Operating Instructions and Installation Instructions
41
06.2004 TR10A014 RE
ENGLISH
When a hand transmitter / receiver set is included, the top
button on the hand transmitter is generally already pro-
grammed into the receiver.
For information on how to programme in hand transmitter
buttons on other receivers, please refer to the instructions
supplied with the receiver.
Note
Completely unroll the aerial wire and fasten to the garage
ceiling, if possible upwards as well as diagonally in the
direction of the structural opening. In doing so, do not wind
the aerial wire around metal parts such as nails, braces etc.
The best alignment to achieve an optimum range must be
established by trial and error.
868 MHz: GSM 900 mobile phones used at the same time
may influence the range of the radio remote control.
3.5.2 Connecting external IMPULSE buttons to start
or stop door travel cycles
One or several buttons with normally open (n.o.) contacts
(potential-free), such as internal buttons or key switches,
are connected (in the case of the latter, then joined
parallel) as follows (see figure 12):
1) first contact to terminal 21a (impulse input).
2) second contact to terminal 20 (0 V).
Note
If an auxiliary voltage is needed for an external button, then
a voltage of approx. + 24 V DC is available for this at termi-
nal 5 (as opposed to 0 V at 20), whereby the total current
drawn off at terminal 5 must not exceed 100 mA.
3.5.3 Connecting an OFF-switch or a wicket door contact
(opening must be forcibly actuated) to halt and/or
switch off the operator (STOP or emergency-OFF
circuit)
An OFF-switch with normally closed (n.c.) contacts
(switching to 0 V or potential-free) is connected as
follows (see figure 13):
1) The jumper inserted at the factory between terminal
12 (STOP or emergency-OFF input) and terminal 13
(0 V), allowing normal function of the operator, should
be removed.
2) - Switching output or first contact at terminal 12
(STOP or emergency-OFF input).
- 0 V (Ground) or second contact to terminal 13 (0 V).
Note
By opening the contact any possible travel cycles are
immediately halted and permanently prevented.
3.5.4 Connecting a photocell or a closing edge safety
device to initiate a safety return up to the OPEN
end-of-travel position
Option A:
A photocell or closing edge safety device of type A
(everything okay = contact closed) switching to 0 V
or having a potential-free contact, is connected as
follows (see figure 14):
1) The resistance of 8.2 kΩ inserted at the factory bet-
ween terminals 74 (safety device-input SE) and 20
(0 V) must be removed and then reinserted in the
safety device, as shown, between the switching
output and terminal 74.
2) 0 V (Ground) or second contact to terminal 20 (0 V).
Option B:
A photocell or closing edge safety device of type B
(everything okay = contact opened) switching to 0 V
or having a potential-free contact, is connected as fol-
lows (see figure 15):
1) The resistance of 8.2 kΩ inserted at the factory bet-
ween terminals 74 (safety device-input SE) and 20
(0 V) must be removed and reinserted in the safety
device, as shown. The switching output is connected
to terminal 74.
2) 0 V (Ground) or second contact to terminal 20 (0 V).
Note
If an auxiliary voltage is needed for the safety device, then
a voltage of approx. + 24 V DC is available for this at termi-
nal 5 (as opposed to 0 V at 20), whereby the total current
drawn off at terminal 5 must not exceed 100 mA.
3.5.5 Connecting to the options relay
The potential-free contacts of the options relay allow con-
nection, for example, an external light or a warning light
without automatic flashing (see figure 16).
To feed an external light, external voltage must be used!
Terminal .6 n.c. contact max. contact
Terminal .5 common contact load:
Terminal .8 n.o. contact 2,5 A / 30 V DC
500 W / 250 V AC
Note
The voltage of + 24 V DC available at terminal 5 cannot
be used to feed an external light!
3.6 Notes on operating the garage door operator
Note
Initial function checks as well as programming or exten-
ding the remote control should always take place from
inside the garage.
Only ever operate the garage door operator when you
have full view of the movement range of the door. Wait
until the door has come to a complete halt before ente-
ring the door's movement zone.
Before driving in or out of the garage, always check that
the door has fully opened.
ATTENTION
Keep hand transmitters out of the
reach of children!
➤