Operating Instructions and Installation Instructions

43
06.2004 TR10A014 RE
ENGLISH
LED: flashes 2 x in 4 seconds
Cause: A photocell or closing edge safety device con-
nected to terminals 20 and 74 has been inter-
rupted or activated. It is possible that a safety
return has been initiated.
Elimination: Remove the obstruction in question, check the
photocell and / or closing edge safety device,
and if necessary replace.
Note: If no photocell or closing edge safety device is
connected to terminals 20 and 74, check whether
the factory assembled resistance of 8,2 kΩ bet-
ween terminals 20 and 74 is present – if neces-
sary connect.
Acknow-
ledgement: Another impulse is generated via an external
button, the remote control or the transparent
button – the door travels in the opposite direc-
tion to that last travelled.
LED: flashes 3 x in 5 seconds
Cause: The CLOSE force limit has been activated –
the door has carried out a safety return.
Elimination: Remove the obstruction. If a safety return has
taken place for no recognisable reason, check
the door mechanics. It may be necessary to
delete the door data and reprogramme.
Acknow-
ledgement: Another impulse is generated via an external
button, the remote control or the transparent
button – the door opens.
LED: flashes 4 x in 6 seconds
Cause: The STOP or emergency-OFF circuit is open
or was opened during a travel cycle (see
section 3.5.3)
Elimination: Close the STOP or emergency-OFF circuit
(see section 3.5.3)
Acknow-
ledgement: Another impulse is generated via an external
button, the remote control or the transparent
button – the door travels in the opposite direc-
tion to that last travelled.
LED: flashes 5 x in 7 seconds
Cause: The OPEN force limit has been activated –
the door has stopped whilst opening.
Elimination: Remove the obstruction. If the door has come
to a halt for no recognisable reason, check the
door mechanics. It may be necessary to delete
the door data and reprogramme.
Acknow-
ledgement: Another impulse is generated via an external
button, the remote control or the transparent
button – the door closes.
LED: flashes 6 x in 8 seconds
Cause: Operator fault
Elimination: It may be necessary to delete the door data. If
the operator fault re- occurs, replace the operator.
Acknow-
ledgement: Generate an impulse via an external button,
the remote control or the transparent button –
the door opens (OPEN reference cycle).
LED: flashes 7 x in 9 seconds
Cause: The operator has not yet been programmed
(this is merely being pointed out – it is not a
fault/error).
Elimination/
Acknow-
ledgement: Initiate learn operation for the CLOSE direction
via the transparent button.
LED: flashes 8 x in 10 seconds
Cause: The operator requires a reference cycle (this is
merely being pointed out – it is not a fault/error).
Elimination/
Acknow-
ledgement: Initiate a reference cycle in the OPEN direction
via an external button, the remote control or
the transparent button.
Note: This is the normal state following a power failure
when no door data is stored or this has been
deleted and/or the last door position is not
sufficiently well known.
4 Terms and Conditions of the Warranty
Guarantee Period
In addition to the statutory guarantee provided by the
dealer, we provide the following guarantee of parts from
the date of purchase:
a) 5 years on operator mechanics, motor and motor
controls
b) 2 years on radio, impulse generators, accessories
and special systems
There is no guarantee on consumables (e.g. fuses,
batteries, lighting devices).
Claims made under the guarantee do not extend the
guarantee period. Following the supply of replacement
parts the guarantee period is six months; or at least,
the remainder of the guarantee period.
Conditions
A claim under this guarantee is only valid for the country
in which the equipment was bought. The product must
have been purchased through authorised distribution
channels. A claim under this guarantee exists only for
damage to the product in the contract itself. Reimburse-
ment of expenditure for dismantling and installation,
testing of corresponding parts, as well as demands for
lost profits and compensation for damages, are excluded
from the guarantee. The receipt of purchase substan-
tiates your right to claim under the guarantee. ➤