Service Manual

37
3) Insert the evaporator bolt from the bottom into the evaporator bracket hole, and put the
plastic washer from the top. Then, screw the ange nut into the evaporator bolt while
allowing the upper evaporator to move up and down.
4) Move the control switch to the “ICE” position, and press the “RESET” button. Then, the
water tank assembly starts to close.
5) When the water tank assembly stops in its fully closed position, move the control switch
to the “OFF” position.
6) Screw in the ange nut on the evaporator bracket so that the lower and upper
evaporators xed to the water tank assembly will have a vertical gap of 1/50" - 1/25"
(0.5 - 1 mm). (When the ange nut is screwed in, the evaporator bolt moves up to raise
the upper evaporator.)
7) When the upper evaporator is vertically positioned, screw in the ange nut under the
evaporator bracket. (Use the ange nut to x the evaporator bolt to the evaporator
bracket.)
8) With the upper evaporator xed to the evaporator bracket, move the evaporator bracket
to t the upper and lower evaporators from front to back and left to right. (When the
exterior surfaces of the upper and lower evaporators t perfectly, the hemispheres
inside t and make spherical ice balls.)
9) After the upper evaporator is positioned from front to back and left to right, x the
evaporator bracket to the mechanism base.
3Dprt
B C
D E
F GA
6
5
3
4
2
1
A B C D E F G H
1
2
3
4
5
6
201802
3J
50 0 50
DRAWINGNo.
(30)
TITLE
(20)
メイショウ
図番
（ ）
DRAWN
DESIGNED
CHECKED
APPROVED
DATE SCALE
UNIT
mm
ホシザキ株式会社
HOSHIZAKICORPORATION
井上
メカニズムAY
野津
石富
1H6248 A
2019.09.13 石富 1:3
1
No. PARTSCODE NAME&SPEC. Q'TY Z
0 1H6248A01 メカニズムAY 0
寸法区分
普通寸法公差（±）単位mm角度差（±）
指示なき取
付穴のピッ
チとその累
積公差は
O
4以下 0.05 0.1 0.2 0.3 0.5 1 3 6
4をこえ16〃 0.1 0.2 0.3 0.5 0.7 1 2 3
16〃63〃 0.2 0.3 0.5 0.7 1.2 20' 1 2
63〃250〃 0.3 0.5 0.7 1.2 2.0 10' 20' 1
250〃1000〃 0.5 0.7 1.2 2.0 3.0 5' 10' 30'
1000をこえる 0.7 1.2 2.0 3.0 5.0 5' 10' 30'
J K L M N JK LM N
1
3 2020.01.09 品番22：元2個
品番29：追加
注10：追加
石富 山崎
SYMBOL P DATE REVISION DESIGNED APPROVED
表
面
処
理
等

全
面
不動態化処理
焼痕除去
脱脂洗浄
焼痕銀粉塗布
バリ無きこと
／
B-B
Evaporator Bolt
Flange Nut
Evaporator
Bracket
Collar
Upper Evaporator
Lower Evaporator
Bolt