User guide

ManualsBrandsHoyles ManualsSensorsCig-Arrete Radio Com'd Flame/ Smoke Detector c/w Voice Alarm

WIRING CONNECTIONS

If you are using a power supply, then decide which product

will be the Master Unit of the system and connect a 6Vdc

power supply as shown opposite. This connection is continued

through to every device on the system to supply power. This

will normally be the CSA‐FSU installed outside the washroom

area. You can connect up to 10 devices to the CSA‐FSU as

shown in the diagram opposite.

When any device generates an alarm condition, this will be

relayed to the Master Unit which will also generate an alarm

condition simultaneously. You can use any of the devices as a

Master Unit, the diagram opposite is by way of example only.

Use 7 x 0.2mm stranded alarm cable for all the connections.

Once the wiring is complete and checked, switch on the

power supply at the mains. Each device will provide a mes‐

sage stating how it is configured. If you have a gas (smoke)

element, the device will flash its LED for 2 minutes to normal‐

ise.

DO NOT TEST THE DEVICE UNTIL THE FLASHING STOPS. Your system is now installed and running normally.

SpeechPOD (Part No CSA‐POD) is normally supplied

with an on‐board infra red PIR motion sensor as its

detection device.

You can however trigger the SpeechPOD by other

sources instead or in addition to the PIR motion

sensor. Examples of these may be:

Door Contact, Pressure mat, alarm output from

security, fire or Building Management Systems, or

any other device that has a Clean or Volt Free

Output.

Simply connect the Normally Open (NO) contact across the TRIG IN and GND input. Each time the switch closes, Speech‐

POD will play its programmed message. Remember, SpeechPOD can be battery operated or powered from a 6Vdc power

supply connected to the +6V IN and GND inputs.

For further information or assistance with our products, please contact our Technical Department by phone or email as

detailed below.

PRODUCT INSTALLATION GUIDE

FOR THE FOLLOWING PRODUCTS

Part No: CSA‐POD

Advanced SpeechPOD

Voice Warning System

Part No: CSA‐FGS

Cig‐Arrête® Combined Flame,

Smoke and SpeechPOD

Part No: CSA‐FSV

Cig‐Arrête® Combined

Flame and SpeechPOD

Part No: CSA‐FSU

Cig‐Arrête® Combined

Flasher & Sounder Unit

Part No: CSA‐FGV

Cig‐Arrête® Combined

Flame & Smoke Detector

Part No: CSA‐FOV

Cig‐Arrête® Flame Detector

With Voice Sounder

Part No: CSA‐GOV

Cig‐Arrête® Smoke Detector

With Voice Sounder

Part No: CSA‐GSV

Cig‐Arrête® Combined

Smoke & SpeechPOD

Part No: CSA‐DUAL

Advanced SpeechPOD Dual

Voice Warning System

Summary of content (4 pages)

PAGE 1
PRODUCT INSTALLATION GUIDE WIRING CONNECTIONS If you are using a power supply, then decide which product will be the Master Unit of the system and connect a 6Vdc power supply as shown opposite. This connection is continued through to every device on the system to supply power. This will normally be the CSA‐FSU installed outside the washroom area. You can connect up to 10 devices to the CSA‐FSU as shown in the diagram opposite.
PAGE 2
GENERAL OVERVIEW OF PRODUCTS Congratulations on your purchase of the most advanced smoking detection system and voice warning system available on the market today. All the Cig‐Arrête and SpeechPOD products are compatible with any PC running Windows® Operating System using ‘Drag and Drop’ file programming. In this installation guide, we will take you through the various programming options and also how to connect your products together to form a system.
PAGE 3
SPEECHPOD CONFIGURATION AND SETUP PROCEEDURE Once you have accessed the configuration menu by pressing the SpeechPOD button, you have access to all the functions relevant to the SpeechPOD element.. All these functions are shown below, but remember if you do not have a particular element (e.g. PIR Motion sensor) on the device you have purchased, you will not be able to set the configuration menu for this element.
PAGE 4
GENERAL OPERATING PROCEEDURE All our products whether Cig‐Arrête® or SpeechPOD can only be operated by use of the CSA‐IR2 Infra Red remote Control handset. The products have a number of advanced features to allow the facility management team to change messages, flame and smoke sensitivity, volume and timer functions when necessary.