VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
68-0312—05 72
Fig. 149.
Fig. 150.
Using the Temperature Display
In some circumstances, the temperature displayed on the
Home screen may not match the temperature near the
thermostat.
If your system is set up to use remote indoor sensors, it may
be reading a sensor in another location.
Fig. 151.
Using the Humidity Display
In some circumstances, the humidity displayed on the
Home screen may not match humidity near the thermostat.
Some systems are set up to use two sensors, one to control
humidification, the other for dehumidification. These
sensors are often installed in different locations.
Depending on how your thermostat was installed, the
thermostat Home screen will display humidity readings
from only one sensor.
Fig. 152.
Universal Outputs (U1, U2, U3)
U1, U2, U3 are universal outputs that can be setup to
control IAQ equipment and a stage of heating or cooling in
the Installer Setup. Setup options are listed below. See
Thermostat Wiring Guides on page 133 and Equipment
Interface Module wiring guides on page 134.
Universal Output Options
With Equipment Interface Module (U1, U2, U3):
• Humidification (ISU 803)
• Dehumidification (ISU 904)
• Ventilation (ISU 1002)
• Cool Stage 3 (ISU 208)
• Cool Stage 4 (ISU 209)
• Geothermal Radiant Heat (ISU 203, 204)
TH8321 Thermostat Only (U1)
• Humidification (ISU 803)
• Dehumidification (ISU 904)
• Ventilation (ISU 1002)
• Cool Stage 3 (ISU 208)
• Conventional Heat Stage 3 (ISU 210, 214)
• Backup Heat Stage 2 for Heat Pumps (ISU 217)
• Geothermal Radiant Heat (ISU 203)
Universal Inputs (S1, S2, S3, S4)
S1, S2, S3 and S4 are universal inputs that can be setup to
work with a sensor or dry contact device in the Installer
Setup. Setup options and compatible sensors are listed
below. See wiring diagrams on page 74 and page 140. The
thermostat has 1 Universal Input and the Equipment
Interface Module has 4 Universal Inputs.
MCR33976
Installer Options
MCR33977
Enter password
0 0 0 0
MCR33985
Temperature reading depends on location of sensor
MCR3416
Humidity reading depends on location of sensor.