HOOVE ® TM ENGLISH ,.P pp. 1-17 ESPANOL ,._ p_g. 18-27 FRAN(_AIS ,._ p. 28-37 Dee p Cleaner The Easy to Use Deep SteamVac by applying www.hoover.com TM Cleaner Dual V TM Deep Cleaner cleans carpet hot tap water and cleaning solution.
|mpo ant Safeguards! When using an electrical appliance, the following: always follow READ ALL INSTRUCTIONS basic precautions, including BEFORE USING APPLIANCE. WARNING: . Connect to a properly grounded outlet only. See "Grounding Instructions". . Do not clean over floor electrical outlets. . Do not use without tanks in place. . Do not use with damaged cord or plug.
Thank you for choosing a HOOVER Contents product. Important safeguards .......... 2 Parts needed for assembly ....... 3 Assembling deep cleaner ...... 4-6 Deep cleaner description ........ 7 General operation ............ 7-9 Filling the clean water tank... 8-9 Emptying the recovery tank .... 9 Brush speed selector ......... 8 Automatic shut-off ............ 8 How to use Before you begin ........... 10 After cleaning ............ 10-11 Cleaning carpet ............. 11 Cleaning bare floors .........
The assembled cleaner will look like this drawing. Model with SpinScrub TM hand tool is shown. Aj i Attach upper handle Remove clean water tank (upper tank) from deep cleaner. tl NOTE: If the cord protector (A) on back of handle should become dislodged during unpacking, make sure it is repositioned properly before continuing with assembly of your deep cleaner. With the arrow (B) on the cord protector pointing down, press groove (C) in the cord protector into slot in the lower handle.
IEl;l Rotate top of caddy toward cleaner handle. Slide caddy down so notch (G) on caddy rests in hook (H) on cleaner. Identify the hose parts before storing hose. I. Nozzle connector end J. Solution tube Storing tools Press hose into opposite side of caddy. Loop hose at bottom of cleaner and press into top of hook (K). Loop Slide Snap hose Repeat on other end of hose. Press solution tube (J) into opposite side of clip.
r_d:] f Pull tool down and outward. To reposition the tool, reverse this procedure. How to reattach cover tool The tool cover is designed with a breakaway feature which allows it to snap free if it is pushed open too far. To reattach, align hinges of cover with holes on sides of tool storage area. Snap door into place.
Deep Cleaner The assembled deep cleaner will look like the drawing. Model with SpinScrub TM hand tool is shown. Description 1. 2. 3. 4. 5. 21 14 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23.
Carrying handle The deep cleaner may also be lifted by placing a hand above the upper clean solution tank handle as shown. Automatic shut off Brush setting selector When the recovery tank (lower tank) is full the automatic shutoff mechanism will shut off the deep cleaner suction (suction will be noticeably reduced). Your 'SteamVac' deep cleaner has two agitator brush settings. At that time, the yellow float disk will rise to the top of the recovery tank lid (B).
_J Carrytanktoa sink. Turntankcapcounterclockwise and remove cap. Fill tank (E) (1 gallon) with hot tap water. CAUTION: Do not fill with water above 140°F (60°C). To fill detergent container (F), turn cap counterclockwise and remove cap. Replace tank cap and tighten. NOTE: Use only HOOVER detergents. They are specially formulated for use with your 'SteamVac' deep cleaner. CAUTION: Detergents contain Anionic and Nonionic Surfactants. Avoid contact with eyes and skin.
Before you begin cleaning a. Vacuum thoroughly - For carpet, use a HOOVER vacuum cleaner with an agitator for best results. Vacuum upholstery with a vacuum cleaner with cleaning tool attachments. Use a crevice tool to reach into tufts and folds. Do not use the 'SteamVac' deep cleaner as a dry vacuum cleaner, b. For upholstery, check cleaning code - Use your HOOVER 'SteamVac' deep cleaner only if the upholstery fabric is marked with a "W" (for "wet" clean) or "S/W" (for "solvent/dry" or "wet" clean).
To clean nozzle If lint or other debris becomes lodged in nozzle, it can be removed for cleaning. To replace nozzle, line up tabs (A) on nozzle with holes (B) in cleaner. Slide tabs into holes. Unplug deep cleaner from electrical outlet. Slide nozzle completely onto cleaner. Press down on nozzle to secure it. Replace recovery tank (Fig. 2-17). Remove both tanks as described in Fig. 2-16. With handle in upright position, tilt cleaner back so that handle rests on the floor.
6. Set Wash/Rinse switch to WASH. Turn cleaner ON. How to attach attachment bare 7. To release solution, press trigger. Slowly move deep cleaner forward and backward over area to be cleaned. floor (Available at additional cost if not included with your cleaner.) 8. To pick up dirty solution, release trigger and slowly move deep cleaner over area where solution has just been dispersed. Use both forward and reverse strokes. Unplug deep cleaner from electrical outlet.
Select tool How Your model includes some combination of the following tools, but may not include them all. I I..........U,,,[_ G. SpinScrub TM hand tool has rotating brushes for extra scrubbing action on small carpet areas, carpeted stairs and upholstery. For some models, the brushes can be removed for converting to the scrub module. H. Stair/upholstery nozzle has a built-in brush to help provide the scrubbing action some spots may need for removal. I.
After using scrub tool To clean scrub pad, pull it off module. Wash it in water with mild detergent. Rinse and let air dry. Pad must be completely dry before reattaching to module. Replacement pads may also be purchased. Ask for HOOVER part no. 40308001. Using the scrub tool With a little solution, test the scrub tool on a hidden area before using on the desired surface. If no surface change is visible, continue to use as described below. 1. Attach hose and solution tube as instructed in Figs.
Read "Before you begin cleaning" instructions on page 9. Be sure to check the cleaning code on your upholstery. Use your deep cleaner only on upholstery marked "W" or "W/S". 1. Attach hose and solution tube as instructed in Figs. 3-10 to 3-12. 2. Place handle in upright position. Agitator brushes will not rotate while handle is in upright position. 3. Fill clean water tank according to instructions for Figs. 2-9 to 2-12. 4.
Storage Before storing: • Empty clean water tank and let air dry. Replace on deep cleaner. • Unused detergent can be stored in the detergent container. • Empty recovery tank, rinse tank and lid thoroughly with clean water and let air dry. Allow brushes and underside of deep cleaner to air dry thoroughly before storing deep cleaner on a carpeted or wood surface. Do not store deep cleaner with a full clean water tank in place.
Service Fu|| One Year To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: ,, checking the Service section of The Hoover Company on-line at www.hoover.