Daim Ntawv Qhia Tus Neeg Siv

ManualsBrandsHoneywell ManualsDigital ControllerHoneywell UDC2800 Universal Digital Controller

Table Of Contents

UDC2800 Universal Digital Controller Quick Start Guide

Step Operation Press Result

1 Enter Set Up Mode Setup key Enter in the first set up group, Security.

2 Select any Set Up group

Setup key or Increment

or Decrement keys

Sequentially displays the other set up groups shown in the prompt hierarchy.

See Configuration Record Sheet for prompts.

You can also use the Increment or Decrement keys to scan the set up groups

in both directions. Stop at the set up group tile that describes the group of

parameters you want to configure. Then proceed to the next step.

Select a Function

parameter

Function key Enter in the first function prompt of the selected set up group.

Increment or

Decrement keys

Press Increment or Decrement keys to display the other function prompts of

the selected set up group. Stop at the function prompt that you want to

change.

Change the Value or

Selection

Function key Enter in the value or selection of the selected function prompt.

Increment or

Decrement keys

Increment or decrement the value or selection that appears for the selected

function prompt.

You can press the Increment and Decrement keys at the same time to move the

current editable digit one step left.

Enter the Value or

Selection

Function key Enter value or selection made into memory.

6 Exit Configuration Lower Display key Exit the set up mode and returns to the main screen.

Configuration Procedure

Group

Prompt

Function Prompt Value or

Selection

Factory Setting Group

Prompt

Function Prompt Value or

Selection

Factory Setting

Algorithms Control Algorithm

Timer Function

Period Hrs:Mins

Start Trigger

Low Display

Reset Trigger

Increment

Input Algorithm 1

Math K

Calculated High

Calculated Low

Algorithm 1 Input A

Algorithm 1 Input B

Algorithm 1 Input C

Percent CO

Algorithm 1 Bias

Percent H2

――――

PID A

Disable

0.01

Keyboard

Timer Remaining

Keyboard

Minutes

None

1.0

1000

Input 1

Input 2

None

0.200

0.000

1.000

Output Output Algorithms

Output Range

Relay State

Relay Type

Motor Time

Current Output

CO Low Value

CO High Value

CO Range

――――

Model No. dependent

100 Percent

1 Off 2 On

Electromechanical

Disable

0.0

100.0

4-20mA

Input1

Input 1 Type

Input 1 Transmitter

Input 1 High Value

Input 1 Low Value

Input 1 Ratio

Input 1 Bias

Input 1 Filter

Input 1 Burnout

――――

0-10 mV

Linear

1000

1.00

No Burnout

Input2 Input 2 Type

Input 2 Transmitter

Input 2 High Value

Input 2 Low Value

Input 2 Ratio

Input 2 Bias

Input 2 Filter

Input 2 Burnout

――――

0-10 mV

Linear

1000

1.00

No Burnout

Control

PV Source

PID Sets

Switchover Value 1/2

Switchover Value 2/3

Switchover Value 3/4

Local SP Source

Remote SP Source

Autobias

SP Tracking

Power Up Mode

TPSC Power Up Mode

SP High Limit

SP Low Limit

Action Direction

Output Rate

Rate Up % Min

Rate Down % Min

Output High Limit

Output Low Limit

Integral High Limit

Integral Low Limit

Dropoff

Deadband

Output Hysteresis

Failsafe Mode

Failsafe Value

SW Failsafe Value

Preset Manual Output

Preset Auto Output

Proportion Unit

Reset Unit

――――

Input 1

1 Set

0.00

1 Local SP

None

Disable

None

Manual/Local SP

Failsafe

1000

Reverse

Disable

100

1.0

0.5

Non Latching

Gain

Minutes/Repeat

Alarms A1S1 Type

A1S1 Value

A1S1 State

A1S1 Event

A1S1 Delay

A1S1 Hysteresis

A1S2 Type

A1S2 Value

A1S2 State

A1S2 Event

A1S2 Delay

A1S2 Hysteresis

A2S1 Type

A2S1 Value

A2S1 State

A2S1 Event

A2S1 Delay

A2S1 Hysteresis

A2S2 Type

A2S2 Value

A2S2 State

A2S2 Event

A2S2 Delay

A2S2 Hysteresis

Alarm Output 1

Alarm Blocking

AO/CO Diagnostic

――――

None

High Alarm

End of Segment

0.1

None

Low Alarm

Begin of Segment

0.1

None

High Alarm

End of Segment

0.1

None

Low Alarm

Begin of Segment

0.1

Non Latching

Disable

Options

Auxiliary Output

CO Range

CO Low Value

CO High Value

DI 1 Function

DI 1 Combination

DI 2 Function

DI 2 Combination

――――

Disable

4-20 mA

0.0

100.0

None

Disable

None

Disable

Display Decimal Digits

Temperature Unit

Input 2 Ratio

Language

TC Diagnostics

Theme

――――

None

Disable

English

Enable

Bright

Configuration Record Sheet

Enter the value or selection for each prompt on this sheet so you will have a record of how your controller was configured.

Group Prompt Function Prompt Value or

Selection

Factory

Setting

Group Prompt Function Prompt Value or

Selection

Factory

Setting

Security

Password

Lockout

Auto/Man Key

Run/Hold Key

SP Select Key

Restore Settings

Restore*

Change Password

――――

Calibration

Enable

Disable

- -

Accutune

Fuzzy Suppression

Accutune

Duplex Output

Error Status

――――

Read only

Disable

Manual

None

Tuning

Proportional Band 1

Gain 1 or

Rate Min

Reset Mins/Rpt 1

Reset Rpts/Min 1

Manual Reset

Proportional Band 2

Gain 2

Rate 2 Min

Reset Mins/Rpt 2

Reset Rpts/Min 2

Proportional Band 3

Gain 3

Rate 3 Min

Reset Mins/Rpt 3

Reset Rpts/Min 3

Proportional Band 4

Gain 4

Rate 4 Min

Reset Mins/Rpt 4

Reset Rpts/Min 4

Cycle Time 1 Sec

Cycle Time 2 Sec

――――

- -

1.000

0.00

- -

1.000

0.00

1.00

- -

1.000

0.00

1.00

- -

1.000

0.00

1.00

- -

Ramp/Program

SP Ramp Function

Ramp Time Min

Ramp Final SP

SP Rate Function

Rate Up EU/HRr

Rate Down EU/Hr

SP Program Function

Soak Deviation

Program Termination

Program End State

Key Reset/Rerun

Hot Start

――――

Disable

1000

Disable

Last SP

Disable

51-52-25-158, Revision 3.0

June 2022