Specifications

1. Plug the Bond Conduction
Power on/off Microphone Power on/off Microphone Headphone into the Headphone jack
Indicator Indicator of Receiver Amplifier
Brief Introduction What is Bond Conduction
Transmitter
Receiver Amplifier
How to Use
TECHNOLOGY - Bone conduction
technology delivers sound wave through
the skull to the innner ear.
KEEPING EAR DISEASE AWAY
-
Transmiter Receiver Amplifier
2. Slide the power switch of both Receiver
and Transmitter to "ON"
p
osition.
Bond
Conduction
Head
p
hone
KEEPING
EAR
DISEASE
AWAY
-
No need to put into ears, it release your
ears to allow the air to circu
Without covering thate, easy to clean, to
avoid ear disease caused by sweat.
MORE COMFORTABLE -
The sound transmits through the bone to
auditor
y
nerve
,
more comfortable an
d
B5
and
Transmitter
to
ON
position
.
Package Content :
Receiver Amplifier * 1pcs Charge input Charge input BT ON
Transmitter * 1pcs Headphone in Line in
Bond Conduction Headphone * 1pcs Volume
USB Cable * 1pcs
Amplifier and
Transmitter
Headphone
auditory
nerve,
more
comfortable
and
healthier than traditional hearing aids,
suitable to people who have trouble in
listening.
with Receiver
TransmitterReceiver Amplifier
p
3. The Indicator of Both Receiver Amplifier Alternatively, by using provide Line-in 6.Press the clamp and clip on
Use as Bluetooth headset
C. Answering a call Or Make a call
and Transmitter will be flash. Sound is Cable, TV line-out signal can be connected the cloth. A. Paring to phone
prompt for pairing start. Wait for the to Transmitter. 1. Turn On only Receiver Amplifier. Telephone conversation can done by
pairing finish and Indicator will stop speaking to Receiver Amplifier and listen
flashing. by the headset.
BT Press the answer button on the phone to
BT
Press the answer button on the phone to
4. Once pairing is finished, Transmitter answer a call and end a call by pressing
will send the sound received by 5. Adjust the volume control of Receiver hang up button on the phone.
microphone to Receiver Amplifier. Amplifier. 3. Sound prompt is heard for successful
2. Turn on Bluetooth on your phone device, connection.
scan the bluetooth devices, select RX to
7.Wear the headphone to correct connect Receiver Amplifier. B. Listen to Music
position. Enjoy Stereo sound music from mobile
Receiver Amplifier
phone through the headset.
After successful pairing. Select your music
in the phone and playback/Stop it through
your mobile control.
Use Internal Microphone
1. Plug the Bond Conduction 3. Adjust the volume control. 5.Wear the headphone to correct Specification :
Headphone into the Headphone jack. position. BlueTooth Version : 4.2
Connect the USB cable to power Distance : 10M
source and connect the other end Li Battery : 3.7V 500mAh
(Type C) to the unit. Play time : around 10 hours
Charging time : around 2.5 hours
Speaker : Bone conduction speaker
Charge the unit
USB Type Sound level : 88dB
C cable Microphone : -54dB
2. Slide the power switch to 4.Press the clamp and clip on Frequecny range : 100Hz - 18KHz
"ON" position. the cloth. Volume control : Rotary
Charge input : Type C input
ON
ON
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved
by the party responsible for compliance could void
the user's authority to operate the equipment.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in
a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment
and receiver.
-Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV
technician for help.
The device has been evaluated to meet general RF
exposure requirement. The device can be used in
portable exposure condition without restriction.