User Manual

Model 28 Fing Instrucons
6. Posion the Understrap [f] centrally on the seat cushion
7. If the passenger is under 135cm place a Booster Seat or Cushion on top of the Understap to comply with child seat safety
legislaon (See back of Instrucons for further informaon)
8. Posion the Back Pad & Body Harness on the seat so that the waist belt will be in line with the waist when the passenger sits down.
9. With the harness unfastened at the waist belt sit the passenger on the understrap / child seat in the most upright posion as
possible & bring their arms through the shoulder straps [d].
8. Now bring the understrap [f] up between the legs and loop it back onto the waist belt over the buckle [h].
9. Connect the waist belt buckle to fasten the harness. Posion the buckle centrally at waist level on the passenger.
10. Adjust all straps to t ghtly yet comfortably by pulling the tail-ends of strapping through the Adjuster Buckles [i].
11. If using the Houdini Stop Chest Strap [j], aach to Shoulder Straps underneath the Adjuster Buckles [j]. See instrucon provided.
12. Ensure that the three Comfort Pads [g] are in posion over the Adjuster Buckles [i] on the Shoulder & Under Straps.
13. Fasten the vehicle safety belt over the top of the Model 28 Harness.
14. To remove the passenger from the harness - Unfasten the buckle on the waist belt at the centre-front.
1. If ng a brand new harness, remove any Rubber Bands & unfasten the two Vercal Fixing Straps [a].
2. Holding the two Aluminium Bar Buckles [b] (aached to the upper secon of the Vercal Fixing Straps) place the back pad of the
harness against the front of the seat back & place the Fixing Straps up & over the seat back.
[b] 50mm Aluminium
Bar Buckle
3. Pass the tail-ends of the two lower secons
of the Vercal Fixing Straps [a] (on either side
of the understrap [f]), down through the gap
between the seat back & seat cushion.
Nb. The Understrap should remain lying on
the seat cushion.
4. Now feed the tail-ends of the Fixing straps up through the Aluminium Bar
Buckles (see diagram [b]) & pull down to ghten around the seat back as
securely as possible.
5. Each tail end should then be passed through the Sliplock Slide [c] to
prevent the Fixing Straps from loosening during transit.
[c] 50mm Sliplok slide
[a] Vercal Fixing Strap
[d] Shoulder Strap
[e] Waist Belt Buckle
[f] Understrap
[h]
40mm Adjuster Buckle
To Tighten Straps
Simply pull the tail-end of
the webbing strap.
The Adjuster will lock the
webbing into posion
To Extend Straps
The 40mm Adjuster is slightly spring loaded
to lock the webbing into posion.
To release the webbing you need to squeeze
the Adjuster whilst pulling on the lower
webbing strap.
[g]
[j]
[i]
Emergency Seat Belt Cuer (Oponal Extra)
We strongly recommend that a seat belt cuer is kept in the vehicle
as a safety precauon for those harnesses ed with a Steel Safety Buckle.
A simple but eecve device for ensuring the occupants of a car are able
to exit quickly and safely, parcularly in the overturned car.
It is perfectly safe as the blade is encased.
Cat. Ref: SK
Steel Safety Buckle
This buckle has proven extremely successful when ed to our
harnesses as an alternave to the standard ‘quick release’ buckle.
It helps prevent those passengers with inquisive ngers,
challenging behaviour or learning dicules from releasing the
harness buckle.
The buckle operates in reverse to the standard vehicle buckles as
it is opened by raising a spring loaded lever or over-catch and will
not press release. The spring loaded over-catch locks the buckle
when assembled and prevents accidental opening.
There is a knurled sliding bar for adjustment designed to
prevent webbing slip.
The buckle is made from Type 316 Stainless Steel and Nylon
6 and is assembled with tamper proof screws.
The 40mm buckle has a Breaking Strain of 630 kg
We recommend that the buckle instrucons provided with each
harness are displayed in a prominent posion in the
vehicle - to instruct the carer how to release the buckle mechanism
in the event of an accident.
Webbing is threaded
through the sliding
bar buckle
Loose ends of webbing
are oen passed back
through these slides to
prevent slippage & to
prevent the Fixing Straps
from loosening during
transit.
50mm Aluminium Bar Buckle
Sliplock Slide
Comfort Sleeves
Velcro Comfort Sleeves will be supplied with each harness.
These can be ed around the shoulder Straps & under strap where required.
Squeeze Adjuster
to release
webbing