HP StorageWorks SN6000 Fibre Channel Switch Installation and Reference Guide Part Number: 5697-0260 Published February 2010 Edition: 1
Legal and notice information © Copyright 2010 Hewlett-Packard Development Company, L.P. © Copyright 2010. This software includes technology under a license from QLogic Corporation. All rights reserved. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Contents About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . Document conventions and symbols . . . . . . . . . . . . . . . . . . Rack stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HP technical support . . . . . . . . . . . . . . . . . . . . . . . .
IP security . . . . . . . . Port binding . . . . . . Connection security . Device security . . . . Fabric management . . . .. .. .. .. .. . . . . . .. .. .. .. .. .. .. .. .. .. . . . . . .. .. .. .. .. .. .. .. .. .. . . . . . .. .. .. .. .. . . . . . .. .. .. .. .. .. .. .. .. .. . . . . . .. .. .. .. .. .. .. .. .. .. . . . . . .. .. .. .. .. . . . . . .. .. .. .. .. .. .. .. .. .. . . . . . .. .. .. .. .. .. .. .. .. .. . . . . . .. .. .. .. .. . . . . . .. .. .. .. .. .. ..
Exiting the maintenance menu (option 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking a firmware image file in maintenance mode (option 1). . . . . . . . . . . . . . . . . . . . . . . . . . . Resetting the network configuration in maintenance mode (option 2) . . . . . . . . . . . . . . . . . . . . . . . . . Resetting user accounts in maintenance mode (option 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Tables 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 6 SN6000 Fibre Channel Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switch LEDs and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fibre Channel ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this guide This guide provides information about: • Becoming acquainted with the switch features and capabilities • Planning a fabric including devices, device access, performance, multiple switch fabrics, switch services, fabric security, and fabric management. • Installing and configuring an HP StorageWorks SN6000 Fibre Channel Switch • Diagnosing and troubleshooting switch problems Intended audience This manual introduces users to the switch and explains its installation and service.
Document conventions and symbols Document conventions Table 1 Convention Element Medium blue text: Figure 1 Cross-reference links and e-mail addresses Medium blue, underlined text (http://www.hp.
Rack stability WARNING! To reduce the risk of personal injury or damage to equipment: • Extend leveling jacks to the floor. • Ensure that the full weight of the rack rests on the leveling jacks. • Install stabilizing feet on the rack. • In multiple-rack installations, secure racks together. • Extend only one rack component at a time. Racks may become unstable if more than one component is extended.
HP websites For other product information, see the following HP websites: • http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/support/ • http://www.docs.hp.com Documentation feedback HP welcomes your feedback. To make comments and suggestions about product documentation, please send a message to storagedocs.feedback@hp.com. All submissions become the property of HP.
1 General description The HP StorageWorks SN6000 Fibre Channel Switch (Figure 1) is a 24 port, 8 Gb/s switch with both Ethernet and serial management interfaces.
Switch LEDs and controls The switch LEDs provide information about the switch’s operational status. These LEDS include the Input Power LED (green), Heartbeat LED (green), and the System Fault LED (amber) (Figure 2). For information about port LEDs, see ”Port LEDs” on page 15. The Maintenance button (Figure 2) is the only switch control. It is used to reset a switch or to recover a disabled switch.
Maintenance button The Maintenance button (Figure 2) is a dual-function momentary switch on the front panel. Its purpose is to reset the switch or to place the switch in maintenance mode. Maintenance mode sets the IP address to 10.0.0.1 and provides access to the switch for maintenance purposes when flash memory or the resident configuration file is corrupted. For more information, see ”Recovering a switch using maintenance mode” on page 57.
Fibre Channel ports The HP StorageWorks SN6000 Fibre Channel Switch has 20 Fibre Channel Small Form-Factor Pluggable (SFP) ports and four Fibre Channel XPAK ports. SFP ports are numbered 0–19 (Figure 3). Each SFP port is served by an SFP optical transceiver and is capable of 1, 2, 4, or 8 Gb/s transmission. SFP ports are hot-pluggable and can self-discover both the port type and transmission speed when connected to devices or other switches.
Port LEDs Each port has its own Logged-in LED (green) and Activity LED (green) (Figure 4). 1 2 3 4 1 Logged-in LED (port 9) 2 Activity LED (port 9) 3 Activity LED (port 23) 4 Logged-in LED (port 23) Figure 4 Port LEDs Port Logged-in LED (green) The Logged-in LED indicates the logged-in or initialization status of the connected devices. After successful completion of the POST, the switch extinguishes all Logged-in LEDs.
SFP ports configured as GL_Ports and all XPAK ports configured as G_Ports. Table 2 describes generic, fabric, expansion, and transparent routing port functions. Table 2 16 Fibre Channel port types Port type Description GL_Port Generic loop port—self-configures as an FL_Port when connected to a loop device, as an F_Port when connected to a single device, or as an E_Port when connected to another switch.
Ethernet port The Ethernet port is an RJ-45 connector that provides a connection to a workstation through a 10/100 Base-T Ethernet cable (Figure 5). A workstation can be a Windows or a Linux server that is used to configure and manage the switch fabric. An Ethernet connection to the switch is required to manage the switch using the CLI, QuickTools, Simple SAN Connection Manager, or Simple Network Management Protocol (SNMP).
The serial port connector requires a null-modem F/F DB9 cable. The pins on the switch RS-232 connector (Figure 6) are identified in Table 3. For information about connecting the workstation through the serial port, see ”Connect the management station or workstation to the switch” on page 41.
Each power supply is capable of providing all of the switch’s power needs. During normal operation, each power supply provides half of the demand. If one power supply goes offline, the second power supply steps up and provides the difference. The power supplies are hot-pluggable and interchangeable. Hot-pluggable means that you can remove and replace one power supply while the switch is in operation without disrupting service.
Simple Network Management Protocol SNMP provides monitoring and trap functions for the fabric. The switch firmware supports SNMP versions 1, 2, and 3, the Fibre Alliance Management Information Base (FA-MIB) version 4.0, and the Fabric Element Management Information Base (FE-MIB) RFC 2837. Traps can be formatted using SNMP version 1 or 2. SNMP version 3 provides secure access to devices through a combination of authentication and encryption.
2 Planning Consider the following when planning a fabric: • Devices, page 21 • Device access, page 21 • Performance, page 22 • Feature licenses, page 23 • Multiple switch fabrics, page 23 • Switch services, page 28 • Security, page 30 • Fabric management, page 32 Devices When planning a fabric, consider the following: • The number of devices and the anticipated demand. This will determine the number of ports that are needed and in turn the number of switches.
A zoning database is maintained on each switch. Table 4 describes the zoning database limits, excluding the active zone set. Table 4 Zoning database limits Limit Description MaxZoneSets Maximum number of zone sets (256). MaxZones Maximum number of zones (2,000). MaxAliases Maximum number of aliases (2,500). MaxTotalMembers Maximum number of zone and alias members (10,000) that can be stored in the zoning database. Each instance of a zone member or alias member counts toward this maximum.
Latency Latency is a measure of how fast a frame travels through a switch from one port to another. The factors that affect latency include transmission rate and the source/destination port relationship (Table 5). Table 5 Port-to-port latency Destination Rate Source Rate 1 Gb/s 2 4 8 10 20 2 < 0.6 μsec < 0.7 μsec1 < 0.6 μsec1 < 0.6 μsec1 < 0.6 μsec1 4 < 0.4 μsec < 0.3 μsec < 0.4 μsec1 < 0.4 μsec1 < 0.3 μsec1 8 < 0.3 μsec < 0.2 μsec < 0.2 μsec < 0.2 μsec1 < 0.2 μsec1 10 < 0.
Domain ID, principal priority, and domain ID lock The following switch configuration settings affect multiple switch fabrics: • Domain ID • Principal priority • Domain ID lock The domain ID is a unique number from 1–239 that identifies each switch in a fabric. The principal priority is a number (1–255) that determines the principal switch which manages domain ID assignments for the fabric. The switch with the highest principal priority (1 is high, 255 is low) becomes the principal switch.
Figure 9 shows a three-switch stack of HP StorageWorks SN6000 Fibre Channel Switch switches using two 3-inch and one 9-inch XPAK switch stacking cables. 60 SFP ports are available for devices. Figure 9 Three-switch stack Figure 10 shows a four-switch stack of model SN6000 switches using three 3-inch and three 9-inch XPAK switch stacking cables. 80 SFP ports are available for devices.
Figure 12 shows a six-switch stack of model SN6000 switches using eight XPAK switch stacking cables. 120 SFP ports are available for devices. Figure 12 Six-switch stack Common topologies Although HP recommends using the XPAK stacking ports to achieve the highest cabling efficiency and bandwidth, you can also create multiple switch configurations using the SFP ports.
You can connect multiple SN6000 Fibre Channel Switches to one or more remote fabrics using multiple TR_Ports. Local and remote devices are identified by their respective port worldwide names. Consider the following mapping rules: • A TR_Port can support a maximum of 32 local device/remote device mappings. • A specific local device can be mapped to devices on only one remote fabric. Local devices on the same SN6000 Fibre Channel Switch can each be mapped to different remote fabrics.
3. Map local devices to remote devices and activate the connection. The QuickTools mapping process creates an inter-fabric zone (IFZ) in the active zone set consisting of the local device, the remote device, and the TR_Port. When the mapping is complete, QuickTools activates the new zone set. The name of the inter-fabric zone begins with IFZ followed by the lowest device port WWN followed by the remaining port WWN, all uppercase, separated by underscores (_).
• Call Home: IMPORTANT: The Call Home service provides an e-mail notification capability for the switch. This service has no relationship with the HP Call Home feature, which notifies only HP services. Provides for automated e-mail notification of switch status and operating conditions based on specified event severity levels. The default is enabled. The Call Home service requires an Ethernet connection to at least one Simple Mail Transfer Protocol (SMTP) server.
Security Security is available at the following levels: • User account security, page 30 • IP security, page 30 • Port binding, page 30 • Connection security, page 30 • Device security, page 31 User account security User account security consists of the administration of account names, passwords, expiration date, and authority level. If an account has Admin authority, all management tasks can be performed by that account in the CLI, QuickTools, and Simple SAN Connection Manager.
The SSL handshake process between the workstation and the switch involves the exchanging of certificates. These certificates contain the public and private keys that define the encryption. When the SSL service is enabled, a certificate is automatically created on the switch. The workstation validates the switch certificate by comparing the workstation date and time to the switch certificate creation date and time.
Fabric management The Simple SAN Connection Manager application is a GUI-based management application for HP StorageWorks that runs on the management station. It provides basic automated configuration and management of switches, HBAs, and storage devices. Switch management functions include IP address configuration and limited control of zoning. Simple SAN Connection Manager version 3.0 or later is required for the HP SN6000 Fibre Channel Switch.
3 Installation This section describes how to install and configure the switch.
Table 7 Workstation requirements for QuickTools Operating systems Windows 2003 and XP SP1/SP2 Red Hat Enterprise Linux 4, 5 SUSE Linux Enterprise Server 9 and 10 Memory 512 MB Processor 2 GHz or faster Internet Browser Microsoft Internet Explorer 6.0 or later Netscape Navigator 6.0 and later Mozilla 1.5 and later Firefox 1.5 and later Java Runtime Environment 1.4.2 or later1 Hardware RJ-45 Ethernet port 1.
Installing a SN6000 Fibre Channel Switch involves the following steps: 1. Mount the switch, page 35 2. Install the transceivers, page 39 3. Configure the workstation, page 39 4. Apply power to the switch, page 40 5. Connect the management station or workstation to the switch, page 41 6. Configure the switch, page 41 7. Cable devices to the switch, page 42 Mount the switch The switch can be placed on a flat surface and stacked, or mounted in a 19” Electronics Industries Association (EIA) rack.
Collect the required items NOTE: The rack mount kit installation requires one technician. Locate the following items and set them aside: • SN6000 Fibre Channel Switch • 8/20q and SN6000 Fibre Channel Switch rack-mount kit • Smaller items, such as screws, ship in plastic bags in the kit. See Table 8.
Rack the switch 1. Remove and discard the four 10-32 screws from the sides of the switch. 2. Attach each rail to the switch using two 10-32 x .375-inch screws with captive washers (Figure 13). Make sure the slotted ends of the rails are on the power-supply side (not the SFP-port side) of the switch. Figure 13 Attaching the rails to the switch 3. On the rack vertical posts, mark the holes that will be used by the rail flanges (three on each rear vertical post, two on each front vertical post).
5. Fasten each rail flange to the front of the rack using two M6 machine screws (Figure 16). Figure 16 Fastening the rail to the front of the rack 6. Fasten each slotted-rail end to the rear mounting bracket using a flat washer and a 1/4-20 hex nut (Figure 17). Figure 17 Fastening the rail to the rear mounting bracket 7. Optional: Fasten the filler panel to the rear mounting brackets with two M6 machine screws (Figure 18).
Install the transceivers A small form-factor pluggable (SFP) transceiver is required for each switch port connected to a device or another switch. SFPs are not included with the switch. An XPAK transceiver is required for each switch 10 Gb/s port connected to the 10 Gb/s port of another switch. Only HP transceivers are supported for use in the switch. To install an transceiver, insert the transceiver into any of the active switch ports and gently press until it snaps in place.
For a Linux workstation: a. Set up minicom to use the serial port. Create or modify the /etc/minirc.dfl file with the following content. pr pu pu pu portdev/ttyS0 minit mreset mhangup b. Verify that all users have permission to run minicom. Review the /etc/minicom.users file and confirm that the line ALL exists or that there are specific user entries. Apply power to the switch WARNING! This product is supplied with a 3-wire power cable and plug for the user’s safety.
Connect the management station or workstation to the switch You can manage the switch using the Simple SAN Connection Manager, QuickTools, or the CLI. Simple SAN Connection Manager requires at least one FC connection and an Ethernet connection to the switch. QuickTools requires an Ethernet connection to the switch. The CLI can use an Ethernet connection or a serial connection. • If this switch is part of the 8Gb Simple SAN Connectivity Kit installation: a.
QuickTools switch configuration To log in and configure the switch using QuickTools: 1. Open an Internet browser and enter the default IP address 10.0.0.1 to start the QuickTools web applet. 2. Log in to the switch using the default user name (admin) and password (password). 3. Obtain the IP address and subnet mask from your network administrator. 4. Open the QuickTools Wizards menu and select Configuration Wizard. Follow the instructions to set the IP address and the password.
Installing firmware The switch comes with current firmware installed. You can upgrade the firmware from the management station or workstation as new firmware becomes available using Simple SAN Connection Manager, QuickTools, or the CLI. This guide describes the use of QuickTools and the CLI. For information about installing firmware using Simple SAN Connection Manager, see the HP StorageWorks Simple SAN Connection Manager User Guide.
Using the CLI to install firmware The method you choose to install firmware using the CLI depends on the type of firmware activation you want. • For a disruptive activation, enter the firmware install or image install command to download the firmware image file from an FTP or TFTP server, unpack it, and activate it in one step. See ”One-step firmware installation” on page 44. • For a non-disruptive activation, enter the image fetch command to download the firmware image file from an FTP or TFTP server.
5. Enter the password for your account name (FTP only). 331 Password required for johndoe. Password:****** 230 User johndoe logged in. The firmware will now be downloaded from the remote host to the switch, installed, and activated. Custom firmware installation A custom firmware installation downloads the firmware image file from an FTP or TFTP server to the switch, unpacks the image file, and resets the switch in separate steps.
4. Configure the port types for the new switch. The ports can be G_Port, GL_Port, F_Port, FL_Port, TR_Port, or Donor. 5. Connect the devices to the switch. 6. Make any necessary zoning changes. Installing feature license keys For information about available license keys, see ”Feature licenses” on page 23. To install a license key using QuickTools: 1. Open the Switch Menu and select Features to open the Feature Licenses dialog. 2. In the Feature Licenses dialog, click Add to open the Add License Key dialog.
Installation instructions and documentation for SIM, RSP, OSEM, and ISEE Software, installation instructions, release notes, and other documentation for SIM, RSP, OSEM, and ISEE Standard Configuration are available at no charge from the following HP websites: • For SIM at http: //www.hp.com/go/hpsim • For RSP at http://www.hp.com/go/ServiceEssentials • For OSEM at http://h18023.www1.hp.com/support/svctools/OSEM/index.html • For ISEE at http://www.hp.com/hps/tech/resources/elect/isee.
Infrastructure requirements for implementing Call Home to HP Services To implement Call Home to HP Services, the following infrastructure requirements must be met: • Internet access to the Central Management Server running RSC, or a server running ISEE. (Required because notification messages are sent by RSC or ISEE to HP over the Internet.) • OSEM can run on the same server as RSC or ISEE or on a server that has LAN access to the server running RSC or ISEE.
The following example configures SNMP trap 1: SN6000 FC Switch #> admin start SN6000 FC Switch (admin) #> set setup snmp trap 1 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so. Current Values: Trap1Enabled Trap1Address Trap1Port Trap1Severity Trap1Version Trap1Community False 10.0.0.
4 Diagnostics and troubleshooting Diagnostic information about the switch is available through the switch LEDs and the port LEDs. Diagnostic information is also available through the CLI, QuickTools, or Simple SAN Connection Manager event logs and error displays. This section describes the following types of diagnostics: • Switch diagnostics, page 51 describes the Input Power LED and System Fault LED indications.
System fault LED is illuminated The System Fault LED illuminates to indicate that a fault exists in the switch firmware or hardware. If the System Fault LED illuminates, identify the Heartbeat LED error blink pattern and take the necessary actions. See ”Heartbeat LED blink patterns” on page 52. Power-On self test diagnostics The switch performs a series of tests as part of its power-up procedure.
Fatal POST error blink pattern A system error blink pattern is 3 blinks followed by a 2-second pause. The 3-blink error pattern indicates that a POST failure or a system error has left the switch inoperable. If a system error occurs, contact your authorized maintenance provider. Momentarily press and release the Maintenance button to reset the switch. 2 seconds Configuration file system error blink pattern A configuration file system error blink pattern is 4 blinks followed by a 2-second pause.
Logged-in LED indications Port diagnostics are indicated by the Logged-in LED for each port (Figure 21). 1 2 1 Logged-in LED (port 0) 2 Logged-in LED (port 10) Figure 21 Logged-in LED The Logged-in LED has three indications: • Continuous illumination: A device is logged in to the port. • Flashing once per second: A device is logging in to the port, or the port is in the diagnostics state. • Flashing twice per second: The port is down, offline, or an error has occurred.
3. Display the fabric domain IDs using the show domains CLI command or by selecting the QuickTools Switch tab, Summary icon. Are all domain IDs in the fabric unique? • Yes—Continue. • No—Correct the domain IDs on the offending switches using the set config switch CLI command or the QuickTools Switch Properties dialog. Reset the port. If the condition remains, continue. 4.
Review the event browser to determine if excessive port errors are responsible for disabling the port. Look for a message that mentions one of the monitored error types indicating that the port has been disabled, then perform the following procedure: 1. Examine the alarm configuration for the associated error using the show config threshold CLI command. See the show config threshold CLI command in the HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide.
• All power supply LEDs are normal, yet the System Fault LED is illuminated and the Heartbeat LED does not show a blink pattern. This means that the two power supplies have different air flow directions. Replace the power supply with the incorrect air flow direction with a power supply that has the correct air flow direction. Air flow direction is marked on the power supply part number label. See ”Power Supply Removal and Replacement” on page 61. • Power Supply Fault LED is illuminated.
Exiting the maintenance menu (option 0) The Exit option closes the current Maintenance menu session. To log in again, enter the maintenance mode account name (prom) and password (prom). To return to normal operation, momentarily press and release the Maintenance button or power cycle the switch. Unpacking a firmware image file in maintenance mode (option 1) The Image Unpack option unpacks and installs new firmware when the current firmware has become corrupt.
NOTE: If you choose the Remake Filesystem option, you will lose all changes made to the fabric configuration that involve that switch, such as password and zoning changes. You must then restore the switch from an archived configuration or reconfigure the portions of the fabric that involve the switch. Resetting the switch in maintenance mode (option 7) The Reset Switch option closes the Telnet session, exits maintenance mode, and reboots the switch using the current switch configuration.
5 Removal/Replacement This section describes the removal and replacement procedures for the following field replaceable units (FRU): • SFP and XPAK transceivers • Power supplies for the SN6000 Single Supply Switch and the SN6000 Dual Supply Switch models • The switch is equipped with a battery that powers the non-volatile memory. This memory stores the switch configuration. The battery is not a field replaceable unit. WARNING! The battery may explode if replaced incorrectly.
NOTE: Both power supplies must have the same air flow direction to prevent the switch from overheating. To avoid overheating, do not operate the switch with one power supply any longer than necessary. When removing or replacing a power supply, consider the following: • The left and right power supplies are interchangeable. However, you must orient the power supply so that AC receptacle is on the right. • Both power supplies must have the same air flow direction.
4. Plug the power cord into the AC receptacle. Confirm that air flow direction is correct. 1 1 Air flow label 2 2 AC receptacle Figure 24 Power Supply Installation The power supply in the SN6000 Single Power Supply Fibre Channel Switch can be removed and replaced, but as there is only one power supply, it is not hot-pluggable. To remove the power supply: 1. Unplug the power cord from the power supply. 2.
A Regulatory compliance and safety Regulatory compliance Federal Communications Commission notice for Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Certification and classification information This product contains a laser internal to the fiber optic (FO) transceiver for connection to the Fibre Channel communications port. In the USA, the FO transceiver is certified as a Class 1 laser product conforming to the requirements contained in the Department of Health and Human Services (DHHS) regulation 21 CFR, Subchapter J. A label on the plastic FO transceiver housing indicates the certification.
European Union regulatory notice This product complies with the following Eurupean Union (EU) directives: • Low Voltage Directive 2006/95/EC • EMC Directive 2004/108/EC Compliance with these directives implies conformity to applicable harmonized European standards (European norms), which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for this product or product family.
B Electrostatic discharge This appendix provides the following information: • How to prevent electrostatic discharge, page 69 • Grounding methods, page 69 How to prevent electrostatic discharge To prevent damage to the system, you must follow certain precautions when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
C Technical specifications This appendix contains the specifications for the SN6000 Fibre Channel Switch. See ”General description” on page 11 for the location of all connections, switches, controls, and components.
Table 9 General specifications (Continued) Specification Description Scalability Maximum 239 switches, depending on configuration. For the latest supported configurations, see the SAN Design Reference Guide available at http://www.hp.com/go/SANdesignguide. Maximum user ports > 475,000 ports depending on configuration. For the latest supported configurations, see the SAN Design Reference Guide available at http://www.hp.com/go/SANdesignguide.
Maintainability features Table 10 lists maintainability features for the SN6000 Fibre Channel Switch. Table 10 Maintainability features Specification Description Diagnostics The POST tests all functional components except SFP transceivers. Port tests include online, internal, and external tests. User interface LED indicators Field replaceable units (FRUs) Power supply Fabric management specifications Table 11 lists fabric management specifications for the SN6000 Fibre Channel Switch.
Weight and physical dimensions Table 12 lists physical properties for the SN6000 Fibre Channel Switch. Table 12 Switch physical dimensions Property Value Height 1U or 43.2 mm (1.70 in) Width 432 mm (17 in) Depth 500 mm (19.7 in) Weight Dual power supply: 8.16 kg (18 lbs.) Single power supply: 6.8 kg (15 lbs.) Electrical specifications Table 13 lists electrical specifications for the SN6000 Fibre Channel Switch.
D Factory configuration defaults This appendix describes the following factory configuration defaults: • Factory switch configuration, page 75 • Factory port configuration, page 76 • Factory port threshold alarm configuration, page 77 • Factory zoning configuration, page 77 • Factory SNMP configuration, page 78 • Factory switch services configuration, page 78 • Factory DNS host name configuration, page 79 • Factory IP version 4 Ethernet configuration, page 79 • Factory IP version 6 Ethernet configuration,
Factory port configuration Enter the show config port CLI command to display port configuration values.
Factory port threshold alarm configuration Enter show config threshold CLI command to display threshold alarm configuration values. If the ThresholdMonitoringEnabled parameter is disabled (False), none of the individual threshold monitoring parameter settings can be applied.
Factory SNMP configuration Enter the show setup snmp CLI command to display SNMP configuration values.
Table 20 Services configuration defaults Parameter Default SNMPEnabled True NTPEnabled False CIMEnabled True FTPEnabled True MgmtServerEnabled True CallHomeEnabled True Factory DNS host name configuration Enter the show setup system dns CLI command to display the Domain Name System host name configuration values.
Factory IP version 6 Ethernet configuration Enter the show setup system ipv6 CLI command to display the IP version 6 Ethernet configuration values. Table 23 IP version 6 Ethernet configuration defaults Parameter Default EthIPv6NetworkEnable True EthIPv6NetworkDiscovery Ndp EthIPv6NetworkAddress ::/64 EthIPv6GatewayAddress :: Factory event logging configuration Enter the show setup system logging CLI command to display the event logging configuration values.
Factory RADIUS configuration Enter the show setup radius CLI command to display RADIUS configuration values. Table 27 RADIUS configuration defaults Parameter Default DeviceAuthOrder Local UserAuthOrder Local TotalServers 0 DeviceAuthServer False UserAuthServer False AccountingServer False ServerIPAddress 10.0.0.
Factory Call Home configuration Enter the show setup callhome CLI command to display call home configuration values. Table 29 82 Call Home service configuration defaults Parameters Default PrimarySMTPServerAddr 0.0.0.0 PrimarySMTPServerPort 25 PrimarySMTPServerEnabled False SecondarySMTPServerAddr 0.0.0.0 SecondarySMTPServerPort 25 SecondarySMTPServerEnabled False ContactEmailAddress nobody@localhost.
Glossary This glossary defines terms used in this guide or related to this product. It is not a comprehensive glossary of computer terms. Active firmware The firmware image on the switch that is in use. Active zone set The zone set that defines the current zoning for the fabric. See Zone set. Activity LED A port LED that indicates when frames are entering or leaving the port. Administrative state Assigned state that determines the operational state of the port or switch.
Fabric services A component of fabric security that provides for the control of inband management and SNMP on a switch. See Fabric security and Simple Network Management Protocol (SNMP). FC port Fibre Channel port FL_Port Fabric loop port. A Fibre Channel switch port that supports a connection to up to 126 server or storage devices. Flash memory Memory on the switch that contains the switch control firmware.
Principal switch The switch in the fabric that manages domain ID assignments. See Domain ID. QuickTools A browser-based switch management application that resides in the switch firmware. Remote Authentication Dial-in Service (RADIUS) A service that supports the remote authentication of user and device logins to a switch. Secure shell (SSH) A protocol that secures connections to the switch for the command line interface.
Index Numerics 10/100 Base-T straight cable 41 A account name default 42 FTP 45 maintenance mode 57 active zone set 21 Activity LED 15, 17 air flow 72 alias 21 altitude 74 authorization 31 B bandwidth 22, 72 boot loader 59 browser 33, 34 buffer credit 22, 72 C cable 10/100 Base-T 41 10/100 Base-T crossover 41 null modem F/F DB9 41 Call Home service configure to HP service 46 description 29 certificate 31 classes of service 71 command line interface 19 Common Information Model 28 configuration file system
flash memory 13 four-switch stacking 25 frame size 72 FRU - See Field Replaceable Unit FTP - See File Transfer Protocol G G_Port 16 generic ports 15 GL_Port 16 H hardware requirements 33, 34 HBA - See Host Bus Adapter Heartbeat LED 12, 52 heat output 74 help, obtaining 9, 10 HP services 46 storage website 10 Subscriber’s choice website 9 technical support 9 humidity 34, 74 HyperTerminal application 39 I inband management 28 Input Power LED 51 installation 34 Inter-Fabric Zone 28 internal firmware failure
fatal error 53 principal priority 24 switch 24 processor 33, 34, 72 Q QuickTools service 28 web applet 19 R rack mount 35 rack stability, warning 9 RADIUS - See Remote Dial-In User Service.
X XPAK port 14 Z zone conflict 55 definition 21 zone set active 21 definition 21 zoning database 22 hardware-enforced 21 limits 22 90
