Operating instructions

EN
26
Rinse aid and refined salt
Only use products which have been specifically designed
for dishwashers.
Do not use table salt or industrial salt, or washing up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to any
add rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard.
(Follow the instructions given on the packaging).
If you do not add salt or rinse aid, the LOW SALT* and
LOW RINSE AID indicator lights will remain lit.
Measuring out the rinse aid
Rinseaidmakesiteasierforthecrockerytodry,aswaterruns
off surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:
•WhentheLOWRINSEAID* indicator light on the control panel
is illuminated, a reserve supply of rinse aid is still available
for1-2cycles;
1.Openthedispenser“D” by pressing and pulling up the tab
on the lid;
2.Carefully introduce the rinse aidas far as the maximum
reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
Rinse-aid dispenser setting
If you are not completely satisfied with the drying results, you
canadjustthequantityofrinseaid.
SwitchthedishwasheronandoffusingtheOn/Offbutton.Press
the Pbutton3times.SwitchonusingtheON/OFFbutton,the
indicator light of the set level flashes (set to factory level)
Adjust the level of rinse aid supply using the P button; during
this procedure the rinse aid indicator light flashes.
Press the ON/OFF button to save the setting.
IftherinseaidlevelissettoZERO(ECOcycle),norinseaidwill
besupplied.TheLOWRINSEAIDindicatorlightwillnotbelitif
you run out of rinse aid.
Up to maximum 4 levels can be set based on the dishwasher
model.
• Iftherearestreaksonthecrockery,settheadjustmentdevice
toalowernumber(1-2.)
• If there are drops of water or limescale marks,setthe
adjustment device to a higher number (3-4.)
Setting the water hardness
Everydishwasherisequippedwithawatersoftenerwhich,by
using refined salt specially designed for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the
water hardness level in your area. This information can be
obtained from your local water supplier.
Water Hardness Table
Average salt container
capacity duration**
level °dH °fH mmol/l months
1 0 - 11 0 - 20 1,1 - 2 5 months
2 12 - 17 21 - 30 2,1 - 3 3 months
3 17 - 34 31 - 60 3,1 - 6 2 months
4
*
34 - 50 61 - 90 6,1 - 9 2/3 weeks
For values between 0°f and 10°f, we do not recommend the
use of salt.
* this setting may cause a slight increase in the duration of the
cycles. ** for 1 wash cycle per day.
M
A
X
Switchthe dishwasher on andoff using the ON/OFFbutton.
Press and hold the P button for a few seconds until you hear
abeep sound. Switch the dishwasheron using the ON/OFF
button, the indicator light of the set level flashes (water softener
set to medium level).
During this procedure the salt indicator light flashes.
Adjust the hardness level using the P button,
(1-2-3-4* see water
hardness table)
up to max. 4* levels.
Press the ON/OFF button to save the setting.
Evenifusingmulti-functionaltablets,thesaltdispensershould
still be filled.
(°dH=hardnessmeasuredinGermandegrees-°f=hardness
measuredinFrenchdegrees–mmol/l=millimolesperlitre)
Measuring out the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
Refinedsaltremoveslimescalefromthewater,thusavoiding
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description) and should be filled:
• Whenthegreenfloat* cannot be seen by simply looking at
the cap of the salt dispenser;
•WhentheLOWRINSEAIDindicatorlightonthecontrolpanel
is illuminated *;
1.Remove the lower rack and
unscrew the cap (anticlockwise).
2.Thefirsttimeyoudothis:fillthe
water tank right up to its edge.
3. Position the funnel
* (see figure)
and fill the salt dispenser up to the
edge (approximately 1kg). It is
normal for a little water to leak out.
4.Removethefunnel*andwipeany
salt residues away from the opening; rinse the cap under running
water and then screw it on, the head facing downwards so as to
let the water flow out of the four slots (star-shaped) on the lower
part of the cap (cap with green float
*).
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
Whennecessary,measureoutthesaltbeforeawashcycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
* Only available in selected models.