HOOVER _ L __ Deep EEE IW_ SteamVac applying hoover.com L. Cleaner The Easy to Use Deep www, TM V2 TM Deep hot tap water TM Cleaner I ENGLISH ,._ pp. 1-15 ESPAI_OL ,._ pag. 16-25 FRAN(_AIS ,._ p. 27-35 Cleaner cleans carpet and cleaning solution.
Grounding Instructions When using the following: an electrical READ ALL appliance, always INSTRUCTIONS foIIow BEFORE basic precautions, USING APPLIANCE. including A B @ @ To reduce the risk shock, or injury: • Use indoors of fire, electric only. • Use only the cleaning product. on surfaces moistened by process. Do not immerse • Connect outlet only. Instructions'. to a properBy grounded See "Grounding • Do not outlets. clean • use without Do not • Do not flit (60°C).
Thank you for choosing a HOOVER Contents product. Important safeguards .......... 2 Parts needed for assembly ....... 3 Assembling deep cleaner ...... 3-5 Deep cleaner description ........ 6 General operation ............ 6-8 Filling the clean water tank ... 7-8 Emptying the recovery tank .... 8 Brush speed selector ......... 7 Automatic shut-off ............ 7 How to use If you need any assistance: Visit our website at www.hoover.com.
The assembled drawing. = 1 cleaner will look like this Aj Attach upper handle Remove clean water tank (upper tank) from deep cleaner. _-- NOTE: If the cord protector (A) on back of handle should become dislodged during unpacking, make sure it is repositioned properly before continuing with assembly of your deep cleaner. With the arrow (B) on the cord )rotector pointing down, press groove (C) in the cord protector into slot in the lower handle.
;_.:] Rotate top of caddy toward cleaner handle. Slide caddy down so notch (G) on caddy rests in hook (H) on cleaner. Identify the hose parts before storing hose. I. Nozzle connector end J. Solution tube EEP_ Storing tools hose and Press hose, a few inches from nozzle connector end (I), into caddy. Bring hose up and over top of caddy. EEEI + yL_ Press hose into opposite side of caddy. Loop hose at bottom of cleaner and press into top of hook (K). Loop hose over top of caddy again.
Deep Cleaner The assembled Description P:Sl 1. 2. 3, I _4 21 17 19 18 7_ 8_ 20 10_ 1_5 21. 22. 14 ....... i 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. deep cleaner will look like the drawing.
Carrying handle The deep cleaner may also be lifted by placing a hand above the upper clean solution tank handle as shown. Automatic shut off Brush setting selector When the recovery tank (lower tank) is full the automatic shutoff mechanism will shut off the deep cleaner suction {suction will be noticeably reduced). Your 'SteamVac' deep cleaner has two agitator brush settings. At that time, the yellow float disk will rise to the top of the recovery tank lid (B).
P-,_P4 P_EI IE Carry tank to a sink. Turn tank cap counterclockwise remove cap. and Fill tank (E) (1 gallon) with hot tap water. CAUTION: Do not fill with water above 140°F (60°C). To fill detergent container (F), turn cap counterclockwise and remove cap. Replace tank cap and tighten. NOTE: Use only HOOVER detergents. They are specially formulated for use with your 'SteamVac' deep cleaner. CAUTION: Detergents Anionic and Nonionic contain Surfactants. Avoid contact with eyes and skin.
Before you begin a, Vacuum thoroughly ° For carpet, use a HOOVER vacuum cleaner with an agitator for best results. Vacuum upholstery with a vacuum cleaner with cleaning tool attachments. Use a crevice tool to reach into tufts and folds.
To clean nozzle If lint or other debris becomes lodged in nozzle, it can be removed for cleaning. m J To replace nozzle, line up tabs (A) on nozzle with holes (B) in cleaner. Slide tabs into holes. Unplug deep cleaner from electrical outlet. Slide nozzle completely onto cleaner. Press down on nozzle to secure it. Remove both tanks as described in Fig. 2-16. With handle in upright position, tilt cleaner back so that handle rests on the floor. Replace recovery tank (Fig. 2-17).
6. Set Wash/Rinse switch to WASH. Turn cleaner ON. How to attach attachment bare 7. To release solution, press trigger. Slowly move deep cleaner forward and backward over area to be cleaned. floor (Available at additional cost if not included with your cleaner.) Unplug deep cleaner from electrical outlet. To prevent possible leaking, remove clean water tank (Fig. 2-10) and recovery tank (Fig. 2-16) before positioning bare floor attachment. Set tanks aside (do not set tank on furniture). 1.
How The utility nozzle has a built-in brush to help provide the scrubbing action some spots may need for removal. to attach tool Unplug deep cleaner from electrical outlet. 1. Place handle in upright position and remove hose from rack. 2. Connect tool to hose by sliding it onto connector until the tab (J) locks it securely. Using your thumb, push forward and up on the latch (K) to remove tool. After using tool Drain suction hose by turning deep cleaner ON and holding nozzle up for several minutes.
Read "Before you begin cleaning" instructions on page 9. 1. Attach hose and solution tube as instructed in Figs. 3-10 to 3-12. 2. Place handle in upright position. Agitator brushes will not rotate while handle is in upright position. 3. Fill clean water tank according to instructions for Figs. 2-9 to 2-12. 4. Fill detergent container with HOOVER Carpet/Upholstery Detergent according to instructions for Figs 2-13 to 2-15. 5. Attach tool to end of hose. 6.
Removable brushes B D B Your deep cleaner is equipped with removable brushes for easy cleaning. To remove brushes Disconnect cleaner from electrical outlet. To prevent possible leaking, remove clean water tank and recovery tank. Set tanks aside. Grab brush assembly and pull firmly. The brushes can be cleaned under running water. To replace brushes Align posts (A) on both ends of brush assembly with slots (B) in cleaner housing.
Service To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: checking the Service section of The Hoover Company on-line at www.hoover, com OR 2. Turn valve cap (A) counterclockwise and remove. Soak valve cap in warm water for at least 15 minutes. Wipe cap dry.
HOOVER y HOOVER and _ R1 11-02 F7210-900 HOOVER et _)sont son marcas registradas des marques d6posees are registered trademarks Litho USA 56518-149
