Datasheet

ManualsBrandsHONEYWELL ManualsSensorsPosition sensor Reading range: 360 ° (max) Analogue amperage M12 (5-pin)

12345678910111213141516

HONEYWELL

PART NUMBER

FO-55175-A

SIZE

SHEET

SCALE

REV

TYPE

TITLE

DRAWN

CHECK

Pro/ENGINEER

THIS DRAWING COVERS A PROPRIETARY ITEM

AND IS THE PROPERTY OF HONEYWELL.

THIS DRAWING IS NOT TO BE COPIED OR USED

WITHOUT THE PERMISSION OF HONEYWELL.

TOLERANCES UNLESS NOTED:

DRAWING NAME

CAGE_CODE

PLEASE REFER TO

PERFORMANCE SPEC TABLE FOR

LINEARITY OF FULL SCALE RANGE

MEASUREMENT ANGLE ( )

( )80

(3X )12.5

1" DIAMETER SHOWN

SEE SPS-MAG-SERIES-CHART-1 FOR OTHER OPTIONS OR REQUEST CUSTOM SIZE

(14 )

(45.10 )

(19 )

(20.5 )

(1.6 )

( )64

22.00 0.20

30.00 0.15

0.4 A B

3X 5.80 0.15

3X 92.50

3X 120

REV

DOCUMENT

CHANGED BY CHECK

B 0089219 PSP 08MAY12 RS

SPS-R360D-NBMS0101

1 OF 2

SPS ROTARY 360 DEGREE 4 TO 20 MA

ANDY CHEN 28DEC11

JL 15MAR12

2:1

DESIGN UNITS: MM

INTERPRET PER ASME Y14.5M-1994

OTHER HONEYWELL ENGINEERING

STANDARDS MAY APPLY

I - SPS-R360D-NBMS0101 B

PERFORMANCE SPEC TABLE

PARAMETER MIN TYP MAX UNITS CONDITIONS

MEASUREMENT DISTANCE 0 --- 360 Degree( ) ---

AIR GAP 1 3 5 MM ---

LINEARITY -0.03 --- 0.030 %FS 25 C

LINEARITY TC --- --- 0.0011 (%FS/DEG C) -40>T<85 C

OFFSET -0.036 -0.011 0.015 %FS 25 C

OFFSET TC --- --- 0.0033 %FS/DEG C -40>T<85 C

ACCURACY -0.069 --- 0.069 %FS 25 C

SENSITIVITY 44.43 44.45 44.47 uA / DEGREE 25 C

SENSITIVITY TC --- --- 80 PPM / DEG C -40>T<85 C

RESOLUTION --- 0.01 --- DEGREE C ---

START UP TIME --- 130 --- mS ---

% LINEARITY

RADIAL ERROR (mm) 0 0.05 0.1 0.25 0.5 0.75 1 1.5 2 2.5

AXIAL ERROR (mm)

-2 -0.005 0.001 0.007 0.027 0.066 0.113 0.166 0.294 0.450 0.635

-1 -0.002 0.003 0.008 0.025 0.060 0.101 0.150 0.269 0.417 0.593

0 0.000 0.004 0.008 0.023 0.053 0.090 0.135 0.245 0.383 0.550

1 0.002 0.005 0.009 0.021 0.047 0.079 0.119 0.220 0.350 0.508

2 0.005 0.007 0.009 0.019 0.040 0.068 0.104 0.196 0.317 0.466

3 0.007 0.008 0.010 0.017 0.033 0.057 0.088 0.172 0.284 0.424

% ACCURACY

RADIAL ERROR (mm) 0 0.05 0.1 0.25 0.5 0.75 1 1.25 2 2.5

AXIAL ERROR (mm)

-2 0 0.006 0.012 0.033 0.076 0.129 0.191 0.263 0.538 0.770

-1 0 0.005 0.011 0.029 0.069 0.118 0.176 0.245 0.509 0.733

0 0 0.004 0.009 0.026 0.061 0.106 0.162 0.226 0.479 0.697

1 0 0.004 0.008 0.022 0.054 0.095 0.147 0.208 0.450 0.660

2 0 0.003 0.006 0.018 0.047 0.084 0.132 0.190 0.420 0.623

3 0 0.002 0.005 0.015 0.039 0.073 0.117 0.171 0.391 0.586

DEFINITIONS:

1 - LINEARITY: DEVIATIONS FROM A BEST FIT STRAIGHT LINE THROUGH THE OUTPUT, EXPRESSED AS A

PERCENTAGE OF THE FULL SCALE SIGNAL RANGE (% OF 16mA).

2 - ACCURACY: DEVIATIONS FROM THE IDEAL OUTPUT LINE EXPRESSED AS A PERCENTAGE OF THE

FULL SCALE SIGNAL RANGE (% OF 16mA).

3 - %FS: ERROR EXPRESSED AS A PERCENTAGE OF THE OUTPUT SPAN OF THE SENSOR (% OF 16mA).

4 - OFFSET: DEVIATION FROM THE IDEAL OUTPUT AT THE MINIMUM INPUT CONDITION, EXPRESSED AS A

PERCENTAGE OF THE FULL SCALE SIGNAL RANGE (% OF 16mA).

5 - SENSITIVITY: THE SLOPE OF THE OUTPUT SIGNAL VS MAGNET TRAVEL, EXPRESSED AS uA'S OF OUTPUT

PER DEGREE OF TRAVEL.

6 - TC: TEMPERATURE COEFFICIENT OF A GIVEN PARAMETER, AS A PERCENTAGE OF THE FULL SCALE

SIGNAL RANGE (% OF 16mA) PER DEGREE OF TEMPERATURE RISE FROM ROOM.

7 - Vcc=SUPPLY VOLTAGE(+)

8 - RADIAL ERROR = DISTANCE BETWEEN SENSOR AXIS AND MAGNET COLLAR AXIS (SHAFT AXIS)

REF POINT "B"

OUTPUT SIGNAL (mA)

NOMINAL SIGNAL OUTPUT CURVE

(THROUGH REFERENCE POINTS "A" AND "B")

SENSOR OUTPUT PERFORMANCE CHART

REF POINT "A"

135

180

225

270

315

360

-45

405

NOTES:

1 - IDEAL OUTPUT @ REF POINT A [DELTA A=0 ]: 4mA

2 - IDEAL OUTPUT @ REF POINT B [DELTA B=360 ]: 20mA

3 - OPERATING CONDITIONS:

TEMP RANGE -40 C TO 85 C

SUPPLY VOLTAGE 12 TO 30 VDC

SUPPLY CURRENT 90mA MAX

4 - MOUNTING : MOUNT SENSOR ON THE EPOXY SIDE

MOUNTING SCREWS: UNC 10-24 OR M5

RECOMMENDED INSTALLATION TORQUE: 44.25 TO 61.95 IN-LBS (5 TO 7 N.M)

5 - ROTATION OF MAGNET IS COUNTER CLOCKWISE AS PICTURED WITH MAGNET BELOW SENSOR (EPOXY SIDE).

6 - LASER MARKING INCLUDES HONEYWELL PART #, DATE CODE & SERIAL #

7 - CONNECTOR PIN ASSIGNMENTS

1 - SUPPLY VOLTAGE(+)

2 - TEST PIN,CONNECT TO GROUND(-)

3 - GROUND(-)

4 - OUTPUT(O)

5 - TEST PIN,CONNECT TO GROUND(-)

8 - FERROUS MATERIAL WITHIN 100 MM (3.9") RADIUS OF MAGNET MAY IMPACT SENSOR PERFORMANCE

9 - TOLERANCE APPLIES FOR FULL SENSE RANGE

10 - PLEASE FOLLOW CONNECTOR SUPPLIER RECOMMENDATION TO INSTALL MATING M12 5 PINS CONNECTOR.

11 - PERFORMANCE TABLE BASED UPON NON-FERROUS SHAFT.

12 - MAGNET ASSEMBLY IS SOLD SEPARATELY.

CONNECTOR PIN ASSIGNMENT

M12 CONNECTOR,MALE,5 PINS

REF: 0

CABLE

DIRECTION FOR

RIGHT ANGLE CONNECTOR

IMPACT OF MAGNET MISPOSITION TABLES

(3xR8.25)

SECTION

A-A

MAGNET

MOUNTING SURFACE