VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
68-0312—05 18
Fig. 44.
NOTE: Thermostat displays a count-down timer while in
the listening mode. If it detects no activity for 15
minutes, it exits listening mode.
Locating the Connect Buttons on
RedLINK Accessories
Wireless Outdoor Sensor
1. Press and quickly release the CONNECT button on
the Wireless Outdoor Sensor. After a short delay (up
to 15 seconds), the thermostat will display “Outdoor
Sensor has been added.”
Fig. 45. Wireless outdoor sensor connect button.
Portable Comfort Control
1. Press CONNECT on the Portable Comfort Control
display screen.
Fig. 46. Portable Comfort Control connect button.
2. Press DONE on the Portable Comfort Control when it
displays “Connected.”
3. Press “No” at the next screen to save and exit, or press
“Yes” if you need to connect additional thermostats to
the Portable Comfort Control. See Fig. 47.
NOTE: The Portable Comfort Control can control up to 16
thermostats.
Fig. 47. Connect additional thermostats to Portable
Comfort Control.
4. Follow the same linking procedure as above to con-
nect additional thermostats.
ERROR MESSAGES:
E1 29: Incompatible device cannot be connected.
E1 34: Low RF signal. Move device to a different location
and try again.
E1 38: Make sure the thermostat, EIM, or TrueZONE
Wireless Adapter is in Wireless Setup mode, and the
Portable Comfort Control is at least 2 feet away (600 mm).
NOTE: The linking procedure will time out if there is no
keypress for 30 minutes. To begin again, press and
hold in the lower right corner of the screen until
the display changes (about 3 seconds). See Fig.
48.
Fig. 48. Restarting the linking process.
MCR33972
Outdoor Sensor
has been added
MCR28847A
MCR32942
CONNECT
WIRELESS SETUP
NOYES
CONNECT MORE?
M28482
Press and hold
the blank space
(or arrow may be
present)