E F F E F E D C F E
PAGE 311
Sun4/I: Slot Assignment - Sun-4/280 In In In Out Out Out In In In In In In In In Out Out Out Out Out Out Out Out Out In In In In In In Out Out Out In In In In Out Out Out Out Out In In In Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out In Out Out Out Out Out Out Out Out Out Out Out Out Out TAAC-1 (5) 1st ALM-1 2nd ALM-1 3rd ALM-1 1st MCP 2nd MCP 3rd MCP 4th MCP 1st ALM-2 2nd ALM-2 3rd ALM-2 4th ALM-2 1st Channel Adapter 2nd Channel Adapter 1st MAPkit 2nd MAPkit SCSI (12) Col
PAGE 312
Sun4/I: Slot Assignment - Sun-4/280 Out Out 4th Disk Ctlr (10) A B C D References 1. Sun Systems Cardcage Slot Assignments and Backplane Configuration Procedures, 813-2004-16. 2. Sun-4/200 Cardcage Slot Assignments and Backplane Configuration Procedures, 813-2037-05.
PAGE 313
Sun4/I: Slot Assignment - Sun-4/280 Out Out Out Out Out In Out In Out In In In In In In Out Out Out In In In In Out Out Out Out Out Out Out Out Out Out Out In Out In Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out 1st Channel Adapter 2nd Channel Adapter 1st MAPkit AB C AB C A A AB AB 2nd MAPkit SCSI (12) Color (2) CG5 w GP/GP+ CG5 w GP2 CG9 Color 1st HSI 2nd HSI Ethernet 1st FDDI 2nd FDDI 1st IPC (3) 2nd IPC (3) 3rd IPC (3) 4th IPC (3) 1st Tape Ctlr (8) 2nd Tape Ctlr (8)
PAGE 314
Sun4/I: Slot Assignment - Sun-4/310 Sun-4/310 SHUNTS BG 3 Out In In In In In In Out In In IACK Out In Out Out Out Out Out Out Out Out SLOT POSITION BOARD 1 2 3 Sun 4300 CPU (1) A A Memory (2) A B Color (3) A B 1st MCP A B 2nd MCP A 1st ALM-2 A B 2nd ALM-2 A Ethernet (4) B A 1st IPC (5) B A 2nd IPC (5) A Reference SPARCsystem 350 and 310 Cardcage Slot Assignments and Backplane Configuration Procedures, 800-5722-10. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.
PAGE 315
Sun4/I: Slot Assignment - Footnotes for Sun-4/310/330/350/360/370/380/390 Footnotes to Slot Assignments for Sun-4/310/330/350/360/370/380/390 NOTE # PART # 1 501-1247 501-1374 501-1402 501-1443 501-1532 501-1316 501-1408 501-1466 501-1544 501-1565 501-1697 501-1742 501-1682 501-1739 BOARD MG3 P4 Mono Frame Buffer CG6 P4 Color Frame Buffer MG4 P4 Mono Frame Buffer CG4 P4 Color Frame Buffer CG6 P4 Color Frame Buffer 8MB Sun 4300 CPU 1MB SIMM Module 1MB SIMM Module 1MB SIMM Module 1MB SIMM Module 1MB SIMM Mo
PAGE 316
Sun4/I: Slot Assignment - Footnotes for Sun-4/310/330/350/360/370/380/390 NOTE # PART # 6 501-1268 GP2 501-1139 GP+ BOARD NOTE # PART # BOARD 7 501-1381 TAAC-1 Application Accelerator 501-1447 TAAC-1 Application Accelerator NOTE # PART # 8 501-1316 501-1408 501-1466 501-1544 501-1565 501-1697 BOARD 8MB Sun 4300 CPU 1MB SIMM Module 1MB SIMM Module 1MB SIMM Module 1MB SIMM Module 1MB SIMM Module NOTE # PART # BOARD 9 501-1217 Sun-3 SCSI Host Adapter Assembly NOTE # PART # 10 501-1436 501-1723 501-131
PAGE 317
Sun4/I: Slot Assignment - Footnotes for Sun-4/310/330/350/360/370/380/390 13 501-1166 Xylogics 451 Disk Controller Assembly 501-1249 Xylogics 7053 Disk Controller NOTE # PART # BOARD 14 501-1249 Xylogics 7053 Disk Controller NOTE # PART # BOARD 15 501-1539 ISP-80 IPI Disk Controller 501-1855 ISP-80 IPI Disk Controller Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00606.htm (3 von 3) [25.04.
PAGE 318
Sun4/I: Slot Assignments - Sun-4/330 Sun-4/330 SHUNTS BG3 Out In In In In Out Out Out In In In Out In Out - IACK Out Out Out Out Out Out Out Out Out Out Out Out Out Out - SLOT POSITION BOARD 9U 6U 3U 1 2 3 4A 5A 4B 5B Sun 4300 CPU (8) A a 1st MCP B A 2nd MCP B A 1st ALM-2 B A 2nd ALM-2 B A VX B A MVX A GP (6) A Color (3) B A 1st HSI B A 2nd HSI A Ethernet (4) B A IPC B A SCSI (9) B A 1st Memory (10) A B 2nd Memory (10) A References 1.
PAGE 319
Sun4/I: Slot Assigments - Sun-4/350 Sun-4/350 SHUNTS BG3 IACK Out Out In In Out Out Out Out In In In In In In In Out In Out In Out In Out Out Out Out Out Out Out In In Out Out In In In Out In Out In Out Out Out Out Out In Out In Out In Out SLOT POSITION 1 2 3 4 5 6 Sun 4300 CPU (1) A A Memory (2) A GP (6) A CG9 A TAAC-1 (7) A B A B A B 1st MCP E A B C D 2nd MCP D A B C 1st ALM-2 E A B C D 2nd ALM-2 D A B C SunLink D A B C Channel Adapter D A B C 1st Mapkit D A B C D A B C 2nd Mapkit C A B C A B Color (3)
PAGE 320
Sun4/I: Slot Assignment - Sun-4/360 Sun-4/360 SHUNTS BG3 IACK Out Out In In Out Out In Out In In In In In In In In Out Out In In In Out In Out In Out In Out In Out In Out In Out In Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out In Out In Out In Out SLOT POSITION 1 2 3 4 5 6 7 8 9 10 11 12 Sun 4300 CPU (1) A A Memory (2) AA GP (6) A CG9 A A GB A TAAC-1 (7) A A A ALM-1 A A SCSI Adapter (11) A 1st MCP KAB CD E F G H I J 2nd MCP J AB CD E F G H I 3rd MCP I AB CD E F G H 4th MCP H
PAGE 321
Sun4/I: Slot Assignment - Sun-4/360 Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ff.htm (2 von 2) [25.04.
PAGE 322
Sun4/I: Slot Assignment - Sun-4/370 Sun-4/370 SHUNTS BG3 IACK Out Out In In Out Out Out Out In Out Out Out In In In In In In In In In Out In Out In Out In Out In Out In Out In Out In Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out In Out In Out In Out Out Out SLOT POSITION 1 2 3 4 5 6 7 8 9 10 11 12 Sun 4300 CPU (1) A a Memory (2) A VX A B C MVX A B CG9 A B GP (6) A GB A TAAC-1 (7) AB CD E F AB CD E F AB C D E F 1st MCP AB CD E F G H 2nd MCP AB CD E F G 3rd MCP AB C D E
PAGE 323
Sun4/I: Slot Assignment - Sun-4/370 References 1. SPARCsystem 370 Cardcage Slot Assignments and Backplane Configuration Procedures, 813-2079-11. 2. Sun-3 SCSI Hosts Adapter Installation Manual, 813-1015-11. 3. Cardcage Slot Assignments and Backplane Configuration Procedures for the VX and MVX Accelerators, 800-5426-06. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00600.htm (2 von 2) [25.04.
PAGE 324
Sun4/I: Slot Assignment - Sun-4/380 Sun-4/380 SHUNTS BG3 IACK Out Out In In Out Out In Out In In In In In In In In Out Out Out Out Out Out In Out In Out In Out In Out In Out In Out In Out In Out Out Out Out Out In Out In Out In Out Out Out Out Out Out Out Out Out Out Out Out Out SLOT POSITION 1 2 3 4 5 6 7 8 9 10 11 12 Sun 4300 CPU (1) A a Memory (2) A a GP (6) A CG9 A B GB A TAAC-1 (7) A A A 1st ALM-1 A 2nd ALM-1 A 3rd ALM-1 A 1st MCP KAB CD E F G H I J 2nd MCP J AB CD E F G H I 3rd MCP I AB CD E F G H 4
PAGE 325
Sun4/I: Slot Assignment - Sun-4/380 References SPARCsystem 360 & SPARCserver 380 Cardcage Slot Assignments and Backplane Configuration Procedures, 813-2088-11. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00601.htm (2 von 2) [25.04.
PAGE 326
Sun4/I: Slot Assignment - Sun-4/390 Sun-4/390 SHUNTS BG3 IACK Out Out In In Out Out Out Out Out Out In In In In In In In Out In Out In Out In Out In Out In Out In Out In Out In Out In Out In Out In Out Out Out Out Out Out Out Out Out Out Out In Out In Out Out Out Out Out Out Out In Out In Out In In Out Out Out Out Out Out BOARD 4300 CPU (1) Memory (2) VX MVX GP2 TAAC-1 (7) 1st MCP 2nd MCP 3rd MCP 4th MCP 1st ALM-2 2nd ALM-2 3rd ALM-2 4th ALM-2 5th ALM-2 6th ALM-2 7th ALM-2 8th ALM-2 1st Channel Adapter
PAGE 327
Sun4/I: Slot Assignment - Sun-4/390 Out Out In In In Out Out Out Out Out 3rd IPI Ctlr (15) 4th IPI Ctlr (15) CG5 CG5 w GP2 CG9 AB C D E F G H I A B C D E F G H AB CD E F G H I J K A B A B References 1. Sun SPARCserver 390 Card Cage Slot Assignments and Backplane Configuration Procedure, 813-2067-10. 2. Cardcage Slot Assignments and Backplane Configuration Procedures for the VX and MVX Accelerators, 800-5426-06. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.
PAGE 328
Sun4/I: Slot Assignment - Sun-4/470 Sun-4/470 SHUNTS BG3 IACK Out Out In In In In In In In In In In In In Out Out Out Out Out Out In In In In In In In Out In Out In Out In Out In Out In Out In Out In Out In Out In Out Out Out Out Out Out Out Out Out Out Out Out Out In Out In Out Out Out Out Out Out Out Out Out Out Out SLOT POSITION 1 2 3 4 5 6 7 8 9 10 11 12 Sun 4400 CPU A a 1st Memory (1) A 2nd Memory (1) A 3rd Memory (1) A 4th Memory (1) A 5th Memory (1) A 6th Memory (1) A VX A B C MVX A B GP2 A B TAAC-
PAGE 329
Sun4/I: Slot Assignment - Sun-4/470 Out Out Out Out Out Out Out Out Out Out In In In In Out Out Out Out Out Out Out Out Out Out Out Out Out In 1st NC400 2nd NC400 3rd NC400 4th NC400 1st SMD Ctlr (5) 2nd SMD Ctlr (5) 1st IPI Ctlr (6) 2nd IPI Ctlr (6) 3rd IPI Ctlr (6) 4th IPI Ctlr (6) CG5 CG5 w GP2 CG9 Prestoserve AB C D AB C A B A A B A A B A C B C B A A B C A A AB C D E D C D C B A D B B F References 1.
PAGE 330
I: Slot Assignment - Footnotes for Sun-4/470/490 Footnotes to Slot Assignments for Sun-4/470/490 NOTE # PART # 1 501-1402 501-1374 501-1532 501-1333 501-1721 BOARD MG4 P4 Mono Frame Buffer CG6 P4 Color Frame Buffer CG6 P4 Color Frame Buffer 32MB ECC Memory 128MB ECC Memory NOTE # PART # BOARD 2 501-1381 TAAC-1 Application Accelerator 501-1447 TAAC-1 Application Accelerator NOTE # PART # 3 BOARD 501-1217 Sun-3 SCSI Host Adapter Assembly NOTE # PART # BOARD 4 501-1584 Sun 3E Ethernet Controller Assembl
PAGE 331
Sun4/I: Slot Assignment - Sun-4/490 Sun-4/490 SHUNTS BG3 IACK Out Out In In In In In In In In In In In In Out Out Out Out Out Out In In In In In In In Out In Out In Out In Out In Out In Out In Out In Out In Out In Out In Out In Out Out Out Out Out Out Out Out Out Out In In Out Out Out Out Out Out Out SLOT POSITION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Sun 4400 CPU A a 1st Memory (1) A 2nd Memory (1) A 3rd Memory (1) A 4th Memory (1) A 5th Memory (1) A 6th Memory (1) A VX A B C MVX A B GP2 A B TAAC-1 (2)
PAGE 332
Sun4/I: Slot Assignment - Sun-4/490 Out Out Out Out Out Out Out Out Out Out Out Out Out Out In In In Out Out Out Out In Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out Out In 3rd Ethernet (4) 1st FDDI 2nd FDDI 1st NC400 2nd NC400 3rd NC400 4th NC400 5th NC400 6th NC400 1st IPI Ctlr (6) 2nd IPI Ctlr (6) 3rd IPI Ctlr (6) 4th IPI Ctlr (6) 5th IPI Ctlr (6) CG5 CG5 w GP2 CG9 1st SMD Ctlr (5) 2nd SMD Ctlr (5) 3rd SMD Ctlr (5) 4th SMD Ctlr (5) Prestoserve A AB C AB A B D C B A
PAGE 333
Sun4/I: Backplane - Contents Backplane Backplane Information Sun-4/110/310 Sun-4/150/350 Sun-4/260/280/360/380 Sun-4/370 Sun-4/370/470 / SS670MP Sun-4/330 / SS630MP Sun-4/390/490 / SS690MP Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004bf.htm [25.04.
PAGE 334
Sun4/I: Backplane - Backplane Information Backplane Information This section contains bus signal charts and backplane layout illustrations. VMEbus Backplane Cardcage slot numbers are stamped, printed, or labeled on the sheet metal near the card ejectors. VMEbus backplane jumpers are silk-screened on the cardcage as Px00, Px01, Px02, Px03, and Px04 or Jx00, Jx01, Jx02, Jx03, and Jx04; where x represents the card slot number.
PAGE 335
Sun4/I: Backplane - Backplane Information 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SYSCLK GND DS1* DS0* WRITE* GND DTACK* GND AS* GND IACK* IACKIN IACKOUT* AM4 A07 A06 A05 A04 A03 A02 A01 -12V +5V BG3IN* BG3OUT* BR0* BR1* BR2* BR3* AM0 AM1 AM2 AM3 GND SERCLK SERDAT GND IRQ7* IRQ6* IRQ5* IRQ4* IRQ3* IRQ2* IRQ1* +5VSTDBY +5V SYSFAIL* BERR* SYSRESET* LWORD* AM5 A23 A22 A21 A20 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A09 A08 +12V +5V VMEbus J2/P2 Pinouts PIN 1 2 3 4 5 6 7 8 9 10
PAGE 336
Sun4/I: Backplane - Backplane Information 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined D17 D18 D19 D20 D21 D22 D23 GND D24 D25 D26 D27 D28 D29 D30 D31 GND +5V User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined Us
PAGE 337
Sun4/I: Backplane - Backplane Information 20 21 22 23 24 25 26 27 28 29 30 31 32 +5V +5V +5V +5V +5V +5V +12V +12V -12V -12V -5V -5V -5V User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined GND GND GND GND GND GND +12V +12V -12V -12V -5V -5V -5V Pressfit Backplanes Pressfit Backplane production began in June 1987.
PAGE 338
Sun4/I: Backplane - Backplane Information 501-1354 5-Slot Backplane Memory board options plug into connector J3, Slots 4 and 5, on the 501-1354 backplane. The Sun P2 bus connects Slots 1, 4, and 5 as shown below. J102 Row A Connects to J403 Row A and J503 Row A J102 Row C Connects to J403 Row C and J503 Row C J103 Row B Connects to J403 Row B and J503 Row B Cardcage Slots 4 and 5 share a private bus that connects signals between J2/P2, Row A and J2/P2, Row C. These slots are used with 6U VMEbus boards.
PAGE 339
Sun4/I: Backplane - Backplane Information The 501-1439 Backplane terminates J2/P2, Row C, Pins 75 and 96 with a 40.2 Ohm resistor and a 47pf capacitor. The 501-1598 and 501-1832 Backplanes terminate J2/P2, Row C, Pins 75 and 96 with a 200 Ohm resistor. Termination is jumper selectable. The Sun 4400 CPU is not supported in the 501-1439 Backplane. The function of the backplane jumpers is shown below.
PAGE 340
Sun4/I: Backplane - Backplane Information J8xx J9xx J10xx J11xx J12xx J13xx J14xx J15xx J16xx BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 8 BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 9 BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 10 BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 11 BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 12 BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 13 BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 14 BG0-3IN to BG0-3Out and IACKIN to IACKOUT on sl
PAGE 341
Sun4/I: Backplane - Backplane Information P2 Bus A A A A A A A B C D D D 16-Slot VMEbus Backplane 501-1498 and 501-1597 Slot 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 P2 Bus A A A A A A A B C D E E F F F G Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f6.htm (8 von 8) [25.04.
PAGE 342
Sun4/I: Backplane - Sun-4/110/310 Sun-4/110/310 501-1127 Pressfit Power: 1.3 Amps @ +5Vdc 6.5 Watts P1 Power Pinouts 1-2 3-4 5 6 7 8 -5 GND +12 GND -12 GND Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f7.htm [25.04.
PAGE 343
Sun4/I: Backplane - Sun-4/150/350 Sun-4/150/350 501-1128 Pressfit Power: 1.3 Amps @ +5Vdc 6.5 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f8.htm (1 von 2) [25.04.
PAGE 344
Sun4/I: Backplane - Sun-4/150/350 P1 Power Pinouts 1-2 3-4 5 6 7 8 -5 GND +12 GND -12 GND Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f8.htm (2 von 2) [25.04.
PAGE 345
Sun4/I: Backplane - Sun-4/260/280/360/380 Sun-4/260/280/360/380 501-1092 501-1117 Pressfit Power 1.3 Amps @ +5Vdc 6.5 Watts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f9.htm [25.04.
PAGE 346
Sun4/I: Backplane - Sun-4/370 Sun-4/370 501-1439 Pressfit Test Points Description TEST POINT 1 2 3 4 TEST DESCRIPTION POINT +5 5 GND 6 +12 Motor 7 -12 8 DESCRIPTION +12 -5.2 Chassis ground Ground http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fa.htm (1 von 2) [25.04.
PAGE 347
Sun4/I: Backplane - Sun-4/370 Power 2.1 Amps @ +5Vdc 10.5 Watts Note The LED positions on the backplane and the descriptions molded into the front cover do not match. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fa.htm (2 von 2) [25.04.
PAGE 348
Sun4/I: Backplane - Sun-4/370/470 / SS670MP Sun-4/370/470 / SS670MP 501-1598 Pressfit Test Points Description TEST POINT 1 2 3 4 TEST DESCRIPTION POINT +5 5 GND 6 +12 Motor 7 -12 8 DESCRIPTION +12 -5.2 Chassis ground Ground http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fb.htm (1 von 3) [25.04.
PAGE 349
Sun4/I: Backplane - Sun-4/370/470 / SS670MP Power 2.1 Amps @ +5Vdc 10.5 Watts Sun-4/370/470 / SS670MP 501-1832 Pressfit Test Points Description TEST TEST POINT DESCRIPTION POINT DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fb.htm (2 von 3) [25.04.
PAGE 350
Sun4/I: Backplane - Sun-4/370/470 / SS670MP 1 2 3 4 +5 GND +12 Motor -12 5 6 7 8 +12 -5.2 Chassis ground Ground Power: 2.1 Amps @ +5Vdc 10.5 Watts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fb.htm (3 von 3) [25.04.
PAGE 351
Sun4/I: Backplane - Sun-4/330 / SS630MP Sun-4/330 / SS630MP 501-1354 Pressfit Power 2.0 Amps @ +5Vdc 10.0 Watts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fc.htm [25.04.
PAGE 352
Sun4/I: Backplane - Sun-4/390/490 / SS690MP Sun-4/390/490 / SS690MP 501-1498 Pressfit Test Points Description TEST POINT 1 2 3 4 TEST DESCRIPTION POINT +5 5 GND 6 +12 Motor 7 -12 8 DESCRIPTION +12 -5.2 Chassis ground Ground http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fd.htm (1 von 3) [25.04.
PAGE 353
Sun4/I: Backplane - Sun-4/390/490 / SS690MP Power 2.1 Amps @ +5Vdc 10.5 Watts Sun-4/390/490 / SS690MP 501-1597 Pressfit Test Points Description TEST TEST POINT DESCRIPTION POINT DESCRIPTION 1 +5 5 +12 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fd.htm (2 von 3) [25.04.
PAGE 354
Sun4/I: Backplane - Sun-4/390/490 / SS690MP 2 3 4 GND +12 Motor -12 6 7 8 -5.2 Chassis ground Ground Power 2.1 Amps @ +5Vdc 10.5 Watts Note The Load Resistor is only used with the 925W power supply. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fd.htm (3 von 3) [25.04.
PAGE 355
Sun4/I: Miscellaneous - Contents Miscellaneous Floating Point Unit-2 (FPU2) SunIPC 6U to 9U VMEbus Adapter VMEbus to Multibus Adapter Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004bc.htm [25.04.
PAGE 356
Sun4/I: Miscellaneous - Floating Point Unit-2 (FPU2) Floating Point Unit-2 (FPU2) Sun-4/110/150 Option 154 501-1384 4/110/150 Option Parts Front Bracket 340-1743 Rear Bracket 340-2163 4-40 Screw 240-1196 J100 Jumper Settings PINS SETTING DESCRIPTION 1-2 In TI chip on board 3-4 In No Tristate on all output 5-6 In TI8847/TI8837 7-8 Out Enable chaining mode http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a5.htm (1 von 3) [25.04.
PAGE 357
Sun4/I: Miscellaneous - Floating Point Unit-2 (FPU2) Notes 1. The 501-1384 FPU2 is supported only on CPU boards 501-1512, 501-1513, 501-1514, 501-1515, 501-1516, and 501-1517. 2. Remove the Weitek ALU (U202) and Multiplier (U201) from the 4/110/150CPU to install the FPU2. 3. Diagnostics fpurel and fputest for SunOS 4.0 and 4.0.1 are on the 1.0 FPU2 Patch Tape. Reference FPU-2 Installation Manual for Sun-4/100 Systems, 800-3067. Floating Point Unit-2 (FPU2) Sun-4/260/280 Option 154 501-1387 http://lios.
PAGE 358
Sun4/I: Miscellaneous - Floating Point Unit-2 (FPU2) J100 Jumper Settings PINS SETTING DESCRIPTION 1-2 In TI chip on board 3-4 In No Tristate on all output 5-6 In TI8847/TI8837 7-8 Out Enable chaining mode Note Diagnostics fpurel and fputest for SunOS 4.0 and 4.0.1 are on the 1.0 FPU2 Patch Tape. Reference FPU-2 Installation Manual for Sun-4/100 Systems, 800-3067. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a5.
PAGE 359
Sun4/I: Miscellaneous - SunIPC SunIPC Sun-4/260/280/330/360/370/380/390 Options SUNIPC / SUNIPC-87 501-1125 501-1214 w/o 80287 w 80287 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a6.htm (1 von 3) [25.04.
PAGE 360
Sun4/I: Miscellaneous - SunIPC Power: 5.6 Amps @ +5Vdc 28.
PAGE 361
Sun4/I: Miscellaneous - SunIPC SW3-1 SW3-2 SW3-3 SW3-4 SW3-5 SW3-6 SW3-7 SW3-8 On On Off Off Off On Off On A23 A22 A21 A20 A19 A18 A17 A16 VME Address 3E0000; device pc3 SWITCH SETTING DESCRIPTION SW3-1 On A23 SW3-2 On A22 SW3-3 Off A21 SW3-4 Off A20 SW3-5 Off A19 SW3-6 Off A18 SW3-7 Off A17 SW3-8 On A16 Notes 1. The Sun 3200 CPU must be >=501-1100-08 or >=501-1206-06. 2. Boards with Aeroscientific FAB date code 8639 may randomly exhibit "interrupt level2" errors.
PAGE 362
Sun4/I: Miscellaneous - 6U to 9U VMEbus Adapter 6U to 9U VMEbus Adapter Option 160A 501-1269 with P2A & P2C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a7.htm (1 von 2) [25.04.
PAGE 363
Sun4/I: Miscellaneous - 6U to 9U VMEbus Adapter 6U to 9U VMEbus Adapter Option 160B 501-1191 without P2A & P2C Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a7.htm (2 von 2) [25.04.
PAGE 364
Sun4/I: Miscellaneous - VMEbus to Multibus Adapter VMEbus to Multibus Adapter Option 161 501-1054 Power: 2.0 Amps @ +5Vdc 10.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a8.htm (1 von 2) [25.04.
PAGE 365
Sun4/I: Miscellaneous - VMEbus to Multibus Adapter Note: There are no LED, switch, or cable openings in the backpanel. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a8.htm (2 von 2) [25.04.
PAGE 366
Sun4/I: Communication - Contents Communication Multibus Sun-2 Ethernet Controller VMEbus to Multibus Adapter with Sun-2 Ethernet Sun-3/E Ethernet Assembly Systech MTI-800/1600 Controller Systech MTI-850/1650 Controller VMEbus to Multibus Adapter with MTI-1600 VMEbus to Multibus Adapter with MTI-1650 VMEbus to Multibus Adapter with MTI-1650A VMEbus MAPKIT Asynchronous Line Multiplexor-2 Multiprotocol Communication Processor SunLink Channel Adapter High-speed Serial Interface (HSI) FDDI/DX Sun Network CoProc
PAGE 367
Sun4/I: Communication - Sun-2 Ethernet Controller Sun-2 Ethernet Controller Sun-4/110/150/260/280 Sun-4/310/330/350/360/370/380/390 Option 450 501-1004 Power: 6.0 Amps @ +5Vdc 0.5 Amps @ +12Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00512.htm (1 von 2) [25.04.
PAGE 368
Sun4/I: Communication - Sun-2 Ethernet Controller 36.0 Watts Jumper and Switch Settings JUMPER PINS SETTING DESCRIPTION J101 1-2 In Level 1 Ethernet 1-2 Out Level 2 Ethernet J400 1-2 Out M.BIG Select J401 1-2 Out M.
PAGE 369
Sun4/I: Communication - VMEbus to Multibus Adapter VMEbus to Multibus Adapter with Sun-2 Ethernet Sun-4/110/150/260/280/310/330/350/360 Sun-4/370/380/390 Option 450 501-1153 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00513.htm (1 von 2) [25.04.
PAGE 370
Sun4/I: Communication - VMEbus to Multibus Adapter Power: 5.8 Amps @ +5Vdc 29.
PAGE 371
Sun4/I: Communication - Sun-3/E Ethernet Assembly Sun-3/E Ethernet Assembly Sun-4/390/470/490 Option 452 501-1584 Power: 4.1 Amps @ +5Vdc 20.5 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00514.htm (1 von 3) [25.04.
PAGE 372
Sun4/I: Communication - Sun-3/E Ethernet Assembly Notes 1. Board revision 501-8027-06 or 501-1584-01 is required for use in any SPARC CPU based system. 2. When used with the Sun-4400 CPU, 501-1381, the board revision must be >=501-8027-07 or the assembly must be >=501-1584-02.
PAGE 373
Sun4/I: Communication - Sun-3/E Ethernet Assembly Reference Sun SunNet Ethernet/VME Controller Configuration Procedures, 813-2082-10. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00514.htm (3 von 3) [25.04.
PAGE 374
Sun4/I: Communication - Systech MTI-800/1600 Controller Systech MTI-800/1600 Controller Asychronous Line Multiplexer 1 (ALM-1) Sun-4/260/280 Options 480 / 481 370-1047 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00515.htm (1 von 2) [25.04.
PAGE 375
Sun4/I: Communication - Systech MTI-800/1600 Controller Switch Settings mt0 Defaults DIP SWITCH SETTING DESCRIPTION SW2 1 Off Address select A15 2 Off Address select A14 3 Off Address select A13 4 Off Address select A12 5 Off Address select A11 6 On Address select A10 7 On Address select A9 8 Off Address select A8 SW3 1 Off Address select A7 2* Off Address select A6 3* On Address select A5 4 Off Address select A4 5 Off Address select A3 6 Off Select 16-bit addresses 7 Off One stop bit 8 On One stop bit SW4
PAGE 376
Sun4/I: Communication - Systech MTI-850/1650 Controller Systech MTI-850/1650 Controller Asychronous Line Multiplexer 1 (ALM-1) Sun-4/260/280 Options 480 / 481 370-1099 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00516.htm (1 von 3) [25.04.
PAGE 377
Sun4/I: Communication - Systech MTI-850/1650 Controller Switch Settings mt0 Defaults DIP SWITCH SETTING DESCRIPTION SW2 1 Off Address select A15 2 Off Address select A14 3 Off Address select A13 4 Off Address select A12 5 Off Address select A11 6 On Address select A10 7 On Address select A9 8 Off Address select A8 SW3 1 Off Address select A7 2* Off Address select A6 3* On Address select A5 4 Off Address select A4 5 Off Address select A3 6 Off Select 16-bit addresses 7 Off One stop bit 8 On One stop bit SW4
PAGE 378
Sun4/I: Communication - Systech MTI-850/1650 Controller W1 W2 W3 W4 Out Out In Out W5 W6 W7 Out In In +12Vdc routing to data cable disabled -12Vdc routing to data cable disabled Normal transfer acknowledge delay Extra 100 nsec delay during transfer acknowledge Byte swap enable Byte swap disable Enable BPRO References 1. Sun-3/180 16-Channel Asynchronous Line Multiplexer Configuration Procedures, 813-2008. 2. Asynchronous Line Multiplexer Configuration Procedures, 813-2003.
PAGE 379
Sun4/I: Communication - VMEbus to Multibus Adapter VMEbus to Multibus Adapter with Systech MTI-1600 Sun-4/260/280 Option 481 501-1157-01 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00517.htm (1 von 2) [25.04.
PAGE 380
Sun4/I: Communication - VMEbus to Multibus Adapter Power: 7.1 Amps @ +5Vdc 0.6 Amps @ +12Vdc 0.4 Amps @ -12Vdc 47.5 Watts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00517.htm (2 von 2) [25.04.
PAGE 381
Sun4/I: Communication - VMEbus to Multibus Adapter VMEbus to Multibus Adapter with Systech MTI-1650 Sun-4/260/360 Option 481 501-1157-02 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00518.htm (1 von 3) [25.04.
PAGE 382
Sun4/I: Communication - VMEbus to Multibus Adapter Power: 7.1 Amps @ +5Vdc 0.6 Amps @ +12Vdc 0.4 Amps @ -12Vdc 47.
PAGE 383
Sun4/I: Communication - VMEbus to Multibus Adapter Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00518.htm (3 von 3) [25.04.
PAGE 384
Sun4/I: Communication - VMEbus to Multibus Adapter VMEbus to Multibus Adapter with Systech MTI-1650A Sun-4/260/280/360/380 Option 481 501-1165 Power: 7.1 Amps @ +5Vdc 0.6 Amps @ +12Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00519.htm (1 von 2) [25.04.
PAGE 385
Sun4/I: Communication - VMEbus to Multibus Adapter 0.4 Amps @ -12Vdc 47.
PAGE 386
Sun4/I: Communication - MAPKIT MAPKIT Sun-4/260/280/390 501-1202 Notes 1. Install the Token Bus Controller in the left slot of the adapter. 2. Install the Token Bus Modem in the right slot of the adapter. 3. The Token Bus Controller and Token Bus Modem are sold by INI. http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051a.htm (1 von 2) [25.04.
PAGE 387
Sun4/I: Communication - MAPKIT Jumper Settings JUMPER PINS J1 1-2 4-6 5-7 9-11 J2 3-5 4-6 J3 3-4 J4 1-2 3-4 5-6 7-8 11-12 13-14 J5 9-10 J6 5-6 J7 9-10 J8 1-2 J9 2-1 J13 1-2 VALUE DESCRIPTION 3 Bus request level 3 Bus request level 16 sec Watchdog timer 0x900 Short I/O address Bus Boot 3 3 512K Normal Normal Boot configuration VME host interrupt VME host interrupt Memory size Clock parameters Clock parameters Power: 4.9 Amps @ +5Vdc 0.3 Amps @ +12Vdc 0.1 Amps @ -12Vdc 29.
PAGE 388
Sun4/I: Communication - Asynchronous Line Multiplexor-2 Asynchronous Line Multiplexor-2 Sun-4/110/150/260/280 Sun-4/310/330/350/360/370/380/390/470/490 SS600MP 501-1203 Power: 7.0 Amps @ +5Vdc 0.2 Amps @ -5Vdc 36.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051b.htm (1 von 3) [25.04.
PAGE 389
Sun4/I: Communication - Asynchronous Line Multiplexor-2 Jumper and Switch Settings JUMPER J0201 J0202 J0202 J1501 J1501 J1502 J1502 J1503 PINS SETTING DESCRIPTION 1-2 In Test jumper for oscillator 32 Bit In VME address bus size 24 Bit Out RS-232 In Enables RS-232 for ALM-2 RS-449 Out Not used for ALM-2 RS-232 In Enables RS-232 for ALM-2 RS-449 Out Not used for ALM-2 1-2 In Test jumper for oscillator ADDRESS BIT A 1 6 SWITCH and SETTING 1 mcp0 @ 0x01000000 1 mcp1 @ 0x01010000 0 mcp2 @ 0x01020000 1 mcp3 @
PAGE 390
Sun4/I: Communication - Asynchronous Line Multiplexor-2 Reference Asynchronous Line Multiplexor-2 Configuration Procedures, 813-2042. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051b.htm (3 von 3) [25.04.
PAGE 391
Sun4/I: Communication - Multiprotocol Communication Processor Multiprotocol Communication Processor Sun-4/110/150/260/280 Sun-4/310/330/350/360/370/380/390/470/490 SS600MP 501-1221 Power: 7.0 Amps @ +5Vdc 0.2 Amps @ -5Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051c.htm (1 von 2) [25.04.
PAGE 392
Sun4/I: Communication - Multiprotocol Communication Processor 36.
PAGE 393
Sun4/I: Communication - SunLink Channel Adapter SunLink Channel Adapter Sun-4/260/280/350/360/370/380/390/470/490 SS670MP / SS690MP 370-1128 501-1460 Board Set Board Set Backpanel and Connectors Power: 8.6 Amps @ +5Vdc 43.0 Watts Notes 1. Replace 370-1128 with 501-1460. Refer to FCO A0003-1. 2. The Sun-3/110 and Sun 3004 CPU must be 501-1134-06, 501-1163-09, 501-1164-09, or greater. All 501-1208 and 501-1209 revisions are usable. 3.
PAGE 394
Sun4/I: Communication - SunLink Channel Adapter Reference SunLink Channel Adapter Configuration Procedures, 813-2040-10. CIO Board http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051d.htm (2 von 5) [25.04.
PAGE 395
Sun4/I: Communication - SunLink Channel Adapter IBD Board Jumper Settings JUMPER PINS SETTING DESCRIPTION B1C 7-8 In VME bus request level BR gives level 3 Others Out B1A 2-3 In Bus grant In/Out BG0/BG3 gives level 3 6-7 In 10-11 In 13-14 In 15-16 In B6C All Out VME bus data transfer timeout http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051d.htm (3 von 5) [25.04.
PAGE 396
Sun4/I: Communication - SunLink Channel Adapter B8P B8U B8V 7-8 3-4 5-6 7-8 1-2 3-4 5-6 7-8 1-2 3-4 5-6 7-8 In Out Out Out In Out Out Out In Out Out Out Local processor external bus page selection BS gives page 0 Interrupt acknowledge page selection IACK gives page 0 Interrupt request page selection IREQ gives page 0 and must be the same as IACK LCP Board http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051d.htm (4 von 5) [25.04.
PAGE 397
Sun4/I: Communication - SunLink Channel Adapter Jumper Settings JUMPER JM01 JM02 JM03 JM04 JM05 JM06 JM07 JM08 JM09 JM10 JM11 JM12 JM14 PINS SETTING DESCRIPTION All Out VME BERR timeout 67.1 seconds All Out VME LBERR timeout 107.
PAGE 398
Sun4/I: Communication - High-speed Serial Interface (HSI) High-speed Serial Interface (HSI) Sun-4/110/150/260/280/330/350/390/470/490 501-1338 Power: 5.3 Amps @ +5Vdc 0.3 Amps @ -5Vdc 28.1 Watts Notes 1. SCSI-3 Host Adapter must be >=501-1120-07, >=501-1170-07, >=501-1217-04, or >=501-1236-03. 2. Sun-3/110 CPU must be >=501-1134-06. 3. Sun-3/140/150/160/180 CPU must be >=501-1074-22, >=501-1094-22, >=501-1163-09, http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051e.htm (1 von 3) [25.
PAGE 399
Sun4/I: Communication - High-speed Serial Interface (HSI) >=501-1164-09, or any revision of 501-1208. 4. The minimum operating system is SunOS 4.0. 5. The High-speed Serial Interface is not supported in Solaris >=2.2. Reference SunLink HSI Board Installation/Service Manual, 813-1046-10.
PAGE 400
Sun4/I: Communication - High-speed Serial Interface (HSI) Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051e.htm (3 von 3) [25.04.
PAGE 401
Sun4/I: Communication - FDDI/DX FDDI/DX Sun-4/110/150/260/280/330/350/390/470/490 SS630MP / SS670MP / SS690MP Option 461 501-1276 Power: 11.2 Amps @ +5Vdc 0.1 Amps @ -5Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051f.htm (1 von 3) [25.04.
PAGE 402
Sun4/I: Communication - FDDI/DX 1.9 Amps @ +12Vdc 0.7 Amps @ -12Vdc 87.7 Watts Switch Settings Notes 1. Use 2A subminiature Fuse 150-1174. 2. The Sun 3004 CPU must be 501-1163-09, 501-1164-09 or greater. All 501-1208 revisions are usable. 3. 501-1276-02 or greater is required for use with the SunLink Channel Adapter board. 4. The Sun-4/330 requires Power Supply 300-1072. 5. Set the FDDI Controller Switch 1, Dip 1, to ON if the DMA uses 32-bit addresses. All Sun systems use 32-bit DMA. 6.
PAGE 403
Sun4/I: Communication - FDDI/DX Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051f.htm (3 von 3) [25.04.
PAGE 404
Sun4/I: Communication - Sun Network CoProcessor Sun Network CoProcessor Sun-4/470/490 SS630MP / SS670MP / SS690MP Option 176 370-1396 / 370-1421 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00520.htm (1 von 8) [25.04.
PAGE 405
Sun4/I: Communication - Sun Network CoProcessor Power: 8.0 Amps @ +5Vdc 0.5 Amps 46.0 Watts Interphase Release 1.4 Switch Settings http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00520.htm (2 von 8) [25.04.
PAGE 406
Sun4/I: Communication - Sun Network CoProcessor Address Switches and Address Bit Assignments DIP SWITCH SW1 SW2 SW3 1 A15 A23 A31 2 A14 A22 A30 3 A13 A21 A29 4 A12 A20 A28 5 A11 A19 A27 6 A10 A18 A26 7 A09 A17 A25 8 AM A16 A24 SNC 1.0 and SNC 1.2 Switch Settings http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00520.htm (3 von 8) [25.04.
PAGE 407
Sun4/I: Communication - Sun Network CoProcessor Notes 1. SNC 1.2 requires Sun 4400 CPU 501-1381-09 or 501-1899-01. 2. SNC 1.2 requires IPI Firmware 525-1023-05, 525-1024-10, and 525-1025-10. This firmware is installed on ISP-80 IPI Controller 501-1539-10 and 501-1855-04. 3. Under Interphase Release 1.4, the VME address space of the fifth NC400 and the Prestoserve board is at 0x800000.
PAGE 408
Sun4/I: Communication - Sun Network CoProcessor References 1. 2. 3. 4. 5. NC300/NC400 Network CoProcessor Release 1.4 Installation Manual. Sun Network CoProcessor 1.0 Installation Manual, 800-6881-10. Sun Network CoProcessor 1.2 Installation Manual, 800-6881-11. Sun Network CoProcessor 1.2 Product Note, 801-5133-10. Writing Device Drivers, 800-3851-10. Sun Network CoProcessor Sun-4/470/490 SS630MP / SS670MP / SS690MP Option 176 370-1696 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.
PAGE 409
Sun4/I: Communication - Sun Network CoProcessor Power: 8.0 Amps @ +5Vdc 0.5 Amps 46.0 Watts SNC 1.2 Jumper Settings http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00520.htm (6 von 8) [25.04.
PAGE 410
Sun4/I: Communication - Sun Network CoProcessor Address Jumpers and Address Bit Assignments JUMPER ADDRESS BIT JUMPER ADDRESS BIT JUMPER JP1 A31 JP9 A23 JP17 JP2 A30 JP10 A22 JP18 JP3 A29 JP11 A21 JP19 JP4 A28 JP12 A20 JP20 JP5 A27 JP13 A19 JP21 JP6 A26 JP14 A18 JP7 A25 JP15 A17 JP8 A24 JP16 A16 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00520.htm (7 von 8) [25.04.
PAGE 411
Sun4/I: Communication - Sun Network CoProcessor ADDRESS BIT A15 A14 A13 A12 A11 Notes 1. SNC 1.2 requires Sun 4400 CPU 501-1381-09 or 501-1899-01. 2. SNC 1.2 requires IPI Firmware 525-1023-05, 525-1024-10, and 525-1025-10. This firmware is installed on ISP-80 IPI Controller 501-1539-10 and 501-1855-04. 3. SunOS for the Sun 4400 reserves 1 Megabyte of DVMA space for VME32 peripheral devices.
PAGE 412
Sun4/I: Removable Media - Contents Removable Media 1/4" Tape Controller Emulex MT02 CD-ROM Drives Sony CDU-8012 (SunCD) 1/4" Tape Drives 60MB 150MB 8 mm Tape Drives 2.3GB 1/2" Tape Drive HP 88780 Front Load Tape Drive Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004b6.htm [25.04.
PAGE 413
Sun4/I: Removable Media - Emulex MT02 Emulex MT02 Sun-4/260/280/360/380 Options 511 / 514 / 516 370-1061 / 370-1235 LED 1 LED 2 KEY (Green) (Red) STATE 0 = Off 0 0 Power up reset clear 1 = On 1 1 Power up self-test passed LED 1. Blinking, MT02 operating normally. LED 2, ON, Do NOT remove the cartridge. Power 1.5 Amps @ +5Vdc 0.04 Amps @ +12Vdc 8.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b1.htm (1 von 3) [25.04.
PAGE 414
Sun4/I: Removable Media - Emulex MT02 Switch and Jumper Settings DIP SWITCH SWITCH SETTING DESCRIPTION SW1 1 Off Bit 0 2 Off Bit 1 3 On Bit 2-SCSI device address 04 4 Off Not used 5 On Archive Drive (Scorpion) 6 Off 5 On Wangtek Drive (5000E) 6 On 7 Off Drive type 8* Off SCSI bus parity check * The Sun386i Tape assembly, 370-1179, includes the MT02 Controller and the Tape Drive. SW1, Switch 8, is ON for this application.
PAGE 415
Sun4/I: Removable Media - Emulex MT02 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b1.htm (3 von 3) [25.04.
PAGE 416
Sun4/I: Removable Media - Sony CDU-8012 (SunCD) Sony CDU-8012 (SunCD) Sun-4/330/370/390/470/490 SS600MP / SS1000 / SC2000 Options 558 / 559 370-1312 370-1347 Lt Grey Bezel Black Bezel Front View Rear View In the Desktop SunCD Plus Pack, orient the Flex Cable as shown, and plug it into ID SELECT 0 1 2. In the Multi-Tape Backup Tray and SC2000, orient the Cable as shown, and plug it into ID SELECT 0 1 2. JUMPER SETTING DESCRIPTION 1, 2 In SCSI ID 6 Parity In Enable parity http://lios.apana.org.
PAGE 417
Sun4/I: Removable Media - Sony CDU-8012 (SunCD) Power 0.5 Amps @ +5Vdc 0.5 Amps @ +12Vdc 8.5 Watts Notes 1. The Sun CD-ROM requires 1.0 SunCD for SunOS 4.0.3c. 2. Use 370-1347-03 when mounted on-end in the SS630MP. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b2.htm (2 von 2) [25.04.
PAGE 418
Sun4/I: Removable Media - 60MB 1/4" Tape Drive 60MB 1/4" Tape Drive Sun-4/260/280/360/380 Options 515 / 514 / 516 370-1076 370-1103 Wangtech 5099EN24 Wangtech 5099EN24 Archive 5945C Rear View of Wangtech Model 5099EN24 Rear View of Archive Model 5945C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b3.htm (1 von 3) [25.04.
PAGE 419
Sun4/I: Removable Media - 60MB 1/4" Tape Drive Power 1.0 Amps @ +5Vdc 1.9 Amps @ +12Vdc 27.8 Watts Note This tape drive is used with the Emulex MT02. 60MB 1/4" Tape Drive with Emulex MT02 Tape Controller Sun-4/370 Options RR128 / RR129 / RREXP / RREXP-P7 370-1247 370-1179 Archive 5945S Archive 5945S Full-Height Full-Height Black Bezel Lt Grey Bezel Rear View Emulex MT02 Tape Controller Switch Settings DIP SWITCH SETTING SWITCH DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.
PAGE 420
Sun4/I: Removable Media - 60MB 1/4" Tape Drive SW1 1&2 3 1&3 2 4 5 6 7 8 8 Off On On Off Off On Off Off On Off SCSI target 4 SCSI target 4 SCSI target 5 SCSI target 5 Not used Archive tape drive Archive tape drive Drive type Parity check ON for 370-1179 Parity check OFF for 370-1247 Reference 60MB Streaming Tape Drive with SCSI Controller Configuration Procedures, 814-1019. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.
PAGE 421
Sun4/I: Removable Media - 150MB 1/4" Tape Drive 150MB 1/4" Tape Drive Sun-4/330/370/390/470/490 SS630MP / SS670MP / SS690MP / SC2000 Options 539 / 565 / 660 370-1205 370-1206 370-1218 370-1246 Archive 2150S Archive 2150S Archive 2150S Archive 2150S Half-Height Full-Height Half-Height Full-Height Black Bezel Black Bezel Custom Bezel Lt Grey Bezel Rear View Flex Cable In the Desktop Tape Pack, remove the SCSI ID jumpers, orient the Flex Cable as shown, and plug it into the SCSI ID jumper block.
PAGE 422
Sun4/I: Removable Media - 150MB 1/4" Tape Drive Power 0.7 Amps @ +5Vdc 1.5 Amps @ +12Vdc 21.
PAGE 423
Sun4/I: Removable Media - 2.3GB 8 mm Tape Drive 2.3GB 8 mm Tape Drive Sun-4/370/390/470/490 SS670MP / SS690MP Options 566 / 802 / 804 370-1297 370-1405 Exabyte EXB-8200 Exabyte EXB-8200 Black Bezel Lt Grey Bezel Rear View Jumper P2 SCSI ID (MSB) 1 4 In 5 In 3 Out 2 Out 1 Out 0 Out 2 (LSB) 3 Out Out Out In In In In Out Out In Out Out Address Select Switch Cable In the Desktop Storage Module and External Storage Module, orient the Address Select Switch Cable as shown, and plug it into P2. http://lios.
PAGE 424
Sun4/I: Removable Media - 2.3GB 8 mm Tape Drive Power 4.0 Amps @ +5Vdc 1.2 Amps @ +12Vdc 34.4 Watts MX Card Dip Switch U32 SWITCH SETTING DESCRIPTION 1 On Bypass memory test 2 On Enable parity checking 3 On Even byte disconnect 4 Off Report busy status 5 On Variable block mode on power up 6 Off No disconnect during data transfer 7 Off Not used 8 Off P6 cartridge type Manual Eject Switch Notes 1. The 112 Meter Tape part number is 370-1298-01. 2. The Cleaning Kit part number is 370-1318-01. http://lios.
PAGE 425
Sun4/I: Removable Media - 2.3GB 8 mm Tape Drive 3. ECO WO_01575 enabled Parity checking on the MX card. Parity checking is disabled on drives shipped prior to December 1991. References Sun 2.3-Gbyte 8mm Tape Drive Configuration Procedures for 56-Inch Data Center Cabinets, 813-2081. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b5.htm (3 von 3) [25.04.
PAGE 426
Sun4/I: Removable Media - HP 88780 Front Load Tape Drive HP 88780 Front Load Tape Drive Options 680 / 682 / 683 / 684 Read/Write/Format Board 370-1276 Drive Controller Board 370-1277 Single Ended I/O Board 811-1241 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b6.htm (1 von 3) [25.04.
PAGE 427
Sun4/I: Removable Media - HP 88780 Front Load Tape Drive Data Buffer Board 370-1279 NVRAM Reset Procedure 1. Load a scratch tape. 2. Run TEST 150 to write a GCR ID to the scratch tape. 3. Run TEST 128 to store the NVRAM contents to the scratch tape. 4. Remove Power. 5. Install the new Data Buffer Board or new EPROMs. 6. Connect a jumper between locations GND and CLRNV. 7. 8. 9. 10. 11. Apply power. FAIL--0 is displayed when selftest is complete. Remove Power. Remove the jumper. Apply Power.
PAGE 428
Sun4/I: Removable Media - HP 88780 Front Load Tape Drive 12. Run TEST 129 to load NVRAM with the contents stored on tape. 13. Rewind to BOT. 14. Run TEST 99 to calibrate the read channel gain values. Battery Notes 1. The battery part number is 150-1204-01 or 811-1232-01. 2. The battery is not replaceable on boards built after January 1990. Reference Sun Front-Load 1/2-Inch Tape Drive Field Service Manual,800-3447. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.
PAGE 429
Sun4/I: SCSI Disk - Contents SCSI Disk Single Ended SCSI Disk Drives CDC 94171-327/344 (327MB) Micropolis 1588-15 (669MB) Maxtor XT-8760S (669MB) Seagate ST41600N (1.3GB) Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004b3.htm [25.04.
PAGE 430
Sun4/I: SCSI Disk - CDC 94171-327/344 (327MB) CDC 94171-327/344 (327MB) 5 1/4" 3600 RPM Embedded SCSI Sun-4/330/370/470 Options RREXP-P7 / RR129 / RR134 Options 526 / 527 / 530 / 539 555-1005 370-1153 370-1230 w Bracket w/o Bezel 77777107 w/o Bracket w/o Bezel 77777107 3 1/4" Height w/o Bracket w Bezel 77777126 3 1/4" Height End View Ground Select Jumper J3 Drive Select and Option Select Jumper J4 In the External Storage Module, orient the Address Select Switch Cable as shown, and plug it into J4.
PAGE 431
Sun4/I: SCSI Disk - CDC 94171-327/344 (327MB) Terminator Power Source Select Jumper J5 Power 1.5 Amps @ +5Vdc 1.4 Amps @ +12Vdc 24.
PAGE 432
Sun4/I: SCSI Disk - CDC 94171-327/344 (327MB) Address Jumper Settings J4 PIN SETTING DESCRIPTION TARGET 1, 2, 4 Out Drive select Target 0 1 In Drive select Target 1 2 In Drive select Target 2 1, 2 In Drive select Target 3 Notes 1. Remove the terminators from the underside of the drive. 2. Terminate the Sun386i with external terminator 530-1381. 3. Sun-3/470, Sun-4/370, and Sun-4/470 systems with dual option trays are terminated internally on the 501-1493 Interface PCB.
PAGE 433
Sun4/I: SCSI Disk - CDC 94171-327/344 (327MB) Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005de.htm (4 von 4) [25.04.
PAGE 434
Sun4/I: SCSI Disk - Micropolis 1588-15 (669MB) Micropolis 1588-15 (669MB) 5 1/4" 3600 RPM Single Ended SCSI Sun-4/330/370/470 Options 561 / 563 / 565 / 566 370-1319 370-1326 555-1151 FS0013-03-5 Black Bezel Green LED 3 1/4" Height FS0019-01-6 No Bezel No LED 3 1/4" Height FS0019-01-6 No Bezel No LED w Bracket Bottom View Note All other jumpers on this board are set by the manufacturer. Do NOT change these settings. End View http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005df.
PAGE 435
Sun4/I: SCSI Disk - Micropolis 1588-15 (669MB) Option Jumper Settings JUMPER SETTING DESCRIPTION W5 Out Spindle starts at power on W4 Out Enable parity detection W1 In Drive provides internal terminator power W2 Out W11 Out W28 Out Frame ground not connected to logic ground External Storage and Expansion Modules JUMPER SETTING DESCRIPTION W5 Out Spindle starts at power on W4 Out Enable parity detection W1 In Drive provides internal terminator power W2 Out W11 Out W28 In Frame ground connected to logic gro
PAGE 436
Sun4/I: SCSI Disk - Micropolis 1588-15 (669MB) Address Jumper Settings J2 Multi-function Connector PIN SETTING DESCRIPTION 0,1, 2 Out Target 0 0 In Target 1 1 In Target 2 0,1 In Target 3 References 1. 5-1/4" SCSI Disk Drive Installation and Configuration for Sun Office Pedestals, 813-2048-11. 2. Revised Removal/Replacement Procedures for Sun ESM and EEM Storage Units, 814-3044-01. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.
PAGE 437
Sun4/I: SCSI Disk - Maxtor XT-8760S (669MB) Maxtor XT-8760S (669MB) 5 1/4" 3600 RPM Single Ended SCSI Sun-4/330/370/470 Options 561 / 563 / 565 / 566 370-1319 370-1326 555-1151 1098618-B Black Bezel Green LED 3 1/4" Height 1098778-B No Bezel No LED 3 1/4" Height FS0019-01- 6 No Bezel No LED w Bracket Bottom View Note All other jumpers on this board are set by the manufacturer. Do NOT change these settings. End View http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005e0.
PAGE 438
Sun4/I: SCSI Disk - Maxtor XT-8760S (669MB) Address Description The address is set on the J2 Adapter installed in the J2 Auxiliary connector, the Address Select switch on the External Storage Module, or on Jumpers JP35, JP36, and JP37. Set the address at only one location. J2 Adapter Circuitry External Storage Module Orient Pin-1 of Address Select Switch Cable 530-1659 with ID4 on the J2 Adapter. http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005e0.htm (2 von 3) [25.04.
PAGE 439
Sun4/I: SCSI Disk - Maxtor XT-8760S (669MB) J2 Auxiliary Connector with Adapter 811-1682-01 JUMPER SETTING DESCRIPTION 1,2,4 Out Target 0 1 In Target 1 2 In Target 2 1,2 In Target 3 JP35, JP36, and JP37 JUMPER SETTING DESCRIPTION JP35, JP36, JP37 Out Target 0 JP35 In Target 1 JP36 In Target 2 JP35, JP36 In Target 3 Option Jumper Settings JUMPER SETTING DESCRIPTION JP14 In Spindle starts at power on JP38 Out No motor delay at power on JP40 In Enable parity detection JP41 In Drive provides internal termina
PAGE 440
Sun4/I: SCSI Disk - Seagate ST41600N (1.3GB) Seagate ST41600N (1.3GB) 976002-012 Elite-1 Family 5 1/4" 5400 RPM Single Ended SCSI Sun-4/470 / SS630MP / SS670MP Option 571 370-1377 3 1/4" Height Top View End View http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005e1.htm (1 von 3) [25.04.
PAGE 441
Sun4/I: SCSI Disk - Seagate ST41600N (1.3GB) In the Desktop Storage Module, orient Pin-1 of the Address Select Switch Cable with ID2 on J5. Remove all jumpers from J4A. Power 2.4 Amps @ +5Vdc 2.1 Amps @ +12Vdc 37.
PAGE 442
Sun4/I: SCSI Disk - Seagate ST41600N (1.3GB) SCO SCP SWP Out Out In Spinup according to SD0 setting Parity enabled Sweep cycle enabled J01 JUMPER SETTING DESCRIPTION 1-2 The drive supplies TERMPWR to its own terminator. It does not supply TERMPWR to the SCSI bus. 2-4 The drive supplies no TERMPWR. The initiator supplies TERMPWR to the bus. 1-3 In The drive supplies TERMPWR for the external 2-4 In terminator at the end of the daisy chain.
PAGE 443
Sun4/I: SCSI - Contents SCSI ESDI Emulex MD21 VMEbus Sun-2 SCSI Host Adapter Blank SCSI Adapter Assembly Sun-3 SCSI Host Adapter Sun-3/E SCSI/Ethernet Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004b0.htm [25.04.
PAGE 444
Sun4/I: SCSI - Emulex MD21 Emulex MD21 Sun-4/260 Options 504 / 505 / 507 / 509 / 510 / 514 / 516 370-0552 / 370-1236 Power 1.6 Amps @ +5Vdc 8.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005cd.htm (1 von 2) [25.04.
PAGE 445
Sun4/I: SCSI - Emulex MD21 Switch and Jumper Settings DIP DESCRIPTION SWITCH SETTING 1 Off* SCSI BUS ADDRESS/TARGET 2 Off Bit 0-7 3 Off 4 Off Not used 5 Off 512 byte/sector 6 Off Power on spin-up 7 Off Soft errors reported 8 Off Parity disabled * For DeskTop Expansion Shoebox, Dip Switch 1 is ON for Target 1. JUMPER SETTING DESCRIPTION E, F* Out SCSI bus termination power option * Jumpers E and F are not on Emulex Rev MD2110103.
PAGE 446
Sun4/I: SCSI - Sun-2 SCSI Host Adapter Sun-2 SCSI Host Adapter Sun-4/260/280 501-1045 Power 2.8 Amps @ +5Vdc 14.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ce.htm (1 von 5) [25.04.
PAGE 447
Sun4/I: SCSI - Sun-2 SCSI Host Adapter Switch and Jumper Settings JUMPER PINS SETTING DESCRIPTION J500 1-2 Out Bus Grant 0 In 3-4 Out Bus Grant 1 In 5-6 Out Bus Grant 2 In 7-8 In Bus Grant 3 In J501 1-2 In Bus Request 0 3-4 Out Bus Request 1 5-6 Out Bus Request 2 7-8 In Bus Request 3 J502 1-2 Out Bus Grant 0 In 3-4 Out Bus Grant 1 In 5-6 Out Bus Grant 2 In 7-8 In Bus Grant 3 In J600 1-2 Out Interrupt Level 0 and 3-4 Out Interrupt Level 1 J601 5-6 In Interrupt Level 2 7-8 Out Interrupt Level 3 9-10 Out Inte
PAGE 448
Sun4/I: SCSI - Sun-2 SCSI Host Adapter Power 2.7 Amps @ +5Vdc 13.5 Watts Sun-2 SCSI Host Adapter Assembly Sun-4/260 501-1149 with P2A and P2C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ce.htm (3 von 5) [25.04.
PAGE 449
Sun4/I: SCSI - Sun-2 SCSI Host Adapter Power 2.7 Amps @ +5Vdc 13.5 Watts Sun-2 SCSI Host Adapter Assembly Sun-4/280 501-1167 with P2A and P2C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ce.htm (4 von 5) [25.04.
PAGE 450
Sun4/I: SCSI - Sun-2 SCSI Host Adapter Power 2.7 Amps @ +5Vdc 13.5 Watts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ce.htm (5 von 5) [25.04.
PAGE 451
Sun4/I: SCSI - Blank SCSI Adapter Assembly Blank SCSI Adapter Assembly Sun-4/360 501-1666 with P2A and P2C Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005cf.htm [25.04.
PAGE 452
Sun4/I: SCSI - Sun-3 SCSI Host Adapter Sun-3 SCSI Host Adapter Sun-4/260/280/330/370/390/490 501-1236 Power 4.8 Amps @ +5Vdc 24.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d0.htm (1 von 5) [25.04.
PAGE 453
Sun4/I: SCSI - Sun-3 SCSI Host Adapter Switch Settings DIP SWITCH SETTING DESCRIPTION SWITCH SW1* 1 On Address A23 U409 2 On Address A22 3 Off Address A21 4 On Address A20 5 On Address A19 6 On Address A18 7 On Address A17 8 On Address A16 SW2* 1 On Address A23 U408 2 On** Address A22 3 On Address A21 4 On Address A20 5 On Address A19 6 On/Off Not Connected 7 On/Off Not Connected 8 On/Off Not Connected *SW1 and SW2 set the address to 0X200000 for the first SCSI.
PAGE 454
Sun4/I: SCSI - Sun-3 SCSI Host Adapter Sun-3 SCSI Host Adapter Assembly Sun-4/260 501-1170 with P2A and P2C Power 4.8 Amps @ +5Vdc 24.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d0.htm (3 von 5) [25.04.
PAGE 455
Sun4/I: SCSI - Sun-3 SCSI Host Adapter Sun-3 SCSI Host Adapter Assembly Sun-4/280/330/370/390/470/490 501-1217 without P2A and P2C Power 4.8 Amps @ +5Vdc 24.0 Watts Last updated: December 2, 1996 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d0.htm (4 von 5) [25.04.
PAGE 456
Sun4/I: SCSI - Sun-3 SCSI Host Adapter Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d0.htm (5 von 5) [25.04.
PAGE 457
Sun4/I: SCSI - Sun-3/E SCSI/Ethernet Sun-3/E SCSI/Ethernet 501-8027 501-1584 9U Assembly Ethernet Only Power 4.1 Amps @ +5Vdc 20.5 Watts Notes 1. Board revision 501-8027-06 or 501-1584-01 is required for use in any SPARC CPU based system. 2. The fuse is not replaceable. http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d1.htm (1 von 3) [25.04.
PAGE 458
Sun4/I: SCSI - Sun-3/E SCSI/Ethernet 3. When used with the Sun-4400 CPU, 501-1381, the board revision must be >=501-8027-07 or the assembly must be >=501-1584-02. 4. SCSI TERMPWR is provided on boards >=501-8027-07. Reference Sun SunNet Ethernet/VME Controller Configuration Procedures , 813-2082-10.
PAGE 459
Sun4/I: SCSI - Sun-3/E SCSI/Ethernet Note: The SCSI base address under SunOS 3.5 diag is 31000. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d1.htm (3 von 3) [25.04.
PAGE 460
Sun4/I: IPI - Contents IPI IPI Disk Controller ISP-80 / IPI-2 IPI Disk Drives Seagate 97229-11G (911MB) Seagate 97209-12G (1.2GB) Seagate 975002-005 (1.3GB) Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004ad.htm [25.04.
PAGE 461
Sun4/I: IPI - ISP-80 / IPI-2 ISP-80 / IPI-2 Sun-4/390/470/490 SS670MP / SS690MP Options 408 / 418 501-1539 / 501-1855 Power: 11.8 Amps @ +5Vdc 59.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00579.htm (1 von 4) [25.04.
PAGE 462
Sun4/I: IPI - ISP-80 / IPI-2 Base Address Select Switches DIP SWITCH 1 2 3 SW1603 AM0 AM1 A10 SW1602 A16 A17 A18 SW1601 A24 A25 A26 4 A11 A19 A27 5 A12 A20 A28 6 A13 A21 A29 7 A14 A22 A30 8 A15 A23 A31 Switch and Jumper Settings Note Dip Switches 3, 4, and 5 of SW1603, select bits A10, A11, and A12 of the controller base address. These are the only switches changed to configure multiple controllers. http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00579.htm (2 von 4) [25.04.
PAGE 463
Sun4/I: IPI - ISP-80 / IPI-2 Jumper JM2 PINS SETTING DESCRIPTION 1-2 In Enable UART clock ISP-80 / IPI-2 A minimum ISP-80 firmware level is required to support these products. PRODUCT 911MB Disk Prestoserve 1.3GB Disk Dual Port SNC 1.
PAGE 464
Sun4/I: IPI - ISP-80 / IPI-2 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00579.htm (4 von 4) [25.04.
PAGE 465
Sun4/I: IPI - Seagate 97229-11G (911MB) Seagate 97229-11G (911MB) Equipment Number PA8Y2 8" 3600 RPM IPI-2 6MB/Sec Options 716 / 717 / 719 / 720 / 741L / 742L / 743L / 744L / 745L Operator Panel 370-1355 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057a.htm (1 von 4) [25.04.
PAGE 466
Sun4/I: IPI - Seagate 97229-11G (911MB) Note Each drive power-on sequence is delayed for a time equal to five seconds times its address. For example, if the address is 3, the drive starts after a 15-second delay.
PAGE 467
Sun4/I: IPI - Seagate 97229-11G (911MB) I/O Board Rear View Power Connector 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 +24 +24 +24 +24 +24 +24 N/C PWR -12 -5 -5 GND GND +5 +5 RTN RTN RTN OK Dip Switch 1 Settings SWITCH 1 2 3 4 SETTING Open Closed Open Closed DESCRIPTION Drive starts when DC Power is applied Disable Port B Enable Port A Disable internal diagnostics http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057a.htm (3 von 4) [25.04.
PAGE 468
Sun4/I: IPI - Seagate 97229-11G (911MB) 5 6 7 8 9 Open Closed Open Closed Open 1D 3 ID Microcode. Do Not Change 1D 2 " 1D 1 " 1D 0 " Slave/Master spindle sync-slave Notes 1. The 911MB Disk requires minimum ISP-80 firmware 525-1023-05, 525-1024-07, and 525-1025-07. 2. ISP-80 501-1539-05 and 501-1855-01 contain the minimum firmware required by the 911MB Disk. 3. Upgrade lower revision ISP-80 Controller boards with Option X2080A. 4. Use terminator 370-1220-01 on the Port A/B Out connector. 5.
PAGE 469
Sun4/I: IPI - Seagate 97209-12G (1.2GB) Seagate 97209-12G (1.2GB) Equipment Number PA8R2 8" 3600 RPM IPI-2 3MB/Sec Options 706 / 707 / 709 / 710 / 741A / 742A / 743A / 744A / 745A Operator Panel 370-1221 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057b.htm (1 von 4) [25.04.
PAGE 470
Sun4/I: IPI - Seagate 97209-12G (1.2GB) Note Each drive power on sequence is delayed for a time equal to five seconds times its address. For example, if the address is 3, the drive starts after a 15-second delay. 1.
PAGE 471
Sun4/I: IPI - Seagate 97209-12G (1.2GB) I/O Board Rear View Power Connector 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 +24 +24 +24 +24 +24 +24 N/C PWR -12 -5 -5 GND GND +5 +5 RTN RTN RTN OK Dip Switch 1 Settings SWITCH SETTING DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057b.htm (3 von 4) [25.04.
PAGE 472
Sun4/I: IPI - Seagate 97209-12G (1.2GB) 1 2 3 4 5 6 7 8 9 Open Closed Open Closed Open Closed Open Closed Open Drive starts when DC Power is applied Disable Port B Enable Port A Disable internal diagnostics 1D 3 ID Microcode. Do Not Change 1D 2 " 1D 1 " 1D 0 " Slave/Master spindle sync-slave Notes 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Use terminator 370-1220-01 on the Port A/B Out connector. Disable an unused port with the Port Enable/Disable switch. Do not install a terminator on an unused port.
PAGE 473
Sun4/I: IPI - Seagate 975002-005 (1.3GB) Seagate 975002-005 (1.3GB) Equipment Number PA4F2/ST41201K 5 1/4" / 5400 RPM / IPI-2 / 3.25-4.5MB/Sec Sun-4/490 / SS690MP Options 726 / 727 / 728 370-1378 540-2127 w/o Bracket 3 1/2" Height FRU w Bracket Servo Board I/O Board and I/O Transceiver Board http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057c.htm (1 von 3) [25.04.
PAGE 474
Sun4/I: IPI - Seagate 975002-005 (1.3GB) Power: 2.7 Amps @ +5Vdc 2.0 Amps @ +12Vdc 37.5 Watts Servo Board Switch Settings http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057c.htm (2 von 3) [25.04.
PAGE 475
Sun4/I: IPI - Seagate 975002-005 (1.3GB) I/O Transceiver Board Switch Settings Notes 1. The minimum operating system is SunOS 4.1.1. 2. SunOS 4.1.1 and SunOS 4.1.1 Rev B require the 1.3GB Disk Drive Enhancement (format.dat). 3. The 1.3GB Disk requires minimum ISP-80 firmware, 525-1023-05, 525-1024-09, and 525-1025-09. 4. ISP-80 501-1539-09 and 501-1855-03 contain the minimum firmware required by the 1.3GB Disk. 5. Upgrade lower revision ISP-80 Controller boards with Option X2080A. 6.
PAGE 476
Sun4/I: Graphics - Contents Graphics VMEbus GP Graphics Processor GP+ Graphics Processor Plus GP Graphics Buffer CG3 Sun 3160 Color Frame Buffer CG5 Color Frame Buffer GP2 Graphics Processor CG9 24-bit Color Frame Buffer TAAC-1 Application Accelerator VX and MVX Visualization Accelerators Sun-3/E Monochrome Frame Buffer Sun-3/E Color Frame Buffer P4 Bus MG3 ECL Monochrome Frame Buffer MG4 Analog/ECL Frame Buffer CG4 Color Frame Buffer CG6 Color Frame Buffer CG8 24-bit Color Frame Buffer SBus MG1 ECL Mono
PAGE 477
Sun4/I: Graphics - GP Graphics Processor GP Graphics Processor Sun-4/150/260/280/330/350/360/370/380 501-1055 UNIX ID: /dev/gpone0a-d Power GP 16.4 Amps @ +5Vdc 82.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0054d.htm (1 von 3) [25.04.
PAGE 478
Sun4/I: Graphics - GP Graphics Processor Jumper and Switch Settings JUMPER SETTING J1 Out J2 In J3 In J4 Out J5 Out J6 Out J7 In if GB is installed J8 Out J9 Out* J10 Out* J11 Out* J12 Out* J13 Out* J14 In J15 Out J16 Out J17 Out* J18 Out DESCRIPTION GP board ID bit 3 GP board ID bit 4 GP board ID bit 2 GP board ID bit 5 GP board ID bit 1 GP board ID bit 6 GP board ID bit 0 GP board ID bit 7 GND test point GND test point PP halt test point VP halt test point Manual reset test point Main clock connect VP f
PAGE 479
Sun4/I: Graphics - GP Graphics Processor Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0054d.htm (3 von 3) [25.04.
PAGE 480
Sun4/I: Graphics - GP+ Graphics Processor Plus GP+ Graphics Processor Plus Sun-4/150/260/280/330/350/360/370/380 501-1139 UNIX ID: /dev/gpone0a-d Power GP+ 14.6 Amps @ +5Vdc 73.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0054e.htm (1 von 3) [25.04.
PAGE 481
Sun4/I: Graphics - GP+ Graphics Processor Plus Jumper and Switch Settings JUMPER SETTING J1 Out J2 In J3 In J4 Out J5 Out J6 Out J7 In if GB is installed J8 Out J9 Out* J10 Out* J11 Out* J12 Out* J13 Out* J14 In J15 Out J16 Out J17 Out* J18 Out DESCRIPTION GP board ID bit 3 GP board ID bit 4 GP board ID bit 2 GP board ID bit 5 GP board ID bit 1 GP board ID bit 6 GP board ID bit 0 GP board ID bit 7 Ground test point Ground test point PP halt test point VP halt test point Manual reset test point Main clock
PAGE 482
Sun4/I: Graphics - GP+ Graphics Processor Plus Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0054e.htm (3 von 3) [25.04.
PAGE 483
Sun4/I: Graphics - GP Graphics Buffer GP Graphics Buffer Sun-4/150/260/280/360/370/380 501-1058 Power 2.1 Amps @ +5Vdc 10.5 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0054f.htm (1 von 2) [25.04.
PAGE 484
Sun4/I: Graphics - GP Graphics Buffer Jumper and Switch Settings JUMPER SETTING DESCRIPTION J1 Out Ground test point J2 Out Ground test point J3 Out Manual reset test point J4 (2-3) In Graphics buffer = 2MB J5 In/Out* Refresh interval test point bit 0 J6 In/Out* Refresh interval test point bit 1 J7 In/Out* Refresh interval test point bit 2 J8 In/Out* Refresh interval test point bit 2 J9 Out Ground test point J10 Out Ground test point *Hardwired Notes The Sun-2/160 Power Supply requires RC Network, 540-130
PAGE 485
Sun4/I: Graphics - CG3 Sun 3160 Color Frame Buffer CG3 Sun 3160 Color Frame Buffer Sun-4/110/150/260/280/310/330/350/360/370/380 501-1116 501-1089 501-1319 Single Buffered Double Buffered* 1Kx1K *Double buffering requires SunOS 3.5 (Sun-3) or SunOS 4.0 (Sun-4). UNIX ID: /dev/cgtwo0 Power 501-1116 501-1319 and 501-1089 8.2 Amps @ +5Vdc 8.3 Amps@ +5Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00550.htm (1 von 3) [25.04.
PAGE 486
Sun4/I: Graphics - CG3 Sun 3160 Color Frame Buffer 2.9 Amps @ -5Vdc 0.1 Amps @ +12Vdc 0.2 Amps @ -12Vdc 59.0 Watts 3.1 Amps @ -5Vdc 0.1 A mps @ +12Vdc 0.2 Amps @ -12Vcd 61.
PAGE 487
Sun4/I: Graphics - CG3 Sun 3160 Color Frame Buffer References 1. Installation Notes for the GP2 and CG5 Boards, 800-2330. 2. Sun-3 Color Board Configuration Procedures, 813-2030. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00550.htm (3 von 3) [25.04.
PAGE 488
Sun4/I: Graphics - CG5 Color Frame Buffer CG5 Color Frame Buffer Sun-4/110/150/260/280 Sun-4/310/330/350/360/370/380/380 Sun-4/470/490 501-1267 UNIX ID: /dev/cgtwo0 Power 8.8 Amps @ +5Vdc 3.2 Amps @ -5Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00551.htm (1 von 3) [25.04.
PAGE 489
Sun4/I: Graphics - CG5 Color Frame Buffer 0.2 Amps @ +12Vdc 0.1 Amps @ -12Vdc 64.
PAGE 490
Sun4/I: Graphics - CG5 Color Frame Buffer SW3300-1 SW3300-2 SW3300-3 SW3300-4 SW3300-5 SW3300-5 SW3300-6 SW3300-7 SW3300-8 On Off Off Off Off On Off Off Off Selects board 0 Selects board 1 Selects board 2 Selects board 3 P2 Bus not enabled P2 Bus enabled - required if GP2 is installed No connection No connection No connection Jumper Settings JUMPER PINS SETTING DESCRIPTION J600 1-2 In V reset 3-4 Out External vertical blank output to ground 5-6 Out External display buffer A output to 7-8 Out No connecti
PAGE 491
Sun4/I: Graphics - GP2 Graphics Processor GP2 Graphics Processor Sun-3/150/160/180/260/280/460/470/480 Sun-4/150/260/280/330/350/360/370/380 Sun-4/390/470/490 501-1268 UNIX ID: /dev/gpone0a-d http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00552.htm (1 von 2) [25.04.
PAGE 492
Sun4/I: Graphics - GP2 Graphics Processor Power 12.1 Amps @ +5Vdc 60.5 Watts Switch Settings DIP SWITCH SETTING DESCRIPTION U1601-1 Off A18 address decode U1601-2 On A19 address decode U1601-3 On A20 address decode U1601-4 Off A21 address decode U1601-5 On A22 address decode U1601-6 On A23 address decode U1601-7 On/Off Not used U1601-8 On/Off Not used Notes 1. The GP2 is used with the CG5 or CG9. Unbundled software is required for SunOS 3.5, 3.5.1, 3.5.2, Sys4-3.2, and Sys43.2.1.
PAGE 493
Sun4/I: Graphics - CG9 24-bit Color Frame Buffer CG9 24-bit Color Frame Buffer Sun-3/260/460/470/480 Sun-4/150/260/280/330/350/360/370/380/390/470/490 501-1434 UNIX ID: /dev/cgnine0 Power 14.6 Amps @ +5Vdc 73.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00553.htm (1 von 3) [25.04.
PAGE 494
Sun4/I: Graphics - CG9 24-bit Color Frame Buffer Notes 1. 2. 3. 4. The GP2 must be 501-1268-07 when used with CG9. The CG9 is not supported with the GP or GP+. CG9 must be >=501-1434-04 for use with the Xylogics 7053. The CG9 is not supported under OpenWindows Versions 2 or 3.
PAGE 495
Sun4/I: Graphics - CG9 24-bit Color Frame Buffer SW3 S0700 DIP SETTING DESCRIPTION 1 Off P2 Bus enable 2 Off Selects board 3 3 Off Selects board 2 4 Off Selects board 1 5 On Selects board 0 6 On N/C 7 Off N/C 8 On N/C Reference Installation and Configuration Guide for the CG9 Color Frame Buffer, 800-3627. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00553.htm (3 von 3) [25.04.
PAGE 496
Sun4/I: Graphics - TAAC-1 Application Accelerator TAAC-1 Application Accelerator Sun-4/260/280/360/370/380/390/470/490 501-1383 / 501-1447 POP Board UNIX ID: dev/taac0 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00554.htm (1 von 3) [25.04.
PAGE 497
Sun4/I: Graphics - TAAC-1 Application Accelerator Power 23.9 Amps @ +5Vdc 0.4 Amps @ -5Vdc 0.2 Amps @ +12Vdc 123.9 Watts DFB Board DFB Board Jumper and Switch Settings Jumper JB231 ROW SHUNTS 1 B-C DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00554.htm (2 von 3) [25.04.
PAGE 498
Sun4/I: Graphics - TAAC-1 Application Accelerator 2-7* Not Used Base addressing 8 8C - 9B BGIN 9 Empty VMBG IN/OUT 0 10 B-C VMBG IN/OUT 1 11 B-C VMBG IN/OUT 2 12 B-C 12 12D - 13D Enable 50MHz CLK VMBG IN/OUT 3 13 B-C * Jumpers 2-7 are hardwired on board revisions without Switch A26. These boards are not marked with a Sun part number. Jumpers 2-7 are empty on board revisions with Switch A26.
PAGE 499
Sun4/I: Graphics - VX and MVX Visualization Accelerators VX and MVX Visualization Accelerators Board Set 501-1537 / 501-1538 Note Tighten Frontplane Connector screws 1, 2, 3, and 4 in sequence, turning each screw no more than two turns at a time. http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00555.htm (1 von 6) [25.04.
PAGE 500
Sun4/I: Graphics - VX and MVX Visualization Accelerators Notes 1. 2. 3. 4. 5. The minimum operating system is SunOS 4.1.1. The final unbundled software release was SunVision 1.2. The minimum operating system for SunVision 1.2 is SunOS 4.1.2. SunVision 1.2 requires OpenWindows Version 3. The Sun 4300 CPU and the Sun 4400 CPU require EPROM 4.1.1 when the VX is used as the system console. 6. Set the NVRAM locations to the values shown below when the VX is used as the system console.
PAGE 501
Sun4/I: Graphics - VX and MVX Visualization Accelerators Power: 14.0 Amps @ +5Vdc 1.45 Amps @ -5Vdc 88.0 Watts Switch Settings Interrupt Request Switch S0101 SWITCH SETTING REQUEST BIT 1 Up 2 2 Down 1 3 Down 0 4 Up VMRQ http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00555.htm (3 von 6) [25.04.
PAGE 502
Sun4/I: Graphics - VX and MVX Visualization Accelerators VME Bus Address Switch S0102 SWITCH SETTING ADDRESS BIT 1 On A31 2 On A30 3 Off A29 4 Off A28 5 On A27 6 On A26 7 On A25 8 On/Off Not used VX Bus Address Switch S0301 SWITCH SETTING ADDRESS BIT 1 On/Off Not used 2 On/Off Not used 3 On A26 4 On A27 5 On A28 6 On A29 7 On A30 8 On A31 MVX Visualization Accelerator Sun-4/330/370/390/470/490 Pixel Processor 501-1537 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00555.
PAGE 503
Sun4/I: Graphics - VX and MVX Visualization Accelerators Power: 14.0 Amps @ +5Vdc 70.0 Watts Switch and Jumper Settings Clock Jumper J0101 PIN SETTING DESCRIPTION 1-2 In Enable 80MHz clock http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00555.htm (5 von 6) [25.04.
PAGE 504
Sun4/I: Graphics - VX and MVX Visualization Accelerators Bus Request Jumper J0901 PIN SETTING DESCRIPTION 3-4 In VME BUS REQUEST 1 5-6 Out VME BUS REQUEST 2 7-8 In VME BUS REQUEST 3 Bus Grant Jumper J0902 PIN SETTING DESCRIPTION 1-2 In BG2 OUT - BG2 IN 3-4 In BG1 OUT - BG1 IN 5-9 In BGx OUT - BG3 OUT 6-10 In BGx IN - BG3 IN 7 Out BGx OUT 8 Out BGx IN 11-12 In BG0 OUT - BG0 IN Bus Control and Arbitration Jumper J1001 PIN SETTING DESCRIPTION 1-2 In VCC - CTRL 3 Out GND 4 Out VCC 5-6 In GND - MODE Base Add
PAGE 505
Sun4/I: Graphics - Sun-3/E Monochrome Frame Buffer Sun-3/E Monochrome Frame Buffer 501-8020 UNIX ID: /dev/bwtwo0 Power 3.0 Amps @ +5Vdc 15.0 Watts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00556.htm [25.04.
PAGE 506
Sun4/I: Graphics - Sun-3/E Color Frame Buffer Sun-3/E Color Frame Buffer 501-8029 Jumper J100 Settings JUMPER J100 J100 J100 J100 PINS SETTING DESCRIPTION 1-2 In Base address 3-4 Out =FF400000 5-6 In 7-8 Out UNIX ID: /dev/cgtwo0 Power: 4.0 Amps @ +5Vdc 20.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00557.htm (1 von 2) [25.04.
PAGE 507
Sun4/I: Graphics - Sun-3/E Color Frame Buffer Notes 1. The Sun-3/E Color Frame Buffer requires a 3/E CPU, >=501-8028-07. 2. This board requires SunOS 3.5 or greater. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00557.htm (2 von 2) [25.04.
PAGE 508
Sun4/I: Graphics - MG3 ECL Monochrome Frame Buffer MG3 ECL Monochrome Frame Buffer Sun-4/110/150/310/330/350/370/390/470/490 501-1247 501-1637 w 3/80 Backpanel Jumper J5401 Settings JUMPER PINS SETTING DESCRIPTION J5401 1-2 Out Monitor auto select 1-2 In Select 1600 x 1280 resolution 1-2 Out Select 1152 x 900 resolution UNIX ID: /dev/bwtwo0 Power: 501-1247 0.8 Amps @ +5Vdc 1.2 Amps @ -5Vdc 10.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00558.htm (1 von 2) [25.04.
PAGE 509
Sun4/I: Graphics - MG3 ECL Monochrome Frame Buffer Notes 1. Set EEPROM location 0x1f to 20. 2. The auto-select feature requires cable 530-1336 or 530-1359. 3. Hi Resolution Monitor 540-1427 must be Motorola revision T or greater for the auto-select feature to operate. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00558.htm (2 von 2) [25.04.
PAGE 510
Sun4/I: Graphics - MG4 Analog/ECL Frame Buffer MG4 Analog/ECL Frame Buffer Sun-4/310/330/350/370/380/390/470/490 501-1402 w 3/80 Backpane UNIX ID: /dev/bwtwo0 Power: 3.3 Amps @ +5Vdc 16.5 Watts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00559.htm [25.04.
PAGE 511
Sun4/I: Graphics - CG4 Color Frame Buffer CG4 Color Frame Buffer Sun-4/110/150/310/330/350/370/380/390/470/490 501-1248 501-1443 BNC DB13W3 w 3/80 Backpanel J700 Setting PINS SETTING DESCRIPTION 1-2 In Enable clock UNIX ID: dev/cgfour0 and /dev/bwtwo1 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055a.htm (1 von 2) [25.04.
PAGE 512
Sun4/I: Graphics - CG4 Color Frame Buffer Power: 501-1443 3.8 Amps @ +5Vdc 19.0 Watts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055a.htm (2 von 2) [25.04.
PAGE 513
Sun4/I: Graphics - CG6 Color Frame Buffer CG6 Color Frame Buffer Sun-4/110/150/310/330/350/370/380/390/470/490 501-1374 501-1505 501-1532 w 3/80 Backpane JUMPER J100 J500 J501 J900 PINS SETTING DESCRIPTION 1-2 Out Monitor ID 1-2 In V.Y. CLK memory control 1-2 Out OSC 2 CLK 2-3 In 1152 x 900 (on 270-1532 Fab) UNIX ID: /dev/cgsix0 Power 501-1374 501-1505 and 501-1532 3.5 Amps @ +5Vdc 4.9 Amps @ +5Vdc 7.5 Watts 24.5 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055b.
PAGE 514
Sun4/I: Graphics - CG6 Color Frame Buffer Notes 1. Sun-3/60, Sun-4100, and Sun-4300 CPU boards require EPROM Revision 3.0 or greater. 2. Set CPU EEPROM location 0x1F to 0x20. 3. The minimum operating system is SunOS 4.0.3. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055b.htm (2 von 2) [25.04.
PAGE 515
Sun4/I: Graphics - CG8 24-bit Color Frame Buffer CG8 24-bit Color Frame Buffer Sun-4/110/150 501-1371 501-1518 501-1577 BNC DB13W3 w 3/80 Rear Panel DB13W3 UNIX ID: /dev/cgeight0 Power 501-1371 and 501-1518 501-1577 5.5 Amps @ +5Vdc 4.8 Amps @ +5Vdc 27.5 Watts 24.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055c.htm (1 von 2) [25.04.
PAGE 516
Sun4/I: Graphics - CG8 24-bit Color Frame Buffer Notes 1. 2. 3. 4. 5. 6. There are no jumpers or switches on this board. Set CPU EEPROM location 0x1F to 0x20. Requires SunOS 4.0 CG8 or 4.0.3 or greater. SunOS 4.0 CG8 is not upgradeable to 4.0.1. CG8 must be 501-1374-04 or greater for use with Sun 3400 and Sun 4300 CPU boards. The CG8 is not supported under OpenWindows Versions 2 or 3. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.
PAGE 517
Sun4/I: Graphics - MG1 ECL Monochrome Frame Buffer MG1 ECL Monochrome Frame Buffer Sun-4/15/30/40/50/60/65/75 Sun-4/E / SS10 / SS20 / SS600 / SC2000 501-1419 501-8043 w 4/E Backpanel Jumper JMP4 PINS SETTING DESCRIPTION 1-2 In Select 1600 x 1280 resolution 1-2 Out Select 1152 x 900 resolution 1-2 Out Monitor auto select UNIX ID: /dev/bwtwo0 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055d.htm (1 von 2) [25.04.
PAGE 518
Sun4/I: Graphics - MG1 ECL Monochrome Frame Buffer Power: 1.3 Amps @ +5Vdc 6.5 Watts Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055d.htm (2 von 2) [25.04.
PAGE 519
Sun4/I: Graphics - MG2 Analog Frame Buffer MG2 Analog Frame Buffer Sun-4/15/30/40/50/60/65/75 SS4 / SS5 / SS10 / SS20 / SS600 501-1455 501-8062 w 4/E Backpane Jumper JMP5 PINS SETTING DESCRIPTION 1-2 In Select 27C256 EPROM 1-2 Out Select 27C64 EPROM UNIX ID: /dev/bwtwo0 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055e.htm (1 von 3) [25.04.
PAGE 520
Sun4/I: Graphics - MG2 Analog Frame Buffer Power: 0.4 Amps @ +5Vdc 2.0 Watts Note The MG2 Frame Buffer produces a 1-bit Analog output. MG2 Analog Frame Buffer Sun-4/15/30/40/50/60/65/75 SS4 / SS5 / SS10 / SS20 / SS600 501-1561 501-8077 w 4/E Backpane http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055e.htm (2 von 3) [25.04.
PAGE 521
Sun4/I: Graphics - MG2 Analog Frame Buffer UNIX ID: /dev/bwtwo0 Power: 0.3 Amps @ +5Vdc 1.6 Watts Note The MG2 Frame Buffer produces a 1-bit Analog output. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055e.htm (3 von 3) [25.04.
PAGE 522
Sun4/I: Graphics - CG3 Color Frame Buffer CG3 Color Frame Buffer Sun-4/15/30/40/50/60/65/75 SS4 / SS5 / SS10 / SS20 501-1415 501-8044 FAB 270-1415 w 4/E Backpanel UNIX ID: /dev/cgthree0 Power: 0.7 Amps @ +5Vdc 3.5 Watts Last updated: December 2, 1996 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055f.htm (1 von 2) [25.04.
PAGE 523
Sun4/I: Graphics - CG3 Color Frame Buffer Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055f.htm (2 von 2) [25.04.
PAGE 524
Sun4/I: Memory - Contents Memory SIMMs Sun-4/260/280 Sun-4/330 Sun 4300 Sun 4400 Sun-4/E (4MB) Sun-4/E (16MB) Sun-4/E (Combo) Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004a7.htm [25.04.
PAGE 525
Sun4/I: Memory - SIMMs SIMMs An x indicates the SIMM(s) was installed at the factory or included in a memory expansion option. An s indicates the SIMM(s) was tested and is supported in other systems.
PAGE 526
Sun4/I: Memory - SIMMs Sun-4m SIZE SPEED SIMM P/N 1MB 100ns 501-1466 1MB 100ns 501-1565 1MB 60ns 501-2289 2MB 60ns 501-2433 4MB 80ns 501-1682 4MB 80ns 501-1739 4MB 60ns 501-1991 4MB 80ns 501-2460 4MB 60ns 501-4188 8MB 60ns 501-2470 16MB 60ns 501-2059 16MB 80ns 501-2060 16MB 80ns 501-1785 16MB 80ns 501-2273 16MB 60ns 501-2479 16MB 60ns 501-4216 32MB 60ns 501-2471 32MB 60ns 501-2622 64MB 80ns 501-1930 64MB 60ns 501-2480 64MB 60ns 501-2771 4/10 4/15 4/30 SS4 SS5 SS10 SS20 SS600 Java s* s* x x s* x x x x x x
PAGE 527
Sun4/I: Memory - Sun-4/260/280 Sun-4/260/280 501-1102 501-1254 501-1451 501-1576 8MB ECC 32MB ECC 32MB ECC 16MB ECC Power 12.3 Amps @ +5Vdc 61.5 Watts 14.0 Amps @ +5Vdc 32MB 70.0 Watts 8MB http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058d.htm (1 von 3) [25.04.
PAGE 528
Sun4/I: Memory - Sun-4/260/280 Memory Board LEDs Jumper Settings Notes 1. The Sun 4200 CPU requires EPROM 3.0 or greater when more than two 16MB ECC memory boards are installed. 2. 501-1092 or 501-1117 BackpIanes: Install a single memory board in Slot 6 with a 220/270 Terminator, 120-1613-01, installed at location U1203. Remove the terminator when expansion memory boards are installed in Slots 2, 3, 4, and 5. 3.
PAGE 529
Sun4/I: Memory - Sun-4/260/280 References 1. Sun 501-1102 Memory Board Configuration Procedures, 813-2018. 2. Installation Notes for the 32MB Memory Board, 800-2123. 3. 16 MB ECC Memory Board Installation and Configuration Manual, 813-1066. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058d.htm (3 von 3) [25.04.
PAGE 530
Sun4/I: Memory - Sun-4/330 Sun-4/330 501-1723 501-1711 501-1755 501-1436 501-1317 501-1704 8MB Parity 16MB Parity 32MB Parity w 1MB SIMMS w 1MB SIMMS w 4MB SIMMS Jumper Settings JUMPER PINS SETTING DESCRIPTION J0901 1-2 In 8 SIMMS installed Out 16 SIMMS installed J0902 1-2 In 1MB SIMM Out 4MB SIMM http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058e.htm (1 von 2) [25.04.
PAGE 531
Sun4/I: Memory - Sun-4/330 Power: 1.1 Amps @ +5Vdc 5.5 Watts Note The Sun-4/330 memory uses 1MB SIMM 501-1408, 501-1466, 501-1544, 501-1565, or 501-1697, or 4MB SIMM 501-1682. Reference Sun 4300 CPU and Memory Board Configuration Procedure, 813-2064. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058e.htm (2 von 2) [25.04.
PAGE 532
Sun4/I: Memory - Sun 4300 Sun 4300 Sun-4/310/350/360/370/380/390 501-1563 501-1564 501-1495 501-1703 24MB Parity 8MB Parity 48MB Parity 32MB Parity w 1MB SIMMs w 1MB SIMMs w 1MB SIMMs w 4MB SIMMS Note Socket locations are silkscreened on the solder side of this board. http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058f.htm (1 von 3) [25.04.
PAGE 533
Sun4/I: Memory - Sun 4300 Reference 8 Mbyte, 24 Mbyte, and 48 Mbyte Parity Memory Board Installation and Configuration Manual, 800-3403. Jumper Settings and Memory Configurations JUMPER SETTING DESCRIPTION J2304 In BGR0 J2305 In BGR1 J2306 In BGR2 J2307 In BGR3 J2308 In IACK JUMPER SETTING SIMM MODULE J2309/4MEG Out 1MB SIMM J2309/4MEG In 4MB SIMM http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058f.htm (2 von 3) [25.04.
PAGE 534
Sun4/I: Memory - Sun 4300 Power 4.3 Amps @ +5Vdc 21.5 Watts 5.3 Amps @ +5Vdc 48MB 26.5 Watts 24MB Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058f.htm (3 von 3) [25.04.
PAGE 535
Sun4/I: Memory - Sun 4400 Sun 4400 Sun-4/470/490 501-1333 501-1721 32MB ECC 128MB ECC http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00590.htm (1 von 3) [25.04.
PAGE 536
Sun4/I: Memory - Sun 4400 Power 15.6 Amps @ +5Vdc 78.0 Watts 13.7 Amps @ +5Vdc 128MB 68.5 Watts 32MB LED Status and Jumper Settings Memory Board LEDs Jumper Settings JUMPER J0101 J0301 J0302 J0301 J0302 J0310 J0311 J0312 J0313 J0314 J0315 PINS SETTING DESCRIPTION 1-2 In Enable SET.
PAGE 537
Sun4/I: Memory - Sun 4400 3. SunOS 4.1 PSR A requires 4.1 PSR A Sun-4 PMEG Patch to enable over 256MB of memory. 4. A Correctable Error on the sixth 128MB board turns on the CE LED and turns off error logging. Reset power to clear this condition. Reference 32- and 128-Mbyte Memory Board Installation and Configuration Procedures, 800-3518. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00590.htm (3 von 3) [25.04.
PAGE 538
Sun4/I: Memory - Sun-4/E Sun-4/E 501-8042 4MB ECC Jumper Descriptions BOARD SIZE Sets the memory size of the board. BOARD ID Determines where a memory board is mapped into the 256MByte space allocated for memory expansion. HI/LOW MEM IN maps the memory board into the lowest 256MBytes of CPU type 0 space. OUT maps the memory board in the address range between 256MBytes and 512MBytes. http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00591.htm (1 von 2) [25.04.
PAGE 539
Sun4/I: Memory - Sun-4/E 1M/4M DRAM Specifies 1MByte or 4Mbyte DRAM modules.
PAGE 540
Sun4/I: Memory - Sun-4/E Sun-4/E 501-8036 16MB ECC Jumper Descriptions BOARD SIZE Sets the memory size of the board. BOARD ID Determines where a memory board is mapped into the 256MByte space allocated for memory expansion. HI/LOW MEM IN maps the memory board into the lowest 256MBytes of CPU type 0 space. OUT maps the memory board in the address range between 256MBytes and 512MBytes. http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00592.htm (1 von 2) [25.04.
PAGE 541
Sun4/I: Memory - Sun-4/E 1M/4M DRAM Specifies 1MByte or 4Mbyte DRAM modules.
PAGE 542
Sun4/I: Memory - Sun-4/E Combo Sun-4/E Combo 501-8060 0MB Parity JUMPER SETTING DESCRIPTION J0401 In Enable Memory Out Disable Memory Note SunOS 4.0.3e requires the 4.0.3e SRX Feature Tape to support the Combo memory card. http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00593.htm (1 von 2) [25.04.
PAGE 543
Sun4/I: Memory - Sun-4/E Combo Reference SPARCengine 1E Combo Memory Card User's Manual, 800-8152. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00593.htm (2 von 2) [25.04.
PAGE 544
Sun4/I: CPU - Contents CPU Sun-4 Architecture Sun 4100 Sun 4200 Sun 4300 Sun 4400 Sun-4e Architecture SPARCengine 1 (Sun-4/E) Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004a4.htm [25.04.
PAGE 545
Sun4/I: CPU - Sun 4100 Sun 4100 Sun 4/110/150 501-1199 501-1237 501-1462 501-1512 501-1513 501-1514 8MB w/o FP 8MB w FPC 16MB w/o FPC 501-1463 501-1464 501-1465 501-1515 501-1516 501-1517 16MB w FPC 32MB w/o FPC 32MB w FPC http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0053f.htm (1 von 6) [25.04.
PAGE 546
Sun4/I: CPU - Sun 4100 Power: with FPU 13.8 Amps @ +5Vdc 0.1 Amps @ -5Vdc 69.5 Watts Sun 4100 Sun 4/110/150 501-1656 501-1657 501-1658 8MB w/o FPC 8MB w FPC 1 6MB w/o FPC 1 501-1659 501-1660 501-1661 6MB w FPC 32MB w/o FPC 32MB w FPC http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0053f.htm (2 von 6) [25.04.
PAGE 547
Sun4/I: CPU - Sun 4100 Power: with FPU 13.8 Amps @ +5Vdc 0.1 Amps @ -5Vdc 69.5 Watts 501-1199 / 501-1237 / 501-1462 / 501-1463 / 501-1464 / 501-1465 501-1512 / 501-1513 / 501-1514 / 501-1515 / 501-1516 / 501-1517 501-1656 / 501-1657 / 501-1658 / 501-1659 / 501-1660 / 501-1661 Jumper Settings JUMPER PINS SETTING DESCRIPTION J0101 1-2 In Enable 57.
PAGE 548
Sun4/I: CPU - Sun 4100 * Default setting. The auto sense feature requires >=30 milliamps on the +12V return (example - DEC DELNI). Notes 1. The Type-4 Keyboard requires CPU >=501-1199-11 or >=501-1237-11. 2. The 501-1384 FPU2 is supported on CPU boards 501-1512, 501-1513, 501-1514, 501-1515, 501-1516, and 501-1517. 3. The final software release for the Sun 4100 is Solaris 2.4.
PAGE 549
Sun4/I: CPU - Sun 4100 Unused Pin 15-16 Out Out Out Out * Same/Different correspond to sets of 256KB or 1MB SIMMs Sun 4100 SIMM Configurations 501-1314 501-1466 256KB SIMM 1MB SIMM http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0053f.htm (5 von 6) [25.04.
PAGE 550
Sun4/I: CPU - Sun 4100 Reference Sun 4100 Board Set Configuration Procedures, 813-2049. Last updated: December 2, 1996 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0053f.htm (6 von 6) [25.04.
PAGE 551
Sun4/I: CPU - Sun 4200 Sun 4200 Sun-4/260/280 501-1274 501-1491 501-1522 w FPC-6/4 w FPU-2 w FPC-6/4 2-hi Backpanel 2-hi Backpanel Power 17.2 Amps @ +5Vdc 1.3 Amps @ -5Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00540.htm (1 von 3) [25.04.
PAGE 552
Sun4/I: CPU - Sun 4200 0.4 Amps @ +12Vdc 98.0 Watts Jumper Settings JUMPER J2701 J2003 J2201 J2902 J2404 J0304 J0303 J0302 J0301 J2801 J0401 J2001 J2002 J2401 J2402 J2403 J2404 PINS SETTING DESCRIPTION 1-2 Out Debug jumper 1-2 In Connect 3V battery 1-2 In SCC (UART)clock enable 1-2 Out Enet Level 2 (IN for level 1) 1-2 Out Null 1-2 In Enable VME clock 1-2 In 16 MHz clock enable 1-2 In 46.
PAGE 553
Sun4/I: CPU - Sun 4200 Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00540.htm (3 von 3) [25.04.
PAGE 554
Sun4/I: CPU - Sun 4300 Sun 4300 Sun-4/310/330/350/360/370/380/390 501-1316 501-1742 8MB 32MB w 1MB SIMMS w 4MB SIMMS Power 17.5 Amps @ +5vdc 0.2 Amps @ +12vdc 0.2 Amps @ -12vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00541.htm (1 von 3) [25.04.
PAGE 555
Sun4/I: CPU - Sun 4300 92.
PAGE 556
Sun4/I: CPU - Sun 4300 3. 4MB SIMMs, Option X134A, are not supported on the Sun-4/330 CPU. 4. The Sun 4100 1MB SIMM, 501-1466, may be used in the Sun-4/310 and Sun-4/350 system upgrades. 5. Fuses F0300, F3100, and F3200 use 2 Amp Fuse 150-1174-01. 6. The CPU is set for Ethernet Level 2. Level 1 is not selectable. 7. CPU >=501-1316-04 is required for use with the ISP-80 and FDDI controllers and with LISP software. 8. CPU >=501-1316-03 is required for use with CG5. 9. Boot PROM 3.
PAGE 557
Sun4/I: CPU - Sun 4400 Sun 4400 Sun-4/470/490 501-1381 501-1899 0MB 0MB Power 28.7 Amps @ +5Vdc 0.1 Amps @ +12Vdc 0.1 Amps @ -12Vdc 145.9 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00542.htm (1 von 3) [25.04.
PAGE 558
Sun4/I: CPU - Sun 4400 Jumper Settings JUMPER J0100 J0101 J0201 J0300 J0705 J1901 J2301 J2600 J2801 J2802 J2803 J2804 J3100 J3200 J3201 J3203 J3603 J3604 J3701 J3703 J3703 J4000 J4600 J4602 J4604 J4605 J4606 J4607 J4608 J4609 PINS SETTING DESCRIPTION 1-10 Out Used for debug 1-2 In Used for ATE 1-2 In Used for ATE 1-2 In If FPC is present 3-4 Out If FPC is present 5-6 In Avoid a trap when I-Flush instruction is executed 7-8 Out FPC Chaining (only if FPC is present) 1-10 Out Used for debug 1-36 Out Used f
PAGE 559
Sun4/I: CPU - Sun 4400 Notes 1. Install Fused Shunt 150-1669-01 at locations J3603 and J3604 to provide circuit protection to the M+ (+12Vdc) and M- (-12Vdc) inputs to the UC5170 Serial Port Line Driver. 2. The output of Pin-25 from the Serial Port on the 501-1381 CPU is -5Vdc. There is no output from Pin-25 on the 501-1899 CPU. 3. The 501-1381 CPU is not supported in Sun-4/470 serial numbers 136Kxxxx and greater. This chassis has two 50-pin SCSI-2 connectors on the rear EMI cover. 4. SNC 1.
PAGE 560
Sun4/I: CPU - SPARCengine 1 (Sun-4/E) SPARCengine 1 (Sun-4/E) 501-8035 501-8058 501-8064 4MB w Weitek 4MB w/o Weitek 16MB w Weitek Power 5.0 Amps @ +5Vdc 0.1 Amps @ +12Vdc 0.1 Amps @ -12Vdc 27.4 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00543.htm (1 von 2) [25.04.
PAGE 561
Sun4/I: CPU - SPARCengine 1 (Sun-4/E) Jumper Settings JUMPER PINS SETTING DESCRIPTION J0301 1-2 In 20MHz clock enable J0801 1-2 In Use 4MB parity memory (default) 2-3 In Disable 4MB parity memory J1701 1-2 In CPU is installed in VME slot 1 Notes 1. 2. 3. 4. 5. Boot PROM 1.4 does not support SunOS 4.1e. Boot PROM 1.5 supports SunOS 4.1e. Boot PROM 1.6 supports SunOS 4.1e. Boot PROM 1.6 and EPROM daughter card 500-8013-05 are installed on CPU 501-8035-12.
PAGE 562
Sun4/I: Configurations Configurations Sun PROM Monitor Commands Configurations Handling Static Sensitive Devices Electronic components on printed circuit boards can be damaged by static electricity. Always wear a grounding strap and use an antistatic mat when handling boards or components.
PAGE 563
Sun4/I: Configurations Jumpers Jumpers are used to connect two pins of a Terminal Strip. Two sizes of jumpers are used: 0.100 inch and 2.0 millimeter. Sun PROM Monitor Commands To program the EEPROM or NVRAM using the Sun PROM Monitor, enter q followed by the hexadecimal address in the EEPROM or NVRAM to open and display the contents. Change the contents by typing in the new value followed by a carriage return. To exit, type a space and , or a "." and . http://lios.apana.org.
PAGE 564
Sun4/I: Configurations Common EEPROM or NVRAM Parameters Location 0x14 [Installed Memory] Amount of installed Memory in hexadecimal Location 0x15 [Tested Memory] Amount of memory to test during Power On Self-Test Location 0x16 [Monitor Screen Size] 00 = 1152x900 (standard resolution) 12 = 1024x1024 (1Kx1K) 13 = 1600x1280 (high resolution) (see 0x50 & 0x51) 14 = 1440x1440 15 = 1024x768 (low resolution) Location 0x17 [Watchdog Reset Action] 00 = Watchdog Reset returns to the PROM monitor 12 = Watchdog Reset
PAGE 565
Sun4/I: Configurations Location 0x21 [Keyboard Click] 00 = turns keyboard click OFF 12 = turns keyboard click ON (default) Location 0x22 - 0x23 [Diagnostic Boot Device in ASCII] xy xd sd ie id gn le 78 78 73 69 69 67 6c 79 64 64 65 64 6e 65 Location 0x24, 0x25, and 0x26 [Controller, Unit, Partition] 00 00 00 (default) Location 0x28 - 0x4f [Diagnostic Boot Path] These 40 bytes represent the ASCII values for the desired diagnostic boot path.
PAGE 566
Sun4/I: Configurations 4800 baud 12 c0 9600 baud 25 80 Location 0x63 [Serial Port B DTR/RTS] 00 = asserts DTR and RTS signals 02 = does not assert DTR and RTS signals Location 0x18f [LogoType] 00 = Sun 06 = 3D for CG6 12 = Custom Location 0x492 [Password Mode Select] Sun-3 and Sun-4 Boot PROM >= 2.7.1 5E = fully secure mode 01 = command secure mode All else = non-secure mode Location 0x493-0x49a [Password Bytes] Sun-3 and Sun-4 Boot PROM >= 2.7.1 8 bytes of password in ASCII If the PROM Rev level is 2.