EN
Thank you for choosing this product. We are proud to offer the ideal product for you and the best complete range of home appliances for your daily routine. WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). It is important to have WEEE subjected to specific treatments, in order to remove and dispose properly all pollutants, and recover and recycle all materials.
l This appliance is intended to be used in household and similar applications such as: - Staff kitchen areas in shops, offices and other working environments; - Farm houses; - By clients in hotels, motels and other residential type environments; - Bed and breakfast type environments. A different use of this appliance from household environment or from typical housekeeping functions, as commercial use by expert or trained users, is excluded even in the above applications.
l Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the washer dryer. WARNING: never stop a washer dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
consult the product technical l Do not pull on the power cord specification please refer to the or appliance to unplug the manufacturer website. machine. Electrical connections safety instructions l Make sure there is no water in the drum before opening the door. and l The technical details (supply voltage and power input) are indicated on the product rating plate WARNING: water may reach very high temperatures during the wash cycle.
2. INSTALLATION l Remove the 2 or 4 transportation screws (A) on the back and remove the 2 or 4 flat washers, rubber bungs and plastic spacer tubes (B) as illustrated in figure 1. l If the washing machine is built-in, unscrew the 3 or 4 transportation screws (A) and remove the 3 or 4 flat washers, rubber bungs and plastic spacer tubes (B).
EN Instructions for mounting the furniture door l Position the template onto the reverse of the furniture door. It is possible to mount the hinges and closure magnet on the right or left-hand side depending on your requirements. Mark the screw hole positions, then drill out these positions. B C A l Fix the hinges in place with the 4 screws provided (A). l Fix the magnet (B) in place using screw (C).
l Mount the furniture door to the front of the washer using the hinges. Fix the spacers (I) in place with the 2 screws (J) and then fix the hinges with 2 screw (H). H J I We suggest mounting the furniture door so that it opens towards the left, which is the same direction as the porthole door. This will leave more space when you are loading washing into the appliance. l Slide 60 4 adjustable feet allow the height of the washer to be adjusted from 820 mm to a maximum of 840 mm.
Hydraulic connections 3 EN l Connect the water hose to the water supply tap (fig. 3) only using the hose supplied with the appliance (do not reuse old hose-sets). l SOME MODELS may include one or more of the following features: 4 l HOT&COLD (fig. 4): water mains connection settings with hot and cold water for higher energy savings. Connect the grey tube to the cold water tap and the red one to the hot water tap.
Setting 7 l The washing machine should be installed in its final position such that the water fill hose is not kinked or trapped. The corrugated drain hose should be inserted into suitable drain pipe of between 50 cm and 85 cm height above the floor using the curved drain hose support. If an under sink connection is used the drain hose must be routed above the sink overfill opening to prevent back siphoning. Care must be taken to avoid kinking or trapping the drain hose (fig. 7).
3. DETERGENT DRAWER 3 9 EN The detergent draw is split into compartments as illustrated in figure 9: l compartment "1": for prewash detergent; l compartment “ ”: for special additives, 1 softeners, starch fragrances, etc.; 2 WARNING: only use liquid products; the washing machine is set to automatically dose additives at each cycle during the last rinse. l compartment "2": for 10 washing detergent. A liquid detergent cup is also included IN SOME MODELS (fig. 10).
Maximise the load size 4. PRACTICAL HINTS l Achieve the best use of energy, water, Load tips When sorting laundry, make sure: - have eliminated metallic objects such as hair clips, pins, coins, from laundry; - to have buttoned pillow cases, closed zips, tied loose belts and long robe ribbons; - to have removed rollers, hooks or clips from curtains; - to have carefully read clothing washing labels; - to have removed any persistent stains using specific detergents.
For washes between 40°C and 60°C the type of detergent used needs to be appropriate for the type of fabric and level of soiling. Normal powders are suitable for “white” or colour fast fabrics with high soiling, while liquid detergents or “colour protecting” powders are suitable for coloured fabrics with light levels of soiling. For washing at temperatures below 40°C we recommend the use of liquid detergents or detergents specifically labeled as suitable for low temperature washing.
l Fill the drawer with hot water. 5. CLEANING AND MAINTENANCE Looking after your appliance correctly can extend its lifespan. Cleaning the appliance’s exterior l Disconnect the machine from the power supply. l Clean the appliance’s external cabinet, using a damp cloth and AVOIDING ABRASIVES, ALCOHOL AND/OR DILUENTS. Drawer cleaning l It is advisable to regularly clean the detergent drawer to avoid the accumulation of detergent and additive residues.
S u g g e s tio n s fo r m o v e s o r prolonged disuse l The appliance has a special filter that traps larger residues that could block the draining system, such as buttons or coins (depending on the model, consider version A or B). We recommend checking and cleaning the filter 5 or 6 times a year. l Disconnect the machine from the power supply. l Ensure all the water has been emptied from the drum.
6. QUICK USER GUIDE This washing machine automatically adjusts the level of the water to the type and quantity of washing. This system gives a reduction in energy consumption and a saving in washing times. 7. CONTROLS AND PROGRAMS A Program selection l Turn on the washing machine and select the required program. l Adjust the washing temperature if necessary and press the required "option" buttons.
PAUSING THE MACHINE l Keep the START/PAUSE button pressed for about 2 seconds (some light indicators and the residual time display will flash, showing that the machine is paused). When the programme selector is turned the display lights up to show the settings for the programme selected. For energy saving, at the end of the cycle or with an inactivity period, the display level contrast will decrease.
- Confirm by pressing the START/PAUSE button. The delay countdown will begin and when it has finished the programme will start automatically. l It is possible to cancel the delay start by turning the programme selector to OFF. If there is a break in the power supply whilst the machine is operating, when the power is restored, the machine will restart from the beginning of the phase it was in when the power was lost.
- Steam Refresh (two button pushes) P3 appears on the display Thanks to the steam action, the cycle lets to refresh and relax clothes’ creases after use. This programme consists of a start phase in which the steam in introduced and the excess moisture is removed at the final stage to allow prompt use. This cycle is suitable for dry clothes. TEMPERATURE SELECTION button l This button allows you to change the temperature of the wash cycles.
l During the initial filling phase of the cycle KEY LOCK l Pressing simultaneously the buttons TEMPERATURE SELECTION and SPIN SPEED for about 3 seconds, the machine allows you to lock the keys. In this way, you can avoid making accidental or unwanted changes if a button on the display is pressed accidently during a cycle. l The key lock can be simply cancelled by pressing the two buttons simultaneously again or turning off the appliance.
6) WASH TEMPERATURE LIGHTS - recognises the presence of too much soap suds, and if necessary, adjust the amount of rinse water. This shows the washing temperature of the selected programme that can be changed (where allowed) by the relevant button. If you want carry out a cold wash all the indicators must be off. - adjusts the spin speed according to the load, thus avoiding any imbalance. 5) KEY LOCK INDICATOR LIGHT The indicator light show that the keys are locked.
Table of programmes 1) (MAX.) * PROGRAMME 2 (see control panel) (MAX.
INFORMATION FOR THE TEST LABORATORIES STANDARD PROGRAMMES ACCORDING TO Directive 96/60/CE (Only for models with liquid detergent compartment) When only a limited number of articles have stains which require treatment with liquid bleaching agents, preliminary removal of stain can be carried out in the washing machine. Pour the bleach into the liquid bleach container, inserted into the compartment marked "2" in the detergent drawer, and set the special programme RINSE.
Description of programmes To clean different types of fabrics and various levels of dirt, the washing machine has specific programs to meet every need of washing (see table of programmes). Choose programme in accordance with the laundry instructions appearing on labels, especially the maximum recommended temperature.
Allergy Care 60° This programme offers thorough cleaning of all cotton items, sanitising and eliminating bacteria. It is an efficient high temperature washing cycle. Recommended for small loads. Dry Wool Low temperature drying programme, ideal to dry woollen clothes with maximum care and softness, reducing rubbing of fabrics and avoid possible felting. It’s suggested to reverse clothing before drying. Timing is related to the amount of the washing and the spin speed selected for the wash.
8. DRYING CYCLE The correct way to dry l Drying guidance advice is general, but practical experience of using the product will help you to achieve the best drying results. l We recommend setting a lower drying time than indicated, when first using the appliance in order to establish the degree of dryness required. l We recommend not drying fabrics that l Open the door. l Fill with the laundry, not exceeding the maximum drying load indicated in the programme table. For large items (e.g.
l The washer dryer will calculate the time needed for drying and the level of moisture remaining in the laundry, according to the load and drying type selected. l Check that the tap is turned on and that the discharge correctly. hose is positioned l When the programme is finished the word "End" will appear on the display. After 5 minutes the appliance will go into standby mode (on certain models, the display will show two lines).
l At the end of the wash phase the display 9. AUTOMATIC WASHING/ DRYING CYCLE will show the drying time remaining. l The drying programme indicator will be You cannot exceed the maximum dryable load of laundry indicated in the programme table, otherwise the laundry will not be dried satisfactory. on, until the cool down phase begins and the corresponding indicator is on. l When the programme is finished the word - Washing l Open the drawer and put in the correct amount of detergent.
If you believe the washing machine is not working correctly, consult the quick guide provided below which includes some practical tips on how to fix the most common problems. ERROR CODE FORMAT l Models with a display: the error is shown by a number preceded by the letter “E” (example: E2 = Error 2). l Models without display: an error is shown by a sequence of flashes of every LED.
OTHER ANOMALIES Problem Possible causes and practical solutions The washing machine does not work / start The washing machine does not spin Make sure the product is plugged into a working supply socket. Make sure power is on. Make sure the wall socket is working, testing it with another appliance such as a lamp. The door may not be correctly closed: open and close it again. Check whether the required program was correctly selected and the start button pressed.
Warranty The product is guaranteed under the terms and conditions stated on the certificate included with the product. The certificate has to be stored so as to be shown to the Authorized Customer Service Centre in case of need. You can also check the warranty conditions on our web site. To obtain assistance, please fill in the form on-line or contact us at the number indicated on the support page of our web site.
- HBDS D A E - 20.05 - 43035841 - IDM s.r.l.
