VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
123 68-0312—05
Fig. 312. Inserting wires in thermostat terminal block.
Fig. 313. Inserting wires in EIM terminal block
IMPORTANT
Use 18–22 gauge thermostat wire.
Table 11. Wiring Diagrams by System Type.
System Type
Wiring Diagram
Reference
Standard Heat/Cool 314
Heat Pump with Auxiliary Heat 315
Geothermal radiant heat 316
Heat pump with oil forced air backup. 320
Geothermal radiant heat with
geothermal forced air and backup heat
using separate transformer for the
radiant heat
321
Wood stove-fired hot water fan coil with
forced air furnace backup heat
322
Hot water radiant heat with backup
heat (single zone application)
323
Hot water radiant heat with backup
forced air heat. Zoned with forced air
zone panel and zone valves
324
Hot water radiant heat with backup
forced air heat. Zoned with forced air
zone panel and hot water panel.
325
Hot water fan coil with forced air
furnace backup heat.
326
Wood stove with heat pump and
backup electric strips. (For applications
in which the thermostat only needs to
run the blower fan when stove is hot).
327
Wiring IAQ Equipment or a stage of
Heating/Cooling to U1, U2 or U3
terminals
328–338
Wired Remote Sensors 345–349
Table 12. Zoning Diagrams by System Type.
System Type
Wiring Diagram
Reference
RedLINK VisionPRO thermostats with
an HZ432 zone panel and no IAQ
control
350
RedLINK VisionPRO thermostat
controlling one zone with an HZ432
zone panel and a TrueSTEAM
humidifier
351
RedLINK VisionPRO thermostat with an
HZ432 zone panel and a ventilator
352
RedLINK VisionPRO thermostat with an
HZ432 zone panel and a TrueDRY
dehumidifier
353
S1
S1
W
Y
G
W2
Y2
A
S1
S1
O/B
Y
G
AUX
-E
Y2
L/A
K
RC
R
U1
U1
U2
U2
C
CONVENTIONAL
HEAT PUMP
R
C
Y
Y2
G
W
O/B
W2
AUX1
W3
AUX2
A
L/A