Datasheet

11
Infrared Sensors
Optoschmitt: Detectors and Sensors
Series SD5600 SD5610 SD5620 SD5630 SDP8600 SDP8610 HOA096X/
HOA097X
HOA696X/
HOA697X
HOA698X/
HOA699X
HOA7720/
HOA7730
Type
detector detector detector detector detector detector sensor sensor sensor sensor
Package style/
housing
TO-46 dome lensed TO-46 dome lensed TO-46 dome lensed TO-46 dome lensed side-detecting side-detecting transmissive/opaque transmissive/opaque transmissive/opaque transmissive
Package
components
metal metal metal metal plastic plastic – – – –
Angular response
12° 12° 12° 12° 50° 50° – – – –
Turn-on threshold
irradiance
2.5 mW/cm
2
max. 2.5 mW/cm
2
max. 0.25 mW/cm
2
0.25 mW/cm
2
2.5 mW/cm
2
max. 2.5 mW/cm
2
max. – – – –
Output logic
buffer inverter buffer inverter buffer inverter – – – –
Supply voltage
(range)
4.5 Vdc to 16 Vdc 4.5 Vdc to 16 Vdc 4.5 Vdc to 16 Vdc 4.5 Vdc to 16 Vdc 4.5 Vdc to 12 Vdc 4.5 Vdc to 12 Vdc – – – –
Sensor aperture
– – – – – –
1,52 mm x 0,25 mm
[0.06 in x 0.01 in];
1,52 mm x 1,27 mm
[0.06 in x 0.05 in]
1,52 mm x 0,25 mm
[0.06 in x 0.01 in];
1,52 mm x 1,27 mm
[0.06 in x 0.05 in]
1,52 mm x 0,25 mm
[0.06 in x 0.01 in];
1,52 mm x 1,27 mm
[0.06 in x 0.05 in]
1,78 mm x 0,51 mm
[0.07 in x 0.02 in];
1,52 mm x 1,27 mm
[0.06 in x 0.05 in]
Slot width
– – – – – – 3,18 mm [0.125 in] 3,18 mm [0.125 in] 3,18 mm [0.125 in] 3 mm [0.118 in]
Output type
– – – – – – 10 kOhm pull-up
open collector/totem-pole
10 kOhm pull-up
open collector/totem-pole
10 kOhm pull-up
open collector/totem-pole
Output logic
– – – – – – buffer/inverter buffer/inverter buffer/inverter inverter
Supply voltage
– – – – – – 4.5 V to 10 V 4.5 V to 7 V 4.5 V to 12 V 4.5 V to 5.5 V
Rise/fall time
– – – – – – 60 ns tr/15 ns tf 70 ns tr/70 ns tf 70 ns tr/70 ns tf 70 ns tr/70 ns tf
Propagation delay
– – – – – –
5 ms 5 ms 5 ms 5 ms
Mounting
configuration
through-hole through-hole through-hole through-hole through-hole through-hole N, L, T, P mounting options N, L, T, P mounting options N, L, T, P mounting options mounting tabs
Termination style
0,46 mm [0.018 in]
round leads
0,46 mm [0.018 in]
round leads
0,46 mm [0.018 in]
round leads
0,46 mm [0.018 in]
round leads
0,51 mm [0.020 in] sq leads 0,51 mm [0.020 in] sq leads 0,51 mm [0.020 in] sq leads 0,51 mm [0.020 in] sq leads 26 AWG wire leads integral 3-pin connector
Measurements
Ø 4,06 mm x 17,77 mm L
[Ø 0.160 in x 0.688 in L]
Ø 4,06 mm x 17,77 mm L
[Ø 0.160 in x 0.688 in L]
Ø 5,56 mm x 17,77 mm L
[Ø 0.219 in x 0.688 in L]
Ø 5,56 mm x 17,77 mm L
[Ø 0.219 in x 0.688 in L]
1,52 mm H x 4,45 mm W
x 18,43 mm L [0.06 in H x
0.175 in W x 0.725 in L]
1,52 mm H x 4,45 mm W
x 18,43 mm L [0.06 in H x
0.175 in W x 0.725 in L]
11,05 mm H x 24,89 mm W
x 21,23 mm L [0.44 in H x
0.98 in W x 0.835 in L]
11,05 mm H x 24,89 mm W
x 21,23 mm L [0.44 in H x
0.98 in W x 0.835 in L]
11,05 mm H x 24,89 mm W
x 21,23 mm L [0.44 in H x
0.98 in W x 0.835 in L]
6,0 mm H x 6,4 mm W x
31,5 mm L [0.236 in H x
0.27 in W x 1.24 in L]
Features
6° nominal acceptance
angle; enhanced noise
immunity; TTL/LSTTL/
CMOS compatible; buffer
logic
6° nominal acceptance
angle; enhanced noise
immunity; TTL/LSTTL/
CMOS compatible;
inverting logic
6° nominal acceptance
angle; enhanced noise
immunity; TTL/LSTTL/
CMOS compatible; buffer
logic; two sensitivity
ranges
6° nominal acceptance
angle; enhanced noise
immunity; TTL/LSTTL/
CMOS compatible;
inverting logic; two
sensitivity ranges
wide sensitivity ranges; TTL/
LSTTL/CMOS compatible;
buffer logic; three different
lead spacing arrangements
wide sensitivity ranges; TTL/
LSTTL/CMOS compatible;
inverting logic; three
different lead spacing
arrangements
direct TTL interface; four
mounting configurations;
buffer or inverting logic
direct TTL interface; buffer
or inverting logic; three
device output options; four
mounting configurations
direct TTL interface; buffer
or inverting logic; three
device output options; four
mounting configurations
direct TTL interface; infrared
emitter internally biased; no
interface circuits required;
inverting logic; totem-pole
or open collector output
options