ADEMCO Optiflex Video Controller Installation and Setup Guide K0948V2 11/04 Rev.
Table of Contents • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Ssection 1: General Information .......................................................................................................... 1-1 Introduction to Optiflex........................................................................................................................................................1-1 Optiflex Features ......................................................
S E C T I O N 1 General Information • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • In This Section ♦ Introduction to Optiflex ♦ Optiflex Typical System Block Diagram ♦ Optiflex Features • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Introduction to Optiflex Optiflex is an interactive Video System that provides multiplexed local and remote video monitoring for up to six cameras.
Optiflex Installation and Setup Guide Optiflex Typical System Block Diagram A typical Optiflex System Block Diagram is shown in Figure 1. Optiflex can be used in a variety of applications.
S E C T I O N 2 Mounting, Wiring, and Setup • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • In This Section ♦ Wiring and Setup of Optiflex ♦ Setup Considerations ♦ Mounting Optiflex • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Setup Considerations Cameras connected to Optiflex can either be triggered by system events from a Honeywell Vista control panel, from the voltage triggers provided, or both.
Optiflex Installation and Setup Guide • Voltage Trigger and Output Programming commands are interchangeable for turning on a camera. • “All Cameras” function captures a single frame from each camera. • NTSC Advance function allows you to step through the video of all cameras sequentially, one camera at a time, and then the Guard Tour. It does not support video capturing. Mounting Optiflex Optiflex must be mounted indoors. following steps: To mount Optiflex, see Figure 2 and complete the 1.
Section 2: Mounting and Wiring Wiring and Setup of Optiflex Before wiring Optiflex, make sure power is turned off and review the important notes below. 1. Use a Listed Class 2 power supply suited for the application (see Section 5: Specifications). 2. Panel triggered UL Installations: Optiflex may be connected as a supplemental device to listed fire and/or burglar alarm control panels that support the 4204 relay module except as noted below.
Optiflex Installation and Setup Guide To wire Optiflex, refer to the Summary of Connections diagram at the rear of this guide and do the following. 1. Connect the wires to the header as follows: a. Connect the (+) terminal of the supplementary power supply to header position 1 (+12VDC terminal of Optiflex (red wire)). b. Connect the (–) terminal of the supplementary power supply to header position 2 (Gnd terminal of Optiflex (black wire)).
Section 2: Mounting and Wiring NTSC Output Configuration Selects either one camera or guard tour (camera scanning) for default local viewing through a monitor.
Optiflex Installation and Setup Guide Optiflex can be reset to its default settings by pressing and holding the top reset button for 10 seconds.
S E C T I O N 3 Setting Up Optiflex Using Symphony • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • In This Section ♦ How to Select Video from the System Options ♦ How to Set Up Video Options on the Symphony • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • How to Enable Video on Symphony Symphony can either be used to view video events locally when attached to a Honeywell Vista control panel, or to view e
Optiflex Installation and Setup Guide How to Set Up Video Options on Symphony 1. Press the SECURITY button on the “Home” screen. The “Arming” screen is displayed. 2. Press the MORE CHOICES button. The “More Choices” screen is displayed. 3. Press the SETUP button on the “More Choices” screen. The “Setup” screen is displayed. 4. Press the ADVANCED SETUP button. displayed. The “Enter Authorized Code:” screen is 5. Enter your 4-digit Installer code. The “Advanced Setup” menu screen is displayed. 6.
S E C T I O N 4 Operational Status Indicators • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Camera Status LEDs Cameras 1 – 6 LEDs ON – Camera detected OFF – No camera detected Fast Flashing – Camera being viewed Slow Flash – Camera lost Network Status LEDs LINK – ON when Ethernet link is detected and OFF when Ethernet link is not detected. SELECT – Flashing indicates Ethernet Controller activity.
Optiflex Installation and Setup Guide Optiflex Status LEDs Camera Status Off – All detected cameras are connected Flashing – At least one camera lost.
S E C T I O N 5 Specifications • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Specifications MECHANICAL Dimensions: Width 7 ½ inches Height 6 ½ inches Depth 1 ¼ inches ELECTRICAL Operating Voltage: Power: 12VDC nominal Video: 1V p-p Unbalanced Current: 600mA, without camera 1.
Optiflex Installation and Setup Guide 5-2
S E C T I O N 6 Summary of Connections • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • DETAIL A DIP SWITCH DETAIL B COMPOSITE VIDEO OUT ON 12345678 PRESS AND HOLD BOTH (10 SECONDS) UNIT RESET CAMERA INPUTS (DETAIL C) 10 baseT ETHERNET 3 TRIGGER 1 TRIGGER 2 TRIGGER 3 TRIGGER 4 TRIGGER 5 TRIGGER 6 TRIGGER 7 TRIGGER 8 GND +12V -GND ECP GRN ECP YEL N.C.
Optiflex Installation and Setup Guide 6-2
NOTES
NOTES
LIMITED WARRANTY Honeywell International Inc.
165 Eileen Way, Syosset, NY 11791 Copyright 2004 Honeywell International Inc. www.honeywell.com/security ÊK0948V2pŠ K0948V2 11/04 Rev.
