E-bidet USER MANUAL
SAVE THESE INSTRUCTIONS
Contents Use precautions 4 Component description 5 Installation steps 6 Product description 9 Function introduction 10 Cleaning and maintenance 12 Product dimension drawing Product technical specification Warranty Card 14 16 17 18 Other matters Faults and solutions Installation and use 1 Before use Safety notes
Safety notes Read the safety instructions carefully before use so as to properly use the product. Note the following warnings relevant to the safety. Note Prohibition Compulsory observance Warning Failure to operate pursuant to the above-mentioned warning signs may result in injury or life-threatening risk. People (including children) who are deficient in body, perception, intellectual capacity, or experience and common sense (including children) are cognized.
Safety notes Do not disassemble, repair and modify products by without authorization. May result in fire or electric shock. Please unplug the power supply when cleaning the product. May result in electric shock. 3 Please don't keep the lighted cigarette or other combustion items near the product Do not bend or twist the water supply hose. May result in water leakage. May result in fire. Do not place heavy objects on the toilet seat or the toilet cover May result product damage. Do not invert product.
Use precautions Do not place this product in direct sunlight. The room temperature of toilet shall be above 0°C. It may cause product discoloration and failure of seat heating function. 4 Otherwise, it is possible to freeze the product. Use warm air and other methods to improve the temperature in the toilet. Please not use substandard power supply. Do not shower urine on the bidet body and nozzle. May cause product failure. May result in blockage.
Component description 1.Cover plate 2. Installation template 3.Fixation part Connecting bolt (2) Adjustment sheet (2) Plastic TAB(2) 5 Fixing plate 4.T-junction Rubber bushing(2) 5. Water inlet hose Butterfly nut(2) 6.
Installation steps Installation tools Cross screwdriver Monkey wrench Barrel and rag Attention before installation 1.Water pressure range: 0.1-0.75 MPa, please follow the instructions. 2.Corner valves shall be located close to the location where this product is installed and disassembled. 3.Please use the braided hose that comes with the product to prevent water leakage. 4.When installing braided hose,be careful to prevent the black gasket falling out. 5.
Installation steps 4.To ensure the normal use of the product, please press reset key before installation; 5.Slightly push the cover into fixing plate until you heard "click" , indicating that the cover has been installed in place. Note Press to maximum stroke and hold for 2 seconds K CLIC 6.Close the water valve； 7.
Installation steps 8.Installation tee； inlet valve inlet valve 4 tee hose hose hose 2 hose tee angle valve Normally,the tee is installed on the angle valve 9.Open the angle vavle to check for water leakage； angle valve if the angle valve and wall is too close,you can installed the tee under the inlet valve 10.Turn on the knob to check whether the nozzle is protruding； 8 11.
Product description Toilet cover Toilet seat Nozzle Knob Water supply hose joint 9 Power socket Drain plug Disassembly button (Reset button) Temp.
Function introduction Standby mode 1.After the power supply is connected, the “bi” indicates that the cover can be used normally. 2.Water temperature by default at low gear: about 35℃. 3.Seat temperature by default at low gear: about 33℃. Rinsing function 1.Bidet/Hip Rinsing Bidet After sitting down, there is a beep prompt, rotating the knob to start rinsing Hip 2.
Function introduction Description of function Function setting key Lighting Lighting TIP OFF Water/wind temp. setting key OFF LOW HIGH Seat temp. setting key Repeatedly press will switch over water temp. in the sequence indicated in the left figure. Change water temp. :a short sound. Turn off water temp. :a long sound. HIGH LOW Repeatedly press will switch over wind temp. in the sequence indicated in the left figure. LOW HIGH MID OFF HIGH low : about 35℃. high : about 38℃. Change wind temp.
Cleaning and maintenance Manual cleaning of spray tube - Gently pull out the nozzle and dip the neutral detergent with a soft cloth, sponge or small brush. - Gently support the nozzle, wipe the spray tube and nozzle. Clean filter screen 2 Braided hose 12 A A Filter screen Tips: - Make sure that the corner valve close and the power off before you clean the filter screen； - Clean the filter screen when the water flow is less than normal hours.
Cleaning and maintenance Product maintenance in winter when the temperature of toilet below 0℃： -Pull out the power plug. -Remove water inlet hose from the angle valve to the toilet end, and empty the water in the water inlet hose; -Remove the bottom nut,and drain internal water. Not use in a long time When this product is not used for a long time, drain the water in the product and cut off the power supply: - Pull out the power plug. - Close angle valve and stop the water inlet.
Faults and solutions Common fault diagnosis When you think it is a fault, try some of the following processing methods. If the product is still not working properly, contact your local repair center or call the service hotline. Check power supply Check water supply 1.If power supply is under normal state. 2.Mannual reset thermostat(Istallation step4) Note 1.If water supply is under normal state. 2.If corner valve is closed.
Faults and solutions Failure analysis of seat Phenomenon The seat is cold Possible cause The seat heating is turned off The product started the Temperature drops low temperature scald When rinsing prevention function Solution Turn on the heating function in advance After cleaning, the setting temperature will rise again Failure analysis of light Phenomenon Solution Possible cause Night light is not ON.
Product dimension drawing Product dimension drawing V-shape 370 300 203 374 16 434-490 132-178 508 87 size: mm
Product technical specification Items Description Rated voltage 120 V~, 60 Hz Rated power 1050 W Max. transient power 1450 W Length of power line About 1.1m Water supply pressure 0.1 - 0.
Warranty Card To dear customers: Thank you for choosing our E-bidet! If any problem occurs during use, please simply remove and check the problems pursuant to the user's manual. When you cannot remove such problems, contact your local supplier or call the service hotline. I. Information: Customer information Customer name Address TEL Dealer information Name TEL Model Purchase date Y M D Product series number Warranty Two-year free warranty since period the purchase date II.
