Datasheet

2
sensing.honeywell.com
HEAVY DUTY, MEDIA-ISOLATED PRESSURE TRANSDUCERS, MIP SERIES
TABLE 3. PERFORMANCE SPECIFICATIONS (AT 25°C [77°F] AND UNDER UNLESS OTHERWISE NOTED.)
CHARACTERISTIC PARAMETER
Operating temperature range -40°C to 125°C [-40°F to 257°F]
Total Error Band
1
(-40°C to 125°C [-40°F to 257°F])
±1.0 %FSS (<10 bar)
2
±0.75 %FSS (>10 bar)
Accuracy BFSL
3
±0.15 %FSS
Long term stability (1000 hr, 25°C [77°F]) ±0.25 %FSS
Minimum output resolution 0.03 %FSS
Response time 1 ms (10% to 90% step change in pressure)
Startup time
4
<7ms
EMC rating (CE Conformity):
surge immunity (all leads)
electrostatic discharge
radiated immunity
fast transient burst
immunity to conducted disturbances
radiated emissions
±1 kV line to ground per IEC 61000-4-5
±4 kV contact, ±8 kV air per IEC 61000-4-2
10 V/m (80 MHz to 1000 MHz) per IEC 61000-4-3
±1 kV per IEC 61000-4-4
3 V (150 kHz to 80 MHz) per IEC 61000-4-6
40 dBμV (30 MHz to 230 MHz), 47 dBμV (230 MHz to 1000 MHz) per CISPR 11
Radiated immunity 100 V/m (200 MHz to 2 GHz) per ISO 11452-2
Insulation resistance >100 MΩ at 1 kVdc (60 s)
Dielectric strength <1 mA at 500 Vac (60 s)
Load resistance ≥2 kΩ (pull up or pull down)
Life >10 million full scale pressure cycles
1
Total Error Band: The maximum deviation from the ideal transfer function over the entire compensated temperature and pressure
range. Includes all errors due to offset, full scale span, pressure non-linearity, pressure hysteresis, pressure non-repeatability,
thermal effect on offset, thermal effect on span, and thermal hysteresis (see Figure 4).
2
TEB: ±1.5 % FSS above 100°C [212°F] for pressure ratings less than 4 bar [58 psi].
3
Accuracy: The maximum deviation in output from a Best Fit Straight Line (BFSL) fitted to the output measured over the pressure
range at 25°C [77°F]. Includes all errors due to pressure non-linearity, pressure hysteresis, and pressure non-repeatability.
4
Startup time: The time needed to receive valid output after power up.
TABLE 2. ELECTRICAL SPECIFICATIONS (AT 25°C [77°F] AND UNDER UNLESS OTHERWISE NOTED.)
CHARACTERISTIC PARAMETER
Supply voltage 5.0 ±0.25 Vdc
Nominal output transfer function (5 Vdc supply) 0.5 Vdc to 4.5 Vdc
Over/reverse voltage ±40 Vdc
Current consumption 6.5 ±1 mA
Short circuit protection yes
TABLE 4. ENVIRONMENTAL AND MECHANICAL SPECIFICATIONS
CHARACTERISTIC PARAMETER
Shock 100 G per MIL-STD-202, Method 213, Cond. C (at 25°C [77°F])
Vibration 20 G sweep, 10 Hz to 2000 Hz (at 25°C [77°F])
Ingress protection IP67
External freeze/thaw resistance >6 cycles from -30°C to 50°C [-22°F to 122°F]
Wetted materials:
port
diaphragm
external seal for ports
stainless steel 304L
stainless steel 316L
nitrile (-30°C to 100°C [-22°F to 212°F]) (other materials available)
Electrical connector material PBT 30%GF (UL V-0)