VisionPRO 8000 Spec Sheet 2017

ManualsBrandsHoneywell ManualsBuilding SuppliesHoneywell TH8321R1001 Vision pro 8000 Thermostat

121

122

123

124

125

126

127

128

129

130

Table Of Contents

Application
Features
Contents
Specifications
System Installation
- When Installing this Product...
- Finding Your Password (Date Code)
Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
Power Optional RedLINK™ Accessories
Performing Initial Setup
- Linking Thermostat to Equipment Interface Module (if used)
- Linking RedLINK Accessories
- Completing Initial Setup
- Adding RedLINK Accessories to the Thermostat
- Locating the Connect Buttons on RedLINK Accessories
- Finding Your Password (Date Code) to Access Installer Options
- Make Changes to Installer Setup
Installer Tests
- Accessing Installer Tests
- Using the Equipment Test
- Using the Wireless Signal Strength Test
- Mounting Optional Accessories
Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
Heat Pump and Backup Heat Operation
- Heat pump with outdoor temperature lockouts
- Geothermal Radiant Heat
Indoor Air Quality (IAQ) Control
- Humidification
- Dehumidification - Residential
- Dehumidification - Commercial
- Ventilation
- Ventilation Options
IAQ Reminders
Customizable Reminders
MicroSD card
- Updating Thermostat Software
- Loading Dealer Information
- To Use the MicroSD Card in the Thermostat
Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
Optional Accessories
Portable Comfort Control
Remote Indoor Sensors
- Indoor Sensor Operation
- Wireless Indoor Sensor
- Backup Control
Replacing a Thermostat
Replacing an Equipment Interface Module
Wiring
- EIM Wiring Diagrams
- Wiring IAQ Equipment or a Heat/Cool Stage to the Universal Terminals
- Wiring IAQ Equipment or a Heat/Cool Stage to the Universal Terminals
- Economizer Module Wiring Diagrams
- Wiring C7089U1006 Outdoor Sensor
- Wiring guide — Wired Indoor Sensors
Zoning
- Zoning and Humidification
- Zoning and Ventilation
- TrueDRY dehumidifier with Zoning
- Zoning FAQs
Troubleshooting
Regulatory Information

VISIONPRO

8000 WITH REDLINK™

68-0312—05 122

* Remove factory installed jumper for two transformer systems.

†

The THP9045A1023 Wire Saver module is used on heat/cool systems when you only have four wires at the thermostat

and you would like the thermostat to be powered with a common wire. Use the K terminal in place of the Y and G terminals

on conventional or heat pump systems to provide control of the fan and the compressor through a single wire—the

unused wire then becomes your common wire. See THP9045 instructions for more information.

CAUTION

Electrical Hazard.

Can cause electrical shock or equipment damage.

Disconnect power before wiring.

All wiring must comply with local electrical codes and

ordinances. See Fig. 314–353.

1. Select wiring diagram that corresponds with system

type and the equipment being installed (using the

EIM or wiring the thermostat directly to the HVAC

equipment).

2. Loosen the screws for the appropriate terminals.

Insert wires in the terminal block under the loosened

screw. See Fig. 312 and 313.

3. Securely tighten each screw.

4. Push excess wire back into the hole.

5. Plug the hole with nonflammable insulation to pre-

vent drafts from affecting the thermostat.

6. See Fig. 314–338 for typical wiring hookups.

Table 10. Thermostat Terminal Designation Descriptions.

Conventional System Heat Pump

Terminal Description Terminal Description

C Common wire from secondary side of cooling

transformer (if 2 transformers).

C Common wire from secondary side of cooling

transformer.

Rc* Cooling power Rc Cooling power

R* Heating power R Heating power

W Heat Stage 1 O / B Changeover valve for heat pumps

W2 Heat Stage 2 AUX-E Backup Heat/Emergency Heat

Y Compressor Stage 1 Y Compressor Stage 1

Y2 Compressor Stage 2 Y2 Compressor Stage 2

G Fan Relay G Fan Relay

A Connect to Economizer Module or Lighting Panel

(TOD).

L / A Connect to Compressor Monitor, Zone Panel,

Economizer Module or Lighting Panel (TOD).

U1 / U1 Universal relay for humidification,

dehumidification, ventilation, or a stage of

heating/cooling.

Economizer control with fault.