Cleaning & Sanitizing

Remove the Front Insulation Panel, slide the Cube Guide to right. Remove the
Rubber Cap & Sleeve covering the Overflow Pipe. Unscrew the Overflow Pipe.
Clean all items (See Step 10). Once the water tank has drained, replace all the items.
In bad water conditions, a more thorough cleaning
may be required. Turn off power supply, clean all items
in a solution of 5 oz. of Scale Away per gallon of
warm water. Rinse and replace the cube guides, float
switch, water supply tubes, spray tubes and spray
guides. Turn on power supply. Otherwise, continue to
step ⓫.
Cleaning Rinse:
Turn the cleaning valve to the right until completely
horizontal (closed). Move the control switch to ICE,
replace Front Panel. After 3.5 minutes, remove the
Front Panel, move switch to OFF.
NOTICE! ICE MACHINE WILL NOT WORK,
unless valve is completely closed.
Turn the cleaning valve to the left until completely
vertical (open). Move the control switch to WASH,
replace the Front Panel. After 5 minutes, remove
the Front Panel, switch to OFF.
Remove the Front Insulation Panel, slide the
Cube Guide to right. Remove the Rubber Cap &
Sleeve covering the Overflow Pipe. Unscrew the
Overflow Pipe. Once the water tank has drained,
replace all the items.
Continue to Sanitation – Step ⓮ on front...
CLOSE
CONTROL PANEL
ICE > 3.5 minutes > OFF
OPEN

sanitizing continued…
RINSE 1: (Steps 19-21)
• CLOSE cleaning valve
• Move control switch to ICE,
replace front panel
• After 3.5 minutes, remove the
front panel
• Move control switch to OFF
• OPEN cleaning valve
• Move control switch to WASH,
replace front panel
• After 5 minutes, remove front
panel
• Move control switch to OFF
• Remove the front insulation
panel
• Slide the cube guide to right
• Remove rubber cap & sleeve
covering the overflow pipe
• Unscrew overflow pipe, drain
water tank
•
Replace the rubber cap, sleeve,
cube guide & insulation panel
RINSE 2 & 3: (Steps 22-28)
• Repeat 2x (Steps 19–21) for
complete ice/food safety
• Clean the dispenser /
storage bin liner with a
neutral cleaner (dish soap)
• Rinse thoroughly
• CLOSE the cleaning valve
• Move control switch to ICE
• Replace all panels
CONTROL PANEL
WASH > 5 minutes > OFF
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/support
Type in the model number of your
ice machine (including dashes) to
download manuals
OPEN cleaning valve:
•
To allow cleaning solution flow to
the inside the evaporator
•
Turn left to open (vertical)
CLOSE cleaning valve:
•
Must be closed for normal ice
making operation
•
Turn right to close (horizontal)
NOTICE!
IF ICE MAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
WARNING!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles
to
protect skin & eyes
from cleaning &
sanitizing chemicals
Tech Support: 1.800.233.1940
●
Scoop
●
Water Filters
●
Exterior
●
Bin Door/Top Kit
●
Ice Maker/Bin
●
Water Supply Inlet
●
Condenser
●
Water Hoses
Dish
soap, rinse well
Check psi,
change if req’d
Dish soap
& damp cloth
Warm water &
clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
●
● ●
9
10
11
19
12
13
20
21
22
29
Page 2
#51003 | 4.05.2016
30
AMMONIA
Cleaners
Need Service or Repair? Locate your closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-rep