Install Instructions

ManualsBrandsHoneywell ManualsCommercial Thermostats & ControlsPneumatic Thermostat Direct Acting, Wall Thermostat and Beige Cover (59° to 90°F setpoint range)

TP970-72, TP970-74, TP9600, AND TP9630 PNEUMATIC SENSORS, HUMIDISTATS, AND THERMOSTATS

2. Swing cover up and over stat.

3. Place Allen wrench end of Thermostat Tool through

setscrew slot and into setscrew.

4. Rotate Thermostat Tool counterclockwise until setscrew

holds cover securely onto stat backplate (conventional

stat) or stat body (Quick-Mount stat). Repeat for other

setscrew.

Installing Cover Inserts

The following Cover Inserts are available for the setpoint and

DAY/AUTO lever slots on stat covers:

Part No. Finish

Applicable

Covers Slot

14004437 -001 Satin

Chrome

14004406-XXX

Standard Covers*

DAY/AUTO

-002 Beige

Plastic

14004407-XXX

Standard Covers*

14004438 -001 Satin

Chrome

14004406-XXX

Standard Covers*

Setpoint

-002 Beige

Plastic

14004407-XXX

Standard Covers*

14004442 -001 Black 14002132-XXX

Special Covers†

DAY/AUTO

Setpoint

* See HP970 and TP970 Series Standard Covers and

Accessories Specification Data 77-1003.

† See HP970 and TP970 Series Standard Covers

Specification Data 77-9828.

Cover Inserts are removable. Covers ship with setpoint and

DAY/AUTO lever slots “open” (without Insert) or “closed” (with

Insert present) as follows:

— Setpoint slot: Open or closed as ordered (see HP970

and TP970 Series Standard Covers and Accessories

Specification Data 77-1003 and HP970 and TP970

Series Special Covers and Accessories Specification

Data 77-9828)

— DAY/AUTO lever slot:

• No Insert on vertical stat covers

• Insert present on horizontal stat covers

Figures 18 and 19 show how to install Inserts.

COVER

INSERT

M10828

UNUSED

SLOT

Fig. 18. Installing DAY/AUTO Cover Insert

14004437-001/-002.

COVER

SETPOINT

SLOT

SETPOINT

COVER

M10827

INSERT

Fig. 19. Installing Setpoint Cover Insert

14004438-001/-002.

Painting (Beige Plastic Covers Only)

Beige Plastic Covers can be painted with recommended

paints before or after Covers are installed.

Recommended Paints

If a non-latex paint is required, use Rust-Oleum Enamel (a

fish-oil type enamel). No primer is needed.

If a latex paint is required, use one of the following as a

primer and follow with any latex wall paint:

— Sears Anti-Rust Enamel (a soya-alkyd type enamel in a

spray can)

— True Value Tru-Test X-O Stain Primer/Sealer Stain Killer

XOS-1 White (a white-pigmented, shellac type primer)

Painting Procedures

Painting Cover before Window is Installed

Order the following equipment:

— Cover Assembly 14004402-002

— DAY/AUTO Cover Insert 14004437-002 (optional)

— Setpoint Cover Insert 14004438-002 (optional)

— Window 14004405-XXX according to the following table:

1. Remove or add Inserts to Cover Assembly as required

(see INSTALLING COVER INSERTS).

2. Wash Cover Assembly with mild dish detergent solution.

3. Dry with paper towel.

4. Paint with approved paint.

5. Allow to dry.

6. When Window has been assembled to Cover,

disassembly may damage Window. Before installing

Window, note the following:

a. Check that Window display is correct for job

requirements.

b. Check Window orientation to cover. Cover

setpoint and DAY/AUTO lever slots should be on

the bottom (vertical mounting) or to the right

(horizontal mounting).

7. Remove liner from adhesive on back of Window. Slide

Window into Cover opening (Fig. 20) and press in place.

95-5597—1