User's Manual
Table Of Contents
- T40B
- T40B
- English
- 1 Safety instructions
- 2 Markings used
- 3 Application
- 4 Structure and mode of operation
- 5 Mechanical installation
- 6 Electrical connection
- 7 Shunt signal
- 8 Functionality testing
- 9 Load‐carrying capacity
- 10 Maintenance
- 11 Waste disposal and environmental protection
- 12 Ordering numbers, accessories
- 13 Specifications
- 14 Supplementary technical information
- English
- T40B
- Deutsch
- 1 Sicherheitshinweise
- 2 Verwendete Kennzeichnungen
- 3 Anwendung
- 4 Aufbau und Wirkungsweise
- 5 Mechanischer Einbau
- 6 Elektrischer Anschluss
- 7 Shuntsignal
- 8 Funktionsprüfung
- 9 Belastbarkeit
- 10 Wartung
- 11 Entsorgung und Umweltschutz
- 12 Bestellnummern, Zubehör
- 13 Technische Daten
- 14 Ergänzende technische Informationen
- 15 Dimensions | Abmessungen
- 15.1 T40B without rotational speed measurement | T40B ohne Drehzahlmessung
- 15.1.1 T40B 50 Nm - 100 Nm, Option 7, Code S
- 15.1.2 T40B 50 Nm, 100 Nm, Option 7, Code U
- 15.1.3 T40B 200 Nm, Option 7, Code S
- 15.1.4 T40B 200 Nm, Option 7, Code U
- 15.1.5 T40B 500 Nm - 1 kNm, Option 7, Code S
- 15.1.6 T40B 500 Nm - 1 kNm, Option 7, Code U
- 15.1.7 T40B 2 kNm - 3 kNm, Option 7, Code S
- 15.1.8 T40B 2 kNm - 3 kNm, Option 7, Code U
- 15.1.9 T40B 5 kNm, Option 7, Code S
- 15.1.10 T40B 5 kNm, Option 7, Code U
- 15.1.11 T40B 10 kNm, Option 7, Code S
- 15.1.12 T40B 10 kNm, Option 7, Code U
- 15.2 T40B with rot. speed measurement and reference signal | mit Drehzahlmessung und Referenzimpuls
- 15.2.1 T40B 50 Nm - 100 Nm, Option 7, Code S
- 15.2.2 T40B 50 kNm - 100 Nm, Option 7, Code U
- 15.2.3 T40B 200 Nm, Option 7, Code S
- 15.2.4 T40B 200 Nm, Option 7, Code U
- 15.2.5 T40B 500 Nm - 1 kNm, Option 7, Code S
- 15.2.6 T40B 500 Nm - 1 kNm, Option 7, Code U
- 15.2.7 T40B 2 kNm - 3 kNm, Option 7, Code S
- 15.2.8 T40B 2 kNm - 3 kNm, Option 7, Code U
- 15.2.9 T40B 5 kNm, Option 7, Code S
- 15.2.10 T40B 5 kNm, Option 7, Code U
- 15.2.11 T40B 10 kNm, Option 7, Code S
- 15.2.12 T40B 10 kNm, Option 7, Code U
- 15.1 T40B without rotational speed measurement | T40B ohne Drehzahlmessung
- Deutsch
Mechanical installation
34 A3452-10.0 T40B
Fig. 5.6 Alignment of the rotor with the stator (without a
reference signal sensor), Option 7, Code S and U
Rotational speed measurement with a sensor for the
reference signal (zero index):
Tilt the stator slightly (see Fig. 5.7, left), so that the
bracket with the sensor head for the reference signal
(zero index) is between the two flanges. Now tip the
stator over the rotor until the antenna ring completely
covers the flange with the transmitter winding (see
Fig. 5.7, right).
Information
If the stator base is already securely installed, you must
remove the upper antenna segment (see steps 1, 3 and
4). Otherwise proceed with the installation as shown in
the photos.