User Guide Hotec Wireless Microphone Model: H-U06B/H-U26 Thanks for purchasing Hotec UHF Wireless microphone, please read the following instructions carefully before use. Email: support@sz-tecson.com Website: www.sz-hotec.com Facebook page: https://www.facebook.com/Hotechome/ Or scan the QR code Hotec® is the registered trademark of Shenzhen Tecson Trade and Technology Co., Ltd.
SYSTEM CONTENT H-U06B H-U06B Hand held microphone x 1 H-U06B Mini rechargeable Receiver x 1 Charging cable x 1 AA battery x 2 (for microphone) Microphone foam x 1 Anti-rolling ring x 1 TS to TRRS cable x 1 TS to TRS cable x 1 H-U26 H-U26 Hand held microphone x 2 H-U26 Mini rechargeable Receiver x 1 Charging cable x 1 AA battery x 4 (for microphone) Microphone foam x 2 Anti-rolling ring x 2 TS to TRRS cable x 1 TS to TRS cable x 1 PRODUCT INTRODUCTION Hotec UHF wireless microphone works at 902-928MHz, to
Channel B (CHB) microphone is connected, the RF indicator is solid blue. When both mics are connected, it is orange. d) Pairing the receiver and the handheld mics. The mini receiver and the handheld mics were paired before leaving the factory but in case you find the receiver is not synced with the mics, please try the steps below to pair them again manually following the steps in the Trouble Shoot #1.
Battery low indicator Red Battery is low Blue Charged Charging Red status Green indicator H-U06B AF/RF indicator H-U26 In charging Fully charged Solid blue when the mic is connected with Receiver Blinking green when there is audio signal input Green Only CHA is connected with Receiver Blue Only CHB is connected with Receiver Green/Blue Both CHA and CHB are connected with Receiver Hi/lo Hand held Microphone ON/FF: short press this button to power on / off the hand held microphone ② Battery leve
CONNECTION DIAGRAM 1. Use this wireless microphone to amplify your voice in live performances Make sure your speaker, mixer or PA/amplifier has 1/4” microphone input and microphone volume control. Step 1: Plug the mini Receiver into the 1/4” microphone input of your audio device like speaker, mixer and amplifier. Step 2: Turn the microphone volume to minimum before plug in the mini Receiver to avoid feedback or harsh loop back. Step 3: Power on the microphone and Receiver.
3. Use this wireless microphone to record audio with camera (See Figure 3) Step 1: Please make sure your camera has mic input. Step 2: Connect the TS to TRS adapter to the mini Receiver. Step 3: Connect the TS to TRS adapter to the mic input of the camera. Step 4: Turn on the mini Receiver and hand held microphone. You are ready to use when you see the correct RF/AF indicator color. Figure 3 Figure 4 PRODUCT SPECIFICATION System spec.
Hand held Microphone Spec. Carrier Frequency Power 30mw Battery Type 2 x AA Size Working Time Up to 6-8 hrs (subject to the AA battery capacity) Dimension 250 x 55 mm Weight 0.7 lb TROUBSHOOTING Issue Cause Solution Pair the mic and Receiver manually following the steps below The mic does not sync with the Receiver Mic volume is low 7 1.
amplifiers and speakers like ION Bluetooth speakers or singing machines or Hotec PA speaker. Can this be used with Android/iOS smart phones or DSLR cameras for recording? Yes, please make sure to use the correct TS to TRRS cable or TS to TRS cable. Contact Hotec seller support if you have difficult connecting it with your phone or camera. Can I sync the microphone for HU26 with the Receiver of H-U06 since my Receiver for H-U26 is broken? No.
CAUTION 1. Please do not disassemble the item by yourself. If you need support, please turn to our customer support. 2. In order to enjoy better transmission, please do not fold or cut the antenna on the Receiver 3. Please do not hold the bottom of the mic where the antenna is positioned to avoid signal transmission. 4. Please do not hold the mic head directly to the speakers, otherwise it will form a mic feedback and cause hassle. 5.
