Quick Start Guide

ManualsBrandsHoonved ManualsDishwasherC43E

ENGLISH

Part 3: For the technician

IMPORTANT

Every operation of installation, electrical or hydraulic

connection, programming, maintanance etc...has to be

carried out by QUALIFIED personnel, authorised by the

manufacturer;

any interventions carried out by UNQUALIFIED

personnell, may compromise the technician’s own safety,

as well as the safety of other personnel (operators, etc.)

or of any other equipment connected to the washing

machine.

The manufacturer declines all responsibility for

accidents or damage to persons or property caused

by failure to comply with the above listed provisions.

3.1 INSTALLATION (Fig. 6-7)

- After having removed the packing, make sure that the

machine is in a perfect condition and that all the parts

have been included.

- Position the machine in the required setting.

3.1.a Connecting the drain pipe (Fig. 6)

- Fix the drain pipe (11) to the relative preset outlet.

IMPORTANT

It is essential to ensure that the drain pipe that it is not

throttled in any part.

3.1.b Connection to the water main (Fig. 6-7)

- Screw the end of the fill pipe (12) to a 3/4”G threaded

cock, fitting the filter (13 Fig. 7) in between.

ATTENTION

It is essential to connect the cold water delivery pipe to a

throttle cock in order to separate the water main from the

machine itself. Also make sure that there are no sharp

bends.

If there is sand in the water main, it will be necessary to

install a filter between it and the machine. If the water main

is without, it is advisable to install a decalcifier prior to the

machine with a setting of min. 4 and max. 8 French

degrees.

The manufacturer declines all responsibility for

damage to the machines caused by failure to comply

with the above listed provisions.

3.1.c Connection to the water main (Fig. 6-7)

DANGER

- Before connecting to the electricity main, always

check that the data pertaining to the power source

correspond to those indicated on the identification

plate (pos. 9 Fig. 5) and that the main electric power

switch installed prior to the machine is

disconnected “0” OFF.

- An appropriately sized omnipolar circuit-breaker

with a minimum 3 mm gap between its contacts

must be installed between the power supply main

and the machine.

- The manufacturer declines all responsibility for

accidents or damage to persons or property caused

by failure to comply with the above listed provisions.

• Connect the electrical power cable (14) to the main

switch installed prior to the machine.

• Connect the equipotential ground conductor to the

terminal (15).

3.2 SETTING CYCLES for REGENERATION

PROMPT

(models C D-SP D only)

ATTENTION

Before setting the cycles for the resin regeneration prompt,

SWITCH OFF the dishwasher by pressing the power

switch (IL) into the OFF position, and SWITCH the mains

power supply to the “ O ” OFF position.

It is now possible to carry out the cycle settings for the

regeneration-phase prompt.

IMPORTANT

We recommend that setting the regeneration cycle prompt

should be the first operation you carry out.

With the machine SWITCHED OFF and the door OPEN,

set the dip switches as shown in the following table:

Having set the dip switches, switch the machine back on

at the mains “ 1 ” ON.

Power-up the machine using the power switch (Q1), at

the same time pressing and holding the START button

(S3).Wait for a few seconds then release the START (S3)

button.

The confirmation of the occured programming can be

attained in the following way: close the machine door. The

machine should not fill up the tank.

After that, switch off the machine with the Line (Q1)button

and wait for a few seconds. When switching on the

machine again, it should function regularly.”

95 cycles

110

cycles

45 cycles

cycles

55 cycles

cycles

75 cycles

cycles

85 cycles

100

cycles

105

cycles

115

cycles

no cycle count

cycles

65 cycles

cycles

OFF